summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)AuthorFilesLines
2021-01-15Merge branch '2021.04-rc' of https://github.com/lftan/u-bootTom Rini2-0/+2
- Add ATF flow for SoC64 devices - Update socfpgaimage to support print header and update padding flow
2021-01-13Merge tag 'u-boot-stm32-20210113' of ↵Tom Rini19-130/+153
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Enable logging features for stm32mp15 boards - Update MAINTAINERS emails for STI and STM32 - Activate OF_LIVE for ST stm32mp15 boards - Switch to MCO2 for PHY 50 MHz clock for DHCOM boards - Correction in stm32prog command on uart: always flush DFU on start command - Update USB-C power detection algorithm on DK boards
2021-01-13Merge tag 'u-boot-amlogic-20210112' of ↵Tom Rini7-0/+124
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - sync amlogic GX & AXG DT to Linux 5.10 - Add new MESON_EE driver support for GXBB & AXG - Add support for Libretech-CC v2, Wetek Core2, Beelink GT-King/Pro boards - add driver for TDO tl070wsh30 panel driver - meson: isolate loading of socinfo - Add soc_rev to environment - Enable G12A support for saradc - Add correct mmcdev on VIM3(L) & Odroid-N2(C4) - Read MAC from fuses for VIM3 & VIM3L boards
2021-01-13MAINTAINERS: Update STi and STM32 maintainers emails in remaining filesPatrice Chotard12-12/+12
A previous series already update STMicroelectronics emails maintainers but some files have been omitted (Makefile, .dts, .dtsi and .rst files). Update Patrick and my email address with the one dedicated to upstream activities. Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-01-13ARM: stm32: Use firmware property instead of loadablesMichal Simek2-5/+5
There shouldn't be a need to use loadables propertyn because u-boot can be pointed by firmware property. This change should also speedup boot process because loadables property is list of strings which code is going through. On the other hand firmware can just point to one image. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13board: stm32pm1: update USB-C power detection algorithm on DK boardsPatrice Chotard1-43/+63
USB-C power supply which are Power Delivery compliant (USB-PD) are able to provide different voltage/current (for example 5V/3A 9V/3A 12V/2.25A...) In this case, the power supply need to negotiate the voltage/current to use with the device using CC1/CC2 USB-C signals. If this negotiation occurs during ADC measurement (done also on CC1/CC2 USB-C signals) some ADC acquisition can be corrupted which cause wrong power supply current detection. To avoid this, the power supply current detection algorithm is updated as following: - perform an ADC measurement, if a 3A current is detected, continue the boot process. - else, wait 20ms (max tPDDebounce duration) to ensure that USB-PD negotiation is done and perform another ADC measurement. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2021-01-13board: st: common: migrate trace to dev and log macroPatrick Delaunay4-4/+11
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-13board: st: stm32mp1: migrate trace to dev and log macroPatrick Delaunay1-69/+65
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2021-01-12Merge tag 'ti-v2021.04-rc1' of ↵Tom Rini10-10/+37
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - DM support for OMAP PWM backlight - USB host mode support for AM654 - Minor SPI fixes - Add support k2g ice board with 1GHz silicon - Fix GTC programming for K3 devices
2021-01-12Merge tag 'u-boot-atmel-2021.04-a' of ↵Tom Rini4-0/+106
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel features for 2021.04 cycle This feature set includes the new board SAMA7G5 EK, the new evaluation kit for Microchip AT91 SAMA7G5 SoC . The current board support includes two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and support for two Ethernet interfaces.
