summaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)AuthorFilesLines
2019-10-26Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mipsTom Rini2-2/+2
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs - bmips: various small fixes - mtmips: add new drivers for clock, reset-controller and pinctrl - mtmips: add support for high speed UART - mtmips: update/enhance drivers for SPI and ethernet - mtmips: add support for MMC
2019-10-26Merge branch '2019-10-24-ti-imports'Tom Rini1-0/+1
- Enable DFU on dra7xx boards - Further Keystone 3 platform improvements
2019-10-26armv7R: K3: j721e: Add support for triggering ddr init from SPLLokesh Vutla1-0/+1
In SPL, DDR should be made available by the end of board_init_f() so that apis in board_init_r() can use ddr. Adding support for triggering DDR initialization from board_init_f(). Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini1-13/+0
- DWC3 improvements - i.MX7 EHCI bugfix
2019-10-25Merge tag 'u-boot-atmel-2020.01-b' of ↵Tom Rini1-0/+12
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel Second set of u-boot-atmel features and fixes for 2020.01 cycle This feature set includes Eugen's work on a new tiny flexcom driver and eeprom mac retrieval for the sam9x60-ek board.
2019-10-25bmips: correct name charactersÁlvaro Fernández Rojas2-2/+2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-10-24ARM: zynq: Remove unused board_early_init_f()Michal Simek1-7/+0
board_early_init_f added by commit e6cc3b25d721 ("arm: zynq: Wire watchdog internals") is no longer needed that's why remove it also with Kconfig enabling. Fixes: ccd063e9812a ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)") Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24arm64: zynqmp: Convert invoke_smc() to xilinx_pm_request()Michal Simek1-2/+2
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to xilinx_pm_request() which do calculation with PM_SIP_SVC already. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24board: sam9x60ek: add support for MAC address retrievalEugen Hristev1-0/+12
Retrieve mac address from i2c eeprom at boot time. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2019-10-24ARM: keystone: Do not enable the USB power domains at the board levelJean-Jacques Hiblot1-13/+0
This breaks linux boot sequence. Observed on k2e and k2l platforms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-23Merge tag 'u-boot-stm32-2019-10-23' of ↵Tom Rini1-0/+17
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - Disable CONFIG_NET flag for MCU STM32 - Fix ramdisk_addr_r for stm32f746-disco - Fix USB product id for stm32mp1
2019-10-22board: stm32mp1: fixup the usb product id for USB download gadgetPatrick Delaunay1-0/+17
Select the correct USB product id used by the download gadget for ST stm32mp1 boards. The board stm32mp1 select the correct product id, as defined in http://www.linux-usb.org/usb.ids for the STMicroelectronics vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM): - dfu = 0xdf11 : STM Device in DFU mode it is the value used by ROM code and reused for stm32prog command - fasboot = 0x0afb : Android Fastboot device - others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM) Mass Storage Device it is used for UMS command / usb_dnl_ums This patch avoid conflict when the same USB VID/PID is used for ums, fastboot or dfu command (two different protocols associated to the same PID). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
2019-10-21board/ls1028a: Add call to sec_init()Udit Agarwal1-0/+4
Adds sec_init call to initialise the job ring parameters for secure boot operations. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-10-18Merge tag 'u-boot-amlogic-20191018' of ↵Tom Rini7-4/+328
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - document alternative libretech-cc installation methods, including upstream TF-A and opensource tools - add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board - add support for Amlogic A311D based Khadas VIM3 - add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
2019-10-18configs: sei610: Add config file to fix userdata sizeGuillaume La Roque1-0/+1
Add separate config file to handle the different eMMC size on the sei610 board. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18boards: amlogic: add SEI610 supportNeil Armstrong4-0/+157
Add support for the customer board SEI610 manufactured by SEI Robotics with the following specifications: - Amlogic S905X3 ARM Cortex-A55 quad-core SoC - 2GB DDR4 SDRAM - 10/100 Ethernet (Internal PHY) - 1 x USB 3.0 Host - 1 x USB Type-C DRD - 1 x FTDI USB Serial Debug Interface - eMMC - SDcard - Infrared receiver - SDIO WiFi Module Like it's SEI510 counterpart, the boot flow is designed to boot Android AOSP built for the Yukawa Android device. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: Add Khadas VIM3 defconfigAndreas Färber2-0/+133
