summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
AgeCommit message (Collapse)AuthorFilesLines
10 daysMerge tag 'v6.10-rockchip-dtsfixes1' of ↵Arnd Bergmann1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes Apart from the regular dts fixes for wrong addresses, missing or wrong properties, this reverts the previous move away from cd-gpios to the mmc-controller's internal card-detect. With this change applied, it was reported that boards could not detect card anymore, so this go reverted of course. * tag 'v6.10-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: arm64: dts: rockchip: Add sound-dai-cells for RK3368 arm64: dts: rockchip: Fix the i2c address of es8316 on Cool Pi 4B arm64: dts: rockchip: fix PMIC interrupt pin on ROCK Pi E arm64: dts: rockchip: make poweroff(8) work on Radxa ROCK 5A Revert "arm64: dts: rockchip: remove redundant cd-gpios from rk3588 sdmmc nodes" ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi node arm64: dts: rockchip: Fix the value of `dlg,jack-det-rate` mismatch on rk3399-gru arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger arm64: dts: rockchip: Rename LED related pinctrl nodes on rk3308-rock-pi-s arm64: dts: rockchip: Fix SD NAND and eMMC init on rk3308-rock-pi-s arm64: dts: rockchip: Fix rk3308 codec@ff560000 reset-names arm64: dts: rockchip: Fix the DCDC_REG2 minimum voltage on Quartz64 Model B Link: https://lore.kernel.org/r/10237789.nnTZe4vzsl@diego Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-06-17ARM: dts: rockchip: rk3066a: add #sound-dai-cells to hdmi nodeJohan Jonker1-0/+1
'#sound-dai-cells' is required to properly interpret the list of DAI specified in the 'sound-dai' property, so add them to the 'hdmi' node for 'rk3066a.dtsi'. Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes") Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2024-06-15arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting nodeLiu Ying2-3/+5
We cannot use /delete-node/ directive to delete a node in a DT overlay. The node won't be deleted effectively. Instead, set the node's status property to "disabled" to achieve something similar. Fixes: eeb403df953f ("ARM: dts: imx53-qsb: add support for the HDMI expander") Signed-off-by: Liu Ying <victor.liu@nxp.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2024-05-21Merge tag 'soc-dt-late-6.10' of ↵Linus Torvalds20-826/+4449
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull more SoC devicetree updates from Arnd Bergmann: "This is a follow-up to an earlier pull request for device tree changes, as three platform maintainers sent their contents too late to be included in the main set, but had not caused any further problems since then: - The Amlogic platform now containts support for two new SoC types, the A4 and A5 chips for audio applications. Both come with a reference board, and one more dts file gets addded for the combination of the MNT Reform Laptop with the BPI-CM4 CPU module - The ASpeed platform adds support for six addititional server platforms that use ast2500 or ast2600 as their BMC, while another one gets removed - The RISC-V platforms from Microchip, Starfive and and T-HEAD get additional features for existing hardware, plus the addition of the Milk-V Mars based on the StarFive VisionFive v2 board" * tag 'soc-dt-late-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (76 commits) riscv: dts: microchip: add pac1934 power-monitor to icicle riscv: dts: thead: Fix node ordering in TH1520 device tree ARM: dts: aspeed: Add ASRock E3C256D4I BMC dt-bindings: arm: aspeed: document ASRock E3C256D4I dt-bindings: trivial-devices: add isil,isl69269 ARM: dts: aspeed: x4tf: Add dts for asus x4tf project dt-bindings: arm: aspeed: add ASUS X4TF board ARM: dts: aspeed: Remove Facebook Cloudripper dts ARM: dts: aspeed: drop unused ref_voltage ADC property ARM: dts: aspeed: harma: correct Mellanox multi-host property ARM: dts: aspeed: yosemitev2: correct Mellanox multi-host property ARM: dts: aspeed: yosemite4: correct Mellanox multi-host property ARM: dts: aspeed: greatlakes: correct Mellanox multi-host property ARM: dts: aspeed: Modify I2C bus configuration ARM: dts: aspeed: Disable unused ADC channels for Asrock X570D4U BMC ARM: dts: aspeed: Modify GPIO table for Asrock X570D4U BMC ARM: dts: aspeed: yosemite4: set bus13 frequency to 100k ARM: dts: Aspeed: Bonnell: Fix NVMe LED labels ARM: dts: aspeed: yosemite4: Enable ipmb device for OCP debug card ARM: dts: aspeed: ahe50dc: Update lm25066 regulator name ...
