summaryrefslogtreecommitdiff
path: root/board/freescale
AgeCommit message (Collapse)AuthorFilesLines
2022-02-09imx: Don't define __ASSEMBLY__ in source filesSimon Glass16-16/+0
This is supposed to be a build-system flag. Move it there so we can define it before linux/kconfig.h is included. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-02-05imx8mn-ddr4-evk: generate single bootable imageAndrey Zhizhikin1-1/+1
As suggested in commit 028abfd9b157 ("imx8mm-evk: Generate a single bootable flash.bin again") for imx8mm_evk, it is possible to produce single bootable image via binman. This restores the original behavior in distros, where only one boot container is used to create target image. Perform similar adaptions in order to provide single bootable image for imx8mn-ddr4-evk derivate. Update documentation to drop additional step of copying u-boot.itb Fixes: 353dfe4b4359 ("imx8mn-ddr4-evk: switch to use binman") Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-02-05imx8ulp: Workaround LPOSC_TRIM fuse load issueYe Li1-0/+6
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0 LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision. A0.2 will fix the issue in ROM. But A0.1 we have to workaround it in SPL by setting LPOSCCTRL BIASCURRENT again. Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05imx8ulp: Fix DCNANO QoS settingYe Li1-0/+3
The setting does not have effect because we should set it after power on the PS16 for NIC AV. So move it after upower_init which has powered on all PS Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-05imx8ulp_evk: Control LPI2C0 PCA6416 and TPM0 for displayYe Li1-0/+56
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and backlight. However the LPI2C0 and TPM0 are M33 resources, in this patch we simply access them, but this is a temporary solution. We will modify it when M33 FW changes to set MIPI DSI panel as default path and enable backlight after reset. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-02-01board: ls1046ardb: force PCI device enumerationMartin Schiller1-0/+4
Commit 045ecf899252 ("configs: enable DM_ETH support for LS1046ARDB") resulted in the PCI bus no longer being implicitly enumerated. However, this is necessary for the fdt pcie fixups to work. Therefore, similar to commit 8b6558bd4187 ("board: ls1088ardb: transition to DM_ETH"), pci_init() is now called in the board_init() routine when CONFIG_DM_ETH is active. Signed-off-by: Martin Schiller <ms@dev.tdt.de> CC: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-02-01board: ls1088a: update ifc node name to be memory-controllerJianpeng Bu1-5/+5
IFC-NOR and QSPI are muxed on SoC. So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts in case QSPI is not enabled. "ifc/nor" will be changed to "memory-controller/nor" in linux. So need to modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset(). Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-02-01board: ls1043ardb: force PCI device enumerationMartin Schiller1-0/+4
Commit eb1986804d1d ("configs: enable DM_ETH support for LS1043ARDB") resulted in the PCI bus no longer being implicitly enumerated. However, this is necessary for the fdt pcie fixups to work. Therefore, similar to commit 8b6558bd4187 ("board: ls1088ardb: transition to DM_ETH"), pci_init() is now called in the board_init() routine when CONFIG_DM_ETH is active. Signed-off-by: Martin Schiller <ms@dev.tdt.de> CC: Priyanka Jain <priyanka.jain@nxp.com> CC: Camelia Groza <camelia.groza@nxp.com> Acked-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-01-20fdt_support: Add fdt_for_each_node_by_compatible() helper macroMarek Behún1-4/+1
Add macro fdt_for_each_node_by_compatible() to allow iterating over fdt nodes by compatible string. Convert various usages of off = fdt_node_offset_by_compatible(fdt, start, compat); while (off > 0) { code(); off = fdt_node_offset_by_compatible(fdt, off, compat); } and similar, to fdt_for_each_node_by_compatible(off, fdt, start, compat) code(); Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-01-18common: board_r: move init_addr_map() to init.hOvidiu Panait1-4/+1
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because the header is only present on arm and powerpc. In order to remove the dependency on this header and the associated ifdef, move init_addr_map() declaration to init.h, since it is only called during the common init sequence. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
2021-12-28Finish conversion of CONFIG_SYS_CLK_FREQ to KconfigTom Rini17-9/+19
In order to finish moving this symbol to Kconfig for all platforms, we need to do a few more things. First, for all platforms that define this to a function, introduce CONFIG_DYNAMIC_SYS_CLK_FREQ, similar to CONFIG_DYNAMIC_DDR_CLK_FREQ and populate clock_legacy.h. This entails also switching all users from CONFIG_SYS_CLK_FREQ to get_board_sys_clk() and updating a few preprocessor tests. With that done, all platforms that define a value here can be converted to Kconfig, and a fall-back of zero is sufficiently safe to use (and what is used today in cases where code may or may not have this available). Make sure that code which calls this function includes <clock_legacy.h> to get the prototype. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-28CONFIG_SYS_CLK_FREQ: Consistently be static or get_board_sys_clk()Tom Rini11-37/+11
