From f76750d1113380462413bad94d7a400af1aa4909 Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Sat, 11 Dec 2021 14:55:51 -0500 Subject: Convert CONFIG_CONS_INDEX et al to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini --- README | 29 ----------------------------- 1 file changed, 29 deletions(-) (limited to 'README') diff --git a/README b/README index 3496bef777..fa56061108 100644 --- a/README +++ b/README @@ -565,11 +565,6 @@ The following options need to be configured: boards with QUICC Engines require OF_QE to set UCC MAC addresses - CONFIG_OF_BOARD_SETUP - - Board code has addition modification that it wants to make - to the flat device tree before handing it off to the kernel - CONFIG_OF_SYSTEM_SETUP Other code has addition modification that it wants to make @@ -596,9 +591,6 @@ The following options need to be configured: Note: If a "bootargs" environment is defined, it will override the defaults discussed just above. -- Cache Configuration: - CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot - - Cache Configuration for ARM: CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache controller @@ -1520,16 +1512,6 @@ The following options need to be configured: SPI EEPROM, also an instance works with Crystal A/D and D/As on the SACSng board) - CONFIG_SOFT_SPI - - Enables a software (bit-bang) SPI driver rather than - using hardware support. This is a general purpose - driver that only requires three general I/O port pins - (two outputs, one input) to function. If this is - defined, the board configuration must define several - SPI configuration items (port pins to use, etc). For - an example, see include/configs/sacsng.h. - CONFIG_SYS_SPI_MXC_WAIT Timeout for waiting until spi transfer completed. default: (CONFIG_SYS_HZ/100) /* 10 ms */ @@ -1595,13 +1577,6 @@ The following options need to be configured: Time to wait after FPGA configuration. The default is 200 ms. -- Configuration Management: - - CONFIG_IDENT_STRING - - If defined, this string will be added to the U-Boot - version information (U_BOOT_VERSION) - - Vendor Parameter Protection: U-Boot considers the values of the environment @@ -1922,10 +1897,6 @@ The following options need to be configured: CONFIG_SPL_INIT_MINIMAL Arch init code should be built for a very small image - CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION - Partition on the MMC to load U-Boot from when the MMC is being - used in raw mode - CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR Sector to load kernel uImage from when MMC is being used in raw mode (for Falcon mode) -- cgit v1.2.3