summaryrefslogtreecommitdiff
path: root/configs/ls1012ardb_tfa_SECURE_BOOT_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2020-06-05Convert CONFIG_CMD_ASKENV et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_CMD_ASKENV CONFIG_CMD_BMP CONFIG_CMD_BOOTD CONFIG_CMD_CACHE CONFIG_CMD_CRC32 CONFIG_CMD_DHCP CONFIG_CMD_ENV CONFIG_CMD_EXPORTENV CONFIG_CMD_EXT2 CONFIG_CMD_EXT4 CONFIG_CMD_FLASH CONFIG_CMD_FS_GENERIC CONFIG_CMD_FUSE CONFIG_CMD_GPIO CONFIG_CMD_GPT CONFIG_CMD_GREPENV CONFIG_CMD_I2C CONFIG_CMD_IMLS CONFIG_CMD_IMPORTENV CONFIG_CMD_LOADB CONFIG_CMD_LOADS CONFIG_CMD_MEMINFO CONFIG_CMD_MII CONFIG_CMD_MTDPARTS CONFIG_CMD_NAND CONFIG_CMD_NAND_TRIMFFS CONFIG_CMD_NFS CONFIG_CMD_PCA953X CONFIG_CMD_PCA953X_INFO CONFIG_CMD_PCI CONFIG_CMD_PING CONFIG_CMD_READ CONFIG_CMD_SF CONFIG_CMD_SPI CONFIG_CMD_SPL CONFIG_CMD_SPL_WRITE_SIZE CONFIG_CMD_TIME CONFIG_CMD_TRACE CONFIG_CMD_UBI CONFIG_CMD_UBIFS CONFIG_CMD_UNZIP CONFIG_FS_EXT4 Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-19configs: ls1012a: Reduce CONFIG_ENV_SIZE to 0x2000Ashish Kumar1-1/+1
All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE values. If both config values are same, flash environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be same as that of flash sector size, this entry cannot be changed. Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config value aligned with other boards environemt size. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-19configs: ls1012a: Enable CONFIG_SPI_FLASH_SPANSION in defconfigsKuldeep Singh1-0/+1
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion flashes. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma1-0/+2
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28configs: Resync with savedefconfigTom Rini1-3/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-30configs: ls1012ardb: secure boot: Add PFE configPriyanka Singh1-0/+2
Add config to enable the PFE and ETH support. Also change the pfe secure boot header address. Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-06configs: Resync with savedefconfigTom Rini1-4/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-04dm: arm64: ls1012a: add i2c DM supportBiwen Li1-0/+3
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1012A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-02-04configs: ls1012ardb: Enable CONFIG_SYS_RELOC_GD_ENV_ADDRKuldeep Singh1-0/+1
Enable the config for ls1012ardb as the entry got missed earlier. Fixes: 8d8ee47e03 ("env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol") Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-24configs: fsl-layerscape: secure_boot: Enable setexpr commandUdit Agarwal1-1/+1
setexpr command is used while running secure boot (chain of trust with confidentiality) feature. Enable CONFIG_CMD_SETEXPR to enable setexpr command. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-05configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04mtd: ensure MTD is compiled when there is a SPI NOR flash using MTDMiquel Raynal1-0/+1
MTD must be enabled when there is a SPI NOR flash using the SPI_FLASH_MTD config entry. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-21env: Finish migration of common ENV optionsTom Rini1-0/+1
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-11Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini1-1/+1
- Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC. - Few bug fixes and updates related to SPI, hwconfig, ethernet, fsl-layerscape, pci, icid, PSCI
2019-11-08freescale/layerscape: Rename the config CONFIG_SECURE_BOOT nameUdit Agarwal1-1/+1
Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC to avoid conflict with UEFI secure boot. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08configs: Resync with savedefconfigTom Rini1-2/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-14configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-19configs: Unset CONFIG_SPI_FLASH_BAR, move CONFIG_FSL_QSPI to defconfigAshish Kumar1-0/+2
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-04-30configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-08configs: Resync with savedefconfigTom Rini1-5/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-07armv8: ls1012ardb: Add TFABOOT supportRajesh Bhagat1-0/+59
TFABOOT support includes: - ls1012ardb_tfa_defconfig to be loaded by trusted firmware - environment address and size changes for TFABOOT - define BOOTCOMMAND for TFABOOT - enable PFE validation for secure boot Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Signed-off-by: Pankit Garg <pankit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-05 18:09:37 +0300