ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 134 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
new file mode 100644
index 000000000000..31c0a69771c4
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree include file for Intel reference designs for the
+ * XScale Network Processors in the IXP 4xx series. Common device
+ * set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465.
+ */
+
+/ {
+	memory@0 {
+		/*
+		 * The board supports up to 256 MB of memory. Here we put in
+		 * 64 MB and this may be modified by the boot loader.
+		 */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@50 {
+			/*
+			 * Philips PCF8582C-2T/03 512byte I2C EEPROM
+			 * should behave like an Atmel 24c04.
+			 */
+			compatible = "atmel,24c04";
+			reg = <0x50>;
+			pagesize = <16>;
+			size = <512>;
+			read-only;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			/* Flash memory defined per-variant */
+			nand-controller@3,0 {
+				/* Some designs have a NAND on CS3 enable it here if present */
+				status = "disabled";
+
+				/*
+				 * gen_nand needs to be extended and documented to get
+				 * command byte = 1 and address byte = 2 from the device
+				 * tree.
+				 */
+				compatible = "gen_nand";
+
+				/* Expansion bus set-up */
+				intel,ixp4xx-eb-t1 = <0>;
+				intel,ixp4xx-eb-t2 = <0>;
+				intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase
+				intel,ixp4xx-eb-t4 = <0>;
+				intel,ixp4xx-eb-t5 = <0>;
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
+				intel,ixp4xx-eb-byte-access-on-halfword = <0>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+
+				/* 512 bytes memory window */
+				reg = <3 0x00000000 0x200>;
+				nand-on-flash-bbt;
+				nand-ecc-mode = "soft_bch";
+				nand-ecc-step-size = <512>;
+				nand-ecc-strength = <4>;
+				nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */
+
+				label = "ixp400 NAND";
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					fs@0 {
+						label = "ixp400 NAND FS 0";
+						reg = <0x0 0x800000>;
+					};
+					fs@800000 {
+						label = "ixp400 NAND FS 1";
+						reg = <0x800000 0x0>;
+					};
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from IXDP425 PCI boardfile.
+			 * PCI slots on the BIXMB425BD base card.
+			 * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
+			<0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
+			<0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
+			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
+			<0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
+			/* IDSEL 4 */
+			<0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
+			<0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
+			<0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
+			<0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
+		};
+	};
+};