Age | Commit message (Collapse) | Author | Files | Lines |
|
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
Sheevaplug board has 512K CONFIG_BOARD_SIZE_LIMIT. Recently, DM_SERIAL has
pushed the image size a few hundred bytes over that limit. So explicitly
deselect some configs that are unrelated to this board
(and gain back a bit over 2K).
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
|
|
Thecus N2350 is a NAS based on Marvell Armada 385 SoC.
Specification:
- Processor: Marvel MV88F6820 Dual Core at 1GHz
- 1 GiB DDR4 RAM
- 4MB Macronix mx25l3205d SPI flash
- 512MB Hynix H27U4G8F2DTR-BC NAND flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 2x SATA (hot swap slots)
- 3x buttons
- 10x LEDS
- serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
https://source.denx.de/u-boot/custodians/u-boot-mpc8xx
- A fix for a long standing bug that has been exposed by commit
50128aeb0f8 ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
|
|
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
|
|
version
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
|
|
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
|
|
Remove ns16550 configuration from header files. Document
DM_SERIAL-required prior stage device tree configuration.
|
|
as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file
board/socrates/socrates.env
which contains the default environment. While at it,
cleanup the default Environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
As explained by Philippe Schenker, I was misinterpreting what happened
in the case where we do not set LMB_USE_MAX_REGIONS and so had
re-introduced the problem I was attempting to more widely resolve.
This reverts commit 007ae5d108a37564905ea1588cb279f3a522cc3d.
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
These are only used in one place, so move them there.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
am335x_evm_defconfig is used for BeagleBone Black, popular single board
computer with wide extension support. Enable CONFIG_CMD_EXTENSION by default
since extension detection is already implemented for am335x.
Also run make savedefconfig for am335x_evm_defconfig
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
|
|
allow only to boot signed fitimages (and signed u-boot
scripts).
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
enable protected Environment on socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add autoboot delay string for socrates board.
use sha256 for abort autoboot, use "ao" to abort.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add support for i2c eeprom on address 0x51.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add boot retry feature and reboot after 120 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
drop second flash bank, as not used anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
setup MTD partitioning through mtdparts variable
and set it to:
mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)
and pass this to linux per kernel commandline.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
current mainline does not work on socrates board. To
get it back up working, there are some updates needed
in socrates_defconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixes: 94633c36f9eb ("net: Make DM_ETH be selected by NETDEVICE")
Fixes: 2f8a6db5d83b ("Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig")
|
|
The LMB code allows for picking a hard limit on the number of regions it
can know of, or to dynamically allocate these regions. The reason for
this choice is to allow for the compiler to perform a size optimization
in the common case. This optimization however, is very small, ranging
from 196 bytes to 15 bytes saved, or in some cases, being larger. Now
that we also have more regions covered by LMB (in order to protect
various parts of our self at run time), the default of 8 is also much
easier to hit and leads to non-obvious error messages (which imply that
an area is protected, not that we're out of areas to add to the list).
Switch to the dynamic use as the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2023.04
-----------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15028
- Boards:
- UDoo
- MX53 Menlo
|
|
Convert to DM_SERIAL and drop the iomux board file
level init as it's handled as part of the DM serial
layer instead.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
This moves over the PMIC power init to DM and the associated i2c and
regulator bits.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
Convert the board from legacy serial code to DM SERIAL.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
Add MV88E61XX DSA support:
- update dt to provide internal MDIO bus and port handles.
U-Boot requires a more restrictive subset of the dt bindings
required by Linux for the sake of simplifying code
- update defconfig to remove old driver and enable new one
- replace mv88e61xx_hw_reset weak override with board_phy_config support
for register configuration that is outside the scope of the DSA driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
|
|
Enable I2C support on D3 Draak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
|
|
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2023.04
-----------
- several conversion to DM_SERIAL and DM_I2C
- fixes for Toradex boards
- PSCI
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/14965
|
|
Add the needed DT overrides and configs to enable UART in SPL.
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
The imx8mn-beacon SOM has a QSPI part on it connected to the
FlexSPI controller. Add a defconfig option which supports
booting from the QSPI NOR flash instead of sd/mmc.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Convert to DM_I2C
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Convert to DM_I2C
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-amlogic
- jethub j100: add rescue boot from microSD
- move meson sm command to cmd/meson and add efusedump sub-command
- switch dwc2 otg to DM for G12A, GXL & AXG
- Add new boards:
- Odroid Go Ultra
- Odroid-N2L
|
|
SPI NAND read access
The introduction of CONFIG_FSL_QSPI_AHB_FULL_MAP as default in:
def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX")
broke the SPI NAND read access on the Kontron SL i.MX6UL/ULL boards.
Reading data from the flash returns garbage instead of the actual
content. Fix this for now by disabling the introduced option.
In the long run this should be fixed globally.
Fixes: def88bce094e ("spi: fsl_qspi: Support to use full AHB space on i.MX")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Select DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
The conversion to DM_I2C is mandatory, so convert to it
and also to DM_PMIC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
The conversion to CONFIG_DM_SERIAL is mandatory, so select
this option.
Signed-off-by: Fabio Estevam <festevam@denx.de>
|
|
These SoMs may ship with SMSC LAN8740Ai PHYs, enable the SMSC PHY driver.
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
These SoMs never ship with Atheros PHYs, disable the Atheros PHY driver.
Signed-off-by: Marek Vasut <marex@denx.de>
|