summaryrefslogtreecommitdiff
AgeCommit message (Expand)AuthorFilesLines
2018-02-04imx: mx7: run sec_init for CAAM RNGBryan O'Donoghue1-0/+5
2018-02-04drivers/crypto/fsl: assign job-rings to non-TrustZoneBryan O'Donoghue2-0/+11
2018-02-04i2c: imx: Take mx6dqp in consideration in the I2C_PADS_INFO macroEran Matityahu1-2/+1
2018-02-04iomux-v3: Take mx6dqp in consideration for imx_iomux_v3_setup_pad()Eran Matityahu1-1/+1
2018-02-04doc: mxc_hab: Improve the config option listFabio Estevam1-6/+3
2018-02-04arm: dts: imx6ull: move input include to base device treeStefan Agner2-1/+1
2018-02-04mx6sabresd: Add fastboot supportFabio Estevam1-0/+6
2018-02-04mx6sabresd: Select CONFIG_CMD_USB_MASS_STORAGEFabio Estevam2-1/+1
2018-02-04mx6sabre_common: Allow building CONFIG_USB_FUNCTION_MASS_STORAGEFabio Estevam1-2/+1
2018-02-04board: tbs2910: add private imx configSoeren Moch2-1/+116
2018-02-04imx: mx25: Remove SION bit in all pin-mux that are safeMichael Trimarchi1-281/+290
2018-02-04imx: mx7dsabresd: enable UHS and HS200Peng Fan2-0/+6
2018-02-04mmc: fsl_esdhc: support SDR104 and HS200Peng Fan2-5/+405
2018-02-04ARM: dts: add pinmux and tuning settings for HS200/SDR104Peng Fan1-0/+88
2018-02-04mmc: fsl_esdhc: add strobe and tuning entryPeng Fan1-8/+12
2018-02-04mx6memcal: fix comment in board header fileEric Nelson1-3/+2
2018-02-04mx6memcal: enable SDP supportEric Nelson3-1/+12
2018-02-04mx6memcal: launder through savedefconfigEric Nelson1-5/+4
2018-02-04arm: imx: mx53loco: remove usage of mx53_dram_sizePatrick Bruenn2-39/+1
2018-02-04arm: imx: m53evk: remove usage of mx53_dram_sizePatrick Bruenn2-39/+1
2018-02-04arm: imx: cx9020: move dram init into common placePatrick Bruenn3-35/+48
2018-02-04arm: imx: cx9020: remove usage of mx53_dram_sizePatrick Bruenn1-9/+5
2018-02-04board,ge,bx50v3 - rtc time validationNandor Han3-1/+9
2018-02-04configs: ge_bx50v3: automatic partition selection and video output failure me...Ian Ray1-29/+53
2018-02-04board: ge: bx50v3: mount rootfs read-onlyHannu Lounento1-1/+1
2018-02-04configs: ge_bx50v3: enable bootcountIan Ray1-0/+8
2018-02-04config: ge_bx50v3: read boot scriptIan Ray1-6/+6
2018-02-04board: ge: bx50v3: Support FIT and select configuration based on VPDIan Ray5-83/+20
2018-02-04board: ge: bx50v3: Enable hardware watchdogMartyn Welch2-0/+5
2018-02-04board: ge: bx50v3: program MAC address to I210Hannu Lounento1-1/+36
2018-02-04board: ge: bx50v3: move FEC MAC address programming to driverMartyn Welch2-40/+41
2018-02-04configs: Add network device support for bx50v3 productsIan Ray4-5/+17
2018-02-04board: ge: Enable access to i2c bus 1 and 2Martyn Welch2-2/+4
2018-02-04rtc: adding RX8010SJ rtc driverNandor Han3-0/+385
2018-02-04net: e1000: implement eth_write_hwaddrHannu Lounento1-0/+40
2018-02-04net: e1000: split e1000_read_mac_addrHannu Lounento1-18/+63
2018-02-04net: e1000: add support for writing to EEPROMHannu Lounento2-2/+174
2018-02-04imx: mx8m: add ddr controller memory mapPeng Fan1-0/+356
2018-02-04power: pmic/regulator allow dm be omitted by SPLPeng Fan2-2/+2
2018-02-04imx: imx8mq: add dtsi filePeng Fan4-0/+1765
2018-02-04net: fec: fix build warnings for 64bits supportYe Li1-31/+43
2018-02-04net: fec: do not access reserved register for i.MX8MPeng Fan1-2/+2
2018-02-04gpio: mxc: add i.MX8M supportPeng Fan1-7/+15
2018-02-04imx: lcdif: include i.MX8MPeng Fan1-4/+6
2018-02-04mmc: fsl_esdhc: support i.MX8MPeng Fan1-4/+8
2018-02-04misc: ocotp: add i.MX8M supportPeng Fan1-0/+7
2018-02-04imx: makefile: compile files for i.MX8MPeng Fan1-2/+11
2018-02-04imx: mx8m: add soc related settings and filesPeng Fan7-2/+333
2018-02-04imx: mx7: move mmc env code to mmc_env.cPeng Fan3-21/+31
2018-02-04imx: cpu: support get_boot_device for i.MX8MPeng Fan1-1/+6
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-15 13:32:50 +0300