summaryrefslogtreecommitdiff
path: root/drivers/serial/serial_zynq.c
blob: 0e71cada1bbadf4b24a385371d8d7fb22a352c67 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2012 Michal Simek <monstr@monstr.eu>
 * Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
 */

#include <clk.h>
#include <common.h>
#include <debug_uart.h>
#include <dm.h>
#include <errno.h>
#include <fdtdec.h>
#include <log.h>
#include <watchdog.h>
#include <asm/io.h>
#include <dm/device_compat.h>
#include <linux/bitops.h>
#include <linux/compiler.h>
#include <serial.h>
#include <linux/err.h>

#define ZYNQ_UART_SR_TXACTIVE	BIT(11) /* TX active */
#define ZYNQ_UART_SR_TXFULL	BIT(4) /* TX FIFO full */
#define ZYNQ_UART_SR_RXEMPTY	BIT(1) /* RX FIFO empty */

#define ZYNQ_UART_CR_TX_EN	BIT(4) /* TX enabled */
#define ZYNQ_UART_CR_RX_EN	BIT(2) /* RX enabled */
#define ZYNQ_UART_CR_TXRST	BIT(1) /* TX logic reset */
#define ZYNQ_UART_CR_RXRST	BIT(0) /* RX logic reset */

#define ZYNQ_UART_MR_PARITY_NONE	0x00000020  /* No parity mode */

struct uart_zynq {
	u32 control; /* 0x0 - Control Register [8:0] */
	u32 mode; /* 0x4 - Mode Register [10:0] */
	u32 reserved1[4];
	u32 baud_rate_gen; /* 0x18 - Baud Rate Generator [15:0] */
	u32 reserved2[4];
	u32 channel_sts; /* 0x2c - Channel Status [11:0] */
	u32 tx_rx_fifo; /* 0x30 - FIFO [15:0] or [7:0] */
	u32 baud_rate_divider; /* 0x34 - Baud Rate Divider [7:0] */
};

struct zynq_uart_platdata {
	struct uart_zynq *regs;
};

/* Set up the baud rate */
static void _uart_zynq_serial_setbrg(struct uart_zynq *regs,
				     unsigned long clock, unsigned long baud)
{
	/* Calculation results. */
	unsigned int calc_bauderror, bdiv, bgen;
	unsigned long calc_baud = 0;

	/* Covering case where input clock is so slow */
	if (clock < 1000000 && baud > 4800)
		baud = 4800;

	/*                master clock
	 * Baud rate = ------------------
	 *              bgen * (bdiv + 1)
	 *
	 * Find acceptable values for baud generation.
	 */
	for (bdiv = 4; bdiv < 255; bdiv++) {
		bgen = clock / (baud * (bdiv + 1));
		if (bgen < 2 || bgen > 65535)
			continue;

		calc_baud = clock / (bgen * (bdiv + 1));

		/*
		 * Use first calculated baudrate with
		 * an acceptable (<3%) error
		 */
		if (baud > calc_baud)
			calc_bauderror = baud - calc_baud;
		else
			calc_bauderror = calc_baud - baud;
		if (((calc_bauderror * 100) / baud) < 3)
			break;
	}

	writel(bdiv, &regs->baud_rate_divider);
	writel(bgen, &regs->baud_rate_gen);
}

/* Initialize the UART, with...some settings. */
static void _uart_zynq_serial_init(struct uart_zynq *regs)
{
	/* RX/TX enabled & reset */
	writel(ZYNQ_UART_CR_TX_EN | ZYNQ_UART_CR_RX_EN | ZYNQ_UART_CR_TXRST | \
					ZYNQ_UART_CR_RXRST, &regs->control);
	writel(ZYNQ_UART_MR_PARITY_NONE, &regs->mode); /* 8 bit, no parity */
}

static int _uart_zynq_serial_putc(struct uart_zynq *regs, const char c)
{
	if (readl(&regs->channel_sts) & ZYNQ_UART_SR_TXFULL)
		return -EAGAIN;

	writel(c, &regs->tx_rx_fifo);

