Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is a small set of tty and serial driver updates for 6.11-rc1. Not
much happened this cycle, unlike the previous kernel release which had
lots of "excitement" in this part of the kernel. Included in here are
the following changes:
- dt binding updates for new platforms
- 8250 driver updates
- various small serial driver fixes and updates
- printk/console naming and matching attempt #2 (was reverted for
6.10-final, should be good to go this time around, acked by the
relevant maintainers).
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (22 commits)
Documentation: kernel-parameters: Add DEVNAME:0.0 format for serial ports
serial: core: Add serial_base_match_and_update_preferred_console()
printk: Add match_devname_and_update_preferred_console()
serial: sc16is7xx: hardware reset chip if reset-gpios is defined in DT
dt-bindings: serial: sc16is7xx: add reset-gpios
dt-bindings: serial: vt8500-uart: convert to json-schema
serial: 8250_platform: Explicitly show we initialise ISA ports only once
tty: add missing MODULE_DESCRIPTION() macros
dt-bindings: serial: mediatek,uart: add MT7988
serial: sh-sci: Add support for RZ/V2H(P) SoC
dt-bindings: serial: Add documentation for Renesas RZ/V2H(P) (R9A09G057) SCIF support
dt-bindings: serial: renesas,scif: Make 'interrupt-names' property as required
dt-bindings: serial: renesas,scif: Validate 'interrupts' and 'interrupt-names'
dt-bindings: serial: renesas,scif: Move ref for serial.yaml at the end
riscv: dts: starfive: jh7110: Add the core reset and jh7110 compatible for uarts
serial: 8250_dw: Use reset array API to get resets
dt-bindings: serial: snps-dw-apb-uart: Add one more reset signal for StarFive JH7110 SoC
serial: 8250: Extract platform driver
serial: 8250: Extract RSA bits
serial: imx: stop casting struct uart_port to struct imx_port
...
|
|
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
|
|
into soc/dt
RISC-V Devicetrees for v6.11
Sopgho:
Add clock support for SG2042.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
* tag 'riscv-sophgo-dt-for-v6.11' of https://github.com/sophgo/linux:
riscv: dts: add clock generator for Sophgo SG2042 SoC
Link: https://lore.kernel.org/r/PN1P287MB281861EA2B1706B430D2FA3EFEDB2@PN1P287MB2818.INDP287.PROD.OUTLOOK.COM
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add clock generator node to device tree for SG2042, and enable clock for
uart.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetrees for v6.11
T-Head:
Last change from me before this starts going via Drew's tree is the
addition of the SBI PMU events node for the th1520.
StarFive:
A dts for the Pin64 Star64, another board with a jh7110 SoC. This board
is almost identical to the existing Milk-v Mars and VisionFive 2 boards
that are already support - just with a different PHY configuration and
only one of the two PCIe ports exposed. Additionally, the Mars and
VisionFive 2 get their PCie configuration added.
Microchip:
A dts for the BeagleV Fire. PCIe is disabled on it for now, as some
binding and driver changes are required.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: add PCIe dts configuration for JH7110
riscv: dts: microchip: add an initial devicetree for the BeagleV Fire
dt-bindings: riscv: microchip: document beaglev-fire
riscv: dts: starfive: Update flash partition layout
riscv: dts: thead: th1520: Add PMU event node
riscv: dts: starfive: add Star64 board devicetree
dt-bindings: riscv: starfive: add Star64 board compatible
dt-bindings: riscv: Add T-HEAD C908 compatible
Link: https://lore.kernel.org/r/20240707-nuttiness-lustfully-4aaf03c991b2@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into soc/dt
Allwinner SoC device tree changes for 6.11
This includes a commit shared with the clk tree. This commit adds clock
and reset indices to the device tree binding, and thus is needed for
both the device tree and driver changes.
