summaryrefslogtreecommitdiff
path: root/board/liebherr
AgeCommit message (Collapse)AuthorFilesLines
2021-03-02reset: Remove addr parameter from reset_cpu()Harald Seiler1-1/+1
Historically, the reset_cpu() function had an `addr` parameter which was meant to pass in an address of the reset vector location, where the CPU should reset to. This feature is no longer used anywhere in U-Boot as all reset_cpu() implementations now ignore the passed value. Generic code has been added which always calls reset_cpu() with `0` which means this feature can no longer be used easily anyway. Over time, many implementations seem to have "misunderstood" the existence of this parameter as a way to customize/parameterize the reset (e.g. COLD vs WARM resets). As this is not properly supported, the code will almost always not do what it is intended to (because all call-sites just call reset_cpu() with 0). To avoid confusion and to clean up the codebase from unused left-overs of the past, remove the `addr` parameter entirely. Code which intends to support different kinds of resets should be rewritten as a sysreset driver instead. This transformation was done with the following coccinelle patch: @@ expression argvalue; @@ - reset_cpu(argvalue) + reset_cpu() @@ identifier argname; type argtype; @@ - reset_cpu(argtype argname) + reset_cpu(void) { ... } Signed-off-by: Harald Seiler <hws@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-02common: Drop asm/global_data.h from common headerSimon Glass4-0/+4
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-08xea: spl: Disable pull UP for GPIO0_2{35}Lukasz Majewski1-1/+1
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be enabled. To get the same behavior for both boot select pins (i.e. GPIO0_2{35}) disable pull UPs on both. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-08-04liebherr: Drop duplicate dm.h inclusionSimon Glass1-1/+0
We only need to include this header once. Drop the duplicate. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-17treewide: convert bd_t to struct bd_info by coccinelleMasahiro Yamada4-4/+4
The Linux coding style guide (Documentation/process/coding-style.rst) clearly says: It's a **mistake** to use typedef for structures and pointers. Besides, using typedef for structures is annoying when you try to make headers self-contained. Let's say you have the following function declaration in a header: void foo(bd_t *bd); This is not self-contained since bd_t is not defined. To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h> #include <asm/u-boot.h> void foo(bd_t *bd); Then, the include direcective pulls in more bloat needlessly. If you use 'struct bd_info' instead, it is enough to put a forward declaration as follows: struct bd_info; void foo(struct bd_info *bd); Right, typedef'ing bd_t is a mistake. I used coccinelle to generate this commit. The semantic patch that makes this change is as follows: <smpl> @@ typedef bd_t; @@ -bd_t +struct bd_info </smpl> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-07-16arm: Add extra boot device (UART) to run Ymodem u-boot.img boot on XEA (imx28)Lukasz Majewski1-0/+1
This commit enables imx28 based XEA board's u-boot.sb (SPL) to download u-boot proper (u-boot.img) via Ymodem protocol. This is extremely useful in the recovery scenario where u-boot.sb is downloaded via uuu utility to SDRAM [*], and then one can upload u-boot proper via serial console to fully debrick the device. Note - debricking procedure of imx28 devices: - NXP's original USB based tools (like mxsldr or uuu) expect single u-boot.sb which is a relic of the old U-Boot (~2013) without SPL and U-Boot proper distinction. [*] On Host: ------------ cat << EOF > imx28_xea.lst uuu_version 1.3.0 SDPS: boot -f /srv/tftp/xea/u-boot.sb SDPU: done EOF Please start picocom: sudo picocom -b 115200 -s "sz -vv" /dev/ttyUSB1 sudo ./uuu/uuu -V imx28_xea.lst On the U-boot console one shall see: Trying to boot from UART CCC Then please press CTRL+A, S and type u-boot.img Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-05-19common: Drop linux/delay.h from common headerSimon Glass4-0/+4
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-19common: Drop log.h from common headerSimon Glass3-0/+3
Move this header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-19common: Drop init.h from common headerSimon Glass4-0/+4
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-19common: Drop image.h from common headerSimon Glass4-0/+4
Move this uncommon header out of the common header. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-19common: Drop net.h from common headerSimon Glass1-0/+1
Move this header out of the common header. Network support is used in quite a few places but it still does not warrant blanket inclusion. Note that this net.h header itself has quite a lot in it. It could be split into the driver-mode support, functions, structures, checksumming, etc. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-02-09arm: xea: spl: Add GPIO0_0 setup on spl_board_initLukasz Majewski1-1/+16
Explicitly configure GPIO0_0 in SPL, which controlls 3V3 voltage on the XEA board (it also supplies TIVAs). This code would enable TIVAs power supply early (also when board uses the falcon boot). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-02-09arm: xea: Provide function to set L2 switch 'local-mac-address' propertyLukasz Majewski1-0/+32
