Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

79 files changed, 24851 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
new file mode 100644
index 000000000000..3dfb1c8cefb8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_QCOM) += \
+	qcom-apq8016-sbc.dtb \
+	qcom-apq8026-asus-sparrow.dtb \
+	qcom-apq8026-huawei-sturgeon.dtb \
+	qcom-apq8026-lg-lenok.dtb \
+	qcom-apq8026-samsung-matisse-wifi.dtb \
+	qcom-apq8060-dragonboard.dtb \
+	qcom-apq8064-cm-qs600.dtb \
+	qcom-apq8064-ifc6410.dtb \
+	qcom-apq8064-sony-xperia-lagan-yuga.dtb \
+	qcom-apq8064-asus-nexus7-flo.dtb \
+	qcom-apq8074-dragonboard.dtb \
+	qcom-apq8084-ifc6540.dtb \
+	qcom-apq8084-mtp.dtb \
+	qcom-ipq4018-ap120c-ac.dtb \
+	qcom-ipq4018-ap120c-ac-bit.dtb \
+	qcom-ipq4018-jalapeno.dtb \
+	qcom-ipq4019-ap.dk01.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c3.dtb \
+	qcom-ipq4019-ap.dk07.1-c1.dtb \
+	qcom-ipq4019-ap.dk07.1-c2.dtb \
+	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
+	qcom-msm8226-samsung-s3ve3g.dtb \
+	qcom-msm8660-surf.dtb \
+	qcom-msm8916-samsung-e5.dtb \
+	qcom-msm8916-samsung-e7.dtb \
+	qcom-msm8916-samsung-grandmax.dtb \
+	qcom-msm8916-samsung-serranove.dtb \
+	qcom-msm8960-cdp.dtb \
+	qcom-msm8960-samsung-expressatt.dtb \
+	qcom-msm8974-lge-nexus5-hammerhead.dtb \
+	qcom-msm8974-sony-xperia-rhine-amami.dtb \
+	qcom-msm8974-sony-xperia-rhine-honami.dtb \
+	qcom-msm8974pro-fairphone-fp2.dtb \
+	qcom-msm8974pro-oneplus-bacon.dtb \
+	qcom-msm8974pro-samsung-klte.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
+	qcom-mdm9615-wp8548-mangoh-green.dtb \
+	qcom-sdx55-mtp.dtb \
+	qcom-sdx55-t55.dtb \
+	qcom-sdx55-telit-fn980-tlb.dtb \
+	qcom-sdx65-mtp.dtb
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
new file mode 100644
index 000000000000..4ccd2dca74a2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/apq8016-sbc.dts"
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
new file mode 100644
index 000000000000..aa0e0e8d2a97
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "ASUS ZenWatch 2";
+	compatible = "asus,sparrow", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 3005>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart1_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a1-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <350000>;
+	qcom,fast-charge-safe-voltage = <4430000>;
+	qcom,fast-charge-high-threshold-voltage = <4400000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4400000>;
+};
+
+&tlmm {
+	blsp1_uart1_default_state: blsp1-uart1-default-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "blsp_uart1";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio48", "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
new file mode 100644
index 000000000000..de19640efe55
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+#include <dt-bindings/input/ti-drv260x.h>
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "Huawei Watch";
+	compatible = "huawei,sturgeon", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 4>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	vibrator@5a {
+		compatible = "ti,drv2605";
+		reg = <0x5a>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+
+		mode = <DRV260X_ERM_MODE>;
+		library-sel = <DRV260X_ERM_LIB_D>;
+		vib-rated-mv = <2765>;
+		vib-overdrive-mv = <3525>;
+
+		pinctrl-0 = <&vibrator_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_i2c5 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vio-supply = <&pm8226_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_3 {
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-voltage = <4370000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,minimum-input-voltage = <4350000>;
+	qcom,fast-charge-current-limit = <300000>;
+	qcom,fast-charge-safe-current = <600000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio63", "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	touch_default_state: touch-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	vibrator_default_state: vibrator-default-state {
+		pins = "gpio59", "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
new file mode 100644
index 000000000000..b887e5361ec3
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "LG G Watch R";
+	compatible = "lg,lenok", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,board-id = <132 0x0a>;
+	qcom,msm-id = <199 0x20000>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x03100000 0x200000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3300000 {
+			reg = <0x03300000 0x1400000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27421";
+		reg = <0x55>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+	clock-frequency = <384000>;