2021-01-12board: amlogic: vim3: fix setup ethernet mac from efuseArtem Lapkin1-3/+15
Fix reading built-in ethernet MAC address from efuse NOTE: MAC is stored in ASCII format, 1bytes = 2characters by 0 offset if mac from efuse not valid we use meson_generate_serial_ethaddr NOTE: remake odroid-n2.c from Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Artem Lapkin <art@khadas.com> [narmstrong: remove MAC print & spurious new endline] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-12board: ti: am335x-ice: get CDCE913 clock deviceDario Binacchi2-2/+2
With support for other clock drivers, the potentially supported CDCE913 device can no longer be probed without specifying its DT node name. Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12video: omap: move drivers to 'ti' directoryDario Binacchi2-2/+2
Add drivers/video/ti/ folder and move all TI's code in this folder for better maintenance. Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-01-12board: ti: k2g: Add support for K2G ICE with 1GHz SiliconLokesh Vutla5-6/+17
Add board detection support for K2G ICE with FlagChip 1GHz silicon. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-12board: ti: am65x: Set SERDES0 mux to PCIe to use USB 2.0 interfaceAswath Govindraju1-0/+16
It has been observed that setting SERDES0 lane mux to USB prevents USB 2.0 operation on USB0. Setting SERDES0 lane mux to non-USB when USB0 is used in USB 2.0 only mode solves this issue. However, for USB3.0+2.0 operation this issue is not present. Implement this workaround by writing 1 to LANE_FUNC_SEL field in CTRLMMR_SERDES0_CTRL register. Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-01-12sunxi: board: add a config option to fixup a Bluetooth addressAndre Heider1-0/+35
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3, ship with the controller default address. Add a config option to fix it up so it can function properly. Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Ondrej Jirman <megous@megous.com> Acked-by: Maxime Ripard <mripard@kernel.org> [rebased] Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-12sunxi: board: extract creating a unique sid into a helper functionAndre Heider1-47/+58
Refactor setup_environment() so we can use the created sid for a Bluetooth address too. Signed-off-by: Andre Heider <a.heider@gmail.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> [rebased] Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-12sunxi: board: Move USB ethernet initialization to board_late_init()Andy Shevchenko1-0/+5
For the sake of consistency (*) and order of initialization, i.e. after we have got the ethernet address, interrupt and timer initialized, try to initialize USB ethernet gadget. *) for example, zynqmp uses same order. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-12sunxi: add PineCube boardIcenowy Zheng1-0/+5
PineCube is an IP camera development kit released by Pine64. It comes with the following compoents: - A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC, a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps Ethernet port and FPC connectors for camera and daughter board. - An OV5640-based camera module which is connected to the parallel CSI bus of the mainboard. - A daughterboard with several buttons, a SD slot, some IR LEDs, a microphone and a speaker connector. As the device tree is synchronized in a previous commit, just add it to Makefile, create a new MAINTAINER item and provide a defconfig. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-11Merge branch 'next'Tom Rini83-277/+613
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-11board: amlogic: add MMC boot device detection for environment loadMarek Szyprowski2-0/+16
Detect eMMC or SD card boot on Odroid-C4/N2 and Khadas VIM3(l) boards and report proper MMC device for the environment loading code. This allows to automatically load and store environment variables on the FAT partition or RAW offset of the MMC device without the need to use different configurations on eMMC and SD card. To use this feature with environment stored on FAT partition, one has to specify an empty device part (i.e. ":1" for the first partition) in CONFIG_ENV_FAT_DEVICE_AND_PART to let the code to set the device to the value returned by mmc_get_env_dev() function. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11boards: amlogic: add Beelink S922X board family supportChristian Hewitt3-0/+69
Copied from Odroid N2. Add myself as maintainer. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11board: amlogic: vim3: read ethernet MAC address from efuseMarek Szyprowski1-0/+19
Add the board specific code for reading built-in ethernet MAC address from efuse. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11boards: amlogic: update documentation for WeTek Core2Christian Hewitt1-0/+1
Update the device matrix and add build instructions. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> [narmstrong: added wetek-core2.rst to q200 MAINTAINERS and added blank lines to fix build] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11boards: amlogic: add WeTek Core2 supportChristian Hewitt1-0/+1
