summaryrefslogtreecommitdiff
path: root/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
AgeCommit message (Collapse)AuthorFilesLines
2024-02-19arm64: dts: amlogic: replace underscores in node namesKrzysztof Kozlowski1-4/+4
Underscores should not be used in node names (dtc with W=2 warns about them), so replace them with hyphens. Cc: Marc Gonzalez <mgonzalez@freebox.fr> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240213143217.336341-1-krzysztof.kozlowski@linaro.org Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
2021-11-15arm64: dts: meson-gxbb-wetek: use updated LED bindingsChristian Hewitt1-2/+5
Update the dts to use the newer style of LED bindings. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211012052522.30873-4-christianshewitt@gmail.com
2021-11-15arm64: dts: meson-gxbb-wetek: fix missing GPIO bindingChristian Hewitt1-0/+1
The absence of this binding appears to be harmless in Linux but it breaks Ethernet support in mainline u-boot. So add the binding (which is present in all other u-boot supported GXBB device-trees). Fixes: fb72c03e0e32 ("ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211012052522.30873-3-christianshewitt@gmail.com
2021-11-15arm64: dts: meson-gxbb-wetek: fix HDMI in early bootChristian Hewitt1-0/+2
Mark the VDDIO_AO18 regulator always-on and set hdmi-supply for the hdmi_tx node to ensure HDMI is powered in the early stages of boot. Fixes: fb72c03e0e32 ("ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20211012052522.30873-2-christianshewitt@gmail.com
2020-12-07arm64: dts: meson: fix PHY deassert timing requirementsStefan Agner1-1/+1
According to the datasheet (Rev. 1.9) the RTL8211F requires at least 72ms "for internal circuits settling time" before accessing the PHY registers. This fixes an issue seen on ODROID-C2 where the Ethernet link doesn't come up when using ip link set down/up: [ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down [ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36) [ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma [ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed [ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings") Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
2020-05-20arm64: dts: meson: add ethernet interrupt to wetek dtsiChristian Hewitt1-0/+4
Add Ethernet interrupt details to the WeTek Hub/Play2 dtsi to resolve an issue with Ethernet probing in mainline u-boot. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20200518025451.16401-1-christianshewitt@gmail.com
2020-04-29arm64: dts: meson: fix leds subnodes nameNeil Armstrong1-1/+1
Fix the leds subnode names to match (^led-[0-9a-f]$|led) It fixes: meson-g12b-a311d-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-g12b-s922x-khadas-vim3.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-g12b-odroid-n2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-nanopi-k2.dt.yaml: leds: 'stat' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-nexbox-a95x.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-odroidc2.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-vega-s95-pro.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-vega-s95-meta.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-vega-s95-telos.dt.yaml: leds: 'blue' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-wetek-hub.dt.yaml: leds: 'system' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxbb-wetek-play2.dt.yaml: leds: 'ethernet', 'system', 'wifi' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxl-s905x-libretech-cc.dt.yaml: leds: 'blue', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxl-s905d-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxm-rbox-pro.dt.yaml: leds: 'blue', 'red' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-gxm-s912-libretech-pc.dt.yaml: leds: 'blue', 'green' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-sm1-sei610.dt.yaml: leds: 'bluetooth' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' meson-sm1-khadas-vim3l.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20200326165958.19274-6-narmstrong@baylibre.com
2019-10-03arm64: dts: meson-gxbb-wetek: add keep-power-in-suspend property in SDIO nodeNeil Armstrong1-0/+3
The WiFi firmware requires that the power is kept enabled while in suspend mode. Add the keep-power-in-suspend property in the SDIO node to specify that the power must be kept when entering in a system wide suspend state. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-06-20arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindingsMartin Blumenstingl1-4/+4
