Age | Commit message (Collapse) | Author | Files | Lines |
|
Add JH7110_DISTRO_BOOTEN/JH7110_SDK_BOOTEN for debian/sdk boot on JH7110
SOC.
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
These bootenvs do not apply with multiple boots
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
CHIPA_SET_FORCE is for debug and no need any more.
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
CR_6864_515: mmc: starfive: add high speed support
See merge request sbc/u-boot!60
|
|
add high speed support
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
|
|
CR_6806: spl: starfive: modify driver strength and slew rate
See merge request sbc/u-boot!59
|
|
CR_6806: spl: starfive: modify driver strength and slew rate
See merge request sdk/u-boot!63
|
|
The frequency of cclk_in is limited to 50M, so that it does not do internal
part frequency and goes by-pass mode. And delete syscon node.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
Set eMMC/sd clk's DR to 2 and set its SR to 1.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
The frequency of cclk_in is limited to 50M, so that it does not do internal
part frequency and goes by-pass mode. And delete syscon node.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
Set eMMC/sd clk's DR to 2 and set its SR to 1.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
|
|
defconfig: starfive: enable HS200 support
See merge request sbc/u-boot!58
|
|
CR_6728 pci: Get te correct config addr to support multi PCI
See merge request sbc/u-boot!57
|
|
CR_6570: mmc: starfive: add HS200 support
See merge request sdk/u-boot!62
|
|
enable HS200 support.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
SET_DS/SET_PULL/SET_SLEW can configure the properties of the GPIO
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
enable HS200 support.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
CR_6728 pci: Get te correct config addr to support multi PCI
See merge request sdk/u-boot!61
|
|
fix mmc device power-up sequence.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
Add tuning and other related code to the driver to support HS200 mode.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
|
|
Enable pcie0 to active usb-host. And set cdns3 to
device mode.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
|
|
vf2 board using pci-xhci usb host, cdns3 use as devices.
So add this enable vf2 usb-host function.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
|
|
subtract the root bus number to get the correct
config addr.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
|
|
subtract the root bus number to get the correct
config addr.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
|
|
|
|
CR6604: bord: starfivbe: vf2: sync from devkits/sdk
See merge request sbc/u-boot!55
|
|
CR_6648: board: starfive: evb: use dram_init in spl
See merge request sdk/u-boot!60
|
|
dram_init call fdtdec_setup_mem_size_base, so starfive_ddr.c do not
need it.
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
For integration with other Borad, move I2C to a board-level file
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
CR6604:dram: jh7110: sync from devkits/vf2
See merge request sdk/u-boot!59
|
|
'jh7110-master'
CR 6572 uboot: hdmi logo causes kernel hdmi unstable
See merge request sdk/u-boot!58
|
|
Add ddr4 tuning support (sync from devkits)
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
The resize-ddr should be board-level code
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Add board-level resize-DDR function for visionfive 2
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Synchronize from vf2 to the dynamic CMA scheme
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Add ddr4 tuning support (sync from devkits)
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Add board-level resize-DDR function for evb
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
replace mipi&hdmi node , hdmi logo will start begin mipi
Signed-off-by: Keith Zhao <keith.zhao@starfivetech.com>
|
|
The hdmi display is unstable after repeated reset
blank panel or write panel
Signed-off-by: Keith Zhao <keith.zhao@starfivetech.com>
|
|
The resize-ddr should be board-level code
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
|
|
CR6441: borad: starfive: vf2: Adjust the CMA size adaptively
See merge request sbc/u-boot!54
|
|
CR5623: Add 1G DDR support && Simplify the command of uboot to load Linux
See merge request sbc/u-boot!53
|
|
CR5623: Add 1G DDR support && Simplify the command of uboot to load Linux
See merge request sdk/u-boot!57
|
|
Adaptively adjust the CMA size according to the DDR size
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Optimized environment variables for debian boot
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Readjust the address space for 1G DDR
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|
|
Radxa uses macronix spi flash, so enable it.
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
|