Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 603 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
new file mode 100644
index 000000000000..a2c79bcf9a11
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
@@ -0,0 +1,603 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright (C) 2016 Boundary Devices, Inc.
+ */
+
+/dts-v1/;
+
+#include "imx6sx.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX6 SoloX Nitrogen6sx Board";
+	compatible = "boundary,imx6sx-nitrogen6sx", "fsl,imx6sx";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		power-supply = <&reg_3p3v>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_can1_3v3: regulator-can1-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can1-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can2_3v3: regulator-can2-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can2-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1_vbus>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wlan: regulator-wlan {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_wlan>;
+		compatible = "regulator-fixed";
+		clocks = <&clks IMX6SX_CLK_CKO>;
+		clock-names = "slow";
+		regulator-name = "wlan-en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+		gpio = <&gpio7 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6sx-nitrogen6sx-sgtl5000";
+		cpu-dai = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <5>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "microchip,sst25vf016b";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "U-Boot";
+			reg = <0x0 0xc0000>;
+			read-only;
+		};
+
+		partition@c0000 {
+			label = "env";
+			reg = <0xc0000 0x2000>;
+			read-only;
+		};
+
+		partition@c2000 {
+			label = "Kernel";
+			reg = <0xc2000 0x11e000>;
+		};
+
+		partition@1e0000 {
+			label = "M4";
+			reg = <0x1e0000 0x20000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_3p3v>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@4 {
+			reg = <4>;
+		};
+
+		ethphy2: ethernet-phy@5 {
+			reg = <5>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+	phy-supply = <&reg_3p3v>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_3v3>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_3v3>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		clocks = <&clks IMX6SX_CLK_CKO2>;
+		VDDA-supply = <&reg_1p8v>;
+		VDDIO-supply = <&reg_1p8v>;
+		VDDD-supply = <&reg_1p8v>;
+		assigned-clocks = <&clks IMX6SX_CLK_CKO2_SEL>,
+				  <&clks IMX6SX_CLK_CKO2>;
+		assigned-clock-parents = <&clks IMX6SX_CLK_OSC>;
+		assigned-clock-rates = <0>, <24000000>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 10 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm4 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	dr_mode = "host";
+	disable-over-current;
+	reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	non-removable;
+	keep-power-in-suspend;
+	vmmc-supply = <&reg_wlan>;
+	cap-power-off-card;
+	cap-sdio-irq;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&gpio7>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+&usdhc4 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&reg_1p8v>;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD1_DATA0__AUDMUX_AUD5_RXD	0x1b0b0
+			MX6SX_PAD_SD1_DATA1__AUDMUX_AUD5_TXC	0x1b0b0
+			MX6SX_PAD_SD1_DATA2__AUDMUX_AUD5_TXFS	0x1b0b0
+			MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_TXD	0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL1__ECSPI1_MISO		0x100b1
+			MX6SX_PAD_KEY_ROW0__ECSPI1_MOSI		0x100b1
+			MX6SX_PAD_KEY_COL0__ECSPI1_SCLK		0x100b1
+			MX6SX_PAD_KEY_ROW1__GPIO2_IO_16		0x0b0b1
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0x1b0b0
+			MX6SX_PAD_ENET1_MDC__ENET1_MDC		0x1b0b0
+			MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0x30b1
+			MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0x30b1
+			MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2	0x30b1
+			MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3	0x30b1
+			MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC	0x30b1
+			MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0x30b1
+			MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081
+			MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK	0x3081
+			MX6SX_PAD_ENET2_CRS__GPIO2_IO_7		0xb0b0
+			MX6SX_PAD_ENET1_RX_CLK__GPIO2_IO_4	0xb0b0
+			MX6SX_PAD_ENET1_TX_CLK__GPIO2_IO_5	0xb0b0
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0x30b1
+			MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0x30b1
+			MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2	0x30b1
+			MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3	0x30b1
+			MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC	0x30b1
+			MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0x30b1
+			MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x3081
+			MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK	0x3081
+			MX6SX_PAD_ENET2_COL__GPIO2_IO_6		0xb0b0
+			MX6SX_PAD_ENET2_RX_CLK__GPIO2_IO_8	0xb0b0
