Age | Commit message (Collapse) | Author | Files | Lines |
|
CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes
that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child
nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be
differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and
this is something that we have to avoid:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
After this patch:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1
Before the patch:
=> i2c bus
Bus 0: i2c@600
Bus 0: i2c@600 (active 0)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>
After the patch:
=> i2c bus
Bus 0: i2c@600
Bus 1: i2c@600 (active 1)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rewrite the CONFIG_BOOTCOMMAND only if it's not previously configured from
defconfig file.
This allows the user to select from defconfig/menuconfig the desired
boot command.
Adjust the current board defconfigs to reflect the default booting command
for the specific ENV configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
Prepare v2021.07-rc5
# gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]
# Conflicts:
# configs/am64x_evm_r5_defconfig
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
|
|
Add hash and hash verify commands. These would be useful for
verifying copied data.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add drivers for flexcom, i2c and eeproms
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Add new config for storing environment from sdmmc0.
Also clean-up sama7g5ek_emmc1 to point to the proper mmc device.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Enable CCF for SAMA7G5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Enable support for KSZ9131.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Enable mii command as ethernet's PHY specific programming is
based on it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Enable autoboot.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Use PIT64B driver. ATMEL_PIT is not available for SAMA7G5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Enable CONFIG_CPU.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Enable PLL driver for SAMA7G5.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Set malloc pool to 68K for sama7g5ek.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
|
|
Add initial support for sama7g5 evaluation kit board.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|