Add a config for the WeTek Core2, largely based on the VIM2 config. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> [narmstrong: added wetek-core2_defconfig to q200 MAINTAINERS] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11meson: Add soc_rev to environmentPascal Vizeli1-0/+5
Add SoC revision to environment. This can be useful to select the correct device tree at runtime (N2/N2+). Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch> Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-11arm64: meson: add support for libretech-cc v2Jerome Brunet1-0/+1
Add support for the Amlogic based libretech cc version 2. As version 1, it is based on the s905x SoC. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> [narmstrong: Fixed libretech-cc.rst bullet points] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-01-08xea: spl: Disable pull UP for GPIO0_2{35}Lukasz Majewski1-1/+1
On the imx287 pin GPMI_WRN (GPIO0_25) no PullUP is available that can be enabled. To get the same behavior for both boot select pins (i.e. GPIO0_2{35}) disable pull UPs on both. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2021-01-07board: atmel: sama7g5ek: add support for MAC address retreivalEugen Hristev1-5/+13
Obtain two MAC addresses from the two EEPROMs and configure the two available Ethernet interfaces accordingly. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07configs: sama7g5: add mmc config for sdmmc0Eugen Hristev1-0/+1
Add new config for storing environment from sdmmc0. Also clean-up sama7g5ek_emmc1 to point to the proper mmc device. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-07board: atmel: sama7g5ek: add initial support for sama7g5ekEugen Hristev4-0/+97
Add initial support for sama7g5 evaluation kit board. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-01-06Merge tag 'xilinx-for-v2021.04' of ↵Tom Rini6-2/+9
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2021.04 arm64: - DT updates microblaze: - Add support for NOR device support spi: - Fix unaligned data write issue nand: - Minor code change xilinx: - Fru fix in limit calculation - Fill git repo link for all Xilinx boards video: - Add support for seps525 spi display tools: - Minor Vitis file support cmd/common - Minor code indentation fixes serial: - Uartlite debug uart initialization fix
2021-01-06Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into nextTom Rini59-96/+99
Driver model: make some udevice fields private Driver model: Rename U_BOOT_DEVICE et al. dtoc: Tidy up and add more tests ns16550 code clean-up x86 and sandbox minor fixes for of-platdata dtoc prepration for adding build-time instantiation
2021-01-06Merge tag 'v2021.01-rc5' into nextTom Rini67-556/+2097
Prepare v2021.01-rc5 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-06Merge tag 'ti-v2021.01-rc5' of ↵Tom Rini1-2/+2
https://gitlab.denx.de/u-boot/custodians/u-boot-ti - Fix I2C speed for Nokia RX51
2021-01-05dm: Rename DM_GET_DRIVER() to DM_DRIVER_GET()Simon Glass13-24/+24
In the spirit of using the same base name for all of these related macros, rename this to have the operation at the end. This is not widely used so the impact is fairly small. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: Rename U_BOOT_DEVICE() to U_BOOT_DRVINFO()Simon Glass30-41/+41
The current macro is a misnomer since it does not declare a device directly. Instead, it declares driver_info record which U-Boot uses at runtime to create a device. The distinction seems somewhat minor most of the time, but is becomes quite confusing when we actually want to declare a device, with of-platdata. We are left trying to distinguish between a device which isn't actually device, and a device that is (perhaps an 'instance'?) It seems better to rename this macro to describe what it actually is. The macros is not widely used, since boards should use devicetree to declare devices. Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is declaring a new driver_info record, not a device. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05dm: core: Access device ofnode through functionsSimon Glass1-1/+1
At present ofnode is present in the device even if it is never used. With of-platdata this field is not used, so can be removed. In preparation for this, change the access to go through inline functions. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05x86: apl: Reduce size for TPLSimon Glass1-1/+3
Update various drivers to use of_match_ptr() and to avoid including debug strings in TPL. Omit the WiFi driver entirely, since it is not used in TPL. This reduces the TPL binary size by about 608 bytes. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05serial: Rename ns16550 functions to lower caseSimon Glass14-25/+26
Lower case should be used for function names. Update this driver and its callers accordingly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05serial: Update NS16550_t and struct NS16550Simon Glass14-29/+29