This CONFIG option is used in one of two ways. The first way is that it is defined to a static value, of an unsigned long size. The second way is that it is defined to something, typically a function, to determine this value at run time. However, in a few cases that function returns a static value. Change that to using the static value directly. In the case of using something at run time, convert everything to using a function of the same name and prototype. This will allow for further cleanups. Finally, we have a few cases where the function is just not used, so drop it. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-28nxp: ics307_clk: Guard get_board_ddr_clk function correctlyTom Rini1-0/+2
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should have this function, so guard it so that we can include <clock_legacy.h> in this file later on. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-28ls1088a: Guard get_board_ddr_clk function correctlyTom Rini1-0/+2
When we have CONFIG_DYNAMIC_DDR_CLK_FREQ set is the only time we should have this function, so guard it so that we can include <clock_legacy.h> in this file later on. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27Finish CONFIG_VID et al conversion to KconfigTom Rini2-6/+37
This converts the following to Kconfig: CONFIG_VID CONFIG_VOL_MONITOR_INA220 CONFIG_VOL_MONITOR_IR36021_READ CONFIG_VOL_MONITOR_IR36021_SET CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET To finish this migration, we first need to introduce CONFIG_SPL_VID as some platforms only use this code in full U-Boot while others use it in SPL as well. To make the Kconfig logic clearer, guard all of the sub-options with a if VID || SPL_VID check. Finally, add Kconfig options for the remaining related options that did not previously have one. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-19fdt_support: Remove fdt_alloc_phandle() in favor of fdt_generate_phandle()Marek Behún2-4/+12
Commit f0921f5098d ("fdt: Sync up to the latest libfdt") introduced fdt_generate_phandle() in libfdt, making fdt_alloc_phandle() obsolete in fdt_support. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: "hui.song" <hui.song_1@nxp.com> Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-11-09board: freescale: lx216x : increase fdt blob sizeWasim Khan1-0/+8
Increase fdt blob size for lx2160 and lx2162 series to fix below errors/warnings during device tree fixup. Unable to update property /soc/spi@2100000:status, err=FDT_ERR_NOSPACE Unable to update property /soc/spi@2110000:status, err=FDT_ERR_NOSPACE Unable to update property /soc/spi@2120000:status, err=FDT_ERR_NOSPACE WARNING: could not set reg FDT_ERR_NOSPACE. WARNING unable to set iommus: FDT_ERR_NOSPACE Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-11-09board: fsl_validate: Fix Double free IssueKshitiz Varshney1-22/+6
Remove Double free issue from calc_img_key_hash() and calc_esbchdr_esbc_hash() function. Verified the secure boot changes using lx2162aqds board. Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-11-09board: freescale: t104xrdb: Set popts->cpo_sample to 0x54 for DDR3Priyanka Singh1-0/+2
Set popts->cpo_sample to 0x54 in t104xrdb/ddr.c to optimize cpo Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-10-31board: freescale: various boards: Let env subsystem set gd->env_addrMarek Behún8-29/+0
Various freescale boards set gd->env_addr to default_environment in board_init(), conditional on CONFIG_ENV_IS_NOWHERE, but this is redundant, since it is done by env_init() before board_init() is called. Let the env subsystem handle this. Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Ramon Fried <rfried.dev@gmail.com> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Mian Yousaf Kaukab <ykaukab@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-21imx8mp_evk: Remove EQoS PHY reset codesYe Li1-19/+0
Since we uses the DTS and PHY reset gpio in EQoS driver to do the reset, remove the duplicated codes from board file. Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-21imx8mp_evk: Fix incorrect cascade for FEC and EQOS setupYe Li1-2/+3
The setup functions should be independent for two ethernet controllers Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-20imx8mm-evk: Generate a single bootable flash.bin againFabio Estevam1-1/+1
After the conversion to binman in commit 8996e6b7c6a1 ("imx8mm_evk: switch to use binman to pack images"), it is necessary to flash both flash.bin and u-boot.itb to get a bootable system. Prior to this commit, only flash.bin was needed. Such new requirement breaks existing distro mechanisms to generate the final binary because the extra u-boot.itb is now required. Generate a final flash.bin that can be used again as a single bootable binary to keep the original behavior. After this change the SPL binary is called spl.bin, which is a more descriptive name for its purpose, and can still be used standalone (for example, for secure boot purposes). Also update imx8mm_evk.rst to remove the u-boot.itb copy step. Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
2021-10-07arm: dts: imx8mp: Generate single bootable binaryTeresa Remmet1-1/+1
