Age | Commit message (Collapse) | Author | Files | Lines |
|
In case the eMMC contains any GP partitions or user sets up new GP
partitions, the size of these GP partitions reduce the size of the
USER partition. Subtract the size of those GP partitions from the
calculated size of USER partition when using `user enh start -`.
The following test used to fail before:
```
u-boot=> mmc hwpartition gp1 524288 enh user enh 0 - wrrel on check
Partition configuration:
User Enhanced Start: 0 Bytes
User Enhanced Size: 1.8 GiB
User partition write reliability: on
GP1 Capacity: 256 MiB ENH
No GP2 partition
No GP3 partition
No GP4 partition
Total enhanced size exceeds maximum (261 > 229)
Failed!
```
The test now passes:
```
u-boot=> mmc hwpartition gp1 524288 enh user enh 0 - wrrel on check
Partition configuration:
User Enhanced Start: 0 Bytes
User Enhanced Size: 1.5 GiB
User partition write reliability: on
GP1 Capacity: 256 MiB ENH
No GP2 partition
No GP3 partition
No GP4 partition
```
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20211022
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/10887
- imx8 : Toradex Verdin MX8M Plus
Kontron pitx-imx8m
- imx8ulp: several fixes and improvements
- imx6ull fixes
- switching to binman
|
|
The operation of this function can be confusing. Add some debugging so
we can see what it is doing and when it is called.
Also drop the preprocessor usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Without this patch the bcb struct could be located at an odd address
which resulted in data not being copied to the buffer.
Here was the repro steps (from Mattijs):
=> mmc dev 1
=> bcb load 1 misc
=> bcb dump command
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
=> part start mmc 1 misc misc_start
=> mmc read ${loadaddr} ${misc_start} 4
=> bcb load 1 misc
=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 62 6f 6f 74 6c 6f 61
00000010: 64 65 72 00 00 00 00 00 00 00 00 00 00 00 00 00
This behavior was observed on an Amlogic A311D (ARM64) platform with a
recent GCC toolchain (11.2.0) but is most likely affecting other
platforms.
To avoid issues the structure is aligned on DMA minimum alignment value
as it is passed directly to the read function.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
|
|
At present we use wide characters for unicode but this is not necessary.
Change the code to use the 'u' literal instead. This helps to fix build
warnings for sandbox on rpi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Allow to call 'pci' and 'pci regions' commands with bus option '*' which
cause pci to process all buses.
PCIe is point-to-point HW and so on each bus is maximally one physical
device. Therefore for PCIe it is common to have multiple buses.
This change allows to easily print all available PCIe devices in system.
Make '*' as default option when no bus argument is specified.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Currently pci command ignores invalid cmdline arguments and do something.
Add checks that all passed arguments were processed.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
'pci regions' currently prints only region information from bus 0 which
belongs to controller 0. Parser for 'pci regions' cmdline currently ignores
any additional arguments and so U-Boot always uses bus 0.
Regions are stored in controller (not on the bus) and therefore to retrieve
controller from the bus, it is needed to call pci_get_controller() which
returns root bus. Because bus 0 is root bus, current code worked fine for
controller 0.
Extend cmdline parser for 'pci regions' to allows specifying bus number,
extend pci_show_regions() code to accept also non-zero bus number and
print bus ranges for which is regions configuration assigned.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
At present this is really just a debugging aid, but it is a bit untidy.
Add proper columns so it is easier to read.
