summaryrefslogtreecommitdiff
path: root/configs/turris_omnia_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2023-02-17configs: Resync with savedefconfigTom Rini1-3/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-10-31Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass1-1/+1
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-06arm: mvebu: turris_omnia: Specify VHV gpio for eFUSE programmingPali Rohár1-0/+2
VHV gpio is connected to MCU and only on updated board design. Without it eFUSE programming does not work. Omnia MCU driver exports this GPIO to U-Boot under name mcu_56 and only when it is supported by MCU. So U-Boot fuse command refuse eFUSE programming on older board design when VHV gpio is not available. We tested that Armada 385 without connected VHV gpio can do eFUSE programming but only for some bits and only sometimes - it is unstable. And better to be disabled on older board design without VHV gpio support. Signed-off-by: Pali Rohár <pali@kernel.org>
2022-09-20arm: mvebu: turris_omnia: Add CONFIG_BOARD_SIZE_LIMITPali Rohár1-0/+2
Maximal size of u-boot kwb image binary is $CONFIG_ENV_OFFSET which is 0xF0000 = 983040 bytes. So add missing CONFIG_BOARD_SIZE_LIMIT definition to ensure that u-boot binary does not overflow to the u-boot env storage. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-09-13arm: mvebu: turris_omnia: Allow to use second serial portPali Rohár1-0/+2
Turris Omnia has two serial ports. Both are already specified in device tree file. But U-Boot by default does not allow to use more than one serial port unless CONFIG_SERIAL_PROBE_ALL is not enabled. After enabling CONFIG_SERIAL_PROBE_ALL, U-Boot see also second serial port (but is inactive by default): => coninfo List of available devices: serial@12000 00000007 IO stdin stdout stderr serial@12100 00000007 IO To allow simultaneously to use more input / output devices it is needed to enable CONFIG_CONSOLE_MUX option. With CONFIG_CONSOLE_MUX it is possible to call: => setenv stdout 'serial@12000,serial@12100' And U-Boot output is then visible on both serial ports. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-08-23configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-09arm: mvebu: turris_omnia: Add Winbond SPI flash supportMarek Behún1-0/+1
Some new Omnia boards will come with Winbond SPI flash. Add to defconfig. Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-07-29arm: mvebu: turris_omnia: Enable a38x pinctrl and gpio supportPali Rohár1-1/+2
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-07-26configs: Resync with savedefconfigTom Rini1-1/+0
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-21arm: mvebu: turris_omnia: Set ETHPRIME to DT aliasPali Rohár1-1/+1
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN ethernet port. This removes hardcoded DT node name from U-Boot configuration file. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <kabel@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_STACK to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini1-0/+2
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_MAXARGS to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-17arm: mvebu: turris_{omnia,mox}: Enable CONFIG_NETCONSOLEPali Rohár1-0/+1
This allows to use U-Boot console on Turris devices via network. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-17arm: mvebu: turris_omnia: Fix DEBUG_UART_BASEPali Rohár1-1/+2
Internal registers in SPL are at address 0xd0000000 and in proper U-Boot at address 0xf1000000. UART base address is located in internal registers. Fix DEBUG_UART_BASE option to correct value for both SPL and proper U-Boot. This change fixes hangup of proper U-Boot when it is trying to print something via debug UART. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04net: mvneta: Convert to use PHY_FIXED for fixed-linkMarek Behún1-0/+1
Stop parsing fixed-link in the MAC driver. Instead support only PHY mode and let the fixed PHY driver handle the fixed-link case. Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and ESPRESSObin. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-04net: mvneta: Use DM MDIO API for connecting PHYMarek Behún1-0/+1
Use the modern DM MDIO API for connecting PHY in the mvneta driver. This requires enabling MVMDIO driver in several config files. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2022-05-02arm: mvebu: turris_omnia: Define CONFIG_ETHPRIME instead of ethact= ENVPali Rohár1-0/+2
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact stores currently active ethernet device. So there is no point to set ethact= in default environment. Instead set CONFIG_ETHPRIME properly. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz>
2022-05-02arm: mvebu: turris_omnia: Enable ENV support in SPLPali Rohár1-0/+1
Allow to read ENV variables also in SPL on Turris Omnia. Signed-off-by: Pali Rohár <pali@kernel.org>
2022-04-21arm: mvebu: turris_omnia: Enable CONFIG_CMD_FUSEPali Rohár1-0/+2
This allows to read eFuse on Turris Omnia. Signed-off-by: Pali Rohár <pali@kernel.org>
2022-04-20Kconfig: Change SYS_MALLOC_F_LEN default to 0x2000Tom Rini1-1/+0
