docs: misc-devices/c2port.txt: convert to ReST format

- Use copyright symbol;
- use title markups;
- adjust indentation;
- mark literal blocks as such.

Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
[jc: reverted |copy| change]
Link: https://lore.kernel.org/r/b3b2f3f58a9a33f9e8526d4fa36bee305ea4da38.1592203650.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

1 files changed, 0 insertions, 90 deletions

diff --git a/Documentation/misc-devices/c2port.txt b/Documentation/misc-devices/c2port.txt
deleted file mode 100644
index 31351b1a5a1f..000000000000
--- a/Documentation/misc-devices/c2port.txt
+++ /dev/null
@@ -1,90 +0,0 @@
-			C2 port support
-			---------------
-
-(C) Copyright 2007 Rodolfo Giometti <giometti@enneenne.com>
-
-This program is free software; you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation; either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-
-
-Overview
---------
-
-This driver implements the support for Linux of Silicon Labs (Silabs)
-C2 Interface used for in-system programming of micro controllers.
-
-By using this driver you can reprogram the in-system flash without EC2
-or EC3 debug adapter. This solution is also useful in those systems
-where the micro controller is connected via special GPIOs pins.
-
-References
-----------
-
-The C2 Interface main references are at (https://www.silabs.com)
-Silicon Laboratories site], see:
-
-- AN127: FLASH Programming via the C2 Interface at
-https://www.silabs.com/Support Documents/TechnicalDocs/an127.pdf 
-
-- C2 Specification at
-https://www.silabs.com/pages/DownloadDoc.aspx?FILEURL=Support%20Documents/TechnicalDocs/an127.pdf&src=SearchResults
-
-however it implements a two wire serial communication protocol (bit
-banging) designed to enable in-system programming, debugging, and
-boundary-scan testing on low pin-count Silicon Labs devices. Currently
-this code supports only flash programming but extensions are easy to
-add.
-
-Using the driver
-----------------
-
-Once the driver is loaded you can use sysfs support to get C2port's
-info or read/write in-system flash.
-
-# ls /sys/class/c2port/c2port0/
-access            flash_block_size  flash_erase       rev_id
-dev_id            flash_blocks_num  flash_size        subsystem/
-flash_access      flash_data        reset             uevent
-
-Initially the C2port access is disabled since you hardware may have
-such lines multiplexed with other devices so, to get access to the
-C2port, you need the command:
-
-# echo 1 > /sys/class/c2port/c2port0/access
-
-after that you should read the device ID and revision ID of the
-connected micro controller:
-
-# cat /sys/class/c2port/c2port0/dev_id
-8
-# cat /sys/class/c2port/c2port0/rev_id
-1
-
-However, for security reasons, the in-system flash access in not
-enabled yet, to do so you need the command:
-
-# echo 1 > /sys/class/c2port/c2port0/flash_access
-
-After that you can read the whole flash:
-
-# cat /sys/class/c2port/c2port0/flash_data > image
-
-erase it:
-
-# echo 1 > /sys/class/c2port/c2port0/flash_erase
-
-and write it:
-
-# cat image > /sys/class/c2port/c2port0/flash_data
-
-after writing you have to reset the device to execute the new code:
-
-# echo 1 > /sys/class/c2port/c2port0/reset