9 files changed, 783 insertions, 49 deletions

diff --git a/drivers/tty/serial/8250/8250_dfl.c b/drivers/tty/serial/8250/8250_dfl.c
new file mode 100644
index 000000000000..6c5ff019df4b
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_dfl.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for FPGA UART
+ *
+ * Copyright (C) 2022 Intel Corporation.
+ *
+ * Authors:
+ *   Ananda Ravuri <ananda.ravuri@intel.com>
+ *   Matthew Gerlach <matthew.gerlach@linux.intel.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/device.h>
+#include <linux/dfl.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/types.h>
+
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+
+#define DFHv1_PARAM_ID_CLK_FRQ    0x2
+#define DFHv1_PARAM_ID_FIFO_LEN   0x3
+
+#define DFHv1_PARAM_ID_REG_LAYOUT	0x4
+#define DFHv1_PARAM_REG_LAYOUT_WIDTH	GENMASK_ULL(63, 32)
+#define DFHv1_PARAM_REG_LAYOUT_SHIFT	GENMASK_ULL(31, 0)
+
+struct dfl_uart {
+	int line;
+};
+
+static int dfh_get_u64_param_val(struct dfl_device *dfl_dev, int param_id, u64 *pval)
+{
+	size_t psize;
+	u64 *p;
+
+	p = dfh_find_param(dfl_dev, param_id, &psize);
+	if (IS_ERR(p))
+		return PTR_ERR(p);
+
+	if (psize != sizeof(*pval))
+		return -EINVAL;
+
+	*pval = *p;
+
+	return 0;
+}
+
+static int dfl_uart_get_params(struct dfl_device *dfl_dev, struct uart_8250_port *uart)
+{
+	struct device *dev = &dfl_dev->dev;
+	u64 fifo_len, clk_freq, reg_layout;
+	u32 reg_width;
+	int ret;
+
+	ret = dfh_get_u64_param_val(dfl_dev, DFHv1_PARAM_ID_CLK_FRQ, &clk_freq);
+	if (ret)
+		return dev_err_probe(dev, ret, "missing CLK_FRQ param\n");
+
+	uart->port.uartclk = clk_freq;
+
+	ret = dfh_get_u64_param_val(dfl_dev, DFHv1_PARAM_ID_FIFO_LEN, &fifo_len);
+	if (ret)
+		return dev_err_probe(dev, ret, "missing FIFO_LEN param\n");
+
+	switch (fifo_len) {
+	case 32:
+		uart->port.type = PORT_ALTR_16550_F32;
+		break;
+
+	case 64:
+		uart->port.type = PORT_ALTR_16550_F64;
+		break;
+
+	case 128:
+		uart->port.type = PORT_ALTR_16550_F128;
+		break;
+
+	default:
+		return dev_err_probe(dev, -EINVAL, "unsupported FIFO_LEN %llu\n", fifo_len);
+	}
+
+	ret = dfh_get_u64_param_val(dfl_dev, DFHv1_PARAM_ID_REG_LAYOUT, &reg_layout);
+	if (ret)
+		return dev_err_probe(dev, ret, "missing REG_LAYOUT param\n");
+
+	uart->port.regshift = FIELD_GET(DFHv1_PARAM_REG_LAYOUT_SHIFT, reg_layout);
+	reg_width = FIELD_GET(DFHv1_PARAM_REG_LAYOUT_WIDTH, reg_layout);
+	switch (reg_width) {
+	case 4:
+		uart->port.iotype = UPIO_MEM32;
+		break;
+
+	case 2:
+		uart->port.iotype = UPIO_MEM16;
+		break;
+
+	default:
+		return dev_err_probe(dev, -EINVAL, "unsupported reg-width %u\n", reg_width);
+
+	}
+
+	return 0;
+}
+
+static int dfl_uart_probe(struct dfl_device *dfl_dev)
+{
+	struct device *dev = &dfl_dev->dev;
+	struct uart_8250_port uart = { };
+	struct dfl_uart *dfluart;
+	int ret;
+
+	uart.port.flags = UPF_IOREMAP;
+	uart.port.mapbase = dfl_dev->mmio_res.start;
+	uart.port.mapsize = resource_size(&dfl_dev->mmio_res);
+
+	ret = dfl_uart_get_params(dfl_dev, &uart);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "failed uart feature walk\n");
+
+	if (dfl_dev->num_irqs == 1)
+		uart.port.irq = dfl_dev->irqs[0];
+
+	dfluart = devm_kzalloc(dev, sizeof(*dfluart), GFP_KERNEL);
+	if (!dfluart)
+		return -ENOMEM;
+
+	dfluart->line = serial8250_register_8250_port(&uart);
+	if (dfluart->line < 0)
+		return dev_err_probe(dev, dfluart->line, "unable to register 8250 port.\n");
+
+	dev_set_drvdata(dev, dfluart);
+
+	return 0;
+}
+
+static void dfl_uart_remove(struct dfl_device *dfl_dev)
+{
+	struct dfl_uart *dfluart = dev_get_drvdata(&dfl_dev->dev);
+
+	serial8250_unregister_port(dfluart->line);
+}
+
+#define FME_FEATURE_ID_UART 0x24
+
+static const struct dfl_device_id dfl_uart_ids[] = {
+	{ FME_ID, FME_FEATURE_ID_UART },
+	{ }
+};
+MODULE_DEVICE_TABLE(dfl, dfl_uart_ids);
+
+static struct dfl_driver dfl_uart_driver = {
+	.drv = {
+		.name = "dfl-uart",
+	},
+	.id_table = dfl_uart_ids,
+	.probe = dfl_uart_probe,
+	.remove = dfl_uart_remove,
+};
+module_dfl_driver(dfl_uart_driver);
+
+MODULE_DESCRIPTION("DFL Intel UART driver");
+MODULE_AUTHOR("Intel Corporation");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
index f271becfc46c..0ebde0ab8167 100644
--- a/drivers/tty/serial/8250/8250_early.c
+++ b/drivers/tty/serial/8250/8250_early.c
@@ -136,11 +136,11 @@ static void __init init_port(struct earlycon_device *device)
 	unsigned char c;
 	unsigned int ier;
 