ARM64 device tree and binding-only changes
- Add LRADC (low resolution ADC for resistor network based keys) for H616 SoC
- Add cache information for A64, H6, and H616 SoCs
- Correct model names and descriptions for Pine64 boards
- Add GPADC (general purpose ADC) for H616 SoC
- Add ADC joysticks based on GPADC for anbernic-rg35xx-h board
- Add additional CPU OPPs for the H700 on top of existing H616 ones
- Enable DVFS for rg35xx boards
- Add IOMMU for H616 SoC
RISC-V device tree changes
- Add system LDOs to D1s/T113 SoC
- Add ClockworkPi and DevTerm device trees
* tag 'sunxi-dt-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
riscv: dts: allwinner: Add ClockworkPi and DevTerm devicetrees
riscv: dts: allwinner: d1s-t113: Add system LDOs
arm64: dts: allwinner: h616: add IOMMU node
arm64: dts: allwinner: rg35xx: Enable DVFS CPU frequency scaling
arm64: dts: allwinner: h616: add additional CPU OPPs for the H700
arm64: dts: allwinner: anbernic-rg35xx-h: Add ADC joysticks
arm64: dts: allwinner: h616: Add GPADC device node
dt-bindings: clock: sun50i-h616-ccu: Add GPADC clocks
ARM: dts: sunxi: remove duplicated entries in makefile
arm64: dts: allwinner: Add cache information to the SoC dtsi for H616
arm64: dts: allwinner: Add cache information to the SoC dtsi for A64
arm64: dts: allwinner: Correct the model names for Pine64 boards
dt-bindings: arm: sunxi: Correct the descriptions for Pine64 boards
arm64: dts: allwinner: Add cache information to the SoC dtsi for H6
ARM: dts: sun50i: Add LRADC node
dt-bindings: input: sun4i-lradc-keys: Add H616 compatible
Link: https://lore.kernel.org/r/ZoQa8r1N8yi7FlPV@wens.tw
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add PCIe dts configuraion for JH7110 SoC platform. The Star64 only has
one exposed PCIe port, so only the Mars and VisionFive 2 get two
enabled.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
[conor: squash in star64's single exposed port]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This resolves the merge issues in the 8250 code due to some reverts in
6.10-rc6 in the console changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clockwork Tech manufactures several SoMs for their RasPi CM3-compatible
"ClockworkPi" mainboard. Their R-01 SoM features the Allwinner D1 SoC.
The R-01 contains only the CPU, DRAM, and always-on voltage regulation;
it does not merit a separate devicetree.
The ClockworkPi mainboard features analog audio, a MIPI-DSI panel, USB
host and peripheral ports, an Ampak AP6256 WiFi/Bluetooth module, and an
X-Powers AXP228 PMIC for managing a Li-ion battery.
The DevTerm is a complete system which extends the ClockworkPi mainboard
with a MIPI-DSI panel and a pair of expansion boards. These expansion
boards provide a fan, a USB keyboard, speakers, and a thermal printer.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20240622150731.1105901-4-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Now that the bindings for the system LDOs have been merged, the nodes
for the system LDOs can be added. These are used on the ClockworkPi.
This was originally part of Samuel's D1 device tree series [1], but was
dropped in v5 as the regulator bindings weren't merged at the time.
[1] https://lore.kernel.org/linux-sunxi/20221231233851.24923-1-samuel@sholland.org/
Link: https://lore.kernel.org/r/20240622150731.1105901-3-wens@kernel.org
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.10-rc5+
T-Head:
Jisheng hasn't got enough time to look after the platform, so Drew
Fustini is going to take over.
StarFive:
A fix for a regulator voltage range that prevented using low performance
SD cards.
Canaan:
Cleanup for some "over eager" aliases for serial ports that did not
exist on some boards and I/O devices disabled on boards where they were
not actually in use.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the core reset for uarts, which is necessary for uarts to work.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20240604084729.57239-4-hal.feng@starfivetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add an initial devicetree for the BeagleV Fire. This devicetree differs
from that in the BeagleBoard BSP as it has a different memory
configuration, however it will boot on the same FPGA images. PCI is
disabled for now, as the Linux PCI driver (and the binding) assume
which root port instance is in use. This will need to be fixed before
PCI can be enabled.
Link: https://www.beagleboard.org/boards/beaglev-fire
Co-developed-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Currently, for JH7110 boards with EMMC slot, vqmmc voltage for EMMC is
fixed to 1.8V, while the spec needs it to be 3.3V on low speed mode and
should support switching to 1.8V when using higher speed mode. Since
there are no other peripherals using the same voltage source of EMMC's
vqmmc(ALDO4) on every board currently supported by mainline kernel,
regulator-max-microvolt of ALDO4 should be set to 3.3V.
Cc: stable@vger.kernel.org
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 7dafcfa79cc9 ("riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Up to now, the describe flash partition layout has some gaps.
Use the whole flash chip by getting rid of the gaps.
Suggested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
T-HEAD th1520 uses standard C910 chip and its pmu is already supported
by OpenSBI.