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l22>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&blsp1_uart4 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <450000>;
+	qcom,fast-charge-current-limit = <400000>;
+	qcom,fast-charge-safe-voltage = <4350000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	touch_pins: touch-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-pull-down;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio37";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..884d99297d4c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,519 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &smem_region;
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1";
+	compatible = "samsung,matisse-wifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <1280>;
+			height = <800>;
+			stride = <(1280 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+			interrupts = <&tlmm 110 IRQ_TYPE_EDGE_FALLING>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-backlight {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&backlight_i2c_default_state>;
+		pinctrl-names = "default";
+
+		i2c-gpio,delay-us = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x3f>;
+
+			pwms = <&backlight_pwm 0 100000>;
+			pwm-names = "lp8556";
+
+			rom-a0h {
+				rom-addr = /bits/ 8 <0xa0>;
+				rom-val = /bits/ 8 <0x44>;
+			};
+
+			rom-a1h {
+				rom-addr = /bits/ 8 <0xa1>;
+				rom-val = /bits/ 8 <0x6c>;
+			};
+
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x24>;
+			};
+		};
+	};
+
+	backlight_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		clocks = <&mmcc CAMSS_GP0_CLK>;
+		pinctrl-0 = <&backlight_pwm_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en_default_state>;
+	};
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp_region: adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default_state>;
+
+		st,drdy-int-pin = <1>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&muic_int_default_state>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+
+		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&reg_tsp_1p8v>;
+		vdda-supply = <&reg_tsp_3p3v>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_i2c_default_state: backlight-i2c-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_pwm_default_state: backlight-pwm-default-state {
+		pins = "gpio33";
+		function = "gp0_clk";
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio73";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
new file mode 100644
index 000000000000..db4c791b2e2f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,973 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Main power of the board: 3.7V */
+	vph: regulator-fixed {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-name = "VPH";
+		regulator-type = "voltage";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* GPIO controlled ethernet power regulator */
+	dragon_veth: xc622a331mrg {
+		compatible = "regulator-fixed";
+		regulator-name = "XC6222A331MR-G";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vph>;
+		gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_veth_gpios>;
+		regulator-always-on;
+	};
+
+	/* VDDvario fixed regulator */
+	dragon_vario: nds332p {
+		compatible = "regulator-fixed";
+		regulator-name = "NDS332P";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&pm8058_s3>;
+	};
+
+	/* This is a levelshifter for SDCC5 */
+	dragon_vio_txb: txb0104rgyr {
+		compatible = "regulator-fixed";
+		regulator-name = "Dragon SDCC levelshifter";
+		vin-supply = <&pm8058_l14>;
+		regulator-always-on;
+	};
+
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&xoadc 0x00 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+};
+
+&ebi2 {
+	/* The EBI2 will instantiate first, then populate its children */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_ebi2_pins>;
+	status = "okay";
+
+	/*
+	 * An on-board SMSC LAN9221 chip for "debug ethernet",
+	 * which is actually just an ordinary ethernet on the
+	 * EBI2. This has a 25MHz chrystal next to it, so no
+	 * clocking is needed.
+	 */
+	ethernet@2,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <2 0x0 0x100>;
+		/*
+		 * The second interrupt is the PME interrupt
+		 * for network wakeup, connected to the TLMM.
+		 */
+		interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+				    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		vdd33a-supply = <&dragon_veth>;
+		vddvario-supply = <&dragon_vario>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ethernet_gpios>;
+		phy-mode = "mii";
+		reg-io-width = <2>;
+		smsc,force-external-phy;
+		smsc,irq-push-pull;
+
+		/*
+		 * SLOW chipselect config
+		 * Delay 9 cycles (140ns@64MHz) between SMSC
+		 * LAN9221 Ethernet controller reads and writes
+		 * on CS2.