-	serial8250_early_out(port, UART_LCR, 0x3);	/* 8n1 */
+	serial8250_early_out(port, UART_LCR, UART_LCR_WLEN8);		/* 8n1 */
 	ier = serial8250_early_in(port, UART_IER);
 	serial8250_early_out(port, UART_IER, ier & UART_IER_UUE); /* no interrupt */
 	serial8250_early_out(port, UART_FCR, 0);	/* no fifo */
-	serial8250_early_out(port, UART_MCR, 0x3);	/* DTR + RTS */
+	serial8250_early_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
 
 	if (port->uartclk) {
 		divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * device->baud);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 8e9f247590bd..c55be6fda0ca 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -24,6 +24,7 @@
 #include <asm/io.h>
 
 #include "8250.h"
+#include "8250_pcilib.h"
 
 /*
  * init function returns:
@@ -89,28 +90,7 @@ static int
 setup_port(struct serial_private *priv, struct uart_8250_port *port,
 	   u8 bar, unsigned int offset, int regshift)
 {
-	struct pci_dev *dev = priv->dev;
-
-	if (bar >= PCI_STD_NUM_BARS)
-		return -EINVAL;
-
-	if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
-		if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
-			return -ENOMEM;
-
-		port->port.iotype = UPIO_MEM;
-		port->port.iobase = 0;
-		port->port.mapbase = pci_resource_start(dev, bar) + offset;
-		port->port.membase = pcim_iomap_table(dev)[bar] + offset;
-		port->port.regshift = regshift;
-	} else {
-		port->port.iotype = UPIO_PORT;
-		port->port.iobase = pci_resource_start(dev, bar) + offset;
-		port->port.mapbase = 0;
-		port->port.membase = NULL;
-		port->port.regshift = 0;
-	}
-	return 0;
+	return serial8250_pci_setup_port(priv->dev, port, bar, offset, regshift);
 }
 
