diff options
Diffstat (limited to 'common')
-rw-r--r-- | common/Kconfig | 159 |
1 files changed, 85 insertions, 74 deletions
diff --git a/common/Kconfig b/common/Kconfig index 2d86dd7e63..7872bc46cd 100644 --- a/common/Kconfig +++ b/common/Kconfig @@ -647,28 +647,12 @@ config LOG discarded if not needed. Logging supports various categories and levels of severity. -config SPL_LOG - bool "Enable logging support in SPL" - depends on LOG - help - This enables support for logging of status and debug messages. These - can be displayed on the console, recorded in a memory buffer, or - discarded if not needed. Logging supports various categories and - levels of severity. - -config TPL_LOG - bool "Enable logging support in TPL" - depends on LOG - help - This enables support for logging of status and debug messages. These - can be displayed on the console, recorded in a memory buffer, or - discarded if not needed. Logging supports various categories and - levels of severity. +if LOG config LOG_MAX_LEVEL int "Maximum log level to record" - depends on LOG - default 5 + default 6 + range 0 9 help This selects the maximum log level that will be recorded. Any value higher than this will be ignored. If possible log statements below @@ -685,14 +669,15 @@ config LOG_MAX_LEVEL 8 - debug content 9 - debug hardware I/O -config SPL_LOG_MAX_LEVEL - int "Maximum log level to record in SPL" - depends on SPL_LOG - default 3 +config LOG_DEFAULT_LEVEL + int "Default logging level to display" + default LOG_MAX_LEVEL + range 0 LOG_MAX_LEVEL help - This selects the maximum log level that will be recorded. Any value - higher than this will be ignored. If possible log statements below - this level will be discarded at build time. Levels: + This is the default logging level set when U-Boot starts. It can + be adjusted later using the 'log level' command. Note that setting + this to a value above LOG_MAX_LEVEL will be ineffective, since the + higher levels are not compiled in to U-Boot. 0 - emergency 1 - alert @@ -705,10 +690,38 @@ config SPL_LOG_MAX_LEVEL 8 - debug content 9 - debug hardware I/O -config TPL_LOG_MAX_LEVEL - int "Maximum log level to record in TPL" - depends on TPL_LOG +config LOG_CONSOLE + bool "Allow log output to the console" + default y + help + Enables a log driver which writes log records to the console. + Generally the console is the serial port or LCD display. Only the + log message is shown - other details like level, category, file and + line number are omitted. + +config LOG_SYSLOG + bool "Log output to syslog server" + depends on NET + help + Enables a log driver which broadcasts log records via UDP port 514 + to syslog servers. + +config SPL_LOG + bool "Enable logging support in SPL" + depends on LOG + help + This enables support for logging of status and debug messages. These + can be displayed on the console, recorded in a memory buffer, or + discarded if not needed. Logging supports various categories and + levels of severity. + +if SPL_LOG + +config SPL_LOG_MAX_LEVEL + int "Maximum log level to record in SPL" + depends on SPL_LOG default 3 + range 0 9 help This selects the maximum log level that will be recorded. Any value higher than this will be ignored. If possible log statements below @@ -725,14 +738,37 @@ config TPL_LOG_MAX_LEVEL 8 - debug content 9 - debug hardware I/O -config LOG_DEFAULT_LEVEL - int "Default logging level to display" - default 6 +config SPL_LOG_CONSOLE + bool "Allow log output to the console in SPL" + default y help - This is the default logging level set when U-Boot starts. It can - be adjusted later using the 'log level' command. Note that setting - this to a value above LOG_MAX_LEVEL will be ineffective, since the - higher levels are not compiled in to U-Boot. + Enables a log driver which writes log records to the console. + Generally the console is the serial port or LCD display. Only the + log message is shown - other details like level, category, file and + line number are omitted. + +endif + +config TPL_LOG + bool "Enable logging support in TPL" + depends on LOG + help + This enables support for logging of status and debug messages. These + can be displayed on the console, recorded in a memory buffer, or + discarded if not needed. Logging supports various categories and + levels of severity. + +if TPL_LOG + +config TPL_LOG_MAX_LEVEL + int "Maximum log level to record in TPL" + depends on TPL_LOG + default 3 + range 0 9 + help + This selects the maximum log level that will be recorded. Any value + higher than this will be ignored. If possible log statements below + this level will be discarded at build time. Levels: 0 - emergency 1 - alert @@ -745,29 +781,8 @@ config LOG_DEFAULT_LEVEL 8 - debug content 9 - debug hardware I/O -config LOG_CONSOLE - bool "Allow log output to the console" - depends on LOG - default y - help - Enables a log driver which writes log records to the console. - Generally the console is the serial port or LCD display. Only the - log message is shown - other details like level, category, file and - line number are omitted. - -config SPL_LOG_CONSOLE - bool "Allow log output to the console in SPL" - depends on SPL_LOG - default y - help - Enables a log driver which writes log records to the console. - Generally the console is the serial port or LCD display. Only the - log message is shown - other details like level, category, file and - line number are omitted. - config TPL_LOG_CONSOLE bool "Allow log output to the console in TPL" - depends on TPL_LOG default y help Enables a log driver which writes log records to the console. @@ -775,26 +790,10 @@ config TPL_LOG_CONSOLE log message is shown - other details like level, category, file and line number are omitted. -config LOG_SYSLOG - bool "Log output to syslog server" - depends on LOG && NET - help - Enables a log driver which broadcasts log records via UDP port 514 - to syslog servers. - -config LOG_TEST - bool "Provide a test for logging" - depends on LOG && UNIT_TEST - default y if SANDBOX - help - This enables a 'log test' command to test logging. It is normally - executed from a pytest and simply outputs logging information - in various different ways to test that the logging system works - correctly with various settings. +endif config LOG_ERROR_RETURN bool "Log all functions which return an error" - depends on LOG help When an error is returned in U-Boot it is sometimes difficult to figure out the root cause. For example, reading from SPI flash may @@ -805,6 +804,18 @@ config LOG_ERROR_RETURN You can add log_ret() to all functions which return an error code. +config LOG_TEST + bool "Provide a test for logging" + depends on UNIT_TEST + default y if SANDBOX + help + This enables a 'log test' command to test logging. It is normally + executed from a pytest and simply outputs logging information + in various different ways to test that the logging system works + correctly with various settings. + +endif + endmenu config SUPPORT_RAW_INITRD |