summaryrefslogtreecommitdiff
path: root/configs/uniphier_v8_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2020-08-10configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-11ARM: uniphier: remove support for NOR Flash on support cardMasahiro Yamada1-3/+0
I actually do not see this used these days because eMMC or NAND is used for non-volatile devices. Dump the burden to maintain this crappy code. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-05-26configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-22ARM: uniphier: select DM_ETHMasahiro Yamada1-1/+0
drivers/net/smc911x.c has been converted to DM. select DM_ETH to enable it for all the UniPhier platform boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-27ARM: uniphier: enable CONFIG_MMC_HS400_SUPPORT for uniphier_v8_defconfigMasahiro Yamada1-1/+1
The eMMC controller on LD20 or later supports HS-400 mode. It works on a quick test. Enable it in case somebody may want to use it. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-02-27ARM: uniphier: enable CONFIG_MMC_SDHCI_ADMA for uniphier_v8_defconfigMasahiro Yamada1-1/+1
Switch over to ADMA from SDMA. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-08uniphier_{v7, v8}_defconfig: enable SPI driver and sspi commandMasahiro Yamada1-0/+4
Compile drivers/spi/uniphier_spi.c and cmd/spi.c Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-12-05configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flashMiquel Raynal1-0/+1
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NANDMiquel Raynal1-1/+1
Add more clarity by changing the Kconfig entry name. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-21env: Finish migration of common ENV optionsTom Rini1-0/+1
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini1-0/+1
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-10ARM: uniphier_v8_defconfig: make 64bit SoC image position independentMasahiro Yamada1-1/+3
For a planned new SoC in this SoC family, the base address of the DRAM will be changed from 0x80000000 to 0x20000000. The PIE support will be useful to maintain multiple similar SoCs whose DRAM addresses differ. Now CONFIG_SYS_TEXT_BASE is not important. I just set it to 0 to ensure CONFIG_POSITION_INDEPENDENT is working. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan1-0/+1
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-04-30configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-17ARM: uniphier_v8: enable CONFIG_SUPPORT_EMMC_RPMBMasahiro Yamada1-0/+1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-02-23preboot: Introduce CONFIG_USE_PREBOOT and migrate CONFIG_PREBOOTMasahiro Yamada1-0/+2
This is the same migration path as commit b6251db8c3f0 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND"). I also moved the description in README to the Kconfig help. I ripped off the sentence about 'LWMON' since it is gone already. I only let my boards migrate, leaving the rest to platform maintainers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-01-08configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-29ARM: uniphier: allow to source boot script before distro-bootMasahiro Yamada1-1/+1
Some users might need additional setups before booting the kernel. If there is found a file 'boot.scr', run it before invoking the distro boot command. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29ARM: uniphier: do not modify bootcmd environment variable at run-timeMasahiro Yamada1-0/+1
Some users might want to modify 'bootcmd' at compile-time by editing include/configs/uniphier.h, but overwriting it at run-time makes it impossible. Instead, set 'bootdev' at run-time, which contains the boot device the system is booting from, then indirectly reference it from 'bootcmd'. It is up to users whether to override 'bootcmd'. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-11-14configs: Migrate and re-enabled CONFIG_CMD_MTDPARTSTom Rini1-0/+1
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-20Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford1-0/+2
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini1-0/+1
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-08configs: Resync with savedefconfigTom Rini1-6/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-25ARM: uniphier: enable MTD partition and UBIMasahiro Yamada1-1/+4
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to use UBI on NAND devices. Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because enabling UBI would increase 170KB, which would be memory footprint problem. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-23Convert CONFIG_MTD_PARTITIONS et al to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_MTD_PARTITIONS CONFIG_MTD_DEVICE Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-22ARM: uniphier: enable CONFIG_SNI_AVE and disable CONFIG_SMC911XMasahiro Yamada1-4/+2
