Age | Commit message (Collapse) | Author | Files | Lines |
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_CBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_PBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
Now that the k210 clock driver does not depend on CCF, we should no longer
imply it (and probably should not have in the first place). We can also
reduce the pre-relocation malloc arena back to something sensible.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
Linux has had some stability issues when using AISRAM with a different
frequency from SRAM. Mirror their change here now that we relocate into
AISRAM.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
|
|
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|
|
This enables configs necessary for using SPI. The environment is saved to
the very end of SPI flash. This is unlikely to be overwritten unless the
entire flash is reprogrammed.
This also supplies a default bootcommand. It loads an image and device tree
from the first partition of the MMC. This is a minimal/least effort
bootcmd, so suggestions (especially in the form of patches) are welcome. I
didn't set up distro boot because I think it is unlikely that any
general-purpose linux distros will ever be ported to this board.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Chrstopher Obbard <obbardc@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
The K210 has only 8 MiB RAM thereof 2 MiB reserved for AI.
Allow only 1 MiB for the stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Sipeed Maix series is a collection of boards built around the RISC-V
Kendryte K210 processor. This processor contains several peripherals to
accelerate neural network processing and other "ai" tasks. This includes a
"KPU" neural network processor, an audio processor supporting beamforming
reception, and a digital video port supporting capture and output at VGA
resolution. Other peripherals include 8M of sram (accessible with and
without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
peripherals vary, but include spi flash; on-board usb-serial bridges; ports
for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
similar.
Documentation for Maix boards is located at
<http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
located at <https://kendryte.com/downloads/>. However, hardware details are
rather lacking, so most technical reference has been taken from the
standalone sdk located at
<https://github.com/kendryte/kendryte-standalone-sdk>.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
|