summaryrefslogtreecommitdiff
path: root/include/configs/sunxi-common.h
AgeCommit message (Collapse)AuthorFilesLines
2023-01-21sunxi: h616: lower SPL stack address to avoid BROM dataAndre Przywara1-1/+1
When using the USB OTG FEL mode on the Allwinner H616, the BootROM stores some data at the end of SRAM C. This is also the location where we place the initial SPL stack, so it will overwrite this data. We still need the BROM code after running the SPL, so should leave that area alone. Interestingly this does not seem to have an adverse effect, I guess on the "way out" (when we return to FEL after the SPL has run), this data is not needed by the BROM, for just the trailing end of the USB operation. However this is still wrong, and we should not clobber BROM data. Lower the SPL stack address to be situated right below the swap buffers we use in sunxi-fel: that should be out of the way of everyone else. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org>
2022-12-23kbuild: Remove uncmd_spl logicTom Rini1-1/+1
At this point in the conversion there should be no need to have logic to disable some symbol during the SPL build as all symbols should have an SPL counterpart. The main real changes done here are that we now must make proper use of CONFIG_IS_ENABLED(DM_SERIAL) rather than many of the odd tricks we developed prior to CONFIG_IS_ENABLED() being available. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-23global: Migrate CONFIG_EXTRA_ENV_SETTINGS to CFGTom Rini1-1/+1
Perform a simple rename of CONFIG_EXTRA_ENV_SETTINGS to CFG_EXTRA_ENV_SETTINGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-22Convert CONFIG_STANDALONE_LOAD_ADDR to KconfigTom Rini1-3/+0
This converts the following to Kconfig: CONFIG_STANDALONE_LOAD_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-21Merge tag 'v2023.01-rc4' into nextTom Rini1-3/+0
Prepare v2023.01-rc4 Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-15sunxi: remove unused CONFIG_MMC_SUNXI_SLOTAndre Przywara1-3/+0
There is a CONFIG_MMC_SUNXI_SLOT definition in our sunxi_common.h config header, which was used to note the first MMC controller to initialise. The definition in that header was always set to 0, with no easy way of overriding this, and certainly none of the existing boards made any use of that (non-)feature. Remove that definition and replace it with a constant 0 in the only user, in board.c. It turns out that this is safe, as this is only used in the SPL, and the BROM also unconditionally initialises MMC0. This also removes the last legacy config symbol with SUN*I in it from the whitelist. Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-12-06global: Move remaining CONFIG_SYS_* to CFG_SYS_*Tom Rini1-2/+2
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-06global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*Tom Rini1-4/+4
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-06global: Move remaining CONFIG_SYS_NS16550_* to CFG_SYS_NS16550_*Tom Rini1-7/+7
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550 namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-12-06Convert CONFIG_SYS_NS16550_MEM32 et al to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SPL_NS16550_MIN_FUNCTIONS CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that platforms can enable the legacy driver here for SPL. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-06Convert CONFIG_SYS_NAND_MAX_OOBFREE et al to KconfigTom Rini1-4/+0
This converts the following to Kconfig: CONFIG_SYS_NAND_MAX_OOBFREE CONFIG_SYS_NAND_MAX_ECCPOS Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10Convert CONFIG_SYS_MONITOR_LEN to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10Convert CONFIG_SYS_MMC_MAX_DEVICE to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SYS_MMC_MAX_DEVICE Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-11-10Convert CONFIG_SYS_MAX_NAND_DEVICE to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_SYS_MAX_NAND_DEVICE Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-10-30video: Rename CONFIG_DM_VIDEO to CONFIG_VIDEOSimon Glass1-1/+1
Now that all the old code is gone, rename this option. Driver model migration is now complete. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-19sunxi: fix 32MB load address layoutAndre Przywara1-9/+9
The default load addresses for the various payloads (kernel, DT, ramdisk) on systems with just 32MB of DRAM have some issues: For a start the preceding comment doesn't match the actual values: apparently they were copied from the 64MB S3 layout, then halved, but since 0x5 is NOT the half of 0x10, they don't match up. Also those projected maximum sizes are quite restrictive: it's not easy to build a compressed kernel image with just 4MB. The only defconfig in mainline Linux that supports the F1C100s (the only 32MB user so far) creates a 6MB compressed / 15MB uncompressed kernel. Rearrange the default load addresses to accommodate such a kernel: we allow an 7MB/16MB kernel, and up to 5MB of ramdisk, stuffing the smaller binaries like the DTB towards the end, just before the relocated U-Boot. Shrink the size for DTB and scripts on the way, there is no need for allowing up to 512K for them. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-10-19sunxi: Kconfig: introduce SUNXI_MINIMUM_DRAM_MBAndre Przywara1-14/+17