Add the pmu event description for T-HEAD th1520 SoC.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Link: https://www.xrvm.com/product/xuantie/4240217381324001280?spm=xrvm.27140568.0.0.7f979b29nzIa1m
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The Pine64 Star64 is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 1x USB 3.0 host port
- 3x USB 2.0 host port
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 2x 1Gbps Ethernet port
- 1x HDMI port
- 1x 4-lane DSI
- 1x 2-lane CSI
- 1x PCIe 2.0 x1 lane
Signed-off-by: Henry Bell <dmoo_dv@protonmail.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Milkv Duo does not have a write-protect pin, so disable write protect
to prevent SDcards misdetected as read-only.
Fixes: 89a7056ed4f7 ("riscv: dts: sophgo: add sdcard support for milkv duo")
Signed-off-by: Haylen Chu <heylenay@outlook.com>
Link: https://lore.kernel.org/r/SEYPR01MB4221943C7B101DD2318DA0D3D7CE2@SEYPR01MB4221.apcprd01.prod.exchangelabs.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
It is considered good practice to disable on-SoC devices providing
external I/O in the SoC-specific .dtsi, and enable them explicitly in
the board-specific DTS files when actually wired-up and used.
Hence:
- Set the status of I/O devices in k210.dtsi to "disabled",
- Override the status of used I/O devices in board-specific DTS files
to "okay",
- Drop unneeded status overrides in board DTS-specific files for the
always-enabled pin controller.
On e.g. MAiXBiT, this gets rid of an error message when probing the
unused slave-only spi2 controller:
dw_spi_mmio 50240000.spi: error -22: problem registering spi host
dw_spi_mmio 50240000.spi: probe with driver dw_spi_mmio failed with error -22
which is seen since commit 98d75b9ef282f6b9 ("spi: dw: Drop default
number of CS setting").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The SoC-specific k210.dtsi declares aliases for all four serial ports.
However, none of the board-specific DTS files configure pin control for
any but the first serial port, so the last three ports are not usable.
Move the aliases node from the SoC-specific k210.dtsi to the
board-specific DTS files, as these are really board-specific, and retain
the sole port that is usable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more SoC devicetree updates from Arnd Bergmann:
"This is a follow-up to an earlier pull request for device tree
changes, as three platform maintainers sent their contents too late to
be included in the main set, but had not caused any further problems
since then:
- The Amlogic platform now containts support for two new SoC types,
the A4 and A5 chips for audio applications. Both come with a
reference board, and one more dts file gets addded for the
combination of the MNT Reform Laptop with the BPI-CM4 CPU module
- The ASpeed platform adds support for six addititional server
platforms that use ast2500 or ast2600 as their BMC, while another
one gets removed
- The RISC-V platforms from Microchip, Starfive and and T-HEAD get
additional features for existing hardware, plus the addition of the
Milk-V Mars based on the StarFive VisionFive v2 board"
* tag 'soc-dt-late-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (76 commits)
riscv: dts: microchip: add pac1934 power-monitor to icicle
riscv: dts: thead: Fix node ordering in TH1520 device tree
ARM: dts: aspeed: Add ASRock E3C256D4I BMC
dt-bindings: arm: aspeed: document ASRock E3C256D4I
dt-bindings: trivial-devices: add isil,isl69269
ARM: dts: aspeed: x4tf: Add dts for asus x4tf project
dt-bindings: arm: aspeed: add ASUS X4TF board
ARM: dts: aspeed: Remove Facebook Cloudripper dts
ARM: dts: aspeed: drop unused ref_voltage ADC property
ARM: dts: aspeed: harma: correct Mellanox multi-host property
ARM: dts: aspeed: yosemitev2: correct Mellanox multi-host property
ARM: dts: aspeed: yosemite4: correct Mellanox multi-host property
ARM: dts: aspeed: greatlakes: correct Mellanox multi-host property
ARM: dts: aspeed: Modify I2C bus configuration
ARM: dts: aspeed: Disable unused ADC channels for Asrock X570D4U BMC
ARM: dts: aspeed: Modify GPIO table for Asrock X570D4U BMC
ARM: dts: aspeed: yosemite4: set bus13 frequency to 100k
ARM: dts: Aspeed: Bonnell: Fix NVMe LED labels
ARM: dts: aspeed: yosemite4: Enable ipmb device for OCP debug card
ARM: dts: aspeed: ahe50dc: Update lm25066 regulator name
...
|
|
The binding for this landed in v6.9, add the description. In the
off-chance that there were people carrying local patches for this based
on the driver shipped on the Microchip website (or vendor kernel) both
the binding and sysfs filenames changed during upstreaming.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The Milkv Mars is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI
I fixed up some nits Emil pointed out. This merges fixes into for-next
to avoid messing around with some nodes that were removed as fixes this
cycle.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
According to the device tree coding style, nodes shall be ordered by
unit address in ascending order.
