| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
The work can submit URBs and the URBs can schedule the work.
This cycle needs to be broken, when a device is to be stopped.
Use a flag to do so.
This is a design issue as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Link: https://patch.msgid.link/20240919123525.688065-1-oneukum@suse.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/phy/phy_device.c
2560db6ede1a ("net: phy: Fix missing of_node_put() for leds")
1dce520abd46 ("net: phy: Use for_each_available_child_of_node_scoped()")
https://lore.kernel.org/20240904115823.74333648@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/xilinx/xilinx_axienet.h
drivers/net/ethernet/xilinx/xilinx_axienet_main.c
858430db28a5 ("net: xilinx: axienet: Fix race in axienet_stop")
76abb5d675c4 ("net: xilinx: axienet: Add statistics support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
generic_ocp_write() asks the parameter "size" must be 4 bytes align.
Therefore, write the bp would fail, if the mac->bp_num is odd. Align the
size to 4 for fixing it. The way may write an extra bp, but the
rtl8152_is_fw_mac_ok() makes sure the value must be 0 for the bp whose
index is more than mac->bp_num. That is, there is no influence for the
firmware.
Besides, I check the return value of generic_ocp_write() to make sure
everything is correct.
Fixes: e5c266a61186 ("r8152: set bp in bulk")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20240903063333.4502-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver generates a random MAC once on load
and uses it over and over, including on two devices
needing a random MAC at the same time.
Jakub suggested revamping the driver to the modern
API for setting a random MAC rather than fixing
the old stuff.
The bug is as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://patch.msgid.link/20240829175201.670718-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
c25504a0ba36 ("dt-bindings: net: fsl,qoriq-mc-dpmac: add missed property phys")
be034ee6c33d ("dt-bindings: net: fsl,qoriq-mc-dpmac: using unevaluatedProperties")
https://lore.kernel.org/20240815110934.56ae623a@canb.auug.org.au
drivers/net/dsa/vitesse-vsc73xx-core.c
5b9eebc2c7a5 ("net: dsa: vsc73xx: pass value in phy_write operation")
fa63c6434b6f ("net: dsa: vsc73xx: check busy flag in MDIO operations")
2524d6c28bdc ("net: dsa: vsc73xx: use defined values in phy operations")
https://lore.kernel.org/20240813104039.429b9fe6@canb.auug.org.au
Resolve by using FIELD_PREP(), Stephen's resolution is simpler.
Adjacent changes:
net/vmw_vsock/af_vsock.c
69139d2919dd ("vsock: fix recursive ->recvmsg calls")
744500d81f81 ("vsock: add support for SIOCOUTQ ioctl")
Link: https://patch.msgid.link/20240815141149.33862-1-pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The usbnet_link_change function is not called, if the link has not changed.
...
[16913.807393][ 3] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 12 may have been dropped
[16913.822266][ 2] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 12 may have been dropped
[16913.826296][ 2] cdc_ether 1-2:2.0 enx00e0995fd1ac: kevent 11 may have been dropped
...
kevent 11 is scheduled too frequently and may affect other event schedules.
Signed-off-by: zhangxiangqian <zhangxiangqian@kylinos.cn>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/1723109985-11996-1-git-send-email-zhangxiangqian@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Apart from the standard "configurations", "interfaces" and "alternate
interface settings" in USB, iOS devices also have a notion of
"modes". In different modes, the device exposes a different set of
available configurations.
Depending on the iOS version, and depending on the current mode, the
length and contents of the carrier state control message differs:
* 1 byte (seen on iOS 4.2.1, 8.4):
* 03: carrier off (mode 0)
* 04: carrier on (mode 0)
* 3 bytes (seen on iOS 10.3.4, 15.7.6):
* 03 03 03: carrier off (mode 0)
* 04 04 03: carrier on (mode 0)
* 4 bytes (seen on iOS 16.5, 17.6):
* 03 03 03 00: carrier off (mode 0)
* 04 03 03 00: carrier off (mode 1)
* 06 03 03 00: carrier off (mode 4)
* 04 04 03 04: carrier on (mode 0 and 1)
* 06 04 03 04: carrier on (mode 4)
Before this change, the driver always used the first byte of the
response to determine carrier state.