	return 0;
}

static int zynq_serial_setbrg(struct udevice *dev, int baudrate)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);
	unsigned long clock;

	int ret;
	struct clk clk;

	ret = clk_get_by_index(dev, 0, &clk);
	if (ret < 0) {
		dev_err(dev, "failed to get clock\n");
		return ret;
	}

	clock = clk_get_rate(&clk);
	if (IS_ERR_VALUE(clock)) {
		dev_err(dev, "failed to get rate\n");
		return clock;
	}
	debug("%s: CLK %ld\n", __func__, clock);

	ret = clk_enable(&clk);
	if (ret && ret != -ENOSYS) {
		dev_err(dev, "failed to enable clock\n");
		return ret;
	}

	_uart_zynq_serial_setbrg(platdata->regs, clock, baudrate);

	return 0;
}

static int zynq_serial_probe(struct udevice *dev)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);
	struct uart_zynq *regs = platdata->regs;
	u32 val;

	/* No need to reinitialize the UART if TX already enabled */
	val = readl(&regs->control);
	if (val & ZYNQ_UART_CR_TX_EN)
		return 0;

	_uart_zynq_serial_init(platdata->regs);

	return 0;
}

static int zynq_serial_getc(struct udevice *dev)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);
	struct uart_zynq *regs = platdata->regs;

	if (readl(&regs->channel_sts) & ZYNQ_UART_SR_RXEMPTY)
		return -EAGAIN;

	return readl(&regs->tx_rx_fifo);
}

static int zynq_serial_putc(struct udevice *dev, const char ch)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);

	return _uart_zynq_serial_putc(platdata->regs, ch);
}

static int zynq_serial_pending(struct udevice *dev, bool input)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);
	struct uart_zynq *regs = platdata->regs;

	if (input)
		return !(readl(&regs->channel_sts) & ZYNQ_UART_SR_RXEMPTY);
	else
		return !!(readl(&regs->channel_sts) & ZYNQ_UART_SR_TXACTIVE);
}

static int zynq_serial_ofdata_to_platdata(struct udevice *dev)
{
	struct zynq_uart_platdata *platdata = dev_get_platdata(dev);

	platdata->regs = (struct uart_zynq *)dev_read_addr(dev);
	if (IS_ERR(platdata->regs))
		return PTR_ERR(platdata->regs);

	return 0;
}

static const struct dm_serial_ops zynq_serial_ops = {
	.putc = zynq_serial_putc,
	.pending = zynq_serial_pending,
	.getc = zynq_serial_getc,
	.setbrg = zynq_serial_setbrg,
};

static const struct udevice_id zynq_serial_ids[] = {
	{ .compatible = "xlnx,xuartps" },
	{ .compatible = "cdns,uart-r1p8" },
	{ .compatible = "cdns,uart-r1p12" },
	{ }
};

U_BOOT_DRIVER(serial_zynq) = {
	.name	= "serial_zynq",
	.id	= UCLASS_SERIAL,
	.of_match = zynq_serial_ids,
	.ofdata_to_platdata = zynq_serial_ofdata_to_platdata,
	.platdata_auto_alloc_size = sizeof(struct zynq_uart_platdata),
	.probe = zynq_serial_probe,
	.ops	= &zynq_serial_ops,
};

#ifdef CONFIG_DEBUG_UART_ZYNQ
static inline void _debug_uart_init(void)
{
	struct uart_zynq *regs = (struct uart_zynq *)CONFIG_DEBUG_UART_BASE;

	_uart_zynq_serial_init(regs);
	_uart_zynq_serial_setbrg(regs, CONFIG_DEBUG_UART_CLOCK,
				 CONFIG_BAUDRATE);
}

static inline void _debug_uart_putc(int ch)
{
	struct uart_zynq *regs = (struct uart_zynq *)CONFIG_DEBUG_UART_BASE;

	while (_uart_zynq_serial_putc(regs, ch) == -EAGAIN)
		WATCHDOG_RESET();
}

DEBUG_UART_FUNCS

#endif