Signed-off-by: Thomas Bonnefille <thomas.bonnefille@bootlin.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
into soc/dt
RISC-V Devicetrees for v6.10
Sophgo:
Added sdhci support for cv18xx/duo.
Added clock support for cv18xx.
Added clock for uart/sdhci.
Added spi support for cv18xx.
Added i2c support for cv18xx.
Added reserved memory node for cv1800b/duo.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
* tag 'riscv-sophgo-dt-for-v6.10' of https://github.com/sophgo/linux:
riscv: dts: sophgo: add reserved memory node for CV1800B
riscv: dts: sophgo: use real clock for sdhci
riscv: dts: sophgo: cv18xx: Add i2c devices
riscv: dts: sophgo: cv18xx: Add spi devices
riscv: dts: sophgo: add uart clock for Sophgo CV1800 series SoC
riscv: dts: sophgo: add clock generator for Sophgo CV1800 series SoC
riscv: dts: sophgo: add sdcard support for milkv duo
Link: https://lore.kernel.org/r/MA0P287MB2822CA2DE757787D6EA3B1F8FE192@MA0P287MB2822.INDP287.PROD.OUTLOOK.COM
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The Milkv Mars is a development board based on the Starfive JH7110 SoC.
The board features:
- JH7110 SoC
- 1/2/4/8 GiB LPDDR4 DRAM
- AXP15060 PMIC
- 40 pin GPIO header
- 3x USB 3.0 host port
- 1x USB 2.0 host port
- 1x M.2 E-Key
- 1x eMMC slot
- 1x MicroSD slot
- 1x QSPI Flash
- 1x 1Gbps Ethernet port
- 1x HDMI port
- 1x 2-lane DSI and 1x 4-lane DSI
- 1x 2-lane CSI
Add the devicetree file describing the currently supported features,
namely PMIC, UART, I2C, GPIO, SD card, QSPI Flash, eMMC and Ethernet.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This is to prepare for Milkv Mars board dts support in the following
patch. Let's factored out common part into .dtsi.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
No physical write-protect line is present, so setting "disable-wp".
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Per VisionFive 2 1.2B, and 1.3A boards' SCH, GPIO 41 is used as
card detect. So add "cd-gpios" property for this.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
As pointed out by Krzysztof "Board should not bring new CPU nodes.
Override by label instead."
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Use "audio-codec" as the codec dt node name, and "sound" as the simple
audio card dt name.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add the 'cpus' label so that we can reference it in board dts files.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The original dts of CV1800B has a weird memory length as it
contains reserved memory for coprocessor. Make this area a
separate node so it can get the real memory length.
Link: https://lore.kernel.org/r/IA1PR20MB49531F274753B04A5547DB59BB052@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
from ETH0/1 nodes
Now that we have enabled IRQC support for RZ/Five SoC switch to interrupt
mode for ethernet0/1 PHYs instead of polling mode.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240403203503.634465-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the IRQC node to RZ/Five (R9A07G043F) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240403203503.634465-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
As the clk patch is merged, Use real clocks for sdhci0.
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://lore.kernel.org/r/IA1PR20MB4953CA5D46EA8913B130D502BB052@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
This partially reverts
commit 92cfc35838b2 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
This added device tree nodes for I2S hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the TDM node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: 92cfc35838b2 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This partially reverts
commit e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
This added device tree nodes for TDM hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the I2S node which also attempts to grab GPIO 44:
starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s
Fixes: e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Add i2c devices for the CV180x, CV181x and SG200x soc.
Link: https://lore.kernel.org/r/IA1PR20MB49531AA2DBD4832B7926D4A8BB442@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
Add spi devices for the CV180x, CV181x and SG200x soc.
Link: https://lore.kernel.org/r/IA1PR20MB49532705DE532BCF81CCEFD0BB442@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
Add missing clocks of uart node for CV1800B and CV1812H.