 /*
@@ -5757,3 +5737,4 @@ module_pci_driver(serial_pci_driver);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Generic 8250/16x50 PCI serial probe module");
 MODULE_DEVICE_TABLE(pci, serial_pci_tbl);
+MODULE_IMPORT_NS(SERIAL_8250_PCI);
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
new file mode 100644
index 000000000000..a3b25779d921
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -0,0 +1,494 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Probe module for 8250/16550-type MCHP PCI serial ports.
+ *
+ *  Based on drivers/tty/serial/8250/8250_pci.c,
+ *
+ *  Copyright (C) 2022 Microchip Technology Inc., All Rights Reserved.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/units.h>
+#include <linux/tty.h>
+
+#include <asm/byteorder.h>
+
+#include "8250.h"
+#include "8250_pcilib.h"
+
+#define PCI_DEVICE_ID_EFAR_PCI12000		0xa002
+#define PCI_DEVICE_ID_EFAR_PCI11010		0xa012
+#define PCI_DEVICE_ID_EFAR_PCI11101		0xa022
+#define PCI_DEVICE_ID_EFAR_PCI11400		0xa032
+#define PCI_DEVICE_ID_EFAR_PCI11414		0xa042
+
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_4p	0x0001
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p012	0x0002
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013	0x0003
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023	0x0004
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123	0x0005
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p01	0x0006
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02	0x0007
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03	0x0008
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12	0x0009
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13	0x000a
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23	0x000b
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p0	0x000c
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1	0x000d
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2	0x000e
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3	0x000f
+
+#define PCI_SUBDEVICE_ID_EFAR_PCI12000		PCI_DEVICE_ID_EFAR_PCI12000
+#define PCI_SUBDEVICE_ID_EFAR_PCI11010		PCI_DEVICE_ID_EFAR_PCI11010
+#define PCI_SUBDEVICE_ID_EFAR_PCI11101		PCI_DEVICE_ID_EFAR_PCI11101
+#define PCI_SUBDEVICE_ID_EFAR_PCI11400		PCI_DEVICE_ID_EFAR_PCI11400
+#define PCI_SUBDEVICE_ID_EFAR_PCI11414		PCI_DEVICE_ID_EFAR_PCI11414
+
+#define UART_ACTV_REG				0x11
+#define UART_BLOCK_SET_ACTIVE			BIT(0)
+
+#define UART_PCI_CTRL_REG			0x80
+#define UART_PCI_CTRL_SET_MULTIPLE_MSI		BIT(4)
+#define UART_PCI_CTRL_D3_CLK_ENABLE		BIT(0)
+
+#define ADCL_CFG_REG				0x40
+#define ADCL_CFG_POL_SEL			BIT(2)
+#define ADCL_CFG_PIN_SEL			BIT(1)
+#define ADCL_CFG_EN				BIT(0)
+
+#define UART_BIT_SAMPLE_CNT			16
+#define BAUD_CLOCK_DIV_INT_MSK			GENMASK(31, 8)
+#define ADCL_CFG_RTS_DELAY_MASK			GENMASK(11, 8)
+#define UART_CLOCK_DEFAULT			(62500 * HZ_PER_KHZ)
+
+#define UART_WAKE_REG				0x8C
+#define UART_WAKE_MASK_REG			0x90
+#define UART_WAKE_N_PIN				BIT(2)
+#define UART_WAKE_NCTS				BIT(1)
+#define UART_WAKE_INT				BIT(0)
+#define UART_WAKE_SRCS	\
+	(UART_WAKE_N_PIN | UART_WAKE_NCTS | UART_WAKE_INT)
+
+#define UART_BAUD_CLK_DIVISOR_REG		0x54
+
+#define UART_RESET_REG				0x94
+#define UART_RESET_D3_RESET_DISABLE		BIT(16)
+
+#define MAX_PORTS				4
+#define PORT_OFFSET				0x100
+
+static const int logical_to_physical_port_idx[][MAX_PORTS] = {
+	{0,  1,  2,  3}, /* PCI12000, PCI11010, PCI11101, PCI11400, PCI11414 */
+	{0,  1,  2,  3}, /* PCI4p */
+	{0,  1,  2, -1}, /* PCI3p012 */
+	{0,  1,  3, -1}, /* PCI3p013 */
+	{0,  2,  3, -1}, /* PCI3p023 */
+	{1,  2,  3, -1}, /* PCI3p123 */
+	{0,  1, -1, -1}, /* PCI2p01 */
+	{0,  2, -1, -1}, /* PCI2p02 */
+	{0,  3, -1, -1}, /* PCI2p03 */
+	{1,  2, -1, -1}, /* PCI2p12 */
+	{1,  3, -1, -1}, /* PCI2p13 */
+	{2,  3, -1, -1}, /* PCI2p23 */
+	{0, -1, -1, -1}, /* PCI1p0 */
+	{1, -1, -1, -1}, /* PCI1p1 */
+	{2, -1, -1, -1}, /* PCI1p2 */
+	{3, -1, -1, -1}, /* PCI1p3 */
+};
+
+struct pci1xxxx_8250 {
+	unsigned int nr;
+	void __iomem *membase;
+	int line[];
+};
+
+static int pci1xxxx_get_num_ports(struct pci_dev *dev)
+{
+	switch (dev->subsystem_device) {
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p0:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3:
