/* * Copyright 2013-2015 Arcturus Networks, Inc. * http://www.arcturusnetworks.com/products/ucp1020/ * based on include/configs/p1_p2_rdb_pc.h * original copyright follows: * Copyright 2009-2011 Freescale Semiconductor, Inc. * * SPDX-License-Identifier: GPL-2.0+ */ /* * QorIQ uCP1020-xx boards configuration file */ #ifndef __CONFIG_H #define __CONFIG_H #define CONFIG_FSL_ELBC #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ #if defined(CONFIG_TARTGET_UCP1020T1) #define CONFIG_UCP1020_REV_1_3 #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" #define CONFIG_TSEC_ENET #define CONFIG_TSEC1 #define CONFIG_TSEC3 #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD #define CONFIG_IPADDR 10.80.41.229 #define CONFIG_SERVERIP 10.80.41.227 #define CONFIG_NETMASK 255.255.252.0 #define CONFIG_ETHPRIME "eTSEC3" #ifndef CONFIG_SPI_FLASH #endif #define CONFIG_SYS_REDUNDAND_ENVIRONMENT #define CONFIG_SYS_L2_SIZE (256 << 10) #define CONFIG_LAST_STAGE_INIT #endif #if defined(CONFIG_TARGET_UCP1020) #define CONFIG_UCP1020 #define CONFIG_UCP1020_REV_1_3 #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" #define CONFIG_TSEC_ENET #define CONFIG_TSEC1 #define CONFIG_TSEC2 #define CONFIG_TSEC3 #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD #define CONFIG_IPADDR 192.168.1.81 #define CONFIG_IPADDR1 192.168.1.82 #define CONFIG_IPADDR2 192.168.1.83 #define CONFIG_SERVERIP 192.168.1.80 #define CONFIG_GATEWAYIP 102.168.1.1 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_ETHPRIME "eTSEC1" #ifndef CONFIG_SPI_FLASH #endif #define CONFIG_SYS_REDUNDAND_ENVIRONMENT #define CONFIG_SYS_L2_SIZE (256 << 10) #define CONFIG_LAST_STAGE_INIT #endif #ifdef CONFIG_SDCARD #define CONFIG_RAMBOOT_SDCARD #define CONFIG_SYS_RAMBOOT #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_SYS_TEXT_BASE 0x11000000 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif #ifdef CONFIG_SPIFLASH #define CONFIG_RAMBOOT_SPIFLASH #define CONFIG_SYS_RAMBOOT #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_SYS_TEXT_BASE 0x11000000 #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xeff80000 #endif #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 #ifndef CONFIG_RESET_VECTOR_ADDRESS #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc #endif #ifndef CONFIG_SYS_MONITOR_BASE #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif #define CONFIG_MP #define CONFIG_ENV_OVERWRITE #define CONFIG_CMD_SATA #define CONFIG_SATA_SIL #define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_LIBATA #define CONFIG_LBA48 #define CONFIG_SYS_CLK_FREQ 66666666 #define CONFIG_DDR_CLK_FREQ 66666666 #define CONFIG_HWCONFIG #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ /* * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). * there will be one entry in this array for each two (dummy) sensors in * CONFIG_DTT_SENSORS. * * For uCP1020 module: * - only one ADM1021/NCT72 * - i2c addr 0x41 * - conversion rate 0x02 = 0.25 conversions/second * - ALERT output disabled * - local temp sensor enabled, min set to 0 deg, max set to 85 deg * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg */ #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ 0x02, 0, 1, 0, 85, 1, 0, 85} } #define CONFIG_CMD_DTT /* * These can be toggled for performance analysis, otherwise use default. */ #define CONFIG_L2_CACHE #define CONFIG_BTB #define CONFIG_ENABLE_36BIT_PHYS #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ #define CONFIG_SYS_MEMTEST_END 0x1fffffff #define CONFIG_PANIC_HANG /* do not reset board on panic */ #define CONFIG_SYS_CCSRBAR 0xffe00000 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k SPL code*/ #ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif /* DDR Setup */ #define