blob: 363378b574c782f0bc144e1c821e614aa1a5af3f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2022 Marek Vasut <marex@denx.de>
*/
#ifndef __IMX8MM_DATA_MODUL_EDM_SBC_H
#define __IMX8MM_DATA_MODUL_EDM_SBC_H
#include <linux/sizes.h>
#include <linux/stringify.h>
#include <asm/arch/imx-regs.h>
#ifdef CONFIG_SPL_BUILD
#define CONFIG_MALLOC_F_ADDR 0x930000
/* For RAW image gives a error info not panic */
#endif
/* Link Definitions */
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x200000
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0x40000000 /* Minimum 1 GiB DDR */
#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR
/* PHY needs a longer autonegotiation timeout after reset */
#define PHY_ANEG_TIMEOUT 20000
/* USDHC */
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_EXTRA_ENV_SETTINGS \
"altbootcmd=setenv devpart 2 && run bootcmd ; reset\0" \
"bootlimit=3\0" \
"devtype=mmc\0" \
"devpart=1\0" \
/* Give slow devices beyond USB HUB chance to come up. */ \
"usb_pgood_delay=2000\0" \
"dfu_alt_info=" \
/* RAM block at DRAM offset 256..768 MiB */ \
"ram ram0=ram ram 0x50000000 0x20000000&" \
/* 16 MiB SPI NOR */ \
"mtd nor0=sf raw 0x0 0x1000000\0" \
"dmo_preboot=" \
"sf probe ; " /* Scan for SPI NOR, needed by DFU */ \
/* Attempt to start USB and Network console */ \
"run dmo_usb_cdc_acm_start ; " \
"run dmo_netconsole_start\0" \
"dmo_update_env=" \
"setenv dmo_update_env true ; saveenv ; saveenv\0" \
"dmo_usb_cdc_acm_start=" \
"if test \"${dmo_usb_cdc_acm_enabled}\" = \"true\" ; then "\
/* Ungate IMX8MM_CLK_USB1_CTRL_ROOT */ \
"mw 0x303844d0 3 ; " \
/* Read USBNC_n_PHY_STATUS BIT(4) VBUS_VLD */ \
"setexpr.l usbnc_n_phy_status *0x32e4023c \\\\& 0x8 ; " \
/* If USB OTG has valid VBUS, enable CDC ACM */ \
"if test \"${usbnc_n_phy_status}\" -eq 8 ; then "\
"usb start && " \
"setenv stderr ${stderr},usbacm && " \
"setenv stdout ${stdout},usbacm && " \
"setenv stdin ${stdin},usbacm ; " \
"fi ; " \
"fi\0" \
"dmo_netconsole_start=" \
"if test \"${dmo_netconsole_enabled}\" = \"true\" ; then "\
"setenv autoload false && " \
"dhcp && " \
"setenv autoload && " \
"setenv ncip ${serverip} && " \
"setenv stderr ${stderr},nc && " \
"setenv stdout ${stdout},nc && " \
"setenv stdin ${stdin},nc ; " \
"fi"
#endif
|