Age | Commit message (Collapse) | Author | Files | Lines |
|
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This relies on the old LCD implementation which is to be removed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This relies on the old LCD implementation which is to be removed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The SPI and NAND board variants never went into production.
Drop those board variants.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
Since I'm leaving the company with end of June, the maintainership will
be transferred to Wolfgang Wallner.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
|
|
The board was not converted to DM_VIDEO before deadline, so disable
video support for now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add drivers/video/ti/ folder and move all TI's code in this folder for
better maintenance.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Fix building errors if CONFIG_DM_VIDEO is enabled. This is the only
u-boot board that enables CONFIG_AM335X_LCD and from which I started
to develop the version of the frame buffer driver that supports the
driver model.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
|
|
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Move this function out of common.h and into a relevant header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
These don't need to be in common.h so move them out.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
- More DaVinci updates and fixes
- PCIe support on am65x
- Watchdog converted to DM
- Assorted other bugfixes
|
|
This commit adds support for the B&R brsmarc1 SoM.
The SoM is based on TI's AM335x SoC.
Mainly vxWorks 6.9.4.x is running on the board,
doing some PLC stuff on various carrier boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Move env_get_ulong() over to the new header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Move env_set_ulong() over to the new header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
The handling of regarding bootmode and early setup has been moved to
central location 'common/br_resetc.c', so use this on brxre1 board.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
- fixup coding style
- drop unused 'PUSH_KEY' define
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
On many B&R boards we have a reset-controller, responsible for very
early board-bringup (voltages, clocks, ...) and bootmode selection.
To be ready for adding more B&R boards to source tree while avoiding
duplicate code, we add the resetcontroller implementation to the common
part of B&R boards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Many B&R boards are equipped with an I2C-EEPROM where various
information can be stored.
Today there is only a single byte for 'board_id' used.
We write this 'board_id' into environment for later use during boot.
If the value != 0xFF, meaning the byte is programmed, we modify the
"brdefaultip" environment variable for setting an IP-Address based on
board_id.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Today the BuR common stuff is only used on AM33XX boards. In future we
plan to have many other platforms than AM33XX so we have to move arch-
specific #include(s) to responsible #ifdef sections. By the way we drop
unneeded #include(s).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
This commit converts the brxre1 board to DM,
for this we have todo following things:
- add a devicetree-file for this board
- drop all obsolete settings from board header-file
- use dm_i2c_xxx calls for read/write to the resetcontroller
- request gpios before operate them
Serues-cc: trini@konsulko.com
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
The TPS62517 PMIC driver has been partially converted to DM, so the
legacy I2C access layer isn't needed anymore.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
On other OS, not one provided by B&R, it is not guaranteed that there
are factory-settings within a devicetree. So we must not treat the
absence of them as error.
Further we've the fact that on different version of the device-tree
files there are different namings of the factory-settings, we consider
this with searching for an alternative name.
changing things as following:
- don't treat as error if the bootloader version cannot written into
devicetree.
- since the naming of the factory-settings are different in different
versions of the provided device-tree we search for the alternate name
"/fset"
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
If a board-code calls the pmicsetup(u32 mpupll) with a mpupll value
!= 0 it wants to force some frequency with the value provided by mpupll.
Setting up 1 GHz is wrong here.
Nobody did take notice about that yet, since every board calls this
function with zero.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This interface names may vary over different products, to consider this
fact we replace the interface label "IF1" and "IF2" on the summary
screen with some more generic wording "MAC1" and "MAC2".
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
Since we're going to drop LCD-support on brppt1 boards, we have to make
this stuff here optional and remove the #error path.
We also move out the ft_board_setup(...) from this #ifdef because
there's no relationship with the LCD-code and on the other hand this is
still needed in future even with LCD-support off.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
The linux systems running on the brppt1 targets are using modern DRM
drivers since long time ago. Further we are going to drop the LCD
support completely on this board, so the simple-framebuffer setup
becomes obsolete.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
The clock selection is done now from the am335x-fb code, so there is no
more need doing this in the board code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
Actual am335x-fb implementation takes now a real clock frequency instead
a divider. So this component doesn't need to know anymore some base
frequency of the LCDC, we simply provide the pixel-clock frequency.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|