2024-05-14Merge tag 'irq-core-2024-05-12' of ↵Linus Torvalds2-1/+148
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull interrupt subsystem updates from Thomas Gleixner: "Core code: - Interrupt storm detection for the lockup watchdog: Lockups which are caused by interrupt storms are not easy to debug because there is no information about the events which make the lockup detector trigger. To make this more user friendly, provide an extenstion to interrupt statistics which allows to take snapshots and an interface to retrieve the delta to the snapshot. Use this new mechanism in the watchdog code to do a two stage lockup analysis by taking the snapshot and printing the deltas for the topmost active interrupts on the second trigger. Note: This contains both the interrupt and the watchdog changes as the latter depend on the former obviously. - Avoid summation loops in the /proc/interrupts output and use the global counter when possible - Skip suspended interrupts on CPU hotplug operations to ensure that they are not delivered before the system resumes the device drivers when coming out of suspend. - On CPU hot-unplug interrupts which are affine to the outgoing CPU are migrated to a different CPU in the affinity mask. This can fail when the CPUs have no vectors left. Instead of giving up try to migrate it to any online CPU and thereby breaking the affinity setting in order to prevent a stale device interrupt which targets an offline CPU - The usual small cleanups Driver code: - Support for the RISCV AIA MSI controller - Make the interrupt allocation for the Loongson PCH controller more flexible to prevent vector exhaustion - The usual set of cleanups and fixes all over the place" * tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits) irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc cpuidle: Avoid explicit cpumask allocation on stack irqchip/sifive-plic: Avoid explicit cpumask allocation on stack irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack cpumask: Introduce cpumask_first_and_and() irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown genirq: Reuse irq_is_nmi() genirq/cpuhotplug: Retry with cpu_online_mask when migration fails genirq/cpuhotplug: Skip suspended interrupts when restoring affinity arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251 arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251 ARM: dts: stm32: List exti parent interrupts on stm32mp131 ARM: dts: stm32: List exti parent interrupts on stm32mp151 arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32 irqchip/stm32-exti: Mark events reserved with RIF configuration check irqchip/stm32-exti: Skip secure events irqchip/stm32-exti: Convert driver to standard PM ...
2024-05-13Merge tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds196-3841/+7258
Pull SoC devicetree updates from Arnd Bergmann: "The updates this time are a bit smaller than most times, mainly because it is not totally dominated by new Qualcomm hardware support. Instead, we larger than average updates for Rockchips, NXP, Allwinner and TI. The only two new SoCs this time are both from NXP and are minor variants of already supported ones. The updates for aspeed, amlogic and mediatek came a little late, so I'm saving those for part 2 in a few days if everything turns out fine. New machines this time contain: - two Broadcom SoC based wireless routers from Asus - Five allwinner based consumer devices for gaming, set-top-box and eboot reader applications - Three older phones based on Qualcomm chips, plus the more recent Sony Xperia 1 V - 14 industrial and embedded boards based on NXP i.MX6, i.MX8, layerscape and s32g3 SoCs - six rockchips boards including another handheld game console and a few single-board computers On top of these, we have the usual cleanups for dtc warnings and updates to add more features to already merged machines" * tag 'soc-dt-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (612 commits) arm64: dts: marvell: espressobin-ultra: fix Ethernet Switch unit address arm64: dts: marvell: turris-mox: drop unneeded flash address/size-cells arm64: dts: marvell: eDPU: drop redundant address/size-cells arm64: dts: qcom: pm6150: correct USB VBUS regulator compatible arm64: dts: rockchip: add rk3588 pcie and php IOMMUs arm64: dts: rockchip: enable onboard spi flash for rock-3a arm64: dts: rockchip: add USB-C support to rk3588s-orangepi-5 arm64: dts: rockchip: Enable GPU on Orange Pi 5 arm64: dts: rockchip: enable GPU on khadas-edge2 arm64: dts: rockchip: Add USB3 on Edgeble NCM6A-IO board arm64: dts: rockchip: Support poweroff on Edgeble Neural Compute Module arm64: dts: rockchip: Add Radxa ROCK 3C dt-bindings: arm: rockchip: add Radxa ROCK 3C arm64: dts: exynos: gs101: specify empty clocks for remaining pinctrl arm64: dts: exynos: gs101: specify bus clock for pinctrl_hsi2 arm64: dts: exynos: gs101: specify bus clock for pinctrl_peric[01] arm64: dts: exynos: gs101: specify bus clock for pinctrl (far) alive arm64: dts: Add/fix /memory node unit-addresses arm64: dts: qcom: qcs404: fix bluetooth device address arm64: dts: qcom: sc8280xp-x13s: enable USB MP and fingerprint reader ...