binman conversion made flashing flash.bin and u-boot.itb necessary. Update binman config to create a single flash.bin image again. This updates imx8mp_evk and phyCORE-i.MX8MP as they share the same binman config. Updated also imx8mp_evk documentation. Tested on phyCORE-i.MX8MP. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-10-06nand.h: Cleanup linux/mtd/rawnand.h usageTom Rini2-0/+2
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward declaration of struct nand_chip, so do that directly. Then, include <linux/mtd/rawnand.h> where required directly. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-02ppc: Remove MPC8349EMDS board and ARCH_MPC8349 supportTom Rini6-537/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-30WS cleanup: remove SPACE(s) followed by TABWolfgang Denk7-16/+16
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30WS cleanup: remove trailing white spaceWolfgang Denk1-1/+1
Signed-off-by: Wolfgang Denk <wd@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-09-30WS cleanup: remove excessive empty linesWolfgang Denk2-3/+0
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-30WS cleanup: remove trailing empty linesWolfgang Denk7-7/+0
Signed-off-by: Wolfgang Denk <wd@denx.de>
2021-09-29Merge branch 'network_master' of ↵Tom Rini25-71/+70
https://source.denx.de/u-boot/custodians/u-boot-net into next - Fix some non-NULL terminated strings in the networking subsystem - net: tsec: Mark tsec_get_interface as __maybe_unused
2021-09-28net: freescale: replace usage of phy-mode = "sgmii-2500" with "2500base-x"Vladimir Oltean7-16/+16
After the discussion here: https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/ which resulted in this patch: https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/ and many other discussions before it, notably: https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/ it became apparent that nobody really knows what "SGMII 2500" is. Certainly, Freescale/NXP hardware engineers name this protocol "SGMII 2500" in the reference manuals, but the PCS devices do not support any "SGMII" specific features when operating at the speed of 2500 Mbps, no in-band autoneg and no speed change via symbol replication . So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without in-band autoneg and at a fixed speed" is indistinguishable from "2500base-x without in-band autoneg", which is precisely what these NXP devices support. So it just appears that "SGMII 2500" is an unclear name with no clear definition that stuck. As such, in the Linux kernel, the drivers which use this SERDES protocol use the 2500base-x phy-mode. This patch converts U-Boot to use 2500base-x too, or at least, as much as it can. Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500 completely, but the mvpp2 driver seems to even distinguish between SGMII 2500 and 2500base-X. Namely, it enables in-band autoneg for one but not the other, and forces flow control for one but not the other. This goes back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500 is an MII protocol (connects a MAC to a PHY such as Aquantia), but the two are practically indistinguishable through everything except use case. NXP devices can support both use cases through an identical configuration, for example RX flow control can be unconditionally enabled in order to support rate adaptation performed by an Aquantia PHY. At least I can find no indication in online documents published by Cisco which would point towards "SGMII-2500" being an actual standard with an actual definition, so I cannot say "yes, NXP devices support it". Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28net: replace the "xfi" phy-mode with "10gbase-r"Vladimir Oltean20-54/+53
As part of the effort of making U-Boot work with the same device tree as Linux, there is an issue with the "xfi" phy-mode. To be precise, in Linux there was a discussion (for those who have time to read: https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/) which led to a patch: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881 TL;DR: "xfi" was standardized in Linux as "10gbase-r". This patch changes the relevant occurrences in U-Boot to use "10gbase-r" instead of "xfi" wherever applicable. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-28net: update NXP copyright textVladimir Oltean1-1/+1
NXP Legal insists that the following are not fine: - Saying "NXP Semiconductors" instead of "NXP", since the company's registered name is "NXP" - Putting a "(c)" sign in the copyright string - Putting a comma in the copyright string The only accepted copyright string format is "Copyright <year-range> NXP". This patch changes the copyright headers in the networking files that were sent by me, or derived from code sent by me. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
2021-09-16Merge tag 'v2021.10-rc4' into nextTom Rini1-0/+1
Prepare v2021.10-rc4 Signed-off-by: Tom Rini <trini@konsulko.com> # gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT # gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C # gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate] # Conflicts: # board/Arcturus/ucp1020/spl.c # cmd/mvebu/Kconfig # common/Kconfig.boot # common/image-fit.c # configs/UCP1020_defconfig # configs/sifive_unmatched_defconfig # drivers/pci/Kconfig # include/configs/UCP1020.h # include/configs/sifive-unmatched.h # lib/Makefile # scripts/config_whitelist.txt