+	case PCI_SUBDEVICE_ID_EFAR_PCI12000:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11010:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11101:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11400:
+	default:
+		return 1;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p01:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23:
+		return 2;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p012:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023:
+		return 3;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_4p:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11414:
+		return 4;
+	}
+}
+
+static unsigned int pci1xxxx_get_divisor(struct uart_port *port,
+					 unsigned int baud, unsigned int *frac)
+{
+	unsigned int quot;
+
+	/*
+	 * Calculate baud rate sampling period in nanoseconds.
+	 * Fractional part x denotes x/255 parts of a nanosecond.
+	 */
+	quot = NSEC_PER_SEC / (baud * UART_BIT_SAMPLE_CNT);
+	*frac = (NSEC_PER_SEC - quot * baud * UART_BIT_SAMPLE_CNT) *
+		  255 / UART_BIT_SAMPLE_CNT / baud;
+
+	return quot;
+}
+
+static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
+				 unsigned int quot, unsigned int frac)
+{
+	writel(FIELD_PREP(BAUD_CLOCK_DIV_INT_MSK, quot) | frac,
+	       port->membase + UART_BAUD_CLK_DIVISOR_REG);
+}
+
+static int pci1xxxx_rs485_config(struct uart_port *port,
+				 struct ktermios *termios,
+				 struct serial_rs485 *rs485)
+{
+	u32 delay_in_baud_periods;
+	u32 baud_period_in_ns;
+	u32 mode_cfg = 0;
+	u32 clock_div;
+
+	/*
+	 * pci1xxxx's uart hardware supports only RTS delay after
+	 * Tx and in units of bit times to a maximum of 15
+	 */
+	if (rs485->flags & SER_RS485_ENABLED) {
+		mode_cfg = ADCL_CFG_EN | ADCL_CFG_PIN_SEL;
+
+		if (!(rs485->flags & SER_RS485_RTS_ON_SEND))
+			mode_cfg |= ADCL_CFG_POL_SEL;
+
+		if (rs485->delay_rts_after_send) {
+			clock_div = readl(port->membase + UART_BAUD_CLK_DIVISOR_REG);
+			baud_period_in_ns =
+				FIELD_GET(BAUD_CLOCK_DIV_INT_MSK, clock_div) *
+				UART_BIT_SAMPLE_CNT;
+			delay_in_baud_periods =
+				rs485->delay_rts_after_send * NSEC_PER_MSEC /
+				baud_period_in_ns;
+			delay_in_baud_periods =
+				min_t(u32, delay_in_baud_periods,
+				      FIELD_MAX(ADCL_CFG_RTS_DELAY_MASK));
+			mode_cfg |= FIELD_PREP(ADCL_CFG_RTS_DELAY_MASK,
+					   delay_in_baud_periods);
+			rs485->delay_rts_after_send =
+				baud_period_in_ns * delay_in_baud_periods /
+				NSEC_PER_MSEC;
+		}
+	}
+	writel(mode_cfg, port->membase + ADCL_CFG_REG);
+	return 0;
+}
+
+static const struct serial_rs485 pci1xxxx_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
+		 SER_RS485_RTS_AFTER_SEND,
+	.delay_rts_after_send = 1,
+	/* Delay RTS before send is not supported */
+};
+
+static bool pci1xxxx_port_suspend(int line)
+{
+	struct uart_8250_port *up = serial8250_get_port(line);
+	struct uart_port *port = &up->port;
+	struct tty_port *tport = &port->state->port;
+	unsigned long flags;
+	bool ret = false;
+	u8 wakeup_mask;
+
+	mutex_lock(&tport->mutex);
+	if (port->suspended == 0 && port->dev) {
+		wakeup_mask = readb(up->port.membase + UART_WAKE_MASK_REG);
+
+		spin_lock_irqsave(&port->lock, flags);
+		port->mctrl &= ~TIOCM_OUT2;
+		port->ops->set_mctrl(port, port->mctrl);
+		spin_unlock_irqrestore(&port->lock, flags);
+
+		ret = (wakeup_mask & UART_WAKE_SRCS) != UART_WAKE_SRCS;
+	}
+
+	writeb(UART_WAKE_SRCS, port->membase + UART_WAKE_REG);
+	mutex_unlock(&tport->mutex);
+
+	return ret;
+}
+
+static void pci1xxxx_port_resume(int line)
+{
+	struct uart_8250_port *up = serial8250_get_port(line);
+	struct uart_port *port = &up->port;
+	struct tty_port *tport = &port->state->port;
+	unsigned long flags;
+
+	mutex_lock(&tport->mutex);
+	writeb(UART_BLOCK_SET_ACTIVE, port->membase + UART_ACTV_REG);
+	writeb(UART_WAKE_SRCS, port->membase + UART_WAKE_REG);
+
+	if (port->suspended == 0) {
+		spin_lock_irqsave(&port->lock, flags);
+		port->mctrl |= TIOCM_OUT2;
+		port->ops->set_mctrl(port, port->mctrl);
+		spin_unlock_irqrestore(&port->lock, flags);
+	}
+	mutex_unlock(&tport->mutex);
+}
+
+static int pci1xxxx_suspend(struct device *dev)
+{
+	struct pci1xxxx_8250 *priv = dev_get_drvdata(dev);
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	bool wakeup = false;
+	unsigned int data;
+	void __iomem *p;
+	int i;
