1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
.. SPDX-License-Identifier: GPL-2.0+
Kontron Electronics i.MX8MM SoMs and Boards
===========================================
The SL i.MX8MM and OSM-S i.MX8MM by Kontron Electronics GmbH are SoM modules
with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC.
The matching evaluation boards (Board-Line, BL) have two Ethernet ports,
USB 2.0, HDMI/LVDS, SD card, CAN, RS485, RS232 and much more.
The OSM-S i.MX8MM is compliant to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
Quick Start
-----------
- Get and Build the Trusted Firmware-A (TF-A)
- Get the DDR firmware
- Build U-Boot
- Boot
Get and Build the Trusted Firmware-A (TF-A)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Note: builddir is U-Boot build directory (source directory for in-tree builds)
There are two sources for the TF-A. Mainline and NXP. Get the one you prefer
(support and features might differ).
**NXP's imx-atf**
1. Get TF-A from: https://source.codeaurora.org/external/imx/imx-atf, branch: imx_5.4.70_2.3.0
2. Apply the patch to select the correct UART for the console, otherwise the TF-A will lock up during boot.
3. Build
.. code-block:: bash
$ make PLAT=imx8mm bl31
$ cp build/imx8mm/release/bl31.bin $(builddir)
**Mainline TF-A**
1. Get TF-A from: https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/, tag: v2.4
2. Build
.. code-block:: bash
$ make PLAT=imx8mm CROSS_COMPILE=aarch64-linux-gnu- IMX_BOOT_UART_BASE="0x30880000" bl31
$ cp build/imx8mm/release/bl31.bin $(builddir)
Get the DDR firmware
^^^^^^^^^^^^^^^^^^^^
.. code-block:: bash
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
$ chmod +x firmware-imx-8.9.bin
$ ./firmware-imx-8.9.bin
$ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
Build U-Boot
^^^^^^^^^^^^
.. code-block:: bash
$ make kontron-sl-mx8mm_defconfig
$ make
Burn the flash.bin to SD card at an offset of 33 KiB:
.. code-block:: bash
$ dd if=flash.bin of=/dev/sd[x] bs=1K seek=33 conv=notrunc
Boot
^^^^
Put the SD card in the slot on the board and apply power.
Further Information
-------------------
The bootloader configuration is setup to be used with kernel FIT images. Legacy
images might not be working out of the box.
Please see https://docs.kontron-electronics.de for further vendor documentation.
|
