summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--drivers/ram/octeon/octeon3_lmc.c34
1 files changed, 17 insertions, 17 deletions
diff --git a/drivers/ram/octeon/octeon3_lmc.c b/drivers/ram/octeon/octeon3_lmc.c
index 349abc179f..eaef0fa5c1 100644
--- a/drivers/ram/octeon/octeon3_lmc.c
+++ b/drivers/ram/octeon/octeon3_lmc.c
@@ -2050,7 +2050,7 @@ static int compute_vref_val(struct ddr_priv *priv, int if_num, int rankx,
lmc_control.u64 = lmc_rd(priv, CVMX_LMCX_CONTROL(if_num));
/*
- * New computed vref = existing computed vref – X
+ * New computed vref = existing computed vref - X
*
* The value of X is depending on different conditions.
* Both #122 and #139 are 2Rx4 RDIMM, while #124 is stacked
@@ -2058,7 +2058,7 @@ static int compute_vref_val(struct ddr_priv *priv, int if_num, int rankx,
*
* 1. Stacked Die: 2Rx4
* 1-slot: offset = 7. i, e New computed vref = existing
- * computed vref – 7
+ * computed vref - 7
* 2-slot: offset = 6
*
* 2. Regular: 2Rx4
@@ -9941,11 +9941,11 @@ static int test_dram_byte_hw(struct ddr_priv *priv, int if_num, u64 p,
* NOTE: this step done in the calling routine(s)...
* 3) Setup GENERAL_PURPOSE[0-2] registers with the data pattern
* of choice.
- * a. GENERAL_PURPOSE0[DATA<63:0>] – sets the initial lower
+ * a. GENERAL_PURPOSE0[DATA<63:0>] - sets the initial lower
* (rising edge) 64 bits of data.
- * b. GENERAL_PURPOSE1[DATA<63:0>] – sets the initial upper
+ * b. GENERAL_PURPOSE1[DATA<63:0>] - sets the initial upper
* (falling edge) 64 bits of data.
- * c. GENERAL_PURPOSE2[DATA<15:0>] – sets the initial lower
+ * c. GENERAL_PURPOSE2[DATA<15:0>] - sets the initial lower
* (rising edge <7:0>) and upper (falling edge <15:8>) ECC data.
*/
@@ -9980,8 +9980,8 @@ static int test_dram_byte_hw(struct ddr_priv *priv, int if_num, u64 p,
/*
* 7) Set PHY_CTL[PHY_RESET] = 1 (LMC automatically clears this as
- * it’s a one-shot operation). This is to get into the habit of
- * resetting PHY’s SILO to the original 0 location.
+ * it's a one-shot operation). This is to get into the habit of
+ * resetting PHY's SILO to the original 0 location.
*/
phy_ctl.u64 = lmc_rd(priv, CVMX_LMCX_PHY_CTL(if_num));
phy_ctl.s.phy_reset = 1;
@@ -10013,9 +10013,9 @@ static int test_dram_byte_hw(struct ddr_priv *priv, int if_num, u64 p,
* a. COL, ROW, BA, BG, PRANK points to the starting point
* of the address.
* You can just set them to all 0.
- * b. RW_TRAIN – set this to 1.
- * c. TCCD_L – set this to 0.
- * d. READ_CMD_COUNT – instruct the sequence to the how many
+ * b. RW_TRAIN - set this to 1.
+ * c. TCCD_L - set this to 0.
+ * d. READ_CMD_COUNT - instruct the sequence to the how many
* writes/reads.
* It is 5 bits field, so set to 31 of maximum # of r/w.
*/
@@ -10063,9 +10063,9 @@ static int test_dram_byte_hw(struct ddr_priv *priv, int if_num, u64 p,
/*
* 6) Read MPR_DATA0 and MPR_DATA1 for results.
- * a. MPR_DATA0[MPR_DATA<63:0>] – comparison results
+ * a. MPR_DATA0[MPR_DATA<63:0>] - comparison results
* for DQ63:DQ0. (1 means MATCH, 0 means FAIL).
- * b. MPR_DATA1[MPR_DATA<7:0>] – comparison results
+ * b. MPR_DATA1[MPR_DATA<7:0>] - comparison results
* for ECC bit7:0.
*/
mpr_data0 = lmc_rd(priv, CVMX_LMCX_MPR_DATA0(if_num));
@@ -10073,8 +10073,8 @@ static int test_dram_byte_hw(struct ddr_priv *priv, int if_num, u64 p,
/*
* 7) Set PHY_CTL[PHY_RESET] = 1 (LMC automatically
- * clears this as it’s a one-shot operation).
- * This is to get into the habit of resetting PHY’s
+ * clears this as it's a one-shot operation).
+ * This is to get into the habit of resetting PHY's
* SILO to the original 0 location.
*/
phy_ctl.u64 = lmc_rd(priv, CVMX_LMCX_PHY_CTL(if_num));
@@ -10163,11 +10163,11 @@ static void setup_hw_pattern(struct ddr_priv *priv, int lmc,
/*
* 3) Setup GENERAL_PURPOSE[0-2] registers with the data pattern
* of choice.
- * a. GENERAL_PURPOSE0[DATA<63:0>] – sets the initial lower
+ * a. GENERAL_PURPOSE0[DATA<63:0>] - sets the initial lower
* (rising edge) 64 bits of data.
- * b. GENERAL_PURPOSE1[DATA<63:0>] – sets the initial upper
+ * b. GENERAL_PURPOSE1[DATA<63:0>] - sets the initial upper
* (falling edge) 64 bits of data.
- * c. GENERAL_PURPOSE2[DATA<15:0>] – sets the initial lower
+ * c. GENERAL_PURPOSE2[DATA<15:0>] - sets the initial lower
* (rising edge <7:0>) and upper
* (falling edge <15:8>) ECC data.
*/