The most commonly used value today is 0x2000 and not 0x400. Rework the Kconfig logic to use this more frequently used value as the default. Cc: Andrew F. Davis <afd@ti.com> Cc: Alex Nemirovsky <alex.nemirovsky@cortina-access.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Alison Wang <alison.wang@nxp.com> Cc: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com> Cc: Andes <uboot@andestech.com> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Bharat Gooty <bharat.gooty@broadcom.com> Cc: David Lechner <david@lechnology.com> Cc: Dzmitry Sankouski <dsankouski@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@gmail.com> Cc: Eugeniy Paltsev <paltsev@synopsys.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Gerald Kerma <dreagle@doukki.net> Cc: Gregory CLEMENT <gregory.clement@bootlin.com> Cc: Holger Brunck <holger.brunck@hitachienergy.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Jassi Brar <jaswinder.singh@linaro.org> Cc: Kristian Amlie <kristian.amlie@northern.tech> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Liviu Dudau <liviu.dudau@foss.arm.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Lukasz Majewski <lukma@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Masami Hiramatsu <masami.hiramatsu@linaro.org> Cc: Matthias Brugger <mbrugger@suse.com> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: Michael Walle <michael@walle.cc> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Paul Kocialkowski <contact@paulk.fr> Cc: Priyanka Jain <priyanka.jain@nxp.com> Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com> Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Bosch <stefan_b@posteo.net> Cc: Stephan Gerhold <stephan@gerhold.net> Cc: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org> Cc: Thomas Weber <weber@corscience.de> Cc: Tony Dinh <mibodhi@gmail.com> Cc: Trevor Woerner <twoerner@gmail.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: liuhao <liuhao@phytium.com.cn> Cc: lixinde <lixinde@phytium.com.cn> Cc: shuyiqi <shuyiqi@phytium.com.cn> Cc: weichangzheng <weichangzheng@phytium.com.cn> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org> Reviewed-by: Tony Dinh <mibodhi@gmail.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> Reviewed-by: Kristian Amlie <kristian.amlie@northern.tech>
2022-04-08configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_NET_RETRY_COUNT to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_NET_RETRY_COUNT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18Convert CONFIG_ARP_TIMEOUT to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_ARP_TIMEOUT Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-04arm: mvebu: turris_omnia: Enable ext4 write support in defconfigMarek Behún1-0/+1
Enable ext4 write support in Turris Omnia's defconfig. Some users find it useful. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
2022-02-17arm: mvebu: turris_omnia: Reset the board immediately on DDR training failureMarek Behún1-0/+1
The state of the current DDR training code for Armada 38x is such that we cannot be sure it will always train successfully - although after the last change we were yet unable to find a board that failed DDR training, from experience in the last 2 years we know that it is possible. The experience also tells us that in many cases the board fails training only sometimes, and after a reset the training is successful. Enable the new option that makes the board reset itself on DDR training failure immediately. Until now we called hang() in such a case, which meant that the board was reset by the MCU after 120 seconds. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Pali Rohár <pali@kernel.org>
2022-02-11nvme: Split out PCI supportMark Kettenis1-1/+1
Apple SoCs have an integrated NVMe controller that isn't connected over a PCIe bus. In preparation for adding support for this NVMe controller, split out the PCI support into its own file. This file is selected through a new CONFIG_NVME_PCI Kconfig option, so do a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested on: Macbook Air M1 Tested-by: Simon Glass <sjg@chromium.org>
2022-01-20arm: mvebu: turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blobPali Rohár1-0/+1
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether it works in SATA or PCIe mode is determined by a strapping pin, which value is read from the MCU. We already determine which type of card is connected when configuring SerDeses. But until now we left both SATA and PCIe port 0 nodes in device tree enabled, and so the SATA driver is probed in U-Boot / Linux even if we know there is no mSATA card, and similarly PCIe driver tries to link on port 0 even if we know there is mSATA card, not a PCIe card. Fixup device tree blob to disable SATA node if mSATA card is not present, and to disable PCIe port 0 node if mSATA card is present. Do this for U-Boot's DT blob before relocation and also for kernel DT blob before booting. This ensures that software does not try to use SATA or PCIe HW when corresponding PHY is not configured. Signed-off-by: Pali Rohár <pali@kernel.org> [ refactored and fixed some issues ] Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
2021-12-27Convert CONFIG_ENV_SPI_BUS et al to KconfigTom Rini1-3/+0
This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE As part of this, we use Kconfig to provide the defaults now that were done in include/spi_flash.h. We also in some cases change from using CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in use anyhow as ENV was not enabled. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-15configs: Resync with savedefconfigTom Rini1-1/+0
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-16Merge tag 'v2021.10-rc4' into nextTom Rini1-0/+3
