summaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-01-27net: fix ping in netconsoleYang Liu1-1/+1
Should not init eth device when doing ping in netconsole. Signed-off-by: Yang Liu <yliu@cybertec.com.au> Cc: Joe Hershberger <joe.hershberger@ni.com>
2021-01-27net: e1000: Add missing address translationsStefan Roese1-5/+5
Add some missing address translations from virtual address in local DRAM to physical address, which is needed for the DMA transactions to work correctly. This issue was detected while testing the e1000 driver on the MIPS Octeon III platform, which needs address translation. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-27net: e1000: Use virt_to_phys() instead of pci_virt_to_mem()Stefan Roese1-7/+1
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual address in local DRAM to a physical address. The correct macro here is virt_to_phys() so switch to using this macro. As virt_to_bus() is now not used any more, this patch also removes both definitions (DM and non-DM). This issue was detected while testing the e1000 driver on the MIPS Octeon III platform, which needs address translation. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-27net: e1000: Remove unused bus_to_phys() macroStefan Roese1-2/+0
bus_to_phys() is defined but not referenced at all. This patch removes it completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Aaron Williams <awilliams@marvell.com> Cc: Chandrakala Chavva <cchavva@marvell.com>
2021-01-26Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini61-423/+4587
- New Allwinner H616 SoC support (sans Ethernet & USB) - H6 DT update - Tanix TX6 TV box support - OrangePi 3 support - OrangePi Zero2 (H616) support
2021-01-26sunxi: Add support for OrangePi Zero2Jernej Skrabec4-0/+262
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0 port. It also has two GPIO headers which allows further peripherals to be used. The devicetree file is taken from v3 of the OrangePi Zero2 Linux submission [1], which it's not yet merged. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26clk: sunxi: Add support for H616 clocksJernej Skrabec3-0/+128
This commit introduces DM H616 clock driver. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: gpio: introduce compatible for H616Jernej Skrabec1-0/+2
H616 pinctrl is no different configuration wise than others, so just add compatible for it. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26arm: sunxi: add initial H616 DTSI and headersJernej Skrabec5-0/+938
This commit introduces H616 DTSI file and dt-bindings headers needed for device tree files. Files are taken from v3 Linux H616 support submission[1], as the H616 .dtsi file is not merged upstream yet. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Add H616 FEL supportJernej Skrabec1-1/+4
H616 uses different address for reset. Add it. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Add support for H616 SoCJernej Skrabec6-1/+35
H616 is very similar to H6 so most of the infrastructure can be reused. However, two big differences are that it doesn't have functional SRAM A2 which is usually used for TF-A and it doesn't have ARISC co-processor. It also needs bigger SPL size - 48 KiB. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26mmc: sunxi: Refactor mod clock register offsetAndre Przywara1-61/+23
So far the only difference between the various Allwinner MMC controller we are concerned about is the mod clock register offset. This is actually not directly related to the MMC controller IP, but an integration choice, dependent on the SoC this appears in. To avoid becoming trapped with some compatible fallback strings, let's remove the whole struct sunxi_mmc_variant, and replace this with a SoC based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols. This will later simplify H616 support. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-26sunxi: Add H616 DRAM supportJernej Skrabec7-0/+1325
Allwinner H616 supports many types of DRAM. Most notably it supports LPDDR4. However, all commercially available boards at this time use only DDR3, so this commit adds only DDR3 support. Controller and MBUS are very similar to H6 but PHY is completely unknown. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: add support for R_I2C on H616Jernej Skrabec2-0/+5
This port is needed for communication with PMIC. SPL uses it to set DRAM voltage on H616 boards. Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: add support for H616 uart0Jernej Skrabec2-0/+5
This port is used for debug terminal on all known H616 boards. Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: introduce support for H616 clocksJernej Skrabec2-3/+23
H616 has mostly the same clocks as H6 with some small differences. Just reuse H6 clocks for H616 and handle differences with macros. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: support loading with SPL > 32KBAndre Przywara2-3/+18
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM driver and need for PMIC configuration, which pulls several drivers which are not needed otherwise. spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with that, reported in SPL header. If size in header is bigger, it will use that value instead. In the process of function rework, also add missing function argument. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org>