From this larger sample, the first byte seems to indicate the number of
available USB configurations in the current mode (with the exception of
the default mode 0), and in some cases (namely mode 1 and 4) does not
correlate with the carrier state.
Previous logic erroneously counted `04 03 03 00` as "carrier on" and
`06 04 03 04` as "carrier off" on iOS versions that support mode 1 and
mode 4 respectively.
Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for
the ipheth driver.
Check the second byte of the control message where possible, and fall
back to checking the first byte on older iOS versions.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX callbacks can fail for multiple reasons:
* Payload too short
* Payload formatted incorrecly (e.g. bad NCM framing)
* Lack of memory
None of these should cause the driver to seize up.
Make such failures non-critical and continue processing further
incoming URBs.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On iPhone 15 Pro Max one can observe periodic URBs with no payload
on the "bulk in" (RX) endpoint. These don't seem to do anything
meaningful. Reproduced on iOS 17.5.1 and 17.6.
This behaviour isn't observed on iPhone 11 on the same iOS version. The
nature of these zero-length URBs is so far unknown.
Drop RX URBs with no payload.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy()
and ipheth_rcvbulk_callback_ncm(), depending on the current mode.
The check in ipheth_rcvbulk_callback() was thus mostly a duplicate.
The only place in ipheth_rcvbulk_callback() where we care about the URB
length is for the initial control frame. These frames are always 4 bytes
long. This has been checked as far back as iOS 4.2.1 on iPhone 3G.
Remove the extraneous URB length check. For control frames, check for
the specific 4-byte length instead.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipheth_sndbulk_callback() can submit carrier_work
as a part of its error handling. That means that
the driver must make sure that the work is cancelled
after it has made sure that no more URB can terminate
with an error condition.
Hence the order of actions in ipheth_close() needs
to be inverted.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for MeiG Smart SRM825L which is based on Qualcomm 315 chip.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=2dee ProdID=4d22 Rev= 4.14
S: Manufacturer=MEIG
S: Product=LTE-A Module
S: SerialNumber=6f345e48
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: ZHANG Yuntian <yt@radxa.com>
Link: https://patch.msgid.link/D1EB81385E405DFE+20240803074656.567061-1-yt@radxa.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Free the unused skb when not ip packets arrive.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It could lead to error happen because the variable res is not updated if
the call to sr_share_read_word returns an error. In this particular case
error code was returned and res stayed uninitialized. Same issue also
applies to sr_read_reg.
This can be avoided by checking the return value of sr_share_read_word
and sr_read_reg, and propagating the error if the read operation failed.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a050 ("ionic: fix kernel panic due to multi-buffer handling")
d9c04209990b ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit FN912 compositions:
0x3000: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=07 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=3000 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN912
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x3001: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=07 Cnt=01 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=3001 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN912
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://patch.msgid.link/20240625102236.69539-1-dnlplm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid spurious link status logs that may ultimately be wrong; for example,
if the link is set to down with the cable plugged, then the cable is
unplugged and after this the link is set to up, the last new log that is
appearing is incorrectly telling that the link is up.
In order to avoid errors, show link status logs after link_reset
processing, and in order to avoid spurious as much as possible, only show
the link loss when some link status change is detected.
cc: stable@vger.kernel.org
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
1e7962114c10 ("bnxt_en: Restore PTP tx_avail count in case of skb_pad() error")
165f87691a89 ("bnxt_en: add timestamping statistics support")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This functions retrieves values by passing a pointer. As the function
that retrieves them can fail before touching the pointers, the variables
must be initialized.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+5186630949e3c55f0799@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240619132816.11526-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is
set to down/up") to not reset from usbnet_open after the reset from
usbnet_probe at initialization stage to speed up this, some issues have
been reported.
It seems to happen that if the initialization is slower, and some time
passes between the probe operation and the open operation, the second reset
from open is necessary too to have the device working. The reason is that
if there is no activity with the phy, this is "disconnected".
In order to improve this, the solution is to detect when the phy is
"disconnected", and we can use the phy status register for this. So we will
only reset the device from reset operation in this situation, that is, only
if necessary.
