blob: 227f26492316961c1acd1609edf7a5cee998f4b2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
|
#!/bin/bash
# shellcheck disable=SC2046
do_fru_upgrade() {
FRU_DEVICE="/sys/bus/i2c/devices/3-0050/eeprom"
if ! command -v ampere_fru_upgrade;
then
echo "Bypass fru update as no ampere_fru_upgrade available"
exit
fi
ampere_fru_upgrade -d $FRU_DEVICE -f "$IMAGE"
systemctl restart xyz.openbmc_project.FruDevice.service
}
do_smpmpro_upgrade() {
I2C_BUS_DEV="1"
EEPROM_ADDR="0x50"
if ! command -v ampere_eeprom_prog;
then
echo "Bypass SCP firmware update as no ampere_eeprom_prog available"
exit
fi
echo "SECPRO mode: $SECPRO"
# Turn off the Host if it is currently ON
chassisstate=$(obmcutil chassisstate | awk -F. '{print $NF}')
echo "Current Chassis State: $chassisstate"
if [ "$chassisstate" == 'On' ];
then
echo "Turning the Chassis off"
obmcutil chassisoff
# Wait 60s until Chassis is off
cnt=30
while [ "$cnt" -gt 0 ];
do
cnt=$((cnt - 1))
sleep 2
# Check if HOST was OFF
chassisstate_off=$(obmcutil chassisstate | awk -F. '{print $NF}')
if [ "$chassisstate_off" != 'On' ];
then
break
fi
if [ "$cnt" == "0" ];
then
echo "--- Error : Failed turning the Chassis off"
exit 1
fi
done
fi
if [[ $SECPRO == 1 ]]; then
gpioset $(gpiofind host0-special-boot)=1
gpioset $(gpiofind s1-special-boot)=1
fi
# Switch EEPROM control to BMC AST2500 I2C
gpioset $(gpiofind spi0-program-sel)=0
# 08 is BMC_GPIOB0_I2C_BACKUP_SEL
if [[ $DEV_SEL == 1 ]]; then
echo "Run update primary Boot EEPROM"
gpioset $(gpiofind i2c-backup-sel)=1 # Main EEPROM
elif [[ $DEV_SEL == 2 ]]; then
echo "Run update secondary Boot EEPROM"
gpioset $(gpiofind i2c-backup-sel)=0 # Second EEPROM
else
echo "Please choose Main (1) or Second EEPROM (2)"
exit 0
fi
# Write Firmware to EEPROM and read back for validation
ampere_eeprom_prog -b $I2C_BUS_DEV -s $EEPROM_ADDR -p -f "$IMAGE"
# Switch EEPROM control to Host
# 08 is BMC_GPIOB0_I2C_BACKUP_SEL
gpioset $(gpiofind i2c-backup-sel)=1
gpioset $(gpiofind spi0-program-sel)=1
# Deassert SECPRO GPIO PINs
if [[ $SECPRO == 1 ]]; then
echo "De-asserting special GPIO PINs"
gpioset $(gpiofind host0-special-boot)=0
gpioset $(gpiofind s1-special-boot)=0
fi
if [ "$chassisstate" == 'On' ];
then
sleep 5
echo "Turn on the Host"
obmcutil poweron
fi
}
if [ $# -eq 0 ]; then
echo "Usage:"
echo " $(basename "$0") <Type> <Image file> <DEV_SEL> [SECPRO]"
echo "Where:"
echo " <Type>: smpmpro or fru"
echo " If Type is smpmpro, then DEV_SEL must is 1 (MAIN EEPROM), 2 (Failover)"
echo " SECPRO: Optional, input '1' to enter & flash secpro mode. Default: 0"
exit 0
fi
TYPE=$1
IMAGE=$2
if [ -z "$3" ]
then
DEV_SEL="1" # by default, select Main image
else
DEV_SEL=$3
fi
SECPRO=0
if [ -n "$4" ]; then
if [[ "$4" == "1" ]]; then
SECPRO=1
fi
fi
MANIFEST="$(echo "$IMAGE" | cut -d'/' -f-4)/MANIFEST"
if [ -f "$MANIFEST" ]; then
echo "MANIFEST: $MANIFEST"
if grep -qF "SECPRO" "$MANIFEST"; then
SECPRO=1
fi
fi
# Restrict to flash failover in case of SECPRO
if [ $SECPRO == 1 ] && [ "$DEV_SEL" == 2 ]; then
echo "Not allow to flash the failover with SECPRO image"
exit
fi
if [[ $TYPE == "smpmpro" ]]; then
do_smpmpro_upgrade
elif [[ $TYPE == "fru" ]]; then
do_fru_upgrade
fi
|