2021-01-26sunxi: Add support for I2C on H6 like SoCsJernej Skrabec3-1/+31
I2C support, especially R_I2C port, will be needed in future. Upcoming support for H616 will need R_I2C to adjust DRAM voltage. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: prcm: Add memory map for H6 like SoCsJernej Skrabec3-238/+303
There was no need to have prcm definitions for H6 and similar SoCs till now. However, support R_I2C will be needed soon in SPL. Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h. One of those files will be selected in common prcm.h based on defined macros. This commit doesn't do any functional change. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26i2c: mvtwsi: sunxi: update macroJernej Skrabec1-1/+1
While currently none of the newer Allwinner SoCs currently has I2C support implemented in U-Boot, this will change soon. mvtwsi driver is good as it is for them except one macro. Update it to be ready once I2C support lands for those SoCs. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26mmc: sunxi: Replace H6 ifdefs with H6 gen macroJernej Skrabec2-7/+7
It turns out that several SoCs share same mmc configuration as H6. In order to lower ifdef clutter replace H6 specific macro with common one. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Introduce common symbol for H6 like SoCsJernej Skrabec10-17/+24
It turns out that there are at least 2 other SoCs which have basically the same memory map, similar clocks and other features as H6. It's very likely that we'll see more such SoCs in the future. In order to ease porting to new SoCs and lower ifdef clutter, introduce common symbol for them. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Add support for AXP305 PMICJernej Skrabec7-4/+129
This PMIC can be found on H616 boards and it's very similar to AXP805 and AXP806. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Properly check for SATAPWR and MACPWRAndre Przywara1-12/+22
The #ifdef CONFIG_xxxPWR conditionals were not working as expected, as string Kconfig symbols are always "defined" from the preprocessor's perspective. This lead to unnecessary calls to the GPIO routines, but also always added a half a second delay to wait for a SATA disk to power up. Many thanks to Peter for pointing this out! Fix this by properly comparing the Kconfig symbols against the empty string. strcmp() would be nicer for this, but GCC does not optimise this away, probably due to our standalone compiler switches. Reported-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Samuel Holland <samuel@sholland.org> # Orange Pi WinPlus Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-26sunxi: Add support for Orange Pi 3Andre Heider4-0/+363
dts file is taken from Linux 5.11-rc1 tag. The Bluetooth controller of this device ships with a default address, use the new CONFIG_FIXUP_BDADDR option to fix it up. Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org> [Updated OrangePi 3 DT, rebase and config update] Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26sunxi: Add support for Tanix TX6Jernej Skrabec4-1/+142
This commit adds support for Tanix TX6 TV box, based on H6. It's low end H6 board, with 3 GiB of RAM, eMMC, fast ethernet, USB, IR and other peripherals. DT file is taken from Linux 5.11-rc1 release. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26ARM: dts: sunxi: h6: Update DT filesJernej Skrabec7-73/+794
Updated H6 DT files are based on Linux 5.11-rc1 release. Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-26net: sun8i-emac: Allow all RGMII PHY modesAndre Przywara1-0/+3
So far all GBit users of the sun8i-emac driver were using the "rgmii" PHY mode, even though this turns out to be wrong. It just worked because the PHY driver doesn't do the proper setup (yet). In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the correct ones. To allow the DTs to describe the phy-mode correctly, and to stay compatible with Linux, at least allow those other RGMII modes in the driver. This avoids breakage if mainline DTs will be synced with U-Boot. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25Merge tag 'mips-pull-2021-01-24' of ↵Tom Rini61-72/+4477
https://gitlab.denx.de/u-boot/custodians/u-boot-mips - MIPS: add support for Mediatek MT7620 SoCs
2021-01-25Merge tag 'u-boot-imx-20210125' of ↵Tom Rini90-2347/+10029
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Changes for 2020.04 ------------------- - new board: Phytec phyCORE-i.MX8MP i.MX8MN Beacon EmbeddedWorks devkit - Fixes: several nanbcb fixes fix for imx8mm_beacon - further switch to distro boot commands - DM: DM Ether for MX6UL CI: https://gitlab.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/6013
2021-01-25Merge tag 'doc-2021-04-rc1-2' of ↵Tom Rini15-41/+501
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for documentation tag doc-2021-04-rc1 (2) * Man-pages for sbi, exit, for, echo, loady, true, false, conitrace * Adjust suppression of newline in echo command. * Provide unit test for echo command.
