summaryrefslogtreecommitdiff
path: root/post/board/lwmon5/watchdog.c
diff options
context:
space:
mode:
Diffstat (limited to 'post/board/lwmon5/watchdog.c')
-rw-r--r--post/board/lwmon5/watchdog.c121
1 files changed, 0 insertions, 121 deletions
diff --git a/post/board/lwmon5/watchdog.c b/post/board/lwmon5/watchdog.c
deleted file mode 100644
index 1332da21d0..0000000000
--- a/post/board/lwmon5/watchdog.c
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * (C) Copyright 2008 Dmitry Rakhchev, EmCraft Systems, rda@emcraft.com
- *
- * Developed for DENX Software Engineering GmbH
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-
-/* This test verifies if the reason of last reset was an abnormal voltage
- * condition, than it performs watchdog test, measuing time required to
- * trigger watchdog reset.
- */
-
-#include <post.h>
-
-#if CONFIG_POST & CONFIG_SYS_POST_WATCHDOG
-
-#include <watchdog.h>
-#include <asm/ppc4xx-gpio.h>
-#include <asm/io.h>
-
-static uint watchdog_magic_read(void)
-{
- return in_be32((void *)CONFIG_SYS_WATCHDOG_FLAGS_ADDR) &
- CONFIG_SYS_WATCHDOG_MAGIC_MASK;
-}
-
-static void watchdog_magic_write(uint value)
-{
- out_be32((void *)CONFIG_SYS_WATCHDOG_FLAGS_ADDR, value |
- (in_be32((void *)CONFIG_SYS_WATCHDOG_FLAGS_ADDR) &
- ~CONFIG_SYS_WATCHDOG_MAGIC_MASK));
-}
-
-int sysmon1_post_test(int flags)
-{
- if (gpio_read_in_bit(CONFIG_SYS_GPIO_SYSMON_STATUS) == 0) {
- /*
- * 3.1. GPIO62 is low
- * Assuming system voltage failure.
- */
- post_log("sysmon1 Abnormal voltage detected (GPIO62)\n");
- post_log("POST sysmon1 FAILED\n");
- return 1;
- } else {
- post_log("sysmon1 PASSED\n");
- }
-
- return 0;
-}
-
-int lwmon5_watchdog_post_test(int flags)
-{
- /* On each reset scratch register 1 should be tested,
- * but first test GPIO62:
- */
- if (!(flags & POST_MANUAL) && sysmon1_post_test(flags)) {
- /* 3.1. GPIO62 is low
- * Assuming system voltage failure.
- */
- /* 3.1.1. Set scratch register 1 to 0x0000xxxx */
- watchdog_magic_write(0);
- /* 3.1.2. Mark test as failed due to voltage?! */
- return 1;
- }
-
- if (watchdog_magic_read() != CONFIG_SYS_WATCHDOG_MAGIC) {
- /* 3.2. Scratch register 1 differs from magic value 0x1248xxxx
- * Assuming PowerOn
- */
- int ints;
- ulong base;
- ulong time;
-
- /* 3.2.1. Set magic value to scratch register */
- watchdog_magic_write(CONFIG_SYS_WATCHDOG_MAGIC);
-
- ints = disable_interrupts ();
- /* 3.2.2. strobe watchdog once */
- WATCHDOG_RESET();
- out_be32((void *)CONFIG_SYS_WATCHDOG_TIME_ADDR, 0);
- /* 3.2.3. save time of strobe in scratch register 2 */
- base = post_time_ms (0);
-
- /* 3.2.4. Wait for 150 ms (enough for reset to happen) */
- while ((time = post_time_ms (base)) < 150)
- out_be32((void *)CONFIG_SYS_WATCHDOG_TIME_ADDR, time);
- if (ints)
- enable_interrupts ();
-
- /* 3.2.5. Reset didn't happen. - Set 0x0000xxxx
- * into scratch register 1
- */
- watchdog_magic_write(0);
- /* 3.2.6. Mark test as failed. */
- post_log("hw watchdog time : %u ms, failed ", time);
- return 2;
- } else {
- /* 3.3. Scratch register matches magic value 0x1248xxxx
- * Assume this is watchdog-initiated reset
- */
- ulong time;
- /* 3.3.1. So, the test succeed, save measured time to syslog. */
- time = in_be32((void *)CONFIG_SYS_WATCHDOG_TIME_ADDR);
- if (time > 90 ) { /* ms*/
- post_log("hw watchdog time : %u ms, passed ", time);
- /* 3.3.2. Set scratch register 1 to 0x0000xxxx */
- watchdog_magic_write(0);
- return 0;
- } else {
- /*test minimum watchdogtime */
- post_log("hw watchdog time : %u ms, failed ", time);
- return 2;
- }
- }
- return -1;
-}
-
-#endif /* CONFIG_POST & CONFIG_SYS_POST_WATCHDOG */