Prepare v2021.10-rc4 Signed-off-by: Tom Rini <trini@konsulko.com> # gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT # gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C # gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate] # Conflicts: # board/Arcturus/ucp1020/spl.c # cmd/mvebu/Kconfig # common/Kconfig.boot # common/image-fit.c # configs/UCP1020_defconfig # configs/sifive_unmatched_defconfig # drivers/pci/Kconfig # include/configs/UCP1020.h # include/configs/sifive-unmatched.h # lib/Makefile # scripts/config_whitelist.txt
2021-09-10arm: mvebu: turris_{omnia, mox}: GPT partition supportPali Rohár1-0/+1
This allows U-Boot to access filesystems on GPT partitioned disks. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-04serial: Rename SERIAL_SUPPORT to SERIALSimon Glass1-1/+1
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-01arm: mvebu: turris_omnia: disable MCU watchdog in SPL when booting over UARTMarek Behún1-0/+1
When booting over UART, sending U-Boot proper may take too much time and MCU watchdog will reset the board before U-Boot proper is loaded. Better disable MCU watchdog in SPL when booting over UART. Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-01arm: mvebu: turris_omnia: Enable NVMe supportPali Rohár1-0/+1
PCIe-based NVMe SSD disks in M.2 2230/2242/2260 form-factor can be connected to Turris Omnia mPCIe slot via passive M.2 <--> mPCIe adapter. So enable PCIe NVMe drivers. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-01Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini1-0/+1
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-07-31arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage headerPali Rohár1-1/+0
Now that proper load and execution addresses are set in v1 kwbimage we can use it for loading and booting U-Boot proper. Use the new spl_parse_board_header() function to implement parsing the kwbimage v1 header. Use information from this header to locate offset and size of the U-Boot proper binary, instead of using the legacy U-Boot header which is prepended to the U-Boot proper binary stored at fixed offset. This has the advantage that we do not need to relay on legacy U-Boot header anymore and therefore U-Boot proper binary can be stored at any offset, as is the case when loading & booting U-Boot proper by BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL code anymore. Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case BootROM is used for loading and executing U-Boot proper. This reduces the size of U-Boot's SPL image. By default these config options are enabled and so BootROM loading is not used. In some cases BootROM reads from SPI NOR at lower speed than U-Boot SPL. So people can decide whether they want to have smaller SPL binary at the cost of slower boot. Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO, CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT, CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply" (which can be selectivelly turned off and causes booting via BootROM). Options CONFIG_SYS_SPI_U_BOOT_OFFS, CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to zero as they define the location where kwbimage header starts. It is the location where BootROM expects start of the kwbimage from which it reads, parses and executes SPL part. The same applies to option CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one. Update all config files to set correct values of these options and set CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot proper starts. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-28i2c: Rename SPL/TPL_I2C_SUPPORT to I2CSimon Glass1-1/+1
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28Rename GPIO_SUPPORT to GPIOSimon Glass1-1/+1
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-27configs: Resync with savedefconfigTom Rini1-4/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-19arm: mvebu: turris_omnia: fixup MTD partitions in Linux' DTBMarek Behún1-0/+1
Fixup SPI NOR partition nodes in Linux' device tree prior booting Linux. Linux' devicetree does not contain "u-boot-env" partition and we do not want to add it there because the address is different between stock U-Boot and current upstream U-Boot. Instead we add code that recreates partition nodes from scratch according to how U-Boot sees them (which is defined in U-Boot's device tree). Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-15arm: mvebu: turris_{omnia, mox}: enable MTD commandMarek Behún1-0/+4
Now that the MTD subsystem properly supports OF partitions of a SPI NOR, we can enable the MTD command and start using it instead of the deprecated sf command. Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-07-15arm: mvebu: turris_omnia: force 40 MHz speed on SPI NORMarek Behún1-1/+3
Commit e2e95e5e2542 ("spi: Update speed/mode on change") changed the boot time on Turris Omnia from ~2.3s to over 8s, due to SPL loading main U-Boot from SPI NOR at 1 MHz instead of 40 MHz. This is because the SPL code passes the CONFIG_SF_DEFAULT_SPEED option to spi_flash_probe(), and with the above commit spi_flash_probe() starts prefering this parameter instead of the one specified in device-tree. The proper solution here would probably be to fix the SF subsystem to prefer the frequency specified in the device-tree, if it is present, but I am not sure what else will be affected on other boards with such a change. So until then we need a more simple fix. Since the CONFIG_SF_DEFAULT_SPEED option is used by the code, put the correct value there for Turris Omnia. Also put the correct value to CONFIG_SF_DEFAULT_MODE and use 40 MHz when reading environment. Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2021-06-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-25 05:51:37 +0300