+
+	for (i = 0; i < priv->nr; i++) {
+		if (priv->line[i] >= 0) {
+			serial8250_suspend_port(priv->line[i]);
+			wakeup |= pci1xxxx_port_suspend(priv->line[i]);
+		}
+	}
+
+	p = pci_ioremap_bar(pcidev, 0);
+	if (!p) {
+		dev_err(dev, "remapping of bar 0 memory failed");
+		return -ENOMEM;
+	}
+
+	data = readl(p + UART_RESET_REG);
+	writel(data | UART_RESET_D3_RESET_DISABLE, p + UART_RESET_REG);
+
+	if (wakeup)
+		writeb(UART_PCI_CTRL_D3_CLK_ENABLE, p + UART_PCI_CTRL_REG);
+
+	iounmap(p);
+	device_set_wakeup_enable(dev, true);
+	pci_wake_from_d3(pcidev, true);
+
+	return 0;
+}
+
+static int pci1xxxx_resume(struct device *dev)
+{
+	struct pci1xxxx_8250 *priv = dev_get_drvdata(dev);
+	struct pci_dev *pcidev = to_pci_dev(dev);
+	unsigned int data;
+	void __iomem *p;
+	int i;
+
+	p = pci_ioremap_bar(pcidev, 0);
+	if (!p) {
+		dev_err(dev, "remapping of bar 0 memory failed");
+		return -ENOMEM;
+	}
+
+	data = readl(p + UART_RESET_REG);
+	writel(data & ~UART_RESET_D3_RESET_DISABLE, p + UART_RESET_REG);
+	iounmap(p);
+
+	for (i = 0; i < priv->nr; i++) {
+		if (priv->line[i] >= 0) {
+			pci1xxxx_port_resume(priv->line[i]);
+			serial8250_resume_port(priv->line[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int pci1xxxx_setup(struct pci_dev *pdev,
+			  struct uart_8250_port *port, int port_idx)
+{
+	int ret;
+
+	port->port.flags |= UPF_FIXED_TYPE | UPF_SKIP_TEST;
+	port->port.type = PORT_MCHP16550A;
+	port->port.set_termios = serial8250_do_set_termios;
+	port->port.get_divisor = pci1xxxx_get_divisor;
+	port->port.set_divisor = pci1xxxx_set_divisor;
+	port->port.rs485_config = pci1xxxx_rs485_config;
+	port->port.rs485_supported = pci1xxxx_rs485_supported;
+
+	ret = serial8250_pci_setup_port(pdev, port, 0, PORT_OFFSET * port_idx, 0);
+	if (ret < 0)
+		return ret;
+
+	writeb(UART_BLOCK_SET_ACTIVE, port->port.membase + UART_ACTV_REG);
+	writeb(UART_WAKE_SRCS, port->port.membase + UART_WAKE_REG);
+	writeb(UART_WAKE_N_PIN, port->port.membase + UART_WAKE_MASK_REG);
+
+	return 0;
+}
+
+static unsigned int pci1xxxx_get_max_port(int subsys_dev)
+{
+	unsigned int i = MAX_PORTS;
+
+	if (subsys_dev < ARRAY_SIZE(logical_to_physical_port_idx))
+		while (i--) {
+			if (logical_to_physical_port_idx[subsys_dev][i] != -1)
+				return logical_to_physical_port_idx[subsys_dev][i] + 1;
+		}
+
+	if (subsys_dev == PCI_SUBDEVICE_ID_EFAR_PCI11414)
+		return 4;
+
+	return 1;
+}
+
+static int pci1xxxx_logical_to_physical_port_translate(int subsys_dev, int port)
+{
+	if (subsys_dev < ARRAY_SIZE(logical_to_physical_port_idx))
+		return logical_to_physical_port_idx[subsys_dev][port];
+
+	return logical_to_physical_port_idx[0][port];
+}
+
+static int pci1xxxx_serial_probe(struct pci_dev *pdev,
+				 const struct pci_device_id *id)
+{
+	struct device *dev = &pdev->dev;
+	struct pci1xxxx_8250 *priv;
+	struct uart_8250_port uart;
+	unsigned int max_vec_reqd;
+	unsigned int nr_ports, i;
+	int num_vectors;
+	int subsys_dev;
+	int port_idx;
+	int rc;
+
+	rc = pcim_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	nr_ports = pci1xxxx_get_num_ports(pdev);
+
+	priv = devm_kzalloc(dev, struct_size(priv, line, nr_ports), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->membase = pci_ioremap_bar(pdev, 0);
+	if (!priv->membase)
+		return -ENOMEM;
+
+	pci_set_master(pdev);
+
+	priv->nr = nr_ports;
+
+	subsys_dev = pdev->subsystem_device;
+	max_vec_reqd = pci1xxxx_get_max_port(subsys_dev);
+
+	num_vectors = pci_alloc_irq_vectors(pdev, 1, max_vec_reqd, PCI_IRQ_ALL_TYPES);
+	if (num_vectors < 0) {
+		pci_iounmap(pdev, priv->membase);
+		return num_vectors;
+	}
+
+	memset(&uart, 0, sizeof(uart));
+	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT;
+	uart.port.uartclk = UART_CLOCK_DEFAULT;
+	uart.port.dev = dev;
+
+	if (num_vectors == max_vec_reqd)
+		writeb(UART_PCI_CTRL_SET_MULTIPLE_MSI, priv->membase + UART_PCI_CTRL_REG);
+
+	for (i = 0; i < nr_ports; i++) {
+		priv->line[i] = -ENODEV;
+
+		port_idx = pci1xxxx_logical_to_physical_port_translate(subsys_dev, i);
+
+		if (num_vectors == max_vec_reqd)
+			uart.port.irq = pci_irq_vector(pdev, port_idx);
+		else
+			uart.port.irq = pci_irq_vector(pdev, 0);
+
+		rc = pci1xxxx_setup(pdev, &uart, port_idx);
+		if (rc) {
+			dev_warn(dev, "Failed to setup port %u\n", i);