Derived from odroid-n2_defconfig and README.odroid-n2. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18board: amlogic: document alternative libretech-cc installation methodsDaniel Drake1-4/+37
As already documented in this README, several binaries must be glued together in order to boot the device. Extend the documentation to cover the prebuilt binaries (saving you the hassle of installing ancient cross-compilers), and also mention the open source replacements for the encryption tool (which is especially useful if you want to avoid requiring 32-bit x86 binaries in your build system). Signed-off-by: Daniel Drake <drake@endlessm.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18configs: fu540: enable gpio driverSagar Shrikant Kadam1-0/+3
Enable the DM based GPIO driver for FU540-C000 SoC. Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-17arm: remove the H2200 boardHeinrich Schuchardt5-114/+0
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y. The maintainer Lukasz Dalek suggested to remove the board. https://lists.denx.de/pipermail/u-boot/2019-August/380685.html Cc: Lukasz Dalek <luk0104@gmail.com> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> [trini: As this is the last non-toradex PXA board, update travis too] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-15Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini7-88/+84
- vining_fpga updates
2019-10-14Merge tag 'u-boot-imx-20191014' of ↵Tom Rini13-465/+267
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191014 ------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628 - logicpd pinmux - i.MX7ULP: imx_ddr_size - fixes Toradex i.MX6/i.MX7 - pico-imx7d - tpc70 converted to DM - New Board: meerkat96 - add HAB version command - i.MX8 : imx8: Jump from alias to OCRAM address at SPL init imx8qm/qxp: Set SPL TEXT base to OCRAM base
2019-10-14imx: imx8mm_evk: add board_mmc_get_env_devPeng Fan1-0/+5
Add board_mmc_get_env_dev to correctly return devno for mmc env Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-14mx7ulp_evk: Use imx_ddr_size()Fabio Estevam1-1/+1
Use imx_ddr_size() to retrieve the total DDR size instead of passing a hardcoded memory size. imx_ddr_size() calculates the memory size based on the actual MMDC registers values and is useful to detect misconfigurations, so switch to this more robust approach. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-10-14board: Add STM32F769 SoC, discovery board supportYannick Fertré1-0/+1
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
2019-10-13colibri_imx7: provide proper node name to pmic_getIgor Opaniuk1-2/+2
Implementation of pmic_get() uses uclass_find_device_by_name(), which behaviour was changed in 4213609cc7 ("drivers: core: use strcmp when find device by name"). Now we have to supply full node name with unit address. Fixes boot issue: U-Boot 2019.07-00788-g0ef6e69a1e-dirty (Jul 19 2019 - 15:27:02 +0300) CPU: Freescale i.MX7D rev1.3 1000 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 41C Reset cause: POR DRAM: 512 MiB initcall sequence 9ffd3a4c failed at call 87803c61 (err=-19) ERROR Please RESET the board Fixes: 4213609cc7("drivers: core: use strcmp when find device by name") Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2019-10-13imx: tpc70: Convert TPC70 (imx6q) board to use DM/DTS in SPL and u-bootLukasz Majewski2-292/+6
This patch converts the TPC70 to use driver model and device tree description in both SPL and u-boot proper. Notable changes (DM/DTS conversion): - PINCTRL{_IMX6} - DM_I2C - enable 'regulator' and 'pmic' commands - DM_MMC and BLK (USDHC) - DM_ETH - DM WDT (including SYSRESET) Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: led: Enable LED default stateLukasz Majewski1-0/+4
This change sets the default state of LEDs on TPC70. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: cosmetic: Replace magic numbers when setting ENET clockLukasz Majewski1-1/+2
This is a cosmetic change, just to use proper define instead of magic numbers. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13imx: tpc70: Add board_boot_order() to distinguish between eMMC and SD bootLukasz Majewski1-0/+20
The TPC70 can boot from SD card (debug/development) and eMMC (production). The board_boot_order() function provides a run time check for the device from which one wants to boot (it is selected by GPIO pins setup). Moreover, a fallback to SD card is provided if the detection is not possible or working properly. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-13ARM: imx6q_logic: Remove legacy pinmuxing code from board file.Adam Ford1-85/+0
With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-13board: tbs2910: Convert eth to driver modelSoeren Moch1-75/+0
So we can remove lots of legacy config code. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13board: tbs2910: Convert pci to driver modelSoeren Moch1-17/+0