Traditionally we assumed that every Allwinner board would come with at least 256 MB of DRAM, and set our DRAM layout accordingly. This affected both the default load addresses, but also U-Boot's own address expectations (like being loaded at 160 MB). Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So far we special-cased those *chips*, as there was only one chip per DRAM size. However new chips force us to take a more general approach. Introduce a Kconfig symbol, which provides the minimum DRAM size of the board. If nothing else is specified, we use 256 MB, and default to smaller values for those co-packaged SoCs. Then select the different DRAM maps according to this new symbol, so that different SoCs with the same DRAM size can share those definitions. Inspired by an idea from Icenowy. This is just refactoring: compiled for all boards before and after this patch: the binaries were identical. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-07-07Convert CONFIG_SYS_BOOTM_LEN to KconfigTom Rini1-4/+0
This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <smoch@web.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07Convert CONFIG_USB_OHCI_NEW et al to KconfigTom Rini1-5/+0
This converts the following to Kconfig: CONFIG_SYS_OHCI_SWAP_REG_ACCESS CONFIG_SYS_USB_OHCI_CPU_INIT CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS CONFIG_SYS_USB_OHCI_SLOT_NAME CONFIG_USB_ATMEL CONFIG_USB_ATMEL_CLK_SEL_PLLB CONFIG_USB_ATMEL_CLK_SEL_UPLL CONFIG_USB_OHCI_LPC32XX CONFIG_USB_OHCI_NEW Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-29Complete migration of MTDPARTS_DEFAULT / MTDIDS_DEFAULT, include in environmentTom Rini1-16/+0
- Ensure that everyone setting mtdids= and mtdparts= is doing so via the CONFIG options. - If the CONFIG options are set, ensure that the default environment sets mtdparts / mtdids. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-29Globally remove most CONFIG_SPL_BUILD tests from config headersTom Rini1-6/+0
With the exception of how PowerPC handles SPL and TPL (which has its own issues), we cannot safely hide options under CONFIG_SPL_BUILD. Largely remove the places that have this test today. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-29Convert CONFIG_LBA48 et al to KconfigTom Rini1-4/+0
This converts the following to Kconfig: CONFIG_LBA48 CONFIG_SYS_64BIT_LBA Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_START_ADDR to KconfigTom Rini1-3/+0
This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_STACK to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini1-5/+0
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_BSS_MAX_SIZE et al to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SPL_PAD_TO et al to KconfigTom Rini1-8/+0
This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_CBSIZE to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_SYS_CBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06Convert CONFIG_SYS_PBSIZE to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-21include/configs: drop COUNTER_FREQUENCYPeng Fan1-1/+0
Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-08Convert CONFIG_BOARD_SIZE_LIMIT to KconfigTom Rini1-9/+0
This converts the following to Kconfig: CONFIG_BOARD_SIZE_LIMIT To do this, introduce CONFIG_HAS_BOARD_SIZE_LIMIT. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18sunxi: Do not define CONFIG_SPL_STACK_ADDR_RTom Rini1-11/+0
We cannot define a CONFIG value here to ensure that the Kconfig value isn't set wrong. Fixes: 2c699fe0d34d ("configs: sunxi: Add common SUNIV header") Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-04configs: sunxi: Add common SUNIV headerIcenowy Zheng1-15/+42
Adds support for SUNIV and the F1C100s. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04sunxi-common.h: remove pointless #ifdefsAndre Przywara1-7/+0
Remove some pointless #ifdefs from this file, as there are quite too many of them already. Some definitions don't really hurt to have in any case, so remove the pointless CONFIG_MMC guard around CONFIG_MMC_SUNXI_SLOT. The BOARD_SIZE_LIMIT applies regardless of ARM64 or not (now), so remove that guard as well. The maximum number of MMC devices does not depend on CONFIG_ENV_IS_IN_MMC, so move that out to simplify the file. Last but not least CONFIG_SPL_BOARD_LOAD_IMAGE serves no real purpose anymore: it's unconditionally defined for all sunxi boards, and protects nothing applicable outside of sunxi code anymore. Just remove it. Reviewed-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-11-05Convert CONFIG_SPL_DRIVERS_MISC et al to KconfigTom Rini1-2/+0
This converts the following to Kconfig: CONFIG_SPL_DRIVERS_MISC CONFIG_SPL_ENV_SUPPORT CONFIG_SPL_GPIO CONFIG_SPL_I2C CONFIG_SPL_LDSCRIPT CONFIG_SPL_LIBCOMMON_SUPPORT CONFIG_SPL_LIBGENERIC_SUPPORT CONFIG_SPL_LOAD_FIT_ADDRESS CONFIG_SPL_MMC CONFIG_SPL_NAND_SUPPORT CONFIG_SPL_NO_CPU_SUPPORT CONFIG_SPL_OS_BOOT CONFIG_SPL_POWER CONFIG_SPL_STACK_R CONFIG_SPL_STACK_R_ADDR CONFIG_SPL_WATCHDOG CONFIG_SPL_TEXT_BASE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-12sunxi: video: Convert panel I2C to use DM_I2CSamuel Holland1-17/+0