The same bahavior is happening when the device is stopped (link set to
down) and later is restarted (link set to up), so if the phy keeps working
we only need to enable the mac again, but if enough time passes between the
device stop and restart, reset is necessary, and we can detect the
situation checking the phy status register too.
cc: stable@vger.kernel.org # 6.6+
Fixes: ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is set to down/up")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Reported-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Reported-by: Arne Fitzenreiter <arne_f@ipfire.org>
Tested-by: Yongqin Liu <yongqin.liu@linaro.org>
Tested-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Available on iOS/iPadOS >= 17, where this new interface is used by
developer tools using the new RemoteXPC protocol.
This private interface lacks a status endpoint, presumably because there
isn't a physical cable that can be unplugged, nor any speed changes to
be notified about.
Note that NCM interfaces are not exposed until a mode switch is
requested, which macOS does automatically.
The mode switch can be performed like this:
uint8_t status;
libusb_control_transfer(device_handle,
LIBUSB_RECIPIENT_DEVICE | LIBUSB_REQUEST_TYPE_VENDOR |
LIBUSB_ENDPOINT_IN,
82, /* bRequest */
0, /* wValue */
3, /* wIndex */
&status,
sizeof(status),
0);
Newer versions of usbmuxd do this automatically.
Co-developed-by: Håvard Sørbø <havard@hsorbo.no>
Signed-off-by: Håvard Sørbø <havard@hsorbo.no>
Signed-off-by: Ole André Vadla Ravnås <oleavr@frida.re>
Link: https://lore.kernel.org/r/20240607074117.31322-1-oleavr@frida.re
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some docks support MAC pass-through - MAC address
is taken from another device.
Driver should indicate that with NET_ADDR_STOLEN flag.
This should help to avoid collisions if network interface
names are generated with MAC policy.
Reported and discussed here
https://github.com/systemd/systemd/issues/33104
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605153340.25694-1-gmazyland@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we get to the end of the r8152's suspend() routine and we find that
the USB device is INACCESSIBLE then it means that some of our
preparation for suspend didn't take place. We need a USB reset to get
ourselves back in a consistent state so we can try again and that
can't happen during system suspend. Call pm_wakeup_event() to wake the
system up in this case.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f25.170a0220.8b5ad.1752@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we happened to get a USB transfer error during the transition to
suspend then the usb_queue_reset_device() that r8152_control_msg()
calls will get dropped on the floor. This is because
usb_lock_device_for_reset() (which usb_queue_reset_device() uses)
silently fails if it's called when a device is suspended or if too
much time passes.
Let's resolve this by resetting the device ourselves in r8152's
resume() function.
NOTE: due to timing, it's _possible_ that we could end up with two USB
resets: the one queued previously and the one called from the resume()
patch. This didn't happen in test cases I ran, though it's conceivably
possible. We can't easily know if this happened since
usb_queue_reset_device() can just silently drop the reset request. In
any case, it's not expected that this is a problem since the two
resets can't run at the same time (because of the device lock) and it
should be OK to reset the device twice. If somehow the double-reset
causes problems we could prevent resets from being queued up while
suspend is running.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/66590f22.170a0220.8b5ad.1750@mx.google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
EEPROM is detected
Enabled ASD/ADD configuration for LAN7801 in the absence of EEPROM.
After the lite reset these contents go back to defaults where ASD/
ADD is disabled. The check is already available for LAN7800.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20240529140256.1849764-3-rengarajan.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 125MHz and 25MHz clock configurations are enabled in the initialization
regardless of EEPROM (125MHz is needed for RGMII 1000Mbps operation). After
a lite reset (lan78xx_reset), these contents go back to defaults(all 0, so
no 125MHz or 25MHz clock).