+			continue;
+		}
+
+		priv->line[i] = serial8250_register_8250_port(&uart);
+		if (priv->line[i] < 0) {
+			dev_warn(dev,
+				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
+				uart.port.iobase, uart.port.irq, uart.port.iotype,
+				priv->line[i]);
+		}
+	}
+
+	pci_set_drvdata(pdev, priv);
+
+	return 0;
+}
+
+static void pci1xxxx_serial_remove(struct pci_dev *dev)
+{
+	struct pci1xxxx_8250 *priv = pci_get_drvdata(dev);
+	unsigned int i;
+
+	for (i = 0; i < priv->nr; i++) {
+		if (priv->line[i] >= 0)
+			serial8250_unregister_port(priv->line[i]);
+	}
+
+	pci_free_irq_vectors(dev);
+	pci_iounmap(dev, priv->membase);
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(pci1xxxx_pm_ops, pci1xxxx_suspend, pci1xxxx_resume);
+
+static const struct pci_device_id pci1xxxx_pci_tbl[] = {
+	{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11010) },
+	{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11101) },
+	{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11400) },
+	{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI11414) },
+	{ PCI_VDEVICE(EFAR, PCI_DEVICE_ID_EFAR_PCI12000) },
+	{}
+};
+MODULE_DEVICE_TABLE(pci, pci1xxxx_pci_tbl);
+
+static struct pci_driver pci1xxxx_pci_driver = {
+	.name = "pci1xxxx serial",
+	.probe = pci1xxxx_serial_probe,
+	.remove = pci1xxxx_serial_remove,
+	.driver = {
+		.pm     = pm_sleep_ptr(&pci1xxxx_pm_ops),
+	},
+	.id_table = pci1xxxx_pci_tbl,
+};
+module_pci_driver(pci1xxxx_pci_driver);
+
+static_assert((ARRAY_SIZE(logical_to_physical_port_idx) == PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3 + 1));
+
+MODULE_IMPORT_NS(SERIAL_8250_PCI);
+MODULE_DESCRIPTION("Microchip Technology Inc. PCIe to UART module");
+MODULE_AUTHOR("Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>");
+MODULE_AUTHOR("Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_pcilib.c b/drivers/tty/serial/8250/8250_pcilib.c
new file mode 100644
index 000000000000..d234e9194feb
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pcilib.c
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * 8250 PCI library.
+ *
+ * Copyright (C) 2001 Russell King, All Rights Reserved.
+ */
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/pci.h>
+#include <linux/types.h>
+
+#include "8250.h"
+#include "8250_pcilib.h"
+
+int serial8250_pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port,
+		   u8 bar, unsigned int offset, int regshift)
+{
+	if (bar >= PCI_STD_NUM_BARS)
+		return -EINVAL;
+
+	if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
+		if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
+			return -ENOMEM;
+
+		port->port.iotype = UPIO_MEM;
+		port->port.iobase = 0;
+		port->port.mapbase = pci_resource_start(dev, bar) + offset;
+		port->port.membase = pcim_iomap_table(dev)[bar] + offset;
+		port->port.regshift = regshift;
+	} else {
+		port->port.iotype = UPIO_PORT;
+		port->port.iobase = pci_resource_start(dev, bar) + offset;
+		port->port.mapbase = 0;
+		port->port.membase = NULL;
+		port->port.regshift = 0;
+	}
+	return 0;
+}
+EXPORT_SYMBOL_NS_GPL(serial8250_pci_setup_port, SERIAL_8250_PCI);
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_pcilib.h b/drivers/tty/serial/8250/8250_pcilib.h
new file mode 100644
index 000000000000..1aaf1b50ce9c
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pcilib.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * 8250 PCI library header file.
+ *
+ * Copyright (C) 2001 Russell King, All Rights Reserved.
+ */
+
+#include <linux/types.h>
+
+struct pci_dev;
+
+struct uart_8250_port;
+
+int serial8250_pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port, u8 bar,
+		   unsigned int offset, int regshift);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index beba8f38b3dc..fa43df05342b 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -313,6 +313,14 @@ static const struct serial8250_config uart_config[] = {
 		.rxtrig_bytes	= {1, 4, 8, 14},
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_MCHP16550A] = {
+		.name           = "MCHP16550A",
+		.fifo_size      = 256,
+		.tx_loadsz      = 256,
+		.fcr            = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01,
+		.rxtrig_bytes   = {2, 66, 130, 194},
+		.flags          = UART_CAP_FIFO,
+	},
 };
 