Typedefs should not be used in U-Boot and structs should be lower case. Update the code to use struct ns16550 consistently. Put a header guard on the file while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-05Nokia RX-51: Decrease i2c speed to 100000Pali Rohár1-2/+2
It looks like that i2c bus lot of times timeout on some units. Prior migration to CONFIG_DM_I2C i2c speed was set to CONFIG_SYS_OMAP24_I2C_SPEED value which was 100000. Lower speed fixes timeout problems, so change speed back to its previous value. Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 8d8c18170325 ("Nokia RX-51: Convert to CONFIG_DM_I2C") Reviewed-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-01-05xilinx: Fill git repository for Xilinx boardsMichal Simek4-0/+4
All Xilinx SoCs have repository location filled already but boards are covered by different fragment which is missing this link. The patch is extending description with adding proper link to the same repository. Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-05fru: ops: avoid out of bounds accessHeinrich Schuchardt1-1/+1
Building xilinx_zynq_virt_defconfig fails on origin/next as reported by GCC 10.2 (as provided by Debian Bullseye): CC board/xilinx/common/fru_ops.o board/xilinx/common/fru_ops.c: In function ‘fru_capture’: board/xilinx/common/fru_ops.c:173:8: error: array subscript 284 is outside array bounds of ‘struct fru_table[1]’ [-Werror=array-bounds] 173 | limit = data + sizeof(struct fru_board_data); | ~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ board/xilinx/common/fru_ops.c:17:18: note: while referencing ‘fru_data’ 17 | struct fru_table fru_data __section(.data); | ^~~~~~~~ When using sizeof(struct fru_board_data) to find the end of the structure you should add it to the start of the structure. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-01-04microblaze: Set script_offset_nor env variableT Karthik Reddy1-1/+4
Set script_offset_nor env variable using CONFIG_BOOT_SCRIPT_OFFSET and nor flash start address to keep bootscript offset configurable. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-12-31efi: capsule: Add support for uefi capsule authenticationSughosh Ganu2-0/+49
Add support for authenticating uefi capsules. Most of the signature verification functionality is shared with the uefi secure boot feature. The root certificate containing the public key used for the signature verification is stored as part of the device tree blob. The root certificate is stored as an efi signature list(esl) file -- this file contains the x509 certificate which is the root certificate. Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31qemu: common: Set dfu_alt_info variable for the platformSughosh Ganu3-0/+70
The dfu framework uses the dfu_alt_info environment variable to get information that is needed for performing the firmware update. Add logic to set the dfu_alt_info for the qemu arm64 platform to reflect the two mtd partitions created for the u-boot env and the firmware image. This can be subsequently extended for other qemu architectures which need this variable set. Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31qemu: common: Add support for dynamic mtdparts for the platformSughosh Ganu4-0/+107
Add support for setting the default values for mtd partitions on the platform. This would be used for updating the firmware image using uefi capsule update with the dfu mtd backend driver. Currently, values have been defined for the qemu arm64 platform, with default values defined for the mtd partitions based on the NOR flash. This can be subsequently extended for other qemu architectures which need mtdparts set. Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-31qemu: arm: Initialise virtio devices in board_late_initSughosh Ganu1-0/+5
On the qemu arm platform, the virtio devices are initialised in the board_init function, which gets called before the initr_pci. With this sequence, the virtio block devices on the pci bus are not initialised. Move the initialisation of the virtio devices to board_late_init which gets called after the call to initr_pci. Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-12-26arm: dart6ul: read and print SoM info from eeprom on startupMarc Ferland1-1/+103
The dart6ul has an i2c eeprom at 0x50 which contains, among other things, the manufacturing/revision/options info of the SoM. This patch replaces the current checkboard() implementation with a more exhaustive one based on the content of the eeprom. Since this code uses the new driver model, some changes were also required in the DTS to make the nodes related to i2c available before relocation. This code was inspired from the supported u-boot code from Variscite which can be found here: https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02 New output example: Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17 Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G Signed-off-by: Marc Ferland <ferlandm@amotus.ca> Reviewed-by: Fabio Estevam <festevam@gmail.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-20 05:42:36 +0300