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig. Disable the on-board SMC911x because it has not migrated to the driver model yet - it is not possible to enable DM and non-DM drivers at the same time. The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept because the on-chip ethernet driver for LD4, sLD8 is not supported yet. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-08ARM: uniphier: enable CONFIG_PINCONFMasahiro Yamada1-0/+1
Enable the pin configuration feature for UniPhier 64 bit SoCs. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-02-24Convert CONFIG_BOOTP_BOOTPATH et al to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-06cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGATuomas Tynkkynen1-1/+0
cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-01-28ARM: uniphier: enable HS200 support for uniphier_v8_defconfigMasahiro Yamada1-0/+1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-09ARM: uniphier: enable CONFIG_MMC_SDHCI_SDMA for ARMv8 SoCsMasahiro Yamada1-0/+1
I did not enable SDMA when I added sdhci-cadence support because LD20 boards are equipped with a large amount memory beyond 32 bit address range, but SDMA does not support the 64bit address. U-Boot relocates itself to the end of effectively available RAM. This would make the MMC enumeration fail because the buffer for EXT_CSD allocated in the stack would go too high, then SDMA would fail to transfer data. Recent SDHCI-compatible controllers support ADMA, but unfortunately U-Boot does not support ADMA. In the previous commit, I hided the DRAM area that exceeds the 32 bit address range. Now, I can enable CONFIG_MMC_SDHCI_SDMA. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-26Move CONFIG_PANIC_HANG to KconfigMasahiro Yamada1-0/+1
Freescale (NXP) boards have lots of defconfig files per board. I used "imply PANIC_HANG" for them. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-19configs: Resync with savedefconfigTom Rini1-2/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-28ARM: uniphier: set CONFIG_LOGLEVEL to 6Masahiro Yamada1-0/+1
Print out KERN_NOTICE or higher level log messages. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-21net: Add SMC911X driver to Kconfig, convertAdam Ford1-0/+4
We add the various SMC91XX symbols to drivers/net/Kconfig and then this converts the following to Kconfig: CONFIG_SMC911X CONFIG_SMC911X_BASE CONFIG_SMC911X_16_BIT CONFIG_SMC911X_32_BIT Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Apply to the rest of the tree, re-squash old and new patch] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-15ARM: uniphier: enable DWC3 xHCI driverMasahiro Yamada1-0/+2
Enable CONFIGs for the DWC3 core and the UniPhier specific glue layer. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-11cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen1-0/+1
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-09-02Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is setAdam Ford1-0/+1
Add the following options to drivers/misc/Kconfig: SYS_I2C_EEPROM_ADDR SYS_I2C_EEPROM_BUS SYS_EEPROM_SIZE SYS_EEPROM_PAGE_WRITE_BITS SYS_EEPROM_PAGE_WRITE_DELAY_MS SYS_I2C_EEPROM_ADDR_LEN SYS_I2C_EEPROM_ADDR_OVERFLOW This does not migrate any boards, but provides a foundations for those who want/need these options Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Migrate uniphier] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-30ARM: uniphier: enable Denali NAND driver for 64bit SoCsMasahiro Yamada1-0/+5
Now the entry to the NAND driver init can be is controlled by DT; it should not hurt to compile the driver all the time. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-15configs: Resync with savedefconfigTom Rini1-3/+3
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-26ARM: uniphier: enable CONFIG_CMD_FS_GENERICMasahiro Yamada1-0/+1
Enable file system commands such as load, ls. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-20ARM: uniphier: enable PSCI sysreset for uniphier_v8_defconfigMasahiro Yamada1-0/+3
This configuration is supposed to be used with ARM Trusted Firmware, so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of U-Boot's own reset code because we need to coordinate with SCP (System Control Processor) for the system-level power management. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-03-13configs: Re-syncTom Rini1-1/+1
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-23ARM: uniphier: enable CONFIG_CMD_CONFIGMasahiro Yamada1-0/+1
This command is useful to see which config options are enabled on the running U-Boot image. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23ARM: uniphier: enable CONFIG_CMD_GPTMasahiro Yamada1-0/+1
Enable CONFIG_CMD_GPT, keeping CONFIG_SPL_EFI_PARTITION because the SPL for UniPhier platform does not recognize any partitions. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-31 06:29:46 +0300