summaryrefslogtreecommitdiff
path: root/configs/T2080RDB_revD_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2022-12-22Convert CONFIG_HOSTNAME et al to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_GATEWAYIP CONFIG_HOSTNAME CONFIG_IPADDR CONFIG_NETMASK CONFIG_ROOTPATH CONFIG_SERVERIP CONFIG_UBOOTPATH To do this, we introduce a CONFIG_USE_ form of each of the above and change include/env_default.h to test for that to be set before setting a value. Further, we don't want to stringify the IP address related values as they are now properly strings via Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-06Convert CONFIG_SYS_NS16550_MEM32 et al to KconfigTom Rini1-1/+1
This converts the following to Kconfig: CONFIG_SPL_NS16550_MIN_FUNCTIONS CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that platforms can enable the legacy driver here for SPL. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-11-10Convert CONFIG_SYS_MONITOR_LEN to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10Convert CONFIG_SYS_INIT_RAM_LOCK to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_INIT_RAM_LOCK Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-10-31Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass1-1/+1
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-21configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-23configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-12Convert CONFIG_SYS_FSL_NUM_CC_PLLS to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_FSL_NUM_CC_PLLS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-04Convert CONFIG_FSL_CORENET to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_FSL_CORENET Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-04Convert CONFIG_SYS_FLASH_QUIET_TEST to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_FLASH_QUIET_TEST Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-04Convert CONFIG_SYS_MAX_FLASH_SECT to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_MAX_FLASH_SECT Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-04Convert CONFIG_SYS_FLASH_EMPTY_INFO to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_FLASH_EMPTY_INFO Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-09Convert CONFIG_SYS_CACHE_STASHING to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_CACHE_STASHING Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07Merge branch '2022-07-07-Kconfig-migrations-dead-code-removal' into nextTom Rini1-7/+2
- Migrate more CONFIG options to Kconfig and remove some unused code while we're at it.
2022-07-07Convert CONFIG_SYS_FSL_CPC et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_FSL_CPC CONFIG_SYS_CPC_REINIT_F Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07Convert CONFIG_SYS_BOOK3E_HV to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_BOOK3E_HV Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-06Convert CONFIG_PCIE1 et al to KconfigTom Rini1-0/+11
This converts the following to Kconfig: CONFIG_PCIE1 CONFIG_PCIE2 CONFIG_PCIE3 CONFIG_PCIE4 CONFIG_PCI1 Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-06Convert CONFIG_ENABLE_36BIT_PHYS to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_ENABLE_36BIT_PHYS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-29Convert CONFIG_USB_MAX_CONTROLLER_COUNT to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_USB_MAX_CONTROLLER_COUNT Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-29Convert CONFIG_FSL_SATA_V2 to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_FSL_SATA_V2 Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_PBSIZE to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-13configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-12PPC: Enable Job ring driver model.Gaurav Jain1-0/+1
removed sec_init() call from board files. sec is initialized based on job ring information processed from device tree. Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2022-04-08configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ETHPRIME to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-04Convert CONFIG_BOOTFILE to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_BOOTFILE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-09Convert CONFIG_SCSI_AHCI_PLAT et al to KconfigSimon Glass1-0/+1
This converts the following to Kconfig: CONFIG_SCSI_AHCI_PLAT CONFIG_SYS_SCSI_MAX_SCSI_ID CONFIG_SYS_SCSI_MAX_LUN CONFIG_SYS_SATA_MAX_DEVICE Drop CONFIG_SCSI for everything except the sandbox build. We only need one build for tests. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-01-25configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27Finish CONFIG_VID et al conversion to KconfigTom Rini1-0/+4
This converts the following to Kconfig: CONFIG_VID CONFIG_VOL_MONITOR_INA220 CONFIG_VOL_MONITOR_IR36021_READ CONFIG_VOL_MONITOR_IR36021_SET CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET To finish this migration, we first need to introduce CONFIG_SPL_VID as some platforms only use this code in full U-Boot while others use it in SPL as well. To make the Kconfig logic clearer, guard all of the sub-options with a if VID || SPL_VID check. Finally, add Kconfig options for the remaining related options that did not previously have one. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01Convert CONFIG_USE_BOOTCOMMAND et al to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-09configs: fsl: migrate FMAN/QE specific defines to KconfigRajesh Bhagat1-0/+1
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR, CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and move these entries to defconfigs. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-10-15configs: Resync with savedefconfigTom Rini1-1/+0
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01nxp: Migrate a number of DDR related symbols to KconfigTom Rini1-0/+2
- Guard most of the options in drivers/ddr/fsl/Kconfig with SYS_FSL_DDR || SYS_FSL_MMDC. - Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER to Kconfig. - Clean up the logic for including the DDR_ECC_CMD code. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01nxp: Migrate CONFIG_DDR_CLK_FREQ to KconfigTom Rini1-0/+1
As this symbol can either be a fixed value or the function get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ to that value and now include/clock_legacy.h contains the function prototype or defines get_board_ddr_clk() to that static value. Update callers to test for DYNAMIC or STATIC. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_I2C_SET_DEFAULT_BUS_NUM et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_I2C_SET_DEFAULT_BUS_NUM CONFIG_I2C_DEFAULT_BUS_NUMBER Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30i2c: fsl_i2c: Migrate to KconfigTom Rini1-0/+8
- As there are no boards that use different values for speed / slave on different buses, use a single option. - Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options. - Introduce _HAS_ options for additional buses as only the first one is common to all users. - Convert all remaining symbols to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini1-0/+1
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to KconfigTom Rini1-0/+2
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-18configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to KconfigKuldeep Singh1-0/+1
Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-07-27configs: Resync with savedefconfigTom Rini1-2/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-17board: freescale: t208xrdb: add a config option for rev D dts fixupsCamelia Groza1-0/+77
Under DM, we rely on u-boot's device tree to provide the correct PHY addresses. The board_fix_fdt callback is intended to be used for device tree fixups before relocation. Unfortunately, this isn't an option when booting from flash since the device tree isn't writable before relocation. This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a board revision D or up is the target. The config option is used to set the correct Aquantia PHY address in the board's u-boot device tree. Defconfig files with the option enable explicitly are added for convenience. Signed-off-by: Camelia Groza <camelia.groza@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-24 15:41:06 +0300