Sample output for coral:
=> acpi list
Name Base Size Detail
---- -------- ----- ------
RSDP 79925000 24 v02 U-BOOT
RSDT 79925030 48 v01 U-BOOT U-BOOTBL 20220101 INTL 0
XSDT 799250e0 6c v01 U-BOOT U-BOOTBL 20220101 INTL 0
FACP 79929570 f4 v04 U-BOOT U-BOOTBL 20220101 INTL 1
DSDT 79925280 32ea v02 U-BOOT U-BOOTBL 20110725 INTL 20180105
FACS 79925240 40
MCFG 79929670 2c v01 U-BOOT U-BOOTBL 20220101 INTL 0
SPCR 799296a0 50 v02 U-BOOT U-BOOTBL 20220101 INTL 0
TPM2 799296f0 4c v04 U-BOOT U-BOOTBL 20220101 INTL 0
APIC 79929740 6c v02 U-BOOT U-BOOTBL 20220101 INTL 0
SSDT 799297b0 1523 v02 U-BOOT U-BOOTBL 20220101 INTL 1
NHLT 7992ace0 e60 v05 coral coral 3 INTL 0
DBG2 7992db40 61 v00 U-BOOT U-BOOTBL 20220101 INTL 0
HPET 7992dbb0 38 v01 U-BOOT U-BOOTBL 20220101 INTL 0
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow this to be used on any arch. Also convert to using macros so that
we can check the CONFIG option in C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add Kconfig option(CONFIG_CMD_MP) to enable or disable multiprocessor
commands. Compile cmd/mp.c based on CONFIG_CMD_MP.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1-2
Documentation:
* describe printf() format codes
UEFI
* enable more algorithms for UEFI image verification, e.g. SHA256-RSA2048
General
* simplify printing short texts for GUIDs
* provide a unit test for printing GUIDs
|
|
Replace CONFIG_SYS_MAX_FLASH_BANKS by CFI_FLASH_BANKS to prepare
Kconfig migration and avoid to redefine CONFIG_SYS_MAX_FLASH_BANKS
in cfi_flash.h.
After this patch CONFIG_SYS_MAX_FLASH_BANKS should be never used in
the cfi code: use CFI_MAX_FLASH_BANKS for struct size or CFI_FLASH_BANKS
for number of CFI banks which can be dynamic.
This patch modify all the files which include mtd/cfi_flash.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Tidy up the warnings reported by checkpatch.pl to prepare next patches
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use IS_ENABLED() instead, to reduce the number of build paths.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Sphinx expects Return: and not @return to indicate a return value.
find . -name '*.c' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
find . -name '*.h' -exec \
sed -i 's/^\(\s\)\*\(\s*\)@return\(\s\)/\1*\2Return:\3/' {} \;
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Use "%pS" to print text representations of GUIDs.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Use "%pS" to print text representations of GUIDs.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Commit 98f705c9cefd ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
|
|
At present the 'efi' command only works in the EFI payload. Update it to
work in the app too, so the memory map can be examined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
At present this function requires a pointer to struct efi_entry_memmap
but the only field used in there is the desc_size. We want to be able
to use it from the app, so update it to use desc_size directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
U-Boot, in some occasions, injects a 'kaslr-seed' property on the /chosen
node. That would be problematic in case we want to measure the DTB we
install in the configuration table, since it would change across reboots.
The Linux kernel EFI-stub completely ignores it and only relies on
EFI_RNG_PROTOCOL for it's own randomness needs (i.e the randomization
of the physical placement of the kernel). In fact it (blindly) overwrites
the existing seed if the protocol is installed. However it still uses it
for randomizing it's virtual placement.
So let's get rid of it in the presence of the RNG protocol.
It's worth noting that TPMs also provide an RNG. So if we tweak our
EFI_RNG_PROTOCOL slightly and install the protocol when a TPM device
is present the 'kaslr-seed' property will always be removed, allowing
us to reliably measure our DTB.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
|
|
A GPT partition table typically has 128 entries. If a partition table
contains a partition 128 'part list' should be able to list it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
|
|
Reporting the return value should always be done on error conditions,
this way the developer can start debugging issues with more knowledge
in-hand.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
|
|
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
|
|
https://source.denx.de/u-boot/custodians/u-boot-video into next
- various fixes to the sandbox display support
- support for showing a logo without splash screen config
- support for BMP drawing to depths other than 16bpp
- tests for the different types of supported BMP images
- support showing a logo when running coreboot via qemu
|
|
This converts the following to Kconfig:
CONFIG_JFFS2_DEV
CONFIG_JFFS2_LZO
CONFIG_JFFS2_NAND
CONFIG_JFFS2_PART_OFFSET
CONFIG_JFFS2_PART_SIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This does not work with sandbox at present. Fix it up to use map_sysmem()
to convert an address to a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Allow the kaslr-seed value in the chosen node to be set from a hardware
rng source.