 /* Uart divisor latch read */
@@ -1050,11 +1058,12 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 			serial_out(up, UART_LCR, 0);
 			serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 				   UART_FCR7_64BYTE);
-			status1 = serial_in(up, UART_IIR) >> 5;
+			status1 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO |
+							     UART_IIR_FIFO_ENABLED);
 			serial_out(up, UART_FCR, 0);
 			serial_out(up, UART_LCR, 0);
 
-			if (status1 == 7)
+			if (status1 == (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED))
 				up->port.type = PORT_16550A_FSL64;
 			else
 				DEBUG_AUTOCONF("Motorola 8xxx DUART ");
@@ -1122,17 +1131,20 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 	 */
 	serial_out(up, UART_LCR, 0);
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
-	status1 = serial_in(up, UART_IIR) >> 5;
+	status1 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED);
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+
 	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
-	status2 = serial_in(up, UART_IIR) >> 5;
+	status2 = serial_in(up, UART_IIR) & (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED);
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+
 	serial_out(up, UART_LCR, 0);
 
 	DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
 
-	if (status1 == 6 && status2 == 7) {
+	if (status1 == UART_IIR_FIFO_ENABLED_16550A &&
+	    status2 == (UART_IIR_64BYTE_FIFO | UART_IIR_FIFO_ENABLED_16550A)) {
 		up->port.type = PORT_16750;
 		up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
 		return;
@@ -1236,14 +1248,14 @@ static void autoconfig(struct uart_8250_port *up)
 		 * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
 		 * 16C754B) allow only to modify them if an EFR bit is set.
 		 */
-		scratch2 = serial_in(up, UART_IER) & 0x0f;
-		serial_out(up, UART_IER, 0x0F);
+		scratch2 = serial_in(up, UART_IER) & UART_IER_ALL_INTR;
+		serial_out(up, UART_IER, UART_IER_ALL_INTR);
 #ifdef __i386__
 		outb(0, 0x080);
 #endif
-		scratch3 = serial_in(up, UART_IER) & 0x0f;
+		scratch3 = serial_in(up, UART_IER) & UART_IER_ALL_INTR;
 		serial_out(up, UART_IER, scratch);
-		if (scratch2 != 0 || scratch3 != 0x0F) {
+		if (scratch2 != 0 || scratch3 != UART_IER_ALL_INTR) {
 			/*
 			 * We failed; there's nothing here
 			 */
@@ -1267,10 +1279,10 @@ static void autoconfig(struct uart_8250_port *up)
 	 * that conflicts with COM 1-4 --- we hope!
 	 */
 	if (!(port->flags & UPF_SKIP_TEST)) {
-		serial8250_out_MCR(up, UART_MCR_LOOP | 0x0A);
-		status1 = serial_in(up, UART_MSR) & 0xF0;
+		serial8250_out_MCR(up, UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_RTS);
+		status1 = serial_in(up, UART_MSR) & UART_MSR_STATUS_BITS;
 		serial8250_out_MCR(up, save_mcr);
-		if (status1 != 0x90) {
+		if (status1 != (UART_MSR_DCD | UART_MSR_CTS)) {
 			spin_unlock_irqrestore(&port->lock, flags);
 			DEBUG_AUTOCONF("LOOP test failed (%02x) ",
 				       status1);
@@ -1293,22 +1305,19 @@ static void autoconfig(struct uart_8250_port *up)
 
 	serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 
-	/* Assign this as it is to truncate any bits above 7.  */
-	scratch = serial_in(up, UART_IIR);
-
-	switch (scratch >> 6) {
-	case 0:
+	switch (serial_in(up, UART_IIR) & UART_IIR_FIFO_ENABLED) {
+	case UART_IIR_FIFO_ENABLED_8250:
 		autoconfig_8250(up);
 		break;
-	case 1:
-		port->type = PORT_UNKNOWN;
-		break;
-	case 2:
+	case UART_IIR_FIFO_ENABLED_16550:
 		port->type = PORT_16550;
 		break;
-	case 3:
+	case UART_IIR_FIFO_ENABLED_16550A:
 		autoconfig_16550a(up);
 		break;
+	default:
+		port->type = PORT_UNKNOWN;
+		break;
 	}
 
