Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 634 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
new file mode 100644
index 000000000000..815119c12bd4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Tolino Shine 2 HD ebook reader
+ *
+ * Name on mainboard is: 37NB-E60QF0+4A2 or 37NB-E60QF0+4A3
+ * Serials start with: E60QF2
+ *
+ * Copyright 2020 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Tolino Shine 2 HD";
+	compatible = "kobo,tolino-shine2hd", "fsl,imx6sl";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-fl {
+			label = "Frontlight";
+			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BRIGHTNESS_CYCLE>;
+		};
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led-0 {
+			label = "tolinoshine2hd:white:on";
+			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		led-1 {
+			label = "tolinoshine2hd:white:backlightboost";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	ec: embedded-controller@43 {
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		#pwm-cells = <2>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	zforce: touchscreen@50 {
+		compatible = "neonode,zforce";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_zforce>;
+		reg = <0x50>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&ldo1_reg>;
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		x-size = <1072>;
+		y-size = <1448>;
+	};
+
+	/* TODO: TPS65185 PMIC for E Ink at 0x68 */
+
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ricoh619: pmic@32 {
+		compatible = "ricoh,rc5t619";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ricoh_gpio>;
+		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+
+		regulators {
+			dcdc1_reg: DCDC1 {
+				regulator-name = "DCDC1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <900000>;
+					regulator-suspend-min-microvolt = <900000>;
+				};
+			};
+
+			/* Core3_3V3 */
+			dcdc2_reg: DCDC2 {
+				regulator-name = "DCDC2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3100000>;
+					regulator-suspend-min-microvolt = <3100000>;
+				};
+			};
+
+			dcdc3_reg: DCDC3 {
+				regulator-name = "DCDC3";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V2 */
+			dcdc4_reg: DCDC4 {
+				regulator-name = "DCDC4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V8 */
+			dcdc5_reg: DCDC5 {
+				regulator-name = "DCDC5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1700000>;
+					regulator-suspend-min-microvolt = <1700000>;
+				};
+			};
+
+			/* IR_3V3 */
+			ldo1_reg: LDO1  {
+				regulator-name = "LDO1";
+				regulator-boot-on;
+			};
+
+			/* Core1_3V3 */
+			ldo2_reg: LDO2  {
+				regulator-name = "LDO2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3000000>;
+					regulator-suspend-min-microvolt = <3000000>;
+				};
+			};
+
+			/* Core5_1V2 */
+			ldo3_reg: LDO3  {
+				regulator-name = "LDO3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-boot-on;
+			};
+
+			/* SPD_3V3 */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* DDR_0V6 */
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* VDD_PWM */
+			ldo7_reg: LDO7 {
+				regulator-name = "LDO7";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* ldo_1v8 */
+			ldo8_reg: LDO8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "LDO9";
+				regulator-boot-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "LDO10";
+				regulator-boot-on;
+			};
+
+			ldortc1_reg: LDORTC1  {
+				regulator-name = "LDORTC1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x17059
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x17059
+			MX6SL_PAD_KEY_COL1__GPIO3_IO26  0x17059
+			MX6SL_PAD_KEY_ROW0__GPIO3_IO25  0x17059
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SL_PAD_LCD_DAT0__GPIO2_IO20	0x79
+			MX6SL_PAD_LCD_DAT1__GPIO2_IO21	0x79
+			MX6SL_PAD_LCD_DAT2__GPIO2_IO22	0x79
+			MX6SL_PAD_LCD_DAT3__GPIO2_IO23	0x79
+			MX6SL_PAD_LCD_DAT4__GPIO2_IO24	0x79
+			MX6SL_PAD_LCD_DAT5__GPIO2_IO25	0x79
+			MX6SL_PAD_LCD_DAT6__GPIO2_IO26	0x79
+			MX6SL_PAD_LCD_DAT7__GPIO2_IO27	0x79
+			MX6SL_PAD_LCD_DAT8__GPIO2_IO28	0x79
+			MX6SL_PAD_LCD_DAT9__GPIO2_IO29	0x79
+			MX6SL_PAD_LCD_DAT10__GPIO2_IO30	0x79
+			MX6SL_PAD_LCD_DAT11__GPIO2_IO31	0x79
+			MX6SL_PAD_LCD_DAT12__GPIO3_IO00	0x79
+			MX6SL_PAD_LCD_DAT13__GPIO3_IO01	0x79
+			MX6SL_PAD_LCD_DAT14__GPIO3_IO02	0x79
+			MX6SL_PAD_LCD_DAT15__GPIO3_IO03	0x79
+			MX6SL_PAD_LCD_DAT16__GPIO3_IO04	0x79
+			MX6SL_PAD_LCD_DAT17__GPIO3_IO05	0x79
+			MX6SL_PAD_LCD_DAT18__GPIO3_IO06	0x79
+			MX6SL_PAD_LCD_DAT19__GPIO3_IO07	0x79
+			MX6SL_PAD_LCD_DAT20__GPIO3_IO08	0x79
+			MX6SL_PAD_LCD_DAT21__GPIO3_IO09	0x79
+			MX6SL_PAD_LCD_DAT22__GPIO3_IO10	0x79
+			MX6SL_PAD_LCD_DAT23__GPIO3_IO11	0x79
+			MX6SL_PAD_LCD_CLK__GPIO2_IO15		0x79
+			MX6SL_PAD_LCD_ENABLE__GPIO2_IO16	0x79
+			MX6SL_PAD_LCD_HSYNC__GPIO2_IO17	0x79
+			MX6SL_PAD_LCD_VSYNC__GPIO2_IO18	0x79
+			MX6SL_PAD_LCD_RESET__GPIO2_IO19	0x79
+			MX6SL_PAD_KEY_COL3__GPIO3_IO30		0x79
+			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
+			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
+			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x79
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh_gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CLK__GPIO5_IO15	0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11	0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28	0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+
+	pinctrl_zforce: zforcegrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06		0x17059 /* TP_INT */
+			MX6SL_PAD_SD1_DAT5__GPIO5_IO09		0x10059 /* TP_RST */
+		>;
+	};
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_arm {
+	vin-supply = <&dcdc3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4, through-holes */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	non-removable;
+	status = "okay";
+
+	/* internal uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * 37NB-E60QF0+4A2: CyberTan WC121 (BCM43362) SDIO WiFi
+	 * 37NB-E60QF0+4A3: RTL8189F SDIO WiFi
+	 */
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};