Tested on a Rockchip PX30 (Odroid Go Advance), you must have loaded
the devicetree first and prepared it for editing. On my device the
workflow goes as follows:
setenv dtb_loadaddr "0x01f00000"
load mmc 0:1 ${dtb_loadaddr} rk3326-odroid-go2.dtb
fdt addr ${dtb_loadaddr}
fdt resize
kaslrseed
and the output can be seen here:
fdt print /chosen
chosen {
kaslr-seed = <0x6f61df74 0x6f7b996c>;
stdout-path = "serial2:115200n8";
};
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
It can be confusing to figure out where the devicetree came from. It seems
important enough to warrant a message during boot. Add information about
the number of devices and uclasses too since it is helpful to have some
idea what is going on with driver model.
Report the devicetree source in bdinfo too.
This looks something like this, with > marking the new line.
U-Boot 2021.10-00190 (Oct 30 2021 - 09:01:29 -0600)
DRAM: 128 MiB
> Core: 42 devices, 11 uclasses, devicetree: passage
Flash: 64 MiB
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Prepare v2022.01-rc4
|
|
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
At present there are Kconfig options for tracing, but sandbox uses
plain #defines to set them. Correct this and make the tracing command
default to enabled so that this is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The current tpm2_pcr_read is hardcoded using SHA256. Make the
actual command to TPM configurable to use wider range of algorithms.
The current command line is kept as is i.e limited to SHA-256 only.
Signed-off-by: Ruchika Gupta <ruchika.gupta@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Prepare v2022.01-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
At present this command considers the partitions to be identical if the
start and size are smaller than expected. It should check that they are
the same. Fix this and tidy up the code style a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Update this code to use IS_ENABLED() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
This is not updated at runtime so should be marked const. Update the code
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
This command is not compiled by default and has not been updated alongside
changes to the tpmv1 API, such as passing the TPM udevice to the relevant
functions.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
This command is not compiled by default and was not
updated to pass the udevice to tpm_get_capability.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
This has different semantics in different places. Go with the bootm method
and put it in a common function so that the behaviour is consistent in
U-Boot. Update the docs.
To be clear, this changes the way that 'bootelf' and standalone boot
work. Before, if autostart was set to "fred" or "YES", for example, they
would consider that a "yes". This may change behaviour for some boards,
but the only in-tree boards which mention autostart use "no" to disable
it, which will still work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Wolfgang Denk <wd@denx.de>
|
|
Refactor this code so that we can call the 'pxe get' command without going
through the command-line interpreter. This makes it easier to get the
information we need, without going through environment variables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The only difference between the three helpers is the filesystem type.
Factor this out and call the filesystem functions directly, instead of
through the command-line interpreter. This allows the file size to be
obtained directly, instead of via an environment variable.
We cannot do the same thing with PXE's tftpboot since there is no API
at present to obtain information about the file that was read. So there
is no point in changing pxe_getfile_func to use a ulong for the address,
for example.
This is as far as the refactoring can go for the present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
It is pretty strange that the pxe code uses the 'filesize' environment
variable find the size of a file it has just read.
Partly this is because it uses the command-line interpreter to parse its
request to load the file.
As a first step towards unwinding this, return it directly from the
getfile() function. This makes the code a bit longer, for now, but will be
cleaned up in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
The 'bootfile' environment variable is read in the bowels of pxe_util to
provide a directory to which all loaded files are relative.
This is not obvious from the API to PXE and it is strange to make the
caller set an environment variable rather than pass this as a parameter.
The code is also convoluted, which this feature implemented by
get_bootfile_path().
Update the API to improve this. Unfortunately this means that
pxe_setup_ctx() can fail, so add error checking.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
Both the syslinux and pxe commands use essentially the same code to parse
and run extlinux.conf files. Move this into a common function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Tested-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|