CONFIG_DDR_ECC_ENABLE #ifndef CONFIG_DDR_ECC_ENABLE #define CONFIG_SYS_DDR_RAW_TIMING #define CONFIG_DDR_SPD #endif #define CONFIG_SYS_SPD_BUS_NUM 1 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M #define CONFIG_CHIP_SELECTS_PER_CTRL 1 #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_DIMM_SLOTS_PER_CTLR 1 /* Default settings for DDR3 */ #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 #define CONFIG_SYS_DDR_RCW_1 0x00000000 #define CONFIG_SYS_DDR_RCW_2 0x00000000 #ifdef CONFIG_DDR_ECC_ENABLE #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ #else #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ #endif #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 #define CONFIG_SYS_DDR_MODE_1 0x40461520 #define CONFIG_SYS_DDR_MODE_2 0x8000c000 #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 #undef CONFIG_CLOCKS_IN_MHZ /* * Memory map * * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable * (early boot only) * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable */ /* * Local Bus Definitions */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ #define CONFIG_SYS_FLASH_BASE 0xec000000 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ | BR_PS_16 | BR_V) #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} #define CONFIG_SYS_FLASH_QUIET_TEST #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ #undef CONFIG_SYS_FLASH_CHECKSUM #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ #define CONFIG_SYS_INIT_RAM_LOCK #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS /* Size of used area in RAM */ #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ #define CONFIG_SYS_PMC_BASE 0xff980000 #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ BR_PS_8 | BR_V) #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ OR_GPCM_EAD) #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ #ifdef CONFIG_NAND_FSL_ELBC #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #endif /* Serial Port - controlled on board with jumper J8 * open - index 2 * shorted - index 1 */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) #define CONFIG_NS16550_MIN_FUNCTIONS #endif #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) /* I2C */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 400000 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ #define CONFIG_RTC_DS1337 #define CONFIG_SYS_RTC_DS1337_NOOSC #define CONFIG_SYS_I2C_RTC_ADDR 0x68 #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C #define CONFIG_SYS_I2C_IDT6V49205B 0x69 /* * eSPI - Enhanced SPI */ #define CONFIG_HARD_SPI #define CONFIG_SF_DEFAULT_SPEED 10000000 #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #if defined(CONFIG_PCI) /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* controller 2, direct to uli, tgtid 2, Base address 9000 */ #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ /* controller 1, Slot 2, tgtid 1, Base address a000 */ #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ #define CONFIG_CMD_PCI #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #endif /* CONFIG_PCI */ /* * Environment */ #ifdef CONFIG_ENV_FIT_UCBOOT #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) #define CONFIG_ENV_SIZE 0x20000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #else #define CONFIG_ENV_SPI_BUS 0 #define CONFIG_ENV_SPI_CS 0 #define CONFIG_ENV_SPI_MAX_HZ 10000000 #define CONFIG_ENV_SPI_MODE 0 #ifdef CONFIG_RAMBOOT_SPIFLASH #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ #define CONFIG_ENV_SECT_SIZE 0x1000 #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #endif #elif defined(CONFIG_RAMBOOT_SDCARD) #define CONFIG_ENV_IS_IN_MMC #define CONFIG_FSL_FIXED_MMC_LOCATION #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_SYS_MMC_ENV_DEV 