summaryrefslogtreecommitdiff
path: root/arch/riscv
AgeCommit message (Collapse)AuthorFilesLines
2022-10-18riscv:dts:starfive-jh7110: modify Model and riscv,isa infoyanhong.wang2-6/+6
Change Model to "StarFive JH7110 EVB", and change riscv,isa to "rv64imafdcbsux" Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive:evb: update uart3-uart5 resetsyanhong.wang1-6/+12
Add SPL_DM_RESET to defconfig, and update uart3-uart5 reset for StarFive JH7110 SoC. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18SPL:starfive-jh7110: Modify the default division factor of sdcard clkyanhong.wang1-0/+4
Modify the default division factor of sdcard clk to 4. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive:evb: add usb init configyanhong.wang1-0/+18
Add usb init config for starfive EVB board. Default set to USB2.0 Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18clk:starfive-jh7110: Update pll0/pll1/pll2 clkyanhong.wang1-18/+0
Remove pll0/pll1/pll2 clk define from jh7110_clk.dts to clk-jh7110.c Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18spl: satrfive: bus_root switch to pll2.samin1-5/+0
High-speed emmc/sdio support Signed-off-by: samin <samin.guo@starfivetech.com>
2022-10-18board:starfive:evb: modify the GPIO configuration for sd moduleyanhong.wang1-0/+5
Modify the GPIO configuration for sd&emmc module, switch the clk of sd&emmc to high frequency Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:dts:starfive-jh7110: Modify sd node configurationyanhong.wang4-38/+7
Modify SD&EMMC node configuration on Starfive EVB board. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18SPL:riscv:starfive-jh7110: Adjust CPU working frequencyyanhong.wang2-1/+18
Adjust CPU working frequency from 1G to 1.25G for starfive EVB board. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:dts:starfive-jh7110: add ethernet-phy delay_chain configyanhong.wang2-4/+17
Add ethernet-phy delay_chain configuration for gmac1 on starfive EVB board. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:starfive-jh7110: clear L2 LIM memoryyanhong.wang1-0/+14
Clear L2 LIM memory on StarFive JH7110, avoid some unexpect exception.
2022-10-18riscv:dts:starfive-jh7110: add ddr device nodeyanhong.wang1-0/+7
Add ddr device node for JH7110. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive: add clk inityanhong.wang1-5/+27
Add clk init for ddr on JH7110 board Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18clk:starfive-jh7110: Update pll0/pll1/pll2 clkyanhong.wang2-3/+22
Add JH7110_GMAC0_GTXC clk register and remove pll0/pll1/pll2 clk define from clk-jh7110.c to jh7110_clk.dts Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18GPIO:Starfive-jh7110: Add macro definitionyanhong.wang1-0/+21
Add macro definition of GPIO Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive: add starfive evb board supportyanhong.wang5-0/+153
Add board support for StarFive EVB. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:dts: update clk&reset propertiesyanhong.wang2-157/+443
Synchronize the kernel dts file Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:dts: update clk&reset propertiesyanhong.wang2-53/+182
Synchronize the kernel dts file Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive: add rtc timer inityanhong.wang1-0/+16
The rtc timer is used early in kernel, but the clk&reset driver is not ready,so some clk&reset init is placed here. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18board:starfive: add starfive visionfive board supportyanhong.wang2-0/+49
Add board support for StarFive VisionFive. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:dts: add jh7110 supportyanhong.wang6-0/+1341
Add dts support for jh7110. The starfive visionfive support is based on jh7110 soc. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18riscv:soc:jh7110: Add support jh7110 soc.yanhong.wang7-0/+180
Add StarFive JH7110 soc to support RISC-V arch Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2022-10-18GPIO:Starfive-jh7110: Add GPIO driver for JH7110yanhong.wang1-0/+53
Support for GPIO controller on starfive JH7110 SoCs. Signed-off-by: yanhong.wang <yanhong.wang@starfivetech.com>
2021-09-07riscv: lib: modify the indentZong Li1-1/+1
We usually use a space in function declaration, rather than a tab. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-07board: sifive: use ccache driver instead of helper functionZong Li8-140/+4
