ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
  been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
  company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com> #Xilinx
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Acked-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com> #hisilicon
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #broadcom
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Romain Perier <romain.perier@gmail.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 887 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
new file mode 100644
index 000000000000..b21e40da3dfd
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
@@ -0,0 +1,887 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Beam GT-I8530 also known as Gavini.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Beam (GT-I8530)";
+	compatible = "samsung,gavini", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb585157lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO193 EN */
+		gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-projector {
+			linux,code = <KEY_SWITCHVIDEOMODE>;
+			label = "Projector";
+			/* GPIO32 "Projector On HotKey" */
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_leds_default_mode>;
+		used-led {
+			label = "touchkeys";
+			/* GPIO68 */
+			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ktd259: backlight {
+		compatible = "kinetic,ktd259";
+		/* GPIO20 */
+		enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd259_backlight_default_mode>;
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas530_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * TODO: See if we can use the PL023 for this instead.
+	 */
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,lms397kf04";
+			/* 300 ns at read cycle -> 3 MHz max speed */
+			//spi-max-frequency = <3000000>;
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd259>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "MPR_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the DPP2601 projector I2C device 0x1b here */
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			/* "flash detect" actually card detect */
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>;
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <43000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			/* FIXME: fix the proximity sensor bindings and driver */
+			proximity@39 {
+				/* Gavini has the GP2A030S00F proximity sensor */
+				compatible = "sharp,gp2a030s00f";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+				/* FIXME: GPIO146 provides power on, IR LED? */
+			};
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				mount-matrix = "0", "1", "0",
+					       "1", "0", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222E accelerometer */
+					accelerometer@18 {
+						compatible = "bosch,bma222e";
+						reg = <0x18>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C2 "AGC I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_1_default>;
+			pinctrl-1 = <&i2c2_b_1_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_default>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Melfas MMS136 touchscreen */
+			touchscreen@48 {
+				compatible = "melfas,mms136";
+				reg = <0x48>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* AVDD is "analog supply", 2.57-3.47 V */
+				avdd-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			gavini_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			gavini_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			gavini_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS530 magnetometer */
+	yas530 {
+		yas530_default: yas530_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	gpio-leds {
+		gpio_leds_default_mode: gpio_leds_default {
+			/* EN_LED_LDO on GPIO68 */
+			gavini_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	backlight {
+		ktd259_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO20_AB4"; /* LCD_BL_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			gavini_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			gavini_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			gavini_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			gavini_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			gavini_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO193 */
+			skomer_cfg1 {
+				pins = "GPIO193_AH27";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO32_V2", /* Projector On HotKey */
+				       "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			gavini_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_default: mpu3050 {
+			gavini_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			gavini_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			gavini_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the TI DPP2601 */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			gavini_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9",
+				     "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			gavini_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			gavini_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_default: tsu6111 {
+			gavini_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+};