The 'local-mac-address' property needs to be adjusted to the MAC address value stored in U-Boot's 'ethaddr' env variable. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-01-17common: Move reset_cpu() to the CPU headerSimon Glass1-0/+1
Move this function out of common.h and into a relevant header file. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-07imx: Add support for i.MX28 based XEA boardLukasz Majewski6-0/+561
This patch introduces support for i.MX28 based XEA board. This board supports DM/DTS in U-Boot proper as well as DM aware drivers in SPL (u-boot.sb) by using OF_PLATDATA. More detailed information regarding usage of it can be found in ./board/liebherr/xea/README file. U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) Trying to boot from MMC1 MMC0: Command 8 timeout (status 0xf0344020) mmc_load_image_raw_sector: mmc block read error U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200) CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SPI #3, master, 3V3 NOR Model: Liebherr (LWE) XEA i.MX28 Board DRAM: 128 MiB MMC: MXS MMC: 0 Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB OK In: serial Out: serial Err: serial Net: Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2 eth0: ethernet@800f0000 Hit any key to stop autoboot: 0 Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-12-03common: Move some board functions out of common.hSimon Glass1-0/+1
A number of board function belong in init.h with the others. Move them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-03common: Move serial functions out of common.hSimon Glass3-0/+3
These functions belong in serial.h so move them over. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-11-03ARM: imx: Convert mccmon6 to use fitImage instead of uImage+DTBLukasz Majewski1-0/+7
This commit enabled support for fitImage on mccmon6 when we switch to DT/DTS (including falcon mode). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Decouple mccmon6's SPL and u-boot proper codeLukasz Majewski3-290/+276
The mccmon6 has been used a "mixed" approach between SPL and U-Boot proper sources. This commit decoupes SPL and u-boot proper, which allows clear distinction between those two code bases and facilitates conversion to DM/DTS on this particular board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-11-03ARM: imx: Convert mccmon6 to use DM/DTS in the u-boot properLukasz Majewski1-161/+0
This commit converts mccmon6's u-boot proper (in a single commit to avoid build breaks) to use solely DM/DTS. The DTS description of the mccmon6 has been ported from Linux kernel (v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08imx: Rewrite display5 get_board_id() function to use dm_gpio_* APILukasz Majewski1-32/+21
The get_board_id() function was using the old gpio_* compatibility layer to read HW and SW ID numbers encoded on the PCB board. After this change the new dm_gpio* API is used for this purpose. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08imx: Convert emergency pad of display5 to use dm_gpio* functionsLukasz Majewski1-5/+7
After this change the display5's emergency gpio use dm_gpio* functions instead of legacy ones (gpio*) to read its state. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: display5: Remove common.c file (after DM/DTS U-Boot proper conversion)Lukasz Majewski4-90/+76
The common.c file content can be safely moved to spl.c file after performing the DM/DTS conversion for the U-Boot proper. It contains the non DM/DTS setup code, which now is only used by SPL. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08ARM: display5: Remove UART initialization code after DM/DTS conversion ↵Lukasz Majewski3-16/+0
(non-console) This UART is not used in U-Boot, so there is no need to initialize it. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)Lukasz Majewski3-44/+12
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not supported as of time of this conversion. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: eth: Switch display5 board to use DM_ETHLukasz Majewski1-104/+30
After this commit the display5 device would use FEC driver supporting driver model (DM_ETH). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: mmc: Switch display5 board to use DM_MMC and BLK (USDHC)Lukasz Majewski3-29/+0
After this commit the display5 device would use eMMC driver supporting driver model (DM_MMC and BLK). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08DM: I2C: Switch display5 board to use DM_I2CLukasz Majewski1-48/+0
After this commit the display5 device would use I2C driver supporting driver model (DM_I2C). The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize on-bus devices according to device tree description. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-08-11env: Drop environment.h header file where not neededSimon Glass2-2/+0
This header file is now only used by files that access internal environment features. Drop it from various places where it is not needed. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11env: Move env_set() to env.hSimon Glass1-0/+1
Move env_set() over to the new header file. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11env: Move env_init() to env.hSimon Glass1-0/+1
Move env_init() over to the new header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11env: Move env_get_f() to env.hSimon Glass1-0/+1