0 #elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #endif #endif #endif /* CONFIG_ENV_FIT_UCBOOT */ #define CONFIG_LOADS_ECHO /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ /* * Command line configuration. */ #define CONFIG_CMD_IRQ #define CONFIG_CMD_DATE #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO #define CONFIG_CMD_ERRATA #define CONFIG_CMD_CRAMFS /* * USB */ #define CONFIG_HAS_FSL_DR_USB #if defined(CONFIG_HAS_FSL_DR_USB) #define CONFIG_USB_EHCI #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 #ifdef CONFIG_USB_EHCI #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_EHCI_FSL #endif #endif #undef CONFIG_WATCHDOG /* watchdog disabled */ #ifdef CONFIG_MMC #define CONFIG_FSL_ESDHC #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR #define CONFIG_MMC_SPI #define CONFIG_CMD_MMC_SPI #define CONFIG_GENERIC_MMC #endif /* Misc Extra Settings */ #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_CMDLINE_EDITING /* Command-line editing */ #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */ #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ /* * For booting Linux, the board info and command line data * have to be in the first 64 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif /* * Environment Configuration */ #if defined(CONFIG_TSEC_ENET) #if defined(CONFIG_UCP1020_REV_1_2) #define CONFIG_PHY_MICREL_KSZ9021 #elif defined(CONFIG_UCP1020_REV_1_3) #define CONFIG_PHY_MICREL_KSZ9031 #else #error "UCP1020 module revision is not defined !!!" #endif #define CONFIG_BOOTP_SERVERIP #define CONFIG_MII /* MII PHY management */ #define CONFIG_TSEC1_NAME "eTSEC1" #define CONFIG_TSEC2_NAME "eTSEC2" #define CONFIG_TSEC3_NAME "eTSEC3" #define TSEC1_PHY_ADDR 4 #define TSEC2_PHY_ADDR 0 #define TSEC2_PHY_ADDR_SGMII 0x00 #define TSEC3_PHY_ADDR 6 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define TSEC3_PHYIDX 0 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #endif #define CONFIG_HOSTNAME UCP1020 #define CONFIG_ROOTPATH "/opt/nfsroot" #define CONFIG_BOOTFILE "uImage" #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ /* default location for tftp and bootm */ #define CONFIG_LOADADDR 1000000 #define CONFIG_BOOTARGS /* the boot command will set bootargs */ #define CONFIG_BAUDRATE 115200 #if defined(CONFIG_DONGLE) #define CONFIG_EXTRA_ENV_SETTINGS \ "bootcmd=run prog_spi_mbrbootcramfs\0" \ "bootfile=uImage\0" \ "consoledev=ttyS0\0" \ "cramfsfile=image.cramfs\0" \ "dtbaddr=0x00c00000\0" \ "dtbfile=image.dtb\0" \ "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ "fileaddr=0x01000000\0" \ "filesize=0x00080000\0" \ "flashmbr=sf probe 0; " \ "tftp $loadaddr $mbr; " \ "sf erase $mbr_offset +$filesize; " \ "sf write $loadaddr $mbr_offset $filesize\0" \ "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ "protect off $nor_recoveryaddr +$filesize; " \ "erase $nor_recoveryaddr +$filesize; " \ "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ "protect on $nor_recoveryaddr +$filesize\0 " \ "flashuboot=tftp $ubootaddr $ubootfile; " \ "protect off $nor_ubootaddr +$filesize; " \ "erase $nor_ubootaddr +$filesize; " \ "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ "protect on $nor_ubootaddr +$filesize\0 " \ "flashworking=tftp $workingaddr $cramfsfile; " \ "protect off $nor_workingaddr +$filesize; " \ "erase $nor_workingaddr +$filesize; " \ "cp.b $workingaddr $nor_workingaddr $filesize; " \ "protect on $nor_workingaddr +$filesize\0 " \ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ "kerneladdr=0x01100000\0" \ "kernelfile=uImage\0" \ "loadaddr=0x01000000\0" \ "mbr=uCP1020d.mbr\0" \ "mbr_offset=0x00000000\0" \ "mmbr=uCP1020Quiet.mbr\0" \ "mmcpart=0:2\0" \ "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ "mmc erase 1 1; " \ "mmc write $loadaddr 1 1\0" \ "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ "mmc erase 0x40 0x400; " \ "mmc write $loadaddr 0x40 0x400\0" \ "netdev=eth0\0" \ "nor_recoveryaddr=0xEC0A0000\0" \ "nor_ubootaddr=0xEFF80000\0" \ "nor_workingaddr=0xECFA0000\0" \ "norbootrecovery=setenv bootargs $recoverybootargs" \ " console=$consoledev,$baudrate $othbootargs; " \ "run norloadrecovery; " \ "bootm $kerneladdr - $dtbaddr\0" \ "norbootworking=setenv bootargs $workingbootargs" \ " console=$consoledev,$baudrate $othbootargs; " \ "run norloadworking; " \ "bootm $kerneladdr - $dtbaddr\0" \ "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ "setenv cramfsaddr $nor_recoveryaddr; " \ "cramfsload $dtbaddr $dtbfile; " \ "cramfsload $kerneladdr $kernelfile\0" \ "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ "setenv cramfsaddr $nor_workingaddr; " \ "cramfsload $dtbaddr $dtbfile; " \ "cramfsload $kerneladdr $kernelfile\0" \ "prog_spi_mbr=run spi__mbr\0" \ "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ "run spi__cramfs\0" \ "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ " console=$consoledev,$baudrate $othbootargs; " \ "tftp $rootfsaddr $rootfsfile; " \ "tftp $loadaddr $kernelfile; " \ "tftp $dtbaddr $dtbfile; " \ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ "ramdisk_size=120000\0" \ "ramdiskfile=rootfs.ext2.gz.uboot\0" \ "recoveryaddr=0x02F00000\0" \ "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ "mw.l 0xffe0f008 0x00400000\0" \ "rootfsaddr=0x02F00000\0" \ "rootfsfile=rootfs.ext2.gz.uboot\0" \ "rootpath=/opt/nfsroot\0" \ "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ "protect off 0xeC000000 +$filesize; " \ "erase 0xEC000000 +$filesize; " \ "cp.b $loadaddr 0xEC000000 $filesize; " \ "cmp.b $loadaddr 0xEC000000 $filesize; " \ "protect on 0xeC000000 +$filesize\0" \ "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ "protect off 0xeFF80000 +$filesize; " \ "erase 0xEFF80000 +$filesize; " \ "cp.b $loadaddr 0xEFF80000 $filesize; " \ "cmp.b $loadaddr 0xEFF80000 $filesize; " \ "protect on 0xeFF80000 +$filesize\0" \ "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ "sf probe 0; sf erase 0x8000 +$filesize; " \ "sf write $loadaddr 0x8000 $filesize\0" \ "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ "protect off 0xec0a0000 +$filesize; " \ "erase 0xeC0A0000 +$filesize; " \ "cp.b $loadaddr 0xeC0A0000 $filesize; " \ "protect on 0xec0a0000 +$filesize\0" \ "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ "sf probe 1; sf erase 0 +$filesize; " \ "sf write $loadaddr 0 $filesize\0" \ "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ "sf probe 0; sf erase 0 +$filesize; " \ "sf write $loadaddr 0 $filesize\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=0x01000000\0" \ "ubootfile=u-boot.bin\0" \ "ubootd=u-boot4dongle.bin\0" \ "upgrade=run flashworking\0" \ "usb_phy_type=ulpi\0 " \ "workingaddr=0x02F00000\0" \ "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" #else #if defined(CONFIG_UCP1020T1) #define CONFIG_EXTRA_ENV_SETTINGS \ "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ "bootfile=uImage\0" \ "consoledev=ttyS0\0" \ "cramfsfile=image.cramfs\0" \ "dtbaddr=0x00c00000\0" \ "dtbfile=image.dtb\0" \ "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ "fileaddr=0x01000000\0" \ "filesize=0x00080000\0" \ "flashmbr=sf probe 0; " \ "tftp $loadaddr $mbr; " \ "sf erase $mbr_offset +$filesize; " \ "sf write $loadaddr $mbr_offset $filesize\0" \ "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ "protect off $nor_recoveryaddr +$filesize; " \ "erase $nor_recoveryaddr +$filesize; " \ "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ "protect on $nor_recoveryaddr +$filesize\0 " \ "flashuboot=tftp $ubootaddr $ubootfile; " \ "protect off $nor_ubootaddr +$filesize; " \ "erase $nor_ubootaddr +$filesize; " \ "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ "protect on $nor_ubootaddr +$filesize\0 " \ "flashworking=tftp $workingaddr $cramfsfile; " \ "protect off $nor_workingaddr +$filesize; " \ "erase $nor_workingaddr +$filesize; " \ "cp.b $workingaddr $nor_workingaddr $filesize; " \ "protect on $nor_workingaddr +$filesize\0 " \ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ "kerneladdr=0x01100000\0" \ "kernelfile=uImage\0" \ "loadaddr=0x01000000\0" \ "mbr=uCP1020.mbr\0" \ "mbr_offset=0x00000000\0" \ "netdev=eth0\0" \ "nor_recoveryaddr=0xEC0A0000\0" \ "nor_ubootaddr=0xEFF80000\0" \ "nor_workingaddr=0xECFA0000\0" \ "norbootrecovery=setenv bootargs $recoverybootargs" \ " console=$consoledev,$baudrate $othbootargs; " \ "run norloadrecovery; " \ "bootm $kerneladdr - $dtbaddr\0" \ "norbootworking=setenv bootargs $workingbootargs" \ " console=$consoledev,$baudrate $othbootargs; " \ "run norloadworking; " \ "bootm $kerneladdr - $dtbaddr\0" \ "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ "setenv cramfsaddr $nor_recoveryaddr; " \ "cramfsload $dtbaddr $dtbfile; " \ "cramfsload $kerneladdr $kernelfile\0" \ "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ "setenv cramfsaddr $nor_workingaddr; " \ "cramfsload $dtbaddr $dtbfile; " \ "cramfsload $kerneladdr $kernelfile\0" \ "othbootargs=quiet\0" \ "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ " console=$consoledev,$baudrate $othbootargs; " \ "tftp $rootfsaddr $rootfsfile; " \ "tftp $loadaddr $kernelfile; " \ "tftp $dtbaddr $dtbfile; " \ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ "ramdisk_size=120000\0" \ "ramdiskfile=rootfs.ext2.gz.uboot\0" \ "recoveryaddr=0x02F00000\0" \ "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ "mw.l 0xffe0f008 0x00400000\0" \ "rootfsaddr=0x02F00000\0" \ "rootfsfile=rootfs.ext2.gz.uboot\0" \ "rootpath=/opt/nfsroot\0" \ "silent=1\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=0x01000000\0" \ "ubootfile=u-boot.bin\0" \ "upgrade=run flashworking\0" \ "workingaddr=0x02F00000\0" \ "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" #else /* For Arcturus Modules */ #define CONFIG_EXTRA_ENV_SETTINGS \ "bootcmd=run norkernel\0" \ "bootfile=uImage\0" \ "consoledev=ttyS0\0" \ "dtbaddr=0x00c00000\0" \ "dtbfile=image.dtb\0" \ "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ "fileaddr=0x01000000\0" \ "filesize=0x00080000\0" \ "flashmbr=sf probe 0; " \ "tftp $loadaddr $mbr; " \ "sf erase $mbr_offset +$filesize; " \ "sf write $loadaddr $mbr_offset $filesize\0" \ "flashuboot=tftp $loadaddr $ubootfile; " \ "protect off $nor_ubootaddr0 +$filesize; " \ "erase $nor_ubootaddr0 +$filesize; " \ "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ "protect on $nor_ubootaddr0 +$filesize; " \ "protect off $nor_ubootaddr1 +$filesize; " \ "erase $nor_ubootaddr1 +$filesize; " \ "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ "protect on $nor_ubootaddr1 +$filesize\0 " \ "format0=protect off $part0base +$part0size; " \ "erase $part0base +$part0size\0" \ "format1=protect off $part1base +$part1size; " \ "erase $part1base +$part1size\0" \ "format2=protect off $part2base +$part2size; " \ "erase $part2base +$part2size\0" \ "format3=protect off $part3base +$part3size; " \ "erase $part3base +$part3size\0" \ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ "kerneladdr=0x01100000\0" \ "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ "kernelfile=uImage\0" \ "loadaddr=0x01000000\0" \ "mbr=uCP1020.mbr\0" \ "mbr_offset=0x00000000\0" \ "netdev=eth0\0" \ "nor_ubootaddr0=0xEC000000\0" \ "nor_ubootaddr1=0xEFF80000\0" \ "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ "run norkernelload; " \ "bootm $kerneladdr - $dtbaddr\0" \ "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ "setenv cramfsaddr $part0base; " \ "cramfsload $dtbaddr $dtbfile; " \ "cramfsload $kerneladdr $kernelfile\0" \ "part0base=0xEC100000\0" \ "part0size=0x00700000\0" \ "part1base=0xEC800000\0" \ "part1size=0x02000000\0" \ "part2base=0xEE800000\0" \ "part2size=0x00800000\0" \ "part3base=0xEF000000\0" \ "part3size=0x00F80000\0" \ "partENVbase=0xEC080000\0" \ "partENVsize=0x00080000\0" \ "program0=tftp part0-000000.bin; " \ "protect off $part0base +$filesize; " \ "erase $part0base +$filesize; " \ "cp.b $loadaddr $part0base $filesize; " \ "echo Verifying...; " \ "cmp.b $loadaddr $part0base $filesize\0" \ "program1=tftp part1-000000.bin; " \ "protect off $part1base +$filesize; " \ "erase $part1base +$filesize; " \ "cp.b $loadaddr $part1base $filesize; " \ "echo Verifying...; " \ "cmp.b $loadaddr $part1base $filesize\0" \ "program2=tftp part2-000000.bin; " \ "protect off $part2base +$filesize; " \ "erase $part2base +$filesize; " \ "cp.b $loadaddr $part2base $filesize; " \ "echo Verifying...; " \ "cmp.b $loadaddr $part2base $filesize\0" \ "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ " console=$consoledev,$baudrate $othbootargs; " \ "tftp $rootfsaddr $rootfsfile; " \ "tftp $loadaddr $kernelfile; " \ "tftp $dtbaddr $dtbfile; " \ "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ "ramdisk_size=120000\0" \ "ramdiskfile=rootfs.ext2.gz.uboot\0" \ "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ "mw.l 0xffe0f008 0x00400000\0" \ "rootfsaddr=0x02F00000\0" \ "rootfsfile=rootfs.ext2.gz.uboot\0" \ "rootpath=/opt/nfsroot\0" \ "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ "sf probe 0; sf erase 0 +$filesize; " \ "sf write $loadaddr 0 $filesize\0" \ "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ "protect off 0xeC000000 +$filesize; " \ "erase 0xEC000000 +$filesize; " \ "cp.b $loadaddr 0xEC000000 $filesize; " \ "cmp.b $loadaddr 0xEC000000 $filesize; " \ "protect on 0xeC000000 +$filesize\0" \ "tftpflash=tftpboot $loadaddr $uboot; " \ "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootfile=u-boot.bin\0" \ "upgrade=run flashuboot\0" \ "usb_phy_type=ulpi\0 " \ "boot_nfs= " \ "setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath " \ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ "console=$consoledev,$baudrate $othbootargs;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr - $fdtaddr\0" \ "boot_hd = " \ "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ "console=$consoledev,$baudrate $othbootargs;" \ "usb start;" \ "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ "bootm $loadaddr - $fdtaddr\0" \ "boot_usb_fat = " \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs " \ "ramdisk_size=$ramdisk_size;" \ "usb start;" \ "fatload usb 0:2 $loadaddr $bootfile;" \ "fatload usb 0:2 $fdtaddr $fdtfile;" \ "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ "boot_usb_ext2 = " \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs " \ "ramdisk_size=$ramdisk_size;" \ "usb start;" \ "ext2load usb 0:4 $loadaddr $bootfile;" \ "ext2load usb 0:4 $fdtaddr $fdtfile;" \ "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ "boot_nor = " \ "setenv bootargs root=/dev/$jffs2nor rw " \ "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ "bootm $norbootaddr - $norfdtaddr\0 " \ "boot_ram = " \ "setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs " \ "ramdisk_size=$ramdisk_size;" \ "tftp $ramdiskaddr $ramdiskfile;" \ "tftp $loadaddr $bootfile;" \ "tftp $fdtaddr $fdtfile;" \ "bootm $loadaddr $ramdiskaddr $fdtaddr\0" #endif #endif #endif /* __CONFIG_H */