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://lore.kernel.org/r/IA1PR20MB4953198222C3ABC2A2B6DE21BB262@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
Add clock generator node for CV1800B and CV1812H.
Until now, It uses DT override to minimize duplication. This may
change in the future. See the last link for the discussion on
maintaining DT of CV1800 series.
Link: https://github.com/milkv-duo/duo-files/blob/6f4e9b8ecb459e017cca1a8df248a19ca70837a3/duo/datasheet/CV1800B-CV1801B-Preliminary-Datasheet-full-en.pdf
Link: https://lore.kernel.org/all/IA1PR20MB495373158F3B690EF3BF2901BB8BA@IA1PR20MB4953.namprd20.prod.outlook.com/
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Link: https://lore.kernel.org/r/IA1PR20MB4953ED6A4B57773865F49D6DBB262@IA1PR20MB4953.namprd20.prod.outlook.com
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
Add sdhci dt node in SoC dtsi and enable it in milkv duo dts.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Inochi Amaoto <inochiama@outlook.com>
Link: https://lore.kernel.org/r/20240217144826.3944-1-jszhang@kernel.org
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
|
|
Interrupt line number of the AXP15060 PMIC is not a necessary part of
its device tree. Originally the binding required one, so the dts patch
added an invalid interrupt that the driver ignored (0) as the interrupt
line of the PMIC is not actually connected on this platform. This went
unnoticed during review as it would have been a valid interrupt for a
GPIO controller, but it is not for the PLIC. The PLIC, on this platform
at least, silently ignores the enablement of interrupt 0. Bo Gan is
running a modified version of OpenSBI that faults if writes are done to
reserved fields, so their kernel runs into problems.
Delete the invalid interrupt from the device tree.
Cc: stable@vger.kernel.org
Reported-by: Bo Gan <ganboing@gmail.com>
Link: https://lore.kernel.org/all/c8b6e960-2459-130f-e4e4-7c9c2ebaa6d3@gmail.com/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Fixes: 2378341504de ("riscv: dts: starfive: Enable axp15060 pmic for cpufreq")
[conor: rewrite the commit message to add more detail]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for various vector-accelerated crypto routines
- Hibernation is now enabled for portable kernel builds
- mmap_rnd_bits_max is larger on systems with larger VAs
- Support for fast GUP
- Support for membarrier-based instruction cache synchronization
- Support for the Andes hart-level interrupt controller and PMU
- Some cleanups around unaligned access speed probing and Kconfig
settings
- Support for ACPI LPI and CPPC
- Various cleanus related to barriers
- A handful of fixes
* tag 'riscv-for-linus-6.9-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (66 commits)
riscv: Fix syscall wrapper for >word-size arguments
crypto: riscv - add vector crypto accelerated AES-CBC-CTS
crypto: riscv - parallelize AES-CBC decryption
riscv: Only flush the mm icache when setting an exec pte
riscv: Use kcalloc() instead of kzalloc()
riscv/barrier: Add missing space after ','
riscv/barrier: Consolidate fence definitions
riscv/barrier: Define RISCV_FULL_BARRIER
riscv/barrier: Define __{mb,rmb,wmb}
RISC-V: defconfig: Enable CONFIG_ACPI_CPPC_CPUFREQ
cpufreq: Move CPPC configs to common Kconfig and add RISC-V
ACPI: RISC-V: Add CPPC driver
ACPI: Enable ACPI_PROCESSOR for RISC-V
ACPI: RISC-V: Add LPI driver
cpuidle: RISC-V: Move few functions to arch/riscv
riscv: Introduce set_compat_task() in asm/compat.h
riscv: Introduce is_compat_thread() into compat.h
riscv: add compile-time test into is_compat_task()
riscv: Replace direct thread flag check with is_compat_task()
riscv: Improve arch_get_mmap_end() macro
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"These are changes that for some reason ended up not making it into the
first four branches but that should still make it into 6.9:
- A rework of the omap clock support that touches both drivers and
device tree files
- The reset controller branch changes that had a dependency on late
bugfixes. Merging them here avoids a backmerge of 6.8-rc5 into the
drivers branch
- The RISC-V/starfive, RISC-V/microchip and ARM/Broadcom devicetree
changes that got delayed and needed some extra time in linux-next
for wider testing"
* tag 'soc-late-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
soc: fsl: dpio: fix kcalloc() argument order
bus: ts-nbus: Improve error reporting
bus: ts-nbus: Convert to atomic pwm API
riscv: dts: starfive: jh7110: Add camera subsystem nodes
ARM: bcm: stop selecing CONFIG_TICK_ONESHOT
ARM: dts: omap3: Update clksel clocks to use reg instead of ti,bit-shift
ARM: dts: am3: Update clksel clocks to use reg instead of ti,bit-shift
clk: ti: Improve clksel clock bit parsing for reg property
clk: ti: Handle possible address in the node name
dt-bindings: pwm: opencores: Add compatible for StarFive JH8100
dt-bindings: riscv: cpus: reg matches hart ID
reset: Instantiate reset GPIO controller for shared reset-gpios
reset: gpio: Add GPIO-based reset controller
cpufreq: do not open-code of_phandle_args_equal()
of: Add of_phandle_args_equal() helper
reset: simple: add support for Sophgo SG2042
dt-bindings: reset: sophgo: support SG2042
riscv: dts: microchip: add specific compatible for mpfs pdma
riscv: dts: microchip: add missing CAN bus clocks
ARM: brcmstb: Add debug UART entry for 74165
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"No core changes this time around.