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Link: https://lore.kernel.org/r/20240529140256.1849764-2-rengarajan.s@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/ti/icssg/icssg_classifier.c
abd5576b9c57 ("net: ti: icssg-prueth: Add support for ICSSG switch firmware")
56a5cf538c3f ("net: ti: icssg-prueth: Fix start counter for ft1 filter")
https://lore.kernel.org/all/20240531123822.3bb7eadf@canb.auug.org.au/
No other adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both lan78xx and smsc75xx have a 'usb_context'
struct which is unused, since their original commits.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20240526205922.176578-1-linux@treblig.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
LED Select (LED_SEL) bit in the LED General Purpose IO Configuration
register is used to determine the functionality of external LED pins
(Speed Indicator, Link and Activity Indicator, Full Duplex Link
Indicator). The default value for this bit is 0 when no EEPROM is
present. If a EEPROM is present, the default value is the value of the
LED Select bit in the Configuration Flags of the EEPROM. A USB Reset or
Lite Reset (LRST) will cause this bit to be restored to the image value
last loaded from EEPROM, or to be set to 0 if no EEPROM is present.
While configuring the dual purpose GPIO/LED pins to LED outputs in the
LED General Purpose IO Configuration register, the LED_SEL bit is changed
as 0 and resulting the configured value from the EEPROM is cleared. The
issue is fixed by using read-modify-write approach.
Fixes: f293501c61c5 ("smsc95xx: configure LED outputs")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Link: https://lore.kernel.org/r/20240523085314.167650-1-Parthiban.Veerasooran@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Merge in late fixes to prepare for the 6.10 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The idea was to keep only one reset at initialization stage in order to
reduce the total delay, or the reset from usbnet_probe or the reset from
usbnet_open.
I have seen that restarting from usbnet_probe is necessary to avoid doing
too complex things. But when the link is set to down/up (for example to
configure a different mac address) the link is not correctly recovered
unless a reset is commanded from usbnet_open.
So, detect the initialization stage (first call) to not reset from
usbnet_open after the reset from usbnet_probe and after this stage, always
reset from usbnet_open too (when the link needs to be rechecked).
Apply to all the possible devices, the behavior now is going to be the same.
cc: stable@vger.kernel.org # 6.6+
Fixes: 56f78615bcb1 ("net: usb: ax88179_178a: avoid writing the mac address before first reading")
Reported-by: Isaac Ganoung <inventor500@vivaldi.net>
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510090846.328201-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
v3: also fix a sparse error ( https://lore.kernel.org/oe-kbuild-all/202405091310.KvncIecx-lkp@intel.com/ )
v2: leave the skb_trim() game because smsc95xx_rx_csum_offload()
needs the csum part. (Jakub)
While we are it, use get_unaligned() in smsc95xx_rx_csum_offload().
Fixes: 2f7ca802bdae ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: UNGLinuxDriver@microchip.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509083313.2113832-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Link: https://lore.kernel.org/r/20240506142358.3657918-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd9642 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c94510 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Someone complains the message appears continuously. This occurs
because the device is woken from UPS mode, and the driver re-loads
the firmware.
When the device enters runtime suspend and cable is unplugged, the
device would enter UPS mode. If the runtime resume occurs, and the
device is woken from UPS mode, the driver has to re-load the firmware
and causes the message. If someone wakes the device continuously, the
message would be shown continuously, too. Use dev_dbg to avoid it.
Note that, the function could be called before register_netdev(), so I
don't use netif_info() or netif_dbg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20240424084532.159649-1-hayeswang@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To avoid the failure of usbnet_get_endpoints(), we should check the
return value of the usbnet_get_endpoints().
Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240424065634.1870027-1-make_ruc2021@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/ti/icssg/icssg_prueth.c
net/mac80211/chan.c
89884459a0b9 ("wifi: mac80211: fix idle calculation with multi-link")
87f5500285fb ("wifi: mac80211: simplify ieee80211_assign_link_chanctx()")
https://lore.kernel.org/all/20240422105623.7b1fbda2@canb.auug.org.au/
net/unix/garbage.c
1971d13ffa84 ("af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc().")
