Merge tag 'sunxi-dt-for-6.7-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt

- Added V3s nodes for PWM pinctrl, EHCI and OHCI
- RISC-V DT cleanups
- Added new ISA property and PMU node to Allwinner D1
- Added interconnect to R40 video codec node
- New boards: Anbernic RG-Nano, BigTreeTech Pi, BigTreeTech CB1 SOM

* tag 'sunxi-dt-for-6.7-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  riscv: dts: allwinner: convert isa detection to new properties
  ARM: dts: sun8i-r40: Add interconnect to video-codec
  ARM: dts: sunxi: add support for Anbernic RG-Nano
  dt-bindings: arm: sunxi: add Anbernic RG-Nano
  ARM: dts: sun8i: v3s: add EHCI and OHCI to v3s dts
  arm: dts: sun8i: V3s: Add pinctrl for pwm
  riscv: dts: allwinner: d1: Add PMU event node
  arm64: dts: allwinner: h616: Add BigTreeTech Pi support
  arm64: dts: allwinner: h616: Add BigTreeTech CB1 SoM & boards support
  dt-bindings: arm: sunxi: Add BigTreeTech boards
  dt-bindings: vendor-prefixes: Add BigTreeTech
  arm64: dts: allwinner: h616: Add SID controller node
  dt-bindings: nvmem: SID: Add binding for H616 SID controller
  riscv: dts: allwinner: remove address-cells from intc node
  riscv: dts: use capital "OR" for multiple licenses in SPDX

Link: https://lore.kernel.org/r/20231013194203.GA2155816@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

4 files changed, 314 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
index eebb5a0c873a..2d26c3397f14 100644
--- a/arch/arm/boot/dts/allwinner/Makefile
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-t113s-mangopi-mq-r-t113.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3-sl631-imx179.dtb \
+	sun8i-v3s-anbernic-rg-nano.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
 	sun8i-v3s-licheepi-zero-dock.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
diff --git a/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
index 4ef26d8f5340..a5b1f1e3900d 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
@@ -338,6 +338,8 @@
 			resets = <&ccu RST_BUS_VE>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 			allwinner,sram = <&ve_sram 1>;
+			interconnects = <&mbus 4>;
+			interconnect-names = "dma-mem";
 		};
 
 		mmc0: mmc@1c0f000 {
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
new file mode 100644
index 000000000000..f34dfdf1566d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "sun8i-v3s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+	model = "Anbernic RG Nano";
+	compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s";
+
+	aliases {
+		rtc0 = &pcf8563;
+		rtc1 = &rtc;
+		serial0 = &uart0;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>;
+		default-brightness-level = <11>;
+		power-supply = <&reg_vcc5v0>;
+		pwms = <&pwm 0 40000 1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		button-a {
+			gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-A";
+			linux,code = <BTN_EAST>;
+		};
+
+		button-b {
+			gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-B";
+			linux,code = <BTN_SOUTH>;
+		};
+
+		button-down {
+			gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-DOWN";
+			linux,code = <BTN_DPAD_DOWN>;
+		};
+
+		button-left {
+			gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-LEFT";
+			linux,code = <BTN_DPAD_LEFT>;
+		};
+
+		button-right {
+			gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-RIGHT";
+			linux,code = <BTN_DPAD_RIGHT>;
+		};
+
+		button-se {
+			gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-SELECT";
+			linux,code = <BTN_SELECT>;
+		};
+
+		button-st {
+			gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-START";
+			linux,code = <BTN_START>;
+		};
+
+		button-tl {
+			gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-L";
+			linux,code = <BTN_TL>;
+		};
+
+		button-tr {
+			gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-R";
+			linux,code = <BTN_TR>;
+		};
+
+		button-up {
+			gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-UP";
+			linux,code = <BTN_DPAD_UP>;
+		};
+
+		button-x {
+			gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-X";
+			linux,code = <BTN_NORTH>;
+		};
+
+		button-y {
+			gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-Y";
+			linux,code = <BTN_WEST>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing = "Speaker", "HP",
+				  "MIC1", "Mic",
+				  "Mic", "HBIAS";
+	allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	gpio_expander: gpio@20 {
+		compatible = "nxp,pcal6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */
+		vcc-supply = <&reg_vcc3v3>;
+	};
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	spi0_no_miso_pins: spi0-no-miso-pins {
+		pins = "PC1", "PC2", "PC3";
+		function = "spi0";
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm0_pin>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-max-microvolt = <1250000>;
+	regulator-min-microvolt = <1250000>;
+	regulator-name = "vdd-cpu";
+};
+
+/* DCDC3 wired into every 3.3v input that isn't the RTC. */
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-max-microvolt = <3300000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-name = "vcc-io";
+};
+
+/* LDO1 wired into RTC, voltage is hard-wired at 3.3v. */
+&reg_ldo1 {
+	regulator-always-on;
+	regulator-name = "vcc-rtc";
+};
+
+/* LDO2 wired into VCC-PLL and audio codec. */
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3000000>;
+	regulator-name = "vcc-pll";
+};
+
+/* LDO3, LDO4, and LDO5 unused. */
+&reg_ldo3 {
+	status = "disabled";
+};
+
+&reg_ldo4 {
+	status = "disabled";
+};
+
+/* RTC uses internal oscillator */
+&rtc {
+	/delete-property/ clocks;
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_no_miso_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display@0 {
+		compatible = "saef,sftc154b", "panel-mipi-dbi-spi";
+		reg = <0>;
+		backlight = <&backlight>;
+		dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */
+		reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+		spi-max-frequency = <100000000>;
+
+		height-mm = <39>;
+		width-mm = <39>;
+
+		/* Set hb-porch to compensate for non-visible area */
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <80>;
+			vback-porch = <0>;
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
index 3b9a282c2746..e8a04476b776 100644
--- a/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
@@ -319,6 +319,29 @@
 			#phy-cells = <1>;
 		};
 
+		ehci: usb@1c1a000 {
+			compatible = "allwinner,sun8i-v3s-ehci", "generic-ehci";
+			reg = <0x01c1a000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci: usb@1c1a400 {
+			compatible = "allwinner,sun8i-v3s-ohci", "generic-ohci";
+			reg = <0x01c1a400 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-v3s-ccu";
 			reg = <0x01c20000 0x400>;
@@ -414,6 +437,18 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			pwm0_pin: pwm0-pin {
+				pins = "PB4";
+				function = "pwm0";
+			};
+
+			/omit-if-no-ref/
+			pwm1_pin: pwm1-pin {
+				pins = "PB5";
+				function = "pwm1";
+			};
+
 			spi0_pins: spi0-pins {
 				pins = "PC0", "PC1", "PC2", "PC3";
 				function = "spi0";