New drivers:
- New driver for Renesas R8A779H0 also known as R-Car V4M.
- New driver for the Awinic AW9523/B I2C GPIO expander. I found this
living out-of-tree in OpenWrt as an upstream attempt had stalled on
the finishing line, so I picked it up and finished the job.
Improvements:
- The Nomadik pin control driver was for years re-used out of tree
for the ST STA chips, and now the IP was re-used in a MIPS
automotive SoC called MobilEyeq5, so it has been split in pin
control and GPIO drivers so the latter can be reused by MobilEyeq5.
(Along with a long list of cleanups)
- A lot of overall cleanup and tidying up"
* tag 'pinctrl-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (87 commits)
drivers/gpio/nomadik: move dummy nmk_gpio_dbg_show_one() to header
gpio: nomadik: remove BUG_ON() in nmk_gpio_populate_chip()
dt-bindings: pinctrl: qcom: update compatible name for match with driver
pinctrl: aw9523: Make the driver tristate
pinctrl: nomadik: fix dereference of error pointer
gpio: nomadik: Back out some managed resources
pinctrl: aw9523: Add proper terminator
pinctrl: core: comment that pinctrl_add_gpio_range() is deprecated
pinctrl: pinmux: Suppress error message for -EPROBE_DEFER
pinctrl: Add driver for Awinic AW9523/B I2C GPIO Expander
dt-bindings: pinctrl: Add bindings for Awinic AW9523/AW9523B
gpio: nomadik: Finish conversion to use firmware node APIs
gpio: nomadik: fix Kconfig dependencies inbetween pinctrl & GPIO
pinctrl: da9062: Add OF table
dt-bindings: pinctrl: at91: add sam9x7
pinctrl: ocelot: remove redundant assignment to variable ret
gpio: nomadik: grab optional reset control and deassert it at probe
gpio: nomadik: support mobileye,eyeq5-gpio
gpio: nomadik: handle variadic GPIO count
gpio: nomadik: support shared GPIO IRQs
...
|
|
xandespmu stands for Andes Performance Monitor Unit extension.
Based on the added Andes PMU ISA string, the SBI PMU driver
will make use of the non-standard irq source.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240222083946.3977135-10-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The Andes hart-level interrupt controller (Andes INTC) allows AX45MP
cores to handle custom local interrupts, such as the performance
counter overflow interrupt.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240222083946.3977135-6-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt
RISC-V Devicetree fixes for v6.8-final
Starfive:
The previous cleanup broke boot on the jh7100 as the driver depended on
the fallback clock name created based on the node-name when
clock-output-names is not present. Add clock-output-names to restore
working order.
Generic:
BUILTIN_DTB has been broken for ages on any platform other than the
nommu Canaan k210 SoC as the first dtb built (in alphanumerical order),
would get built into the image. This didn't get fixed for ages because
nobody actually cared about running it other than the k210 enough to
fix it. The folks doing Sophgo SG2042 development have come along and
fixed it, as they want to use builtin dtbs. linux-boot on that platform
reuses the dtb it was provided by OpenSBI when booting linux proper,
which is unfortunately not possible to boot a mainline kernel with.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.8-final' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: Move BUILTIN_DTB_SOURCE to common Kconfig
riscv: dts: starfive: jh7100: fix root clock names
Link: https://lore.kernel.org/r/20240306-waltz-facial-9e4e1b792053@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|