Two displays supported by the sunxi display driver (each one used by a single board) require initialization over I2C. Both previously used i2c_soft; replace this with the i2c-gpio instance that already exists in those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus). Since the i2c-gpio nodes are not referenced by any other node in the device trees (the device trees have no panel node), the I2C bus is selected by its node name. This panel initialization code was the only i2c_soft user, so the i2c_soft GPIO setup code can be removed now as well. Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-06Convert CONFIG_SYS_NAND_ONFI_DETECTION to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_SYS_NAND_ONFI_DETECTION Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-08arm: Finish migration of CONFIG_MACH_TYPETom Rini1-16/+0
As this is only useful when booting with ATAGs, which are now largely disabled, remove this value for the remaining platforms. We have a few places in the code that had been testing for MACH_TYPE as a sort of internal logic. Update those to use different but still correct CONFIG symbols. Cc: Phil Sutter <phil@nwl.cc> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07arm: Disable ATAGs supportTom Rini1-5/+0
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and stemmy, disable ATAG support. A large number of platforms had enabled support but never supported a kernel so old as to require it. Further, some platforms are old enough to support both, but are well supported by devicetree booting, and have been for a number of years. This is because some of the ATAGs related functions have been re-used to provide the same kind of information, but for devicetree or just generally to inform the user. When needed still, rename these functions to get_board_revision() instead, to avoid conflicts. In other cases, these functions were simply unused, so drop them. Cc: Andre Przywara <andre.przywara@arm.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Phil Sutter <phil@nwl.cc> Cc: Stefan Bosch <stefan_b@posteo.net> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-01Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini1-8/+0
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-09-01Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini1-2/+0
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-30Convert CONFIG_SYS_I2C_SPEED et al to KconfigTom Rini1-9/+0
This converts the following to Kconfig: CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SLAVE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini1-1/+0
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_MVTWSI to KconfigTom Rini1-1/+0
This converts the following to Kconfig: CONFIG_SYS_I2C_MVTWSI Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_SOFT et al to KconfigTom Rini1-4/+1
This converts the following to Kconfig: CONFIG_SYS_I2C_SOFT CONFIG_SYS_I2C_SOFT_SPEED CONFIG_SYS_I2C_SOFT_SLAVE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-28i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACYSimon Glass1-1/+1
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less than a year away. Also we want to have a CONFIG_I2C for U-Boot proper just like we have CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules. Rename this symbol so it is clear it is going away. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-04-16sunxi: arm64: Add addresses for compressed kernel loadArnaud Ferraris1-0/+15
The "booti" command to load arm64 Linux kernels supports automatic decompression of zipped kernel images, but relies on some environment variables to point to usable buffer RAM. Add those variables and let them point to some default values, that should cover most use-cases. Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-04-16sunxi: add fdtoverlay_addr_r environment variableJernej Skrabec1-23/+26
Commit 69076dff2284 ("cmd: pxe: add support for FDT overlays") added support for loading DT overlay files to PXE boot. However, it needs additional environment variable which points to memory location which can be used to temporary store overlay data. Add it and in the process unify alignment using spaces and fix comment. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-03-03video: sunxi_display: Convert to DM_VIDEOJagan Teki1-22/+1
DM_VIDEO migration deadline is already expired, but around 80 Allwinner boards are still using video in a legacy way: ===================== WARNING ====================== This board does not use CONFIG_DM_VIDEO Please update the board to use CONFIG_DM_VIDEO before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Convert the legacy video driver over to the DM_VIDEO framework. This is a minimal conversion: it doesn't use the DT for finding its resources, nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS). Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan) Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> [Andre: rebase and smaller fixes] Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-21dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIOIgor Opaniuk1-1/+1
Use CONFIG_IS_ENABLED() macro, which provides more convenient way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs for both SPL and U-Boot proper. CONFIG_IS_ENABLED(DM_I2C) expands to: - 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y', - 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y', - 0 otherwise. All occurences were replaced automatically using these bash cmds: $ find . -type f -exec sed -i 's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + $ find . -type f -exec sed -i 's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + $ find . -type f -exec sed -i 's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-10-17 07:58:54 +0300