So we can get rid of legacy pci config code. PCI_PNP is not required for this board, remove it to reduce the size of the u-boot binary. DM_PCI does not start the host controller automatically anymore. Do so in preboot instead. Signed-off-by: Soeren Moch <smoch@web.de>
2019-10-13Add i.MX7D based Meerkat96 board supportShawn Guo6-0/+235
The Meerkat96 board, based on the NXP i.MX7D SoC, is a member of 96Boards community and complies with all Consumer Edition board specifications. https://www.novtech.com/products/meerkat96.html https://www.96boards.org/product/imx7-96/ The initial supported/tested devices include: - Debug serial - SD - USB Host (with Ethernet) With these support, it's good enough for loading Linux Kernel from SD or Ethernet over USB. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
2019-10-12Merge branch '2019-10-11-master-imports'Tom Rini1-7/+0
- Assorted cleanups - FAT bugfixes - mediatek platform updates
2019-10-12sandbox: Remove sandbox_noblk buildTom Rini1-7/+0
At this point, all drivers that do not use CONFIG_BLK are past their migration deadlines, so remove this config as it's no longer helpful and hinders enhancing block drivers. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-11board: ti: am335x-ice: Configure the CDCE913 clock synthesizerTero Kristo1-0/+4
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am43xx-idk: Configure the CDCE913 clock synthesizerTero Kristo1-0/+5
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: ti: am57xx-idk: Configure the CDCE913 clock synthesizerTero Kristo1-0/+5
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their reset crystal capacitance load value of 10pF is wrong leading into lost packets in certain networking tests. Add DT data for this device, and probe it from the board file to program the crystal capacitance load value to 0pF to avoid any problems. Signed-off-by: Tero Kristo <t-kristo@ti.com>
2019-10-11board: am65x: Print board name and version during bootLokesh Vutla1-1/+14
Print the board name and ver along with the DT Model. While at it print the ver for all the detected daughter cards. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11am335x, guardian: update guardian boardMoses Christopher2-21/+64
- add BOARD_LATE_INIT function calls in board.c - add swi_status detection in board.c - mux: add guardian interfaces to single pinmux structure - am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-10-11board: j721e: Add READMELokesh Vutla1-0/+227
Add README file explaining the build and boot procedure for J721E evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11board: ti: am65x: Add UART boot procedure in READMEAndreas Dannenberg1-0/+32
am65x ROM support booting over UART. And U-Boot built for am65x EVM supports UART boot as well. Add the UART boot procedure into the README also providing a corresponding example command sequence for execution on a host PC. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-09ARM: socfpga: vining_fpga: Extract eth1 MAC from EEPROMMarek Vasut1-0/+2
The EEPROM contains eth1 MAC address as well, use it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09ARM: socfpga: vining_fpga: Update generated headersMarek Vasut4-88/+82
Update headers generated by quartus to the latest version. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09ARM: socfpga: vining_fpga: Rename VINING|FPGAMarek Vasut7-0/+0
The company Samtec was merged into Softing, migrate the board over to the new name and update copyright headers. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Silvio Fricke <silvio.fricke@softing.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-10-09Merge tag 'xilinx-for-v2020.01' of ↵Tom Rini14-24/+1399
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
2019-10-09Merge tag 'u-boot-imx-20191009' of ↵Tom Rini62-581/+3550
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191009 ------------------- Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532 - MX6UL / ULZ - Toradex board - Allow to set OCRAM for MX6Q/D - MX7ULP - MX8: (container image, imx8mq_mek), SCU API - fix several board booting from SD/EMMC (cubox-i for example) - pico boards [trini: display5 merged manually] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-09Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini2-2/+2
- Rename existing FSP code to fsp1 - Add fsp2 directory in preparation to support FSP 2.0 - Various x86 platform codes update - Various bug fixes and updates in dm core, sandbox and spl
2019-10-08ARM: imx6q_logic: Fix MMC2 bootingAdam Ford1-0/+29
With the reverting of a previous change to spl_boot_device, this board needs a new solution to determining if we're booting from MMC1 or MMC2. This patch creates board_boot_order function which overrides the standard, and returns not only MMC1, or MMC2, but also can fall back to NAND or the serial downloader should other boot options fail. Signed-off-by: Adam Ford <aford173@gmail.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-10 00:36:40 +0300