diff options
Diffstat (limited to 'arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi | 13 |
1 files changed, 5 insertions, 8 deletions
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi index 702d87621bb4..88321b5b0693 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi @@ -56,7 +56,11 @@ hdmi_connector: hdmi-connector { compatible = "hdmi-connector"; ddc-i2c-bus = <&i2c2>; + /* Verdin PWM_3_DSI (SODIMM 19) */ + hpd-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; label = "hdmi"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm_3_dsi_hpd_gpio>; type = "a"; status = "disabled"; }; @@ -359,7 +363,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pmic>; reg = <0x25>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC @@ -599,7 +602,7 @@ hdmi_lontium_lt8912: hdmi@48 { compatible = "lontium,lt8912b"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>; + pinctrl-0 = <&pinctrl_gpio_10_dsi>; reg = <0x48>; /* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */ /* Verdin GPIO_10_DSI (SODIMM 21) */ @@ -654,10 +657,6 @@ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; assigned-clock-rates = <10000000>, <250000000>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, - <&clk IMX8MM_CLK_PCIE1_AUX>, - <&clk IMX8MM_CLK_PCIE1_PHY>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; /* PCIE_1_RESET# (SODIMM 244) */ @@ -742,7 +741,6 @@ adp-disable; dr_mode = "otg"; hnp-disable; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; srp-disable; @@ -752,7 +750,6 @@ /* Verdin USB_2 */ &usbotg2 { dr_mode = "host"; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; vbus-supply = <®_usb_otg2_vbus>; |