summaryrefslogtreecommitdiff
path: root/configs/khadas-vim3_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2020-10-18configs: migrate CONFIG_BMP_16/24/32BPP to defconfigsPatrick Delaunay1-0/+3
Done with: ./tools/moveconfig.py BMP_16BPP BMP_24BPP BMP_32BPP Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-10-18configs: migrate CONFIG_VIDEO_BMP_RLE8 to defconfigsPatrick Delaunay1-0/+1
Done with: ./tools/moveconfig.py VIDEO_BMP_RLE8 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-10-09configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-05board: amlogic: vim3: add support for dynamic PCIe enableNeil Armstrong1-0/+3
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between an USB3.0 Type A connector and a M.2 Key M slot. The PHY driving these differential lines is shared between the USB3.0 controller and the PCIe Controller, thus only a single controller can use it. This adds this dynamic switching right before booting Linux and the configuration steps in the boards documentation. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> [narmstrong: fixed warning by replacing min() by min_t()]
2020-10-05configs: vim3: use the vim3 board supportNeil Armstrong1-1/+1
Use the newly added VIM3 board support instead of the generic W400. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-08-23Convert CONFIG_SPLASH_SCREEN et al to KconfigSimon Glass1-0/+2
This converts the following to Kconfig: CONFIG_SPLASH_SCREEN CONFIG_SPLASH_SCREEN_ALIGN CONFIG_SPLASHIMAGE_GUARD CONFIG_SPLASH_SOURCE Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-10configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-05configs: Resync with savedefconfigTom Rini1-2/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-29configs: khadas-vim3: enable HDMI outputNeil Armstrong1-0/+9
Enable options to permit HDMI output on Khadas VIM3 & VIM3L boards. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-04-28configs: khadas-vim3: enable support for SPI NOR flashNeil Armstrong1-0/+9
Enable the necessary configs to make usage of the SPI NOR Flash. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-21env: Finish migration of common ENV optionsTom Rini1-0/+1
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini1-0/+1
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-24configs: sei610: khadas-vim3 : disable Gadget support for the DWC3Jean-Jacques Hiblot1-0/+1
Those platform use the DWC2 controller for the gadget support and the DWC3 for host-only operations. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-18configs: Add Khadas VIM3 defconfigAndreas Färber1-0/+54
Derived from odroid-n2_defconfig and README.odroid-n2. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 17:19:47 +0300