2024-05-02Merge tag 'ti-keystone-dt-for-v6.10' of ↵Arnd Bergmann1-5/+0
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/dt Keystone2 device tree updates for v6.10 Generic Cleanups/Fixes: - Remove custom ti,system-reboot-controller property * tag 'ti-keystone-dt-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux: dt-bindings: arm: keystone: Remove ti,system-reboot-controller property ARM: dts: ti: keystone: k2g: Remove ti,system-reboot-controller property Link: https://lore.kernel.org/r/20240501124309.3cj5b3gjf3cpimut@outsell Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2024-05-02ARM: dts: aspeed: Add ASRock E3C256D4I BMCZev Weiss2-0/+323
Like the E3C246D4I, this is a reasonably affordable off-the-shelf mini-ITX AST2500/Xeon motherboard with good potential as an OpenBMC development platform. Booting the host requires a modicum of eSPI support that's not yet in the mainline kernel, but most other basic BMC functionality is available with this device-tree. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Link: https://lore.kernel.org/r/20240502002836.17862-8-zev@bewilderbeest.net Signed-off-by: Joel Stanley <joel@jms.id.au>
2024-05-01ARM: dts: aspeed: x4tf: Add dts for asus x4tf projectKelly Hung2-0/+582
Base on aspeed-g6.dtsi and can boot into BMC console. Signed-off-by: Kelly Hung <ppighouse@gmail.com> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Link: https://lore.kernel.org/r/20240430045853.3894633-3-Kelly_Hung@asus.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2024-05-01ARM: dts: aspeed: Remove Facebook Cloudripper dtsTao Ren2-545/+0
Remove Facebook Cloudripper dts because the switch platform is not actively maintained (all the units are deprecated). Signed-off-by: Tao Ren <rentao.bupt@gmail.com> Link: https://lore.kernel.org/r/20240411045622.7915-1-rentao.bupt@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: drop unused ref_voltage ADC propertyKrzysztof Kozlowski3-5/+0
Aspeed ADC "ref_voltage" property is neither documented nor used. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240405064624.18997-5-krzysztof.kozlowski@linaro.org Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: harma: correct Mellanox multi-host propertyKrzysztof Kozlowski1-1/+1
"mlx,multi-host" is using incorrect vendor prefix and is not documented. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240405064624.18997-4-krzysztof.kozlowski@linaro.org Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: yosemitev2: correct Mellanox multi-host propertyKrzysztof Kozlowski1-1/+1
"mlx,multi-host" is using incorrect vendor prefix and is not documented. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240405064624.18997-3-krzysztof.kozlowski@linaro.org Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: yosemite4: correct Mellanox multi-host propertyKrzysztof Kozlowski1-2/+2
"mlx,multi-host" is using incorrect vendor prefix and is not documented. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240405064624.18997-2-krzysztof.kozlowski@linaro.org Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: greatlakes: correct Mellanox multi-host propertyKrzysztof Kozlowski1-1/+1
"mlx,multi-host" is using incorrect vendor prefix and is not documented. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240405064624.18997-1-krzysztof.kozlowski@linaro.org Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Modify I2C bus configurationRenze Nicolai1-0/+7
Enable I2C bus 8 which is exposed on the IPMB_1 connector on the X570D4U mainboard. Additionally adds a descriptive comment to I2C busses 1 and 5. Signed-off-by: Renze Nicolai <renze@rnplus.nl> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Disable unused ADC channels for Asrock X570D4U BMCRenze Nicolai1-16/+13
Additionally adds labels describing the ADC channels. Signed-off-by: Renze Nicolai <renze@rnplus.nl> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Modify GPIO table for Asrock X570D4U BMCRenze Nicolai1-58/+37
Restructure GPIO table to fit maximum line length. Fix mistakes found while working on OpenBMC userland configuration and based on probing the board. Schematic for this board is not available. Because of this the choice was made to use a descriptive method for naming the GPIOs. - Push-pull outputs start with output-* - Open-drain outputs start with control-* - LED outputs start with led-* - Inputs start with input-* - Button inputs start with button-* - Active low signals end with *-n Signed-off-by: Renze Nicolai <renze@rnplus.nl> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: yosemite4: set bus13 frequency to 100kDelphine CC Chiu1-1/+1
Since the ocp debug card only supports 100k, the bus is also set to 100k. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> [AJ: Fixed fuzz due to prior IPMB patch] Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: Aspeed: Bonnell: Fix NVMe LED labelsEddie James1-4/+4
The PCA chip for the NVMe LEDs is wired up backwards, so correct the device tree labels. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: yosemite4: Enable ipmb device for OCP debug cardDelphine CC Chiu1-0/+7
Add OCP debug card devicetree config Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: ahe50dc: Update lm25066 regulator nameZev Weiss1-1/+1
A recent change to the lm25066 driver changed the name of its regulator from vout0 to vout; device-tree users of lm25066's regulator functionality (of which ahe50dc is the only one) thus require a corresponding update. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Cc: Conor Dooley <conor+dt@kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Add vendor prefixes to lm25066 compat stringsZev Weiss2-3/+3
Due to the way i2c driver matching works (falling back to the driver's id_table if of_match_table fails) this didn't actually cause any misbehavior, but let's add the vendor prefixes so things actually work the way they were intended to. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: asrock: Use MAC address from FRU EEPROMZev Weiss2-0/+18