Invokes the common cache_init function to initialize ccache. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-07riscv: lib: implement enable_caches for sifive cacheZong Li3-0/+33
The enable_caches is a generic hook for architecture-implemented, we define this function to enable composable cache of sifive platforms. In sifive_cache, it invokes the generic cache_enable interface of cache uclass to execute the relative implementation in SiFive ccache driver. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-07common: board_r: support enable_caches for RISC-VZong Li1-0/+4
The enable_caches is a generic hook for architecture-implemented, we leverage this function to enable caches for RISC-V Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-07riscv: show code leading to exceptionHeinrich Schuchardt1-0/+33
To make analyzing exceptions easier output the code that leads to it. We already do the same on the ARM platform. Here is an example: => exception ebreak Unhandled exception: Breakpoint EPC: 000000008ff5d50e RA: 000000008ff5d62c TVAL: 0000000000000000 EPC: 000000008020b50e RA: 000000008020b62c reloc adjusted Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002) To disassemble the code we can use the decodecode script: $ echo 'Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002)' | \ CROSS_COMPILE=riscv64-linux-gnu- scripts/decodecode Code: 2785 0693 07a0 dce3 fef6 47a5 d563 00e7 (9002) All code ======== 0: 2785 addiw a5,a5,1 2: 07a00693 li a3,122 6: fef6dce3 bge a3,a5,0xfffffffffffffffe a: 47a5 li a5,9 c: 00e7d563 bge a5,a4,0x16 10:* 9002 ebreak <-- trapping instruction ... Code starting with the faulting instruction =========================================== 0: 9002 ebreak ... As it is not always clear if the first 16 bits are at the start or in the middle of a 32bit instruction it may become necessary to strip the first u16 from the output before calling decodecode to get the correct disassembled code. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Sean Anderson <seanga2@gmail.com>
2021-08-17riscv: cpu: fu740: Fix typo of dateZong Li1-1/+1
Fixed the typo of date of copyright declaration. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-08-14efi_loader: add Linux magic to RISC-V crt0Heinrich Schuchardt1-2/+5
Add the Linux magic to the EFI file header to allow running our test programs with GRUB's linux command. MajorImageVersion = 1 indicates a kernel that can consume the EFI_LOAD_FILE2_PROTOCOL. This allows to dump the GRUB provided intird with our initrddump.efi tool. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-07-28i2c: Rename SPL/TPL_I2C_SUPPORT to I2CSimon Glass1-1/+1
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-21board: sifive: drop stuff related to unmatched revision 1Zong Li4-1501/+1
This patch reverts the following commits: - 4b4159d0f3 ("riscv: dts: add dts for unmatched rev1") - ffe9a394df ("board: sifive: support spl multi-dtb on unmatched board") We won't plan to support unmatched that the revision below 3 in u-boot, so they can be dropped because they might be useless. Changed in v2: - rebase codebase to the latest master branch Signed-off-by: Zong Li <zong.li@sifive.com> Suggested-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-21riscv: booti: do not force relocation if force_reloc is not setVitaly Wool1-1/+6
If force_reloc flag is not set and booti is called for an address ouside RAM (i. e. QSPI NOR flash), we should honor that and not try to force relocation in a bogus fashion. Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-07riscv: dts: add OpenPiton RISC-V board dts supportTianrui Wei1-2/+2
Previous device tree for OpenPiton emits a warning during compilation. This commit fixes the previous warning adds dts to the OpenPiton RISC-V board and added the device tree to MAINTAINER file. Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com> Reported-by: Tom Rini <trini@konsulko.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06riscv: dts: add dts for unmatched rev1Zong Li4-1/+1501
The difference between unmatched rev3 and rev1 is DDR timing, the rev3 uses 1866 MT/s for 16GiB, and rev1 uses 2133 MT/s for 8GiB. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06board: sifive: Add an interface to get PCB revisionZong Li1-0/+15