 #ifdef CONFIG_SERIAL_8250_RSA
@@ -1394,7 +1403,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
 		serial8250_out_MCR(up,
 			UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
 	}
-	serial_out(up, UART_IER, 0x0f);	/* enable all intrs */
+	serial_out(up, UART_IER, UART_IER_ALL_INTR);
 	serial_in(up, UART_LSR);
 	serial_in(up, UART_RX);
 	serial_in(up, UART_IIR);
@@ -1511,8 +1520,6 @@ static inline void __stop_tx(struct uart_8250_port *p)
 		u16 lsr = serial_lsr_in(p);
 		u64 stop_delay = 0;
 
-		p->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
-
 		if (!(lsr & UART_LSR_THRE))
 			return;
 		/*
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index b0f62345bc84..978dc196c29b 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -129,9 +129,13 @@ config SERIAL_8250_DMA
 	  This builds DMA support that can be used with 8250/16650
 	  compatible UART controllers that support DMA signaling.
 
+config SERIAL_8250_PCILIB
+	bool
+
 config SERIAL_8250_PCI
 	tristate "8250/16550 PCI device support"
 	depends on SERIAL_8250 && PCI
+	select SERIAL_8250_PCILIB
 	default SERIAL_8250
 	help
 	  This builds standard PCI serial support. You may be able to
@@ -291,6 +295,17 @@ config SERIAL_8250_HUB6
 	  To compile this driver as a module, choose M here: the module
 	  will be called 8250_hub6.
 
+config SERIAL_8250_PCI1XXXX
+	tristate "Microchip 8250 based serial port"
+	depends on SERIAL_8250 && PCI
+	select SERIAL_8250_PCILIB
+	default SERIAL_8250
+	help
+	 Select this option if you have a setup with Microchip PCIe
+	 Switch with serial port enabled and wish to enable 8250
+	 serial driver for the serial interface. This driver support
+	 will ensure to support baud rates upto 1.5Mpbs.
+
 #
 # Misc. options/drivers.
 #
@@ -370,6 +385,18 @@ config SERIAL_8250_FSL
 	  erratum for Freescale 16550 UARTs in the 8250 driver. It also
 	  enables support for ACPI enumeration.
 
+config SERIAL_8250_DFL
+	tristate "DFL bus driver for Altera 16550 UART"
+	depends on SERIAL_8250 && FPGA_DFL
+	help
+	  This option enables support for a Device Feature List (DFL) bus
+	  driver for the Altera 16550 UART. One or more Altera 16550 UARTs
+	  can be instantiated in a FPGA and then be discovered during
+	  enumeration of the DFL bus.
+
+	  To compile this driver as a module, chose M here: the
+	  module will be called 8250_dfl.
+
 config SERIAL_8250_DW
 	tristate "Support for Synopsys DesignWare 8250 quirks"
 	depends on SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 1615bfdde2a0..4fc2fc1f41b6 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_SERIAL_8250)		+= 8250.o 8250_base.o
 8250_base-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
 8250_base-$(CONFIG_SERIAL_8250_DWLIB)	+= 8250_dwlib.o
 8250_base-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
+8250_base-$(CONFIG_SERIAL_8250_PCILIB)	+= 8250_pcilib.o
 obj-$(CONFIG_SERIAL_8250_PARISC)	+= 8250_parisc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
 obj-$(CONFIG_SERIAL_8250_EXAR)		+= 8250_exar.o
@@ -26,8 +27,10 @@ obj-$(CONFIG_SERIAL_8250_ACCENT)	+= 8250_accent.o
 obj-$(CONFIG_SERIAL_8250_BOCA)		+= 8250_boca.o
 obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)	+= 8250_exar_st16c554.o
 obj-$(CONFIG_SERIAL_8250_HUB6)		+= 8250_hub6.o
+obj-$(CONFIG_SERIAL_8250_PCI1XXXX)	+= 8250_pci1xxxx.o
 obj-$(CONFIG_SERIAL_8250_FSL)		+= 8250_fsl.o
 obj-$(CONFIG_SERIAL_8250_MEN_MCB)	+= 8250_men_mcb.o
+obj-$(CONFIG_SERIAL_8250_DFL)		+= 8250_dfl.o
 obj-$(CONFIG_SERIAL_8250_DW)		+= 8250_dw.o
 obj-$(CONFIG_SERIAL_8250_EM)		+= 8250_em.o
 obj-$(CONFIG_SERIAL_8250_IOC3)		+= 8250_ioc3.o