2021-01-25Merge tag 'u-boot-atmel-2021.04-b' of ↵Tom Rini27-30/+436
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel features for 2021.04 cycle This feature set includes macb updates for all interfaces and new sama7g5 variant support; micrel ksz9031 DLL support; a new board from Giant based on Adafruit feather form factor which contains a SAMA5D27 SoC; several fixes regarding the NAND flash PMECC block; and pincontrol drive strength support for pio4 controller.
2021-01-25doc: describe command conitraceHeinrich Schuchardt2-0/+55
Provide a man-page for the conitrace command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25doc: describe the false commandHeinrich Schuchardt2-0/+29
Provide a man-page for the false command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25dm: core: describe uclass_root_sHeinrich Schuchardt1-4/+12
'make htmldocs' creates a warning: ./include/asm-generic/global_data.h:443: warning: Function parameter or member 'uclass_root_s' not described in 'global_data' Correct the member descriptions. Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25doc: document true commandHeinrich Schuchardt2-0/+29
Create a man-page for the true command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25doc: describe loady commandHeinrich Schuchardt2-0/+68
Create a man-page for the loady command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25cmd: correct long text loadb, loadx, loadyHeinrich Schuchardt1-6/+6
The first argument is the load address and not an offset. The second argument cannot be entered without the first one. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-25doc: document echo commandHeinrich Schuchardt2-0/+66
Provide a man-page for the echo command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-25test: unit test for echo commandHeinrich Schuchardt2-0/+60
Provide a unit test for the unit command Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-25cmd: change suppress newline in echo commandHeinrich Schuchardt1-31/+18
By default the echo command emits its arguments followed by a line feed. If any of the arguments contains the sub-string "\c", the line feed is suppressed. This does not match shells used in Linux and BSD where the first argument has to be -n to suppress the line feed. The hush shell interferes with the parsing of backslashes. E.g. in the following command line quadruple backslashes are required for suppressing the line feed: for i in 1 2 3; do for j in 4 5; do echo \\\\c ${i}${j}; done; echo; done; To avoid unexpected behavior the patch changes echo to use -n as first argument to suppress the line feed. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-25doc: document for statementHeinrich Schuchardt2-0/+66
Create a man-page for the for statement. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25doc: describe exit commandHeinrich Schuchardt2-0/+41
Man-page for exit shell command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-25doc: document sbi commandHeinrich Schuchardt3-0/+51
Add a man-page for the sbi command. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-24MAINTAINERS: add maintainer for MediaTek MIPS platformWeijie Gao1-0/+23
Update maintainer for MediaTek MIPS platform Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24reset: reset-mtmips: add DM_FLAG_PRE_RELOC flagWeijie Gao1-0/+1
Add DM_FLAG_PRE_RELOC flag for reset-mtmips to make sure this driver can be probed before relocation even if u-boot,dm-pre-reloc is not present in the dts. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24mmc: mtk-sd: assign plat->cfg.f_max with a correct valueWeijie Gao1-0/+2
Currently this driver does not set the value of plat->cfg.f_max, which results in that MMC framework will always run at the lowest frequency. This patch sets plat->cfg.f_max to the maximum allowed frequency, which equals to the source clock frequency. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24mmc: mtk-sd: add pad control settings for MediaTek MT7620/MT76x8 SoCsWeijie Gao1-3/+118
The driver is missing pad control settings (pad delay and pad conf) for the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will encounter CRC error on data transfers. This patch adds default pad control settings for mt7620_compat. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24mmc: mtk-sd: fix sclk cycles shift valueWeijie Gao1-9/+4
It turns out that the sclk cycles used by mt7620/mt7628 is the same as other chips (20 bits, 1048576), not 65536. This patch removes sclk_cycle_shift from dev_comp, and uses a macro with a value 20 instead. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2021-01-24net: add ethernet driver for MediaTek MT7620 SoCWeijie Gao3-0/+1235
This patch adds ethernet driver for MediaTek MT7620 SoC. The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in 7-port switch and two xMII interfaces (can be MII/RMII/RGMII). The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be configured to connect to either the intergrited FE PHY, or the xMII. Port 5 always connects to the xMII. Port 6 is the CPU port. This driver supports MT7530 giga switch connects to port 5. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-11 15:06:49 +0300