The snps,reset-gpio bindings are deprecated in favour of the generic "Ethernet PHY reset" bindings. Replace snps,reset-gpio from the &ethmac node with reset-gpios in the ethernet-phy node. The old snps,reset-active-low property is now encoded directly as GPIO flag inside the reset-gpios property. snps,reset-delays-us is converted to reset-assert-us and reset-deassert-us. reset-assert-us is the second cell from snps,reset-delays-us while reset-deassert-us was the third cell. Instead of blindly copying the old values (which seems strange since they gave the PHY one second to come out of reset) over this also updates the delays based on the datasheets: - the Realtek RTL8211F PHY needs a 10ms assert delay (the datasheet mentions: "For a complete PHY reset, this pin must be asserted low for at least 10ms") and a 30ms deassert delay (the datasheet mentions: "Wait for a further 30ms (for internal circuits settling time) before accessing the PHY register". This applies to the following boards: GXBB NanoPi K2, GXBB Odroid-C2, GXBB Vega S95 variants, GXBB Wetek variants, GXL P230, GXM Khadas VIM2, GXM Nexbox A1, GXM Q200, GXM RBox Pro boards. - the ICPlus IP101GR PHY needs a 10ms assert delay (the datasheet mentions: "Trst | Reset period | 10ms") and a deassert delay of 10ms as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock output ready after reset released | 10ms"). This applies to the GXBB Nexbox A95X board. - the Micrel KSZ9031 seems to require a 100us delay but use the same (seemingly safe) values from RTL8211F due to lack of a board to verify this. This applies to the GXBB P200 board. The GXBB P201 board is left out from this conversion because it doesn't have a dedicated PHY node (because it's not clear which PHY is used on that board). Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-06-12arm64: dts: meson-gxbb-wetek: enable bluetoothChristian Hewitt1-0/+13
This enables Bluetooth support for the following models: AP6335 in the WeTek Hub rev1 - BCM4335C0.hcd AP6255 in the WeTek Hub rev2 - BCM4345C0.hcd AP6330 in the WeTek Play 2 - BCM4330B1.hcd Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-06-12arm64: dts: meson-gxbb-wetek: enable SARADCChristian Hewitt1-0/+12
Enable SARADC on Wetek Boards. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-05-21arm64: dts: meson: fix mmc v2 chips max frequenciesJerome Brunet1-2/+2
According the datasheets, emmc v2 chips (gxbb and gxl) don't support more that 100Mhz in UHS-1 SD modes and HS in SDIO. Align the max-frequency to 100MHz for UHS-1 and 50MHz for HS Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-01-14arm64: dts: meson: Fix mmc cd-gpios polarityLoys Ollivier1-2/+1
Commit 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree") changed the behavior of "cd-inverted" to follow the device tree bindings specification: According to SDHCI standard, CD lines are specified as "active low". Using the "cd-inverted" property means that the CD line is "active high". Fix the SD card description for meson by setting the cd-gpios as "active low", according to the boards specifications, and dropping the "cd-inverted" property. Fixes: 89a5e15bcba8 ("gpio/mmc/of: Respect polarity in the device tree") Signed-off-by: Loys Ollivier <lollivier@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-12-08arm64: dts: meson: Fix IRQ trigger type for macirqCarlo Caione1-1/+0
A long running stress test on a custom board shipping an AXG SoCs and a Realtek RTL8211F PHY revealed that after a few hours the connection speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time the 'macirq' (eth0) IRQ would stop being triggered at all and as consequence the GMAC IRQs never ACKed. After a painful investigation the problem seemed to be due to a wrong defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of EDGE_RISING. The change in the macirq IRQ type also solved another long standing issue affecting this SoC/PHY where EEE was causing the network connection to die after stressing it with iperf3 (even though much sooner). It's now possible to remove the 'eee-broken-1000t' quirk as well. Fixes: feb3cbea0946 ("ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage") Fixes: 6d28d577510f ("ARM64: dts: meson-axg: fix ethernet stability issue") Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Carlo Caione <ccaione@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-08ARM64: dts: meson-gxbb-wetek: add a wetek specific dtsi to cleanup hub and play2Neil Armstrong1-0/+256
This patch adds a specific wetek dtsi to handle the specific Hub and Play2 boards by no more depending on the p20x dtsi. This simplifies the hub and play2 dts and will avoid breaking these boards when adding p200 and p201 specific changes. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-10-19 05:00:02 +0300