Move this function over to the new header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-19ARM: display5: Remove U_BOOT_DEVICE definition of serial_mxcLukasz Majewski1-9/+0
Before the wide DM/DTS adoption in the U-Boot proper, the display5 has been using only DM_SERIAL to provide serial console in pre-relocation. After moving to full DM/DTS adoption in the U-Boot proper the U_BOOT_DEVICE definition is not needed anymore, as it has been replaced with udevice creation from provided DTS description. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-19ARM: display5: Fix CS check after moving some SPI related CONFIGs to KconfigLukasz Majewski1-1/+1
After commit 14453fbfadc2 ("Convert CONFIG_SF_DEFAULT_* to Kconfig") and commit abe66b1b5dec ("Convert CONFIG_ENV_SPI_* to Kconfig") ,which moved some SPI related CONFIG_* defines to Kconfig the display5 board has become unbootable as the SPI CS check condition had wrong value. This commit fixes this check and allows proper SPI NOR flash operation in SPL. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-06-23Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu5-7/+7
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2018-06-18display5: Add missing environment.h include to avoid warningLukasz Majewski1-0/+1
Without this change the following warning shows up when building: board/liebherr/display5/display5.c:270:3: warning: implicit declaration of function ‘eth_env_set_enetaddr’ [-Wimplicit-function-declaration] This commit fixes this issue. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: net: Add function to read ethaddr from iMX6 fusesLukasz Majewski1-0/+21
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: ddr: Enable support for DDR3 auto calibrationLukasz Majewski1-0/+47
This code performs DDR3 memory calibration for display5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: wdt: Enable WDT support (both SPL and u-boot)Lukasz Majewski1-0/+5
Test case: The fitImage gets corrupted: truncate -c -s 3M fitImage run tftp_mmc_fitImg setenv boot_os y reset [board shall hang in SPL with "Trying to boot from MMC1" information] Then after X seconds WDT is causing board to reset. After N boot attempts we enter recovery mode. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: Support for the emergency PAD pressingLukasz Majewski4-0/+52
To enter the special mode, one needs to short cut two pads with e.g. screw driver. After power up the SPL will execute u-boot in which proper actions will be taken. It is worth noting that we do not alter envs (even the BOOT_FROM variable) and unconditionally go to recovery. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-06-18display5: spl: Check return code of the env_* functionsLukasz Majewski1-2/+2
Force booting through u-boot proper when environment error encountered (as a result of either broken SPI-NOR or erased envs). Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-05-11bootcount: display5: spl: Extend DISPLAY5 board SPL to support bootcount ↵Lukasz Majewski1-1/+2
checking This patch is necessary for providing basic bootcount checking in the case of using "falcon" boot mode in that board. It forces u-boot proper boot, when we exceed the number of errors. Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini9-18/+9
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTRTom Rini1-2/+0
We have a large number of places where while we historically referenced gd in the code we no longer do, as well as cases where the code added that line "just in case" during development and never dropped it. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-05libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>Masahiro Yamada1-1/+1
Thomas reported U-Boot failed to build host tools if libfdt-devel package is installed because tools include libfdt headers from /usr/include/ instead of using internal ones. This commit moves the header code: include/libfdt.h -> include/linux/libfdt.h include/libfdt_env.h -> include/linux/libfdt_env.h and replaces include directives: #include <libfdt.h> -> #include <linux/libfdt.h> #include <libfdt_env.h> -> #include <linux/libfdt_env.h> Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-09imx:display5: Add support for LWN's DISPLAY5 boardLukasz Majewski7-0/+820
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-09-18imx6: drop duplicated bss memset and board_init_r() callAnatolij Gustschin1-6/+0
bss section is cleared in crt0.S. board_init_r() is also entered from crt0 code. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <lukma@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28imx: imx6: Move gpr_init() function to soc.cBreno Lima1-11/+0
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D, MX6Q and MX6QP processors move it to the soc.c file. Signed-off-by: Breno Lima <breno.lima@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-16env: Rename getenv/_f() to env_get()Simon Glass1-2/+2
We are now using an env_ prefix for environment functions. Rename these two functions for consistency. Also add function comments in common.h. Quite a few places use getenv() in a condition context, provoking a warning from checkpatch. These are fixed up in this patch also. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16env: Rename setenv() to env_set()Simon Glass1-1/+1
We are now using an env_ prefix for environment functions. Rename setenv() for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 11:06:52 +0300