Age | Commit message (Collapse) | Author | Files | Lines |
|
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add chip select number check in spi_find_chip_select().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
|
|
At present we have to have an xfer() method even if it does nothing. This
is not correct, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Add support for SPI synchronous write followed by read,
this is common interface call from spi-nor to spi drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
|
|
This patch update the behavior introduced by
commit 96907c0fe50a ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Remove spi_init definition which never used on
respective code since from many years.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
A previous patch removed the spi_flash_probe_fdt function, which
contained the last call of the spi_setup_slave_fdt function, which is
now equally obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
0efc024 ("spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT
node") added a helper function spi_base_setup_slave_fdt to to set up a
SPI slave from a given FDT blob. The only user was the exynos SPI
driver.
But commit 73186c9 ("dm: exynos: Convert SPI to driver model") removed
the use of this function, hence rendering it obsolete.
Remove this function, as well as the CONFIG_OF_SPI option, which guarded
only this function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
option from spi_slave {} never used so drop the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Update the SPI uclass to support a live device tree. Also adjust
spi_slave_ofdata_to_platdata() to accept a device instead of a blob and
offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Dual flash code in spi are usually take the spi controller
to work with dual connected flash devices. Usually these
dual connection operation's are referred to flash controller
protocol rather with spi controller protocol, these are still
present in flash side for the usage of spi-nor controllers.
So, this patch remove the dual_flash options or flags in sf
which are triggered from spi controller side.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Removed SPI_RX_FAST since default read for spi slaves
are always 1-wire fast read.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Introduce dm_spi_claim_bus, dm_spi_release_bus and dm_spi_xfer
Convert spi_claim_bus, spi_release_bus and spi_xfer to use
the new API.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
spi bus can support dual and quad wire data transfers for tx and
rx. So defining dual and quad modes for both tx and rx. Also add
support to parse bus width used for spi tx and rx transfers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Added SPI_TX_DUAL mode flag.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SLOW, FAST, DUAL, DUAL_IO, QUAD, QUAD_IO changed order to
SLOW, FAST, DUAL, QUAD, DUAL_IO, QUAD_IO
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
- Add comments on mode_rx
- Tab space's
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Fixed bit assignment with flags members on spi_slave{}
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
This patch moves flags macro's to respective member
position on spi_slave{}, for better readabilty and
finding the respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SPI_OPM_RX_AS - SPI_RX_SLOW
SPI_OPM_RX_AF - SPI_RX_FAST
SPI_OPM_RX_DOUT - SPI_RX_DUAL
SPI_OPM_RX_QOF - SPI_RX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SPI_OPM_RX_DIO and SPI_OPM_RX_QIOF are rx IO
commands/opmodes for dual and quad. Usually IO
operation's are referred to flash protocol rather
with spi controller protocol, these are still present
in flash side for the usage of spi-nor controllers.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
SPI_OPM_RX_EXTN is a combination of all rx opmode's
and spi driver shall use any one of the rx mode at
a time not the combination and it is true in case of
flash where spi_flash_table mention combination of
supported read opmodes so-that the required one
will pick based on the rx mode from spi driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like
SPI_TX_BP => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Couldn't find the exact reason to define 'mode' for dm,
probably it is not using in non-dm drivers but it need
to visible both dm and non-dm as mode data is getting
dereferred in spi flash core ie common to both.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
- Adjust tab spaces
- Add comments
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
This comment should refer to SPI, not serial.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Only set the speed if it has changed from last time. Since the speed will
be 0 when the device is probed it will always be changed on the first
transfer after the device is probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Correct the macros as per insertion of array fast read
command CMD_READ_ARRAY_FAST in spi_read_cmds_array in file
sf_probe.c
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Enabled byte program support for sst flashes in sf.
Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.
A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
U-Boot includes a SPI emulation driver already but it is not explicit, and
is hidden in the SPI flash code.
Conceptually with sandbox's SPI implementation we have a layer which
creates SPI bus transitions and a layer which interprets them, currently
only for SPI flash. The latter is actually an emulation, and it should be
possible to add more than one emulation - not just SPI flash.
Add a SPI emulation uclass so that other emulations can be plugged in to
support different types of emulated devices on difference buses/chip
selects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Add a uclass which provides access to SPI buses and includes operations
required by SPI.
For a time driver model will need to co-exist with the legacy SPI interface
so some parts of the header file are changed depending on which is in use.
The exports are adjusted also since some functions are not available with
driver model.
Boards must define CONFIG_DM_SPI to use driver model for SPI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
(Discussed some follow-up comments which will address in future add-ons)
|
|
Some of the #defines in spi.h are not bracketed. To avoid future mistakes
add brackets. Also add an explanatory comment for SPI_CONN_DUAL_...
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
This patch added support for accessing dual memories in
parallel connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
This patch added support for accessing dual memories in
stacked connection with single chipselect line from controller.
For more info - see doc/SPI/README.dual-flash
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|