4090fa373f0e ("af_unix: Replace garbage collection algorithm.")
drivers/net/ethernet/ti/icssg/icssg_prueth.c
drivers/net/ethernet/ti/icssg/icssg_common.c
4dcd0e83ea1d ("net: ti: icssg-prueth: Fix signedness bug in prueth_init_rx_chns()")
e2dc7bfd677f ("net: ti: icssg-prueth: Move common functions into a separate file")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize overide.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path")
Fixes: f8ebb3ac881b ("net: usb: ax88179_178a: Fix packet receiving")
Reported-by: shironeko <shironeko@tesaguri.club>
Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jose Alonso <joalonsof@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the following Telit FN920C04 compositions:
0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a0 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a4 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T: Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a9 Rev=05.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=92c4c4d8
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/trace/events/rpcgss.h
386f4a737964 ("trace: events: cleanup deprecated strncpy uses")
a4833e3abae1 ("SUNRPC: Fix rpcgss_context trace event acceptor field")
Adjacent changes:
drivers/net/ethernet/intel/ice/ice_tc_lib.c
2cca35f5dd78 ("ice: Fix checking for unsupported keys on non-tunnel device")
784feaa65dfd ("ice: Add support for PFCP hardware offload in switchdev")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After the commit d2689b6a86b9 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.
In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.
Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86b9 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the qmi_wwan driver support for the Rolling
LTE modules.
- VID:PID 33f8:0104, RW101-GL for laptop debug M.2 cards(with RMNET
interface for /Linux/Chrome OS)
0x0104: RMNET, diag, at, pipe
Here are the outputs of usb-devices:
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1
P: Vendor=33f8 ProdID=0104 Rev=05.04
S: Manufacturer=Rolling Wireless S.a.r.l.
S: Product=Rolling Module
S: SerialNumber=ba2eb033
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=05(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
Signed-off-by: Vanillan Wang <vanillanwang@163.com>
Link: https://lore.kernel.org/r/20240416120713.24777-1-vanillanwang@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the net usb qmi_wwan driver to support Longsung U8300/U9300.
Enabling DTR on this modem was necessary to ensure stable operation.
For U8300
Interface 4 is used by for QMI interface in stock firmware of U8300, the
router which uses U8300 modem. Free the interface up, to rebind it to
qmi_wwan driver.
Interface 5 is used by for ADB interface in stock firmware of U8300, the
router which uses U8300 modem. Free the interface up.
The proper configuration is:
Interface mapping is:
0: unknown (Debug), 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI, 5: ADB
T: Bus=05 Lev=01 Prnt=03 Port=02 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b05 Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
For U9300
Interface 1 is used by for ADB interface in stock firmware of U9300, the
router which uses U9300 modem. Free the interface up.
Interface 4 is used by for QMI interface in stock firmware of U9300, the
router which uses U9300 modem. Free the interface up, to rebind it to
qmi_wwan driver.
The proper configuration is:
Interface mapping is:
0: ADB, 1: AT (Modem), 2: AT, 3: PPP (NDIS / Pipe), 4: QMI
Note: Interface 3 of some models of the U9300 series can send AT commands.
T: Bus=05 Lev=01 Prnt=05 Port=04 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b3c Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
Tested successfully using Modem Manager on U9300.
Tested successfully using qmicli on U9300.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://lore.kernel.org/r/20240415142638.1756966-1-coiaprant@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 3e2f544dd8a33 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the qmi_wwan driver and leverage the network
core allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240409133307.2058099-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enabling/disabling of EEE in the MAC should happen as a result of
auto negotiation. So move the enable/disable into
lan783xx_phy_link_status_change() which gets called by phylib when
there is a change in link status.
lan78xx_set_eee() now just programs the hardware with the LPI
timer value, and passed everything else to phylib, so it can correctly
setup the PHY.
lan743x_get_eee() relies on phylib doing most of the work, the
MAC driver just adds the LPI timer value.
Call phy_support_eee() to indicate the MAC does actually support EEE.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the mac address can not be read from the device registers or the
devicetree, a random address is generated, but this was already done from
usbnet_probe, so it is not necessary to call eth_hw_addr_random from here
again to generate another random address.
Indeed, when reset was also executed from bind, generate another random mac
address invalidated the check from usbnet_probe to configure if the assigned
mac address for the interface was random or not, because it is comparing
with the initial generated random address. Now, with only a reset from open
operation, it is just a harmless simplification.
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