2021-09-08common/spl: Drop [ST]PL_HASH_SUPPORT in favor of [ST]PL_HASHAlexandru Gagniuc1-0/+1
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for CHAIN_OF_TRUST to select SPL_HASH now. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> [trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07arm: Disable ATAGs supportTom Rini5-10/+6
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and stemmy, disable ATAG support. A large number of platforms had enabled support but never supported a kernel so old as to require it. Further, some platforms are old enough to support both, but are well supported by devicetree booting, and have been for a number of years. This is because some of the ATAGs related functions have been re-used to provide the same kind of information, but for devicetree or just generally to inform the user. When needed still, rename these functions to get_board_revision() instead, to avoid conflicts. In other cases, these functions were simply unused, so drop them. Cc: Andre Przywara <andre.przywara@arm.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Phil Sutter <phil@nwl.cc> Cc: Stefan Bosch <stefan_b@posteo.net> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-04i2c: Convert CONFIG_POWER_I2C et al to KconfigSimon Glass2-2/+2
This converts the following to Kconfig: CONFIG_POWER_I2C CONFIG_POWER_LEGACY They are handled at the same time due to a dependency between them. Update the Makefile rule to use legacy power only in U-Boot proper. Unfortunately a separate rule is needed in SPL to be able to build legacy power. Add SPL related symbols for both, to allow for SPL-only usage. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> [trini: More SPL related cleanups, reword commit message] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-04power: Rename CONFIG_POWER to CONFIG_POWER_LEGACYSimon Glass2-2/+2
This option is used in pre-driver model code and much of it has never been converted to driver model. We want to add a new option to enable power support, so we can use a simple rule in the Makefile. Rename this one, which is really about a particular implementation of power. Also update the pmic.h header file so it either includes the legacy API or the driver model one. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-09-01Kconfig: Remove all default n/no optionsMichal Simek5-6/+0
default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini2-6/+4
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01imx: Finish migration of IMX_CONFIG to KconfigTom Rini17-1/+52
- Provide a default Kconfig value of the default script - Largely continue to define this via the board Kconfig file - For the boards that select a script based on defconfig rather than TARGET, keep this within the defconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01nxp: Migrate CONFIG_DDR_CLK_FREQ to KconfigTom Rini8-31/+2
As this symbol can either be a fixed value or the function get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ to that value and now include/clock_legacy.h contains the function prototype or defines get_board_ddr_clk() to that static value. Update callers to test for DYNAMIC or STATIC. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31global: Remove unused or unnecessary CONFIG symbols related to DDRTom Rini1-23/+0
These symbols are now either unused or were only used within the config file to determine other logic, which could be done in a way that doesn't further pollute the CONFIG namespace. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Kconfig: Use spaces not tabs in Kconfig entiresTom Rini1-2/+2
While the Kconfig language seems to accept either form of whitespace, we use a space throughout the project, except in these spots. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30global: Remove dead code that starts with CONFIG_[0-9A]Tom Rini1-2/+0
This removes a number of spots of dead code based on symbols that start with CONFIG_[0-9] or CONFIG_A. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30i2c: fsl_i2c: Migrate to KconfigTom Rini1-1/+1
- As there are no boards that use different values for speed / slave on different buses, use a single option. - Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options. - Introduce _HAS_ options for additional buses as only the first one is common to all users. - Convert all remaining symbols to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_EARLY_INIT to KconfigTom Rini6-14/+6
Convert SYS_I2C_EARLY_INIT to Kconfig, and make it depend on SPL_SYS_I2C_LEGACY. Remove the weak implementation as it's either something that needs to exist for real, or shouldn't be called. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini1-1/+1
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-18board: T4240rdb: Extend cs4340_get_fw_addr() functionalityKuldeep Singh2-0/+22
T4240RDB supports booting from 2 nor banks(default and altbank). The corresponding defconfig can only have one entry defined and therefore, extend cs4340_get_fw_addr() function to overwrite firmware address which will be later used in cortina firmware. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-19 07:16:45 +0300