diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt')
-rw-r--r-- | Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt | 50 |
1 files changed, 0 insertions, 50 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt b/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt deleted file mode 100644 index 07c59f301b31..000000000000 --- a/Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt +++ /dev/null @@ -1,50 +0,0 @@ -* AT91 SAMA5D2 Analog to Digital Converter (ADC) - -Required properties: - - compatible: Should be "atmel,sama5d2-adc" or "microchip,sam9x60-adc". - - reg: Should contain ADC registers location and length. - - interrupts: Should contain the IRQ line for the ADC. - - clocks: phandle to device clock. - - clock-names: Must be "adc_clk". - - vref-supply: Supply used as reference for conversions. - - vddana-supply: Supply for the adc device. - - atmel,min-sample-rate-hz: Minimum sampling rate, it depends on SoC. - - atmel,max-sample-rate-hz: Maximum sampling rate, it depends on SoC. - - atmel,startup-time-ms: Startup time expressed in ms, it depends on SoC. - - atmel,trigger-edge-type: One of possible edge types for the ADTRG hardware - trigger pin. When the specific edge type is detected, the conversion will - start. Possible values are rising, falling, or both. - This property uses the IRQ edge types values: IRQ_TYPE_EDGE_RISING , - IRQ_TYPE_EDGE_FALLING or IRQ_TYPE_EDGE_BOTH - -Optional properties: - - dmas: Phandle to dma channel for the ADC. - - dma-names: Must be "rx" when dmas property is being used. - See ../../dma/dma.txt for details. - - #io-channel-cells: in case consumer drivers are attached, this must be 1. - See <Documentation/devicetree/bindings/iio/iio-bindings.txt> for details. - -Properties for consumer drivers: - - Consumer drivers can be connected to this producer device, as specified - in <Documentation/devicetree/bindings/iio/iio-bindings.txt> - - Channels exposed are specified in: - <dt-bindings/iio/adc/at91-sama5d2_adc.txt> - -Example: - -adc: adc@fc030000 { - compatible = "atmel,sama5d2-adc"; - reg = <0xfc030000 0x100>; - interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>; - clocks = <&adc_clk>; - clock-names = "adc_clk"; - atmel,min-sample-rate-hz = <200000>; - atmel,max-sample-rate-hz = <20000000>; - atmel,startup-time-ms = <4>; - vddana-supply = <&vdd_3v3_lp_reg>; - vref-supply = <&vdd_3v3_lp_reg>; - atmel,trigger-edge-type = <IRQ_TYPE_EDGE_BOTH>; - dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(25))>; - dma-names = "rx"; - #io-channel-cells = <1>; -} |