Like the more recently added ASRock BMC platforms, e3c246d4i and romed8hm3 also have the BMC's MAC address available in the baseboard FRU EEPROM, so let's add support for using it. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: system1: IBM System1 BMC boardAndrew Geissler2-0/+1624
Added a device tree for IBM system1 BMC board, which uses AST2600 SoC. Signed-off-by: Andrew Geissler <geissonator@yahoo.com> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com> Link: https://lore.kernel.org/r/20240125212154.4028640-3-ninad@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: FSI interrupt supportEddie James2-0/+6
Enable FSI interrupt controllers for AST2600 and P10BMC hub master. Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20240215220759.976998-27-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Modify GPIO line namePeter Yin1-9/+29
Add: "reset-cause-platrst", "cpu0-err-alert", "leakage-detect-alert", "presence-post-card", "ac-power-button", "P0_I3C_APML_ALERT_L", "irq-uv-detect-alert", "irq-hsc-alert", "cpu0-prochot-alert", "cpu0-thermtrip-alert", "reset-cause-pcie", "pvdd11-ocp-alert" Rename: "power-cpu-good" to "host0-ready", "host-ready-n" to "post-end-n Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-13-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add retimer devicePeter Yin1-0/+8
Add pt5161l device in i2c bus12 and bus21. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-12-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Revise node namePeter Yin1-3/+3
Revise max31790 and delta_brick node name. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-11-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add ltc4286 devicePeter Yin1-0/+7
Add ltc4286 device. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-10-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add NIC Fru devicePeter Yin1-0/+6
Add MB NIC Device Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-9-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Revise max31790 addressPeter Yin1-4/+4
Revise max31790 address from 0x30 to 0x5e Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-8-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add PDB temperaturePeter Yin1-1/+6
Add PDB temperature sensor. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-7-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add spi-gpioPeter Yin1-0/+21
Add spi-gpio for tpm device. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-6-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add cpu power good line namePeter Yin1-1/+1
Add a line name for cpu power good. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-5-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Remove VuartPeter Yin1-4/+0
Remove vuart to avoid port conflict with uart2 Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-4-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: mapping ttyS2 to UART4.Peter Yin1-2/+2
Change routing to match SOL(Serial Over LAN) settings. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-3-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Revise SGPIO line name.Peter Yin1-2/+2
The same name as reset-control-smb-e1s change to reset-control-smb-e1s-0 and reset-control-smb-e1s-0. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Link: https://lore.kernel.org/r/20240412091600.2534693-2-peteryin.openbmc@gmail.com Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: add sgpio line nameYang Chen1-0/+149
Add the SGPIO line name that the project's function can use by the meaningful name. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-12-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: add gpio line nameYang Chen1-0/+30
Add the GPIO line name that the project's function can use by the meaningful name. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-11-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Add led-fan-fault gpioYang Chen1-0/+17
Add led-fan-fault gpio pin on the PCA9555 on the i2c bus 0. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-10-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: add fan rpm controllerYang Chen1-0/+42
Add fan rpm controller max31790 on all bus of FCB. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-9-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: add bus labels and aliasesYang Chen1-6/+16
Add bus labels and aliases for the fan control board. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-8-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: correct the address of eepromYang Chen1-2/+2
Correct the address from 0x51 to 0x54 of eeprom on the i2c bus 1 Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-7-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Add temperature sensorYang Chen1-1/+6
Add one temperature sensor on i2c bus 1 Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-6-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Enable power monitor deviceYang Chen1-0/+22
Enable power monitor device ina230 and ltc2945 on the i2c bus 0 Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-5-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Change sgpio useYang Chen1-1/+1
Correct the sgpio use from sgpiom1 to sgpiom0 Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-4-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Modify mac3 settingYang Chen1-2/+5
Remove the unuse setting and fix the link to 100 M Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-3-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: minerva: Revise the name of DTSYang Chen2-2/+2
The project Minerva which is the platform used by Meta has two boards: the Chassis Management Module (Minerva) and the Motherboard (Harma), so change the DTS name to minerva here for CMM use. Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231212075200.983536-2-yangchen.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
2024-05-01ARM: dts: aspeed: Harma: Add Meta Harma (AST2600) BMCPeter Yin2-0/+586
Add linux device tree entry related to the Meta(Facebook) computer-node system use an AT2600 BMC. This node is named "Harma". Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20231211162656.2564267-3-peteryin.openbmc@gmail.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-11 05:53:25 +0300