summaryrefslogtreecommitdiff
path: root/configs/warp7_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2021-12-01Convert CONFIG_USE_BOOTCOMMAND et al to KconfigTom Rini1-0/+2
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-15configs: Resync with savedefconfigTom Rini1-2/+1
Resync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-05lib: optee: Remove CONFIG_OPTEE_LOAD_ADDRAlexandru Gagniuc1-1/+0
This value is not used by u-boot, and it should not. The load address of an OPTEE image is defined by said image. Either a uImage or a FIT will have a defined load address and entry point. Those values are the correct ones, not CONFIG_OPTEE_LOAD_ADDR. Commit f25006b96e9f ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies this config by requiring its presence in u-boot's .config for other images as part of a larger build, claiming it is "the best way". This argument is not persuasive. U-boot's configuration is driven by platform requirements, not the other way around. It seems more likely that the argument is conflating tooling issues with Kconfig. Yocto and buildroot have excellent mechanisms for defining values across the board (pun intended). u-boot's Kconfig is the wrong place to do it. Furthermore, it is not "best" for u-boot because it hardcodes a value which is then not used. In fact the load address that u-boot uses is the one derived from the OPTEE image. Confused yet? I sure was. To prevent future confusion, remove CONFIG_OPTEE_LOAD_ADDR. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2021-10-05lib: optee: Remove CONFIG_OPTEE_TZDRAM_BASEAlexandru Gagniuc1-1/+0
It is no longer used in u-boot. Information about the TZDRAM location is usually available in the devicetree as "/reserved-memory/" nodes. Because this isn't used, remove it. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2021-09-07imx: Convert SERIAL_TAG support to ENV_VARS_UBOOT_RUNTIME_CONFIGTom Rini1-0/+1
No iMX platforms have supported ATAG-based booting. They have however re-used the CONFIG_SERIAL_TAG option as a way to enable support of reading the OTP fuses and setting the serial# environment variable in some cases. Change the warp7 support to use this symbol, use this for updating the rest of the imx7 code, and update the imx8 conditionals. Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-01imx: Finish migration of IMX_CONFIG to KconfigTom Rini1-1/+0
- Provide a default Kconfig value of the default script - Largely continue to define this via the board Kconfig file - For the boards that select a script based on defconfig rather than TARGET, keep this within the defconfig. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_MXC et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-27configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28Merge tag 'v2021.07-rc5' into nextTom Rini1-1/+1
Prepare v2021.07-rc5 # gpg: Signature made Mon 28 Jun 2021 03:39:36 PM EDT # gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C # gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate] # Conflicts: # configs/am64x_evm_r5_defconfig
2021-06-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-09usb: dfu: Migrate CONFIG_SYS_DFU_DATA_BUF_SIZE and ↵Aswath Govindraju1-0/+1
CONFIG_SYS_DFU_MAX_FILE_SIZE to Kconfig Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h files and also in <board_name>_defconfig files without a Kconfig option. It is easier for users to set these configs in defconfig files than in config header files as they are a part of the source code. Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py script. Suggested-by: Pratyush Yadav <p.yadav@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Matthias Brugger <mbrugger@suse.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2021-05-11configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-12-07configs: migrate CONFIG_IMX_THERMAL to defconfigsTom Rini1-0/+1
Done via moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-11-30configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-08-10configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-17Convert CONFIG_MXC_UART to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_MXC_UART Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-07-06configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma1-0/+2
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-09Merge tag 'u-boot-imx-20191209' of ↵Tom Rini1-1/+1
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.01 ----------------- - imx8qxp_mek: increase buffer sizes and args number - Fixes for imx7ulp - imx8mm: Fix the first root clock in imx8mm_ahb_sels[] - colibri_imx7: reserve DDR memory for Cortex-M4 - vining2000: fixes and convert to ethernet DM - imx8m: fix rom version check to unbreak some B0 chips - tbs2910: Disable VxWorks image booting support
2019-12-06warp7: Fix U-Boot corruption after saving the environmentFabio Estevam1-1/+1
U-Boot binary has grown in such a way that it goes beyond the reserved area for the environment variables. Running "saveenv" followed by a "reset" causes U-Boot to hang because of this overlap. Fix this problem by increasing the CONFIG_ENV_OFFSET size. Also, in order to prevent this same problem in the future, use CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time. CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare CONFIG_ENV_OFFSET with its direct value instead. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Pierre-Jean Texier <pjtexier@koncepto.io> Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io> Acked-by: Joris Offouga <offougajoris@gmail.com> Tested-by: Joris Offouga <offougajoris@gmail.com>
2019-12-04mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTDMiquel Raynal1-0/+1
Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-21env: Finish migration of common ENV optionsTom Rini1-0/+2
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini1-0/+1
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-08configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-08imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HABStefano Babic1-1/+1
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross architecture purposes. If Secure Boot is required for imx, this means to enable and use the HAB processor in the soc. Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-08-23Convert CONFIG_FSL_USDHC to KconfigAdam Ford1-1/+1
This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-23Convert to use fsl_esdhc_imx for i.MX platformsYangbo Lu1-1/+1
Converted to use fsl_esdhc_imx for i.MX platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Martyn Welch <martyn.welch@collabora.com> Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-05-04Convert CONFIG_SUPPORT_EMMC_BOOT to KconfigAlex Kiernan1-0/+1
This converts the following to Kconfig: CONFIG_SUPPORT_EMMC_BOOT As requested by Michal Simek <michal.simek@xilinx.com>, these boards have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated: xilinx_zynqmp_zc1275_revB xilinx_zynqmp_zc1751_xm018_dc4 xilinx_zynqmp_zc1751_xm019_dc5 xilinx_zynqmp_zcu100_revC xilinx_zynqmp_zcu102_rev1_0 xilinx_zynqmp_zcu102_revA xilinx_zynqmp_zcu102_revB xilinx_zynqmp_zcu104_revA xilinx_zynqmp_zcu104_revC xilinx_zynqmp_zcu106_revA xilinx_zynqmp_zcu111_revA Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Lukasz Majewski <lukma@denx.de> Acked-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Ramon Fried <ramon.fried@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-01Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imxTom Rini1-0/+3
Porting to DM and i.MX8 ------------------------ - warp7 to DM - kp_imx53 to DM - Warnings in DT - MX8QM support - colibri-imx6ull to DM - imx7d-pico to DM - ocotp for MX8
2019-04-30configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-25warp7: Switch to DM USBPierre-Jean Texier1-0/+1
This commit switches to DM USB for warp7 and warp7_bl33 defconfigs. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-04-25warp7: Switch to DM SerialPierre-Jean Texier1-0/+2
This commit switches to DM SERIAL for warp7 and warp7_bl33 defconfigs. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io> Signed-off-by: Joris Offouga <offougajoris@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-02-07configs: Resync with savedefconfigTom Rini1-13/+12
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-28arm: imx7s-warp: Convert to DM PMICBryan O'Donoghue1-0/+6
This patch converts the warp7 and warp7_bl33 board ports over to using the DM PMIC model. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28warp7: defconfig: Switch to DM for I2CBryan O'Donoghue1-0/+1
This commit switches to DM I2C for warp7 and warp7_bl33 defconfigs. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28warp7: defconfig: Switch on IMX7 GPIO/pinctrl for both portsBryan O'Donoghue1-0/+3
Switches on the IMX7 pinctrl driver for the warp7 and warp7_bl33 ports, necessary to convert over to DM for this board. It is necessary to switch on pinctrl and GPIO in one go. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28arm: imx7s-warp: Convert to DM MMC initializationBryan O'Donoghue1-0/+1
Converts from fixed initialization of MMC to DM initialization of MMC. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-28arm: imx7s-warp: Add DT file hooksBryan O'Donoghue1-1/+2
This patch adds DT file hooks for imx7s-warp.dtb to the warp7 and warp7_bl33 builds. Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Peng Fan <peng.fan@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2019-01-19Kconfig: Migrate BOUNCE_BUFFERPhilipp Tomsich1-0/+1
The bounce buffer is used by a few drivers (most of the MMC drivers) to overcome limitations in their respective DMA implementation. This moves the configuration to Kconfig and makes it user-selectable (even though it will be a required feature to make those drivers work): the expected usage is for drivers depending on this to 'select' it unconditionally from their respective Kconfig (see follow-up patches). This commit includes a full migration using moveconfig.py to ensure that each commit compiles. To ensure bisectability we update dependencies of various drivers to now select BOUNCE_BUFFER when needed. [trini: Squash all patches to ensure bisectability] Signed-off-by: Tom Rini <trini@konsulko.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion] Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion] Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
2018-12-17warp7: configs: add CONFIG_FIT optionPierre-Jean Texier1-0/+2
This enable FIT image support. Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
2018-11-14configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-22optee: adjust dependencies and default values for dramRui Miguel Silva1-0/+2
We may have, the not yet considered, scenario where OPTEE is loaded before u-boot and *not* by u-boot, e.g, the boot flow using the ARM Trusted Firmware (ATF), where in the 32bit flow is: BootRom->ATF(BL2)->Optee(BL32)->u-boot(BL33) In this case we need still to reserve the memory used by optee, to avoid for example to realocate ourself to the same address at the end of DRAM. So, we change here the dependencies on the OPTEE lib and we set the default size and base of TZRAM to zero. Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Ryan Harkin <ryan.harkin@linaro.org> Cc: u-boot@lists.denx.de
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini1-0/+1
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-08configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-16 10:32:03 +0300