There are different DDR parameter settings for different board revisions. Add a new interface to get the PCB revision to determine which DT should be selected at runtime. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06riscv: sifive: fu740: Support i2c in splZong Li2-0/+5
Enable SPL_I2C_SUPPORT for fu740, and add 'u-boot,dm-spl' property in i2c node. Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06riscv: sifive: fu740: kconfig: Enable support for Opencores I2C controllerZong Li1-0/+2
Enable the Opencores I2C controller on FU740 Signed-off-by: Zong Li <zong.li@sifive.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-07-06board: riscv: add openpiton-riscv64 SoC supportTianrui Wei3-0/+158
This patch adds openpiton-riscv64 SOC support. In particular, this board supports a standard bootflow through zsbl->u-boot SPL-> opensbi->u-boot proper->Linux. There are separate defconfigs for building u-boot SPL and u-boot proper Signed-off-by: Tianrui Wei <tianrui-wei@outlook.com> Signed-off-by: Jonathan Balkind <jbalkind@ucsb.edu> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-28Merge tag 'v2021.07-rc5' into nextTom Rini4-8/+64
Prepare v2021.07-rc5 # gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT # gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C # gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate] # Conflicts: # configs/am64x_evm_r5_defconfig
2021-06-17k210: dts: Set PLL1 to the same rate as PLL0Sean Anderson1-0/+2
Linux has had some stability issues when using AISRAM with a different frequency from SRAM. Mirror their change here now that we relocate into AISRAM. Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-17riscv: andes_plic: Fix riscv_get_ipi() maskBin Meng1-1/+3
Current logic in riscv_get_ipi() for Andes PLICSW does not look correct. The mask to test IPI pending bits for a hart should be left shifted by (8 * gd->arch.boot_hart), just the same as what is done in riscv_send_ipi(). Fixes: 8b3e97badf97 ("riscv: add functions for reading the IPI status") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com>
2021-06-17riscv: ae350: dts: Add missing "u-boot, dm-spl" for SPL configBin Meng3-0/+54
At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The intention was to use gdb to load device tree before running U-Boot SPL/proper from RAM. When we switch to OF_SEPARATE we will have to use our own DT but without "u-boot,dm-spl" in several essential nodes, SPL does not boot. Let's add all the required "u-boot,dm-spl" for SPL config. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-06-17riscv: ae350: dts: Fix #interrupt-cells for plic0 in 32-bitBin Meng1-1/+1
All the device nodes that refer to plic0 as their interrupt parent have 2 cells encoded in their interrupts property, but plic0 only provides 1 cell in #interrupt-cells which is incorrect. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-17riscv: ae350: dts: Remove the unnecessary #address-cells in plic nodesBin Meng2-4/+0
PLIC nodes don't have child nodes, so #address-cells is not needed. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-17riscv: ae350: dts: Remove the unnecessary space in bootargsBin Meng2-2/+2
There are two spaces before "debug' in bootargs. Drop one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-06-17riscv: ae350: dts: Add SPDX license headerBin Meng2-0/+4
The SPDX license header is currently missing. Add one. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-31riscv: cpu: fu740: clear feature disable CSRGreen Wan1-0/+15
Clear feature disable CSR to turn on all features of hart. The detail is specified at section, 'SiFive Feature Disable CSR', in user manual https://sifive.cdn.prismic.io/sifive/aee0dd4c-d156-496e-a6c4-db0cf54bbe68_sifive_U74MC_rtl_full_20G1.03.00_manual.pdf Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-31board: sifive: add HiFive Unmatched board supportGreen Wan1-0/+4
Add defconfig and board support for HiFive Unmatched. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-05-31riscv: dts: add SiFive Unmatched board supportGreen Wan4-0/+1790
Add dts files for SiFive Unmatched board. Signed-off-by: Green Wan <green.wan@sifive.com> Reviewed-by: Rick Chen <rick@andestech.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-10-06 13:42:33 +0300