+			MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9	0xb0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DQS__CAN1_TX		0x1b0b0
+			MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX		0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA3__GPIO4_IO_27	0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA3__GPIO4_IO_27	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1A_DQS__CAN2_TX		0x1b0b0
+			MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX		0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA0__GPIO4_IO_24	0x0b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_CE0_B__GPIO4_IO_1	0x1b0b0
+			MX6SX_PAD_NAND_CLE__GPIO4_IO_3		0x1b0b0
+			MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x1b0b0
+			MX6SX_PAD_NAND_WE_B__GPIO4_IO_14	0x1b0b0
+			MX6SX_PAD_NAND_WP_B__GPIO4_IO_15	0x1b0b0
+			MX6SX_PAD_NAND_READY_B__GPIO4_IO_13	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA1__GPIO4_IO_17	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA2__GPIO4_IO_18	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19	0x1b0b0
+			MX6SX_PAD_SD1_CMD__CCM_CLKO1		0x000b0
+			MX6SX_PAD_SD3_DATA5__GPIO7_IO_7		0x1b0b0
+			/* Test points */
+			MX6SX_PAD_NAND_DATA04__GPIO4_IO_8	0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA1__GPIO4_IO_25	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO02__I2C2_SCL		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO03__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL4__I2C3_SCL		0x4001b8b1
+			MX6SX_PAD_KEY_ROW4__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_DATA05__GPIO4_IO_9	0xb0b0
+			MX6SX_PAD_NAND_DATA06__GPIO4_IO_10	0xb0b0
+			MX6SX_PAD_NAND_DATA07__GPIO4_IO_11	0xb0b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO13__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_reg_wlan: reg-wlangrp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_DATA4__GPIO7_IO_6		0x1b0b0
+			MX6SX_PAD_GPIO1_IO11__CCM_CLKO1		0x000b0
+		>;
+	};
+
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO12__CCM_CLKO2		0x000b0
+			MX6SX_PAD_ENET1_COL__GPIO2_IO_0		0x1b0b0
+			MX6SX_PAD_ENET1_CRS__GPIO2_IO_1		0x1b0b0
+			MX6SX_PAD_QSPI1A_SS0_B__GPIO4_IO_22	0xb0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_SS0_B__UART3_DCE_TX		0x1b0b1
+			MX6SX_PAD_QSPI1B_SCLK__UART3_DCE_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL3__UART5_DCE_TX		0x1b0b1
+			MX6SX_PAD_KEY_ROW3__UART5_DCE_RX		0x1b0b1
+			MX6SX_PAD_SD3_DATA6__UART3_DCE_RTS		0x1b0b1
+			MX6SX_PAD_SD3_DATA7__UART3_DCE_CTS		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x1b0b0
+			MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x170b1
+		>;
+	};
+
+	pinctrl_usbotg1_vbus: usbotg1-vbusgrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DATA2__GPIO4_IO_26	0xb0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059
+			MX6SX_PAD_KEY_COL2__GPIO2_IO_12		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x10071
+			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x17071
+			MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x17071
+			MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x17071
+			MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x17071
+			MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x17071
+		>;
+	};
+
+	pinctrl_usdhc4_50mhz: usdhc4-50mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10071
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17071
+			MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B	0x17071
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x17071
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x17071
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x17071
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x17071
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x17071
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x17071
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x17071
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x17071
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100b9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170b9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170b9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170b9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170b9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170b9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170b9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170b9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170b9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100f9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170f9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170f9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170f9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170f9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170f9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170f9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170f9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170f9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170f9
+		>;
+	};
+};