+		 */
+		qcom,xmem-recovery-cycles = <0>;
+		qcom,xmem-write-hold-cycles = <3>;
+		qcom,xmem-write-delta-cycles = <31>;
+		qcom,xmem-read-delta-cycles = <28>;
+		qcom,xmem-write-wait-cycles = <9>;
+		qcom,xmem-read-wait-cycles = <9>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,cy8ctma340";
+		reg = <0x24>;
+		/* Certainly we can do at least 400 kHz */
+		clock-frequency = <400000>;
+		/* IRQ on GPIO61 called /CTP_INT */
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * The I2C bus is using a PCA9306 level translator from L16A
+		 * to L2B so these two voltages are needed and L16A is
+		 * kind of the IO voltage, however L16Aisn't really fed to
+		 * the TMA340, which relies entirely on L2B (PM8901 L2).
+		 */
+		vcpin-supply = <&pm8058_l16>;
+		vdd-supply = <&pm8901_l2>;
+		/* GPIO58, called WAKE_CTP */
+		reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		active-interval-ms = <0>;
+		touch-timeout-ms = <255>;
+		lowpower-interval-ms = <10>;
+		bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_tma340_gpios>;
+	};
+};
+
+&gsbi8 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi8_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+	status = "okay";
+
+	eeprom@52 {
+		/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		vcc-supply = <&pm8058_s3>;
+		pagesize = <64>;
+	};
+	wm8903: wm8903@1a {
+		/* This Woolfson Micro device has an unrouted interrupt line */
+		compatible = "wlf,wm8903";
+		reg = <0x1a>;
+
+		AVDD-supply = <&pm8058_l16>;
+		CPVDD-supply = <&pm8058_l16>;
+		DBVDD-supply = <&pm8058_s3>;
+		DCVDD-supply = <&pm8058_l0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		micdet-cfg = <0>;
+		micdet-delay = <100>;
+		gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+	status = "okay";
+};
+
+&gsbi12_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+	status = "okay";
+
+	ak8975@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ak8975_gpios>;
+		vid-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+	};
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_bmp085_gpios>;
+		vddd-supply = <&pm8058_lvs0>; // 1.8V
+		vdda-supply = <&pm8058_l14>; // 2.85V
+	};
+	mpu3050@68 {
+		compatible = "invensense,mpu3050";
+		reg = <0x68>;
+		/*
+		 * GPIO17 is pulled high by a 10k
+		 * resistor to VLOGIC so needs to be
+		 * active low/falling edge.
+		 */
+		interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_mpu3050_gpios>;
+		vlogic-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+
+		/*
+		 * The MPU-3050 acts as a hub for the
+		 * accelerometer.
+		 */
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			kxsd9@18 {
+				compatible = "kionix,kxsd9";
+				reg = <0x18>;
+				interrupt-parent = <&tlmm>;
+				interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_kxsd9_gpios>;
+				iovdd-supply = <&pm8058_lvs0>; // 1.8V
+				vdd-supply = <&pm8058_l14>; // 2.85V
+			};
+		};
+	};
+};
+
+&pm8058_gpio {
+	dragon_ethernet_gpios: ethernet-state {
+		pinconf {
+			pins = "gpio7";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_bmp085_gpios: bmp085-state {
+		pinconf {
+			pins = "gpio16";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_mpu3050_gpios: mpu3050-state {
+		pinconf {
+			pins = "gpio17";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc3_gpios: sdcc3-state {
+		pinconf {
+			pins = "gpio22";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc5_gpios: sdcc5-state {
+		pinconf {
+			pins = "gpio26";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_ak8975_gpios: ak8975-state {
+		pinconf {
+			pins = "gpio33";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_cm3605_gpios: cm3605-state {
+		/* Pin 34 connected to the proxy IRQ */
+		gpio34-pins {
+			pins = "gpio34";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+		/* Pin 35 connected to ASET */
+		gpio35-pins {
+			pins = "gpio35";
+			function = "normal";
+			output-high;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_veth_gpios: veth-state {
+		pinconf {
+			pins = "gpio40";
+			function = "normal";
+			bias-disable;
+			drive-push-pull;
+		};
+	};
+};
+
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_MENU)
+		MATRIX_KEY(0, 2, KEY_1)
+		MATRIX_KEY(0, 3, KEY_4)
+		MATRIX_KEY(0, 4, KEY_7)
+		MATRIX_KEY(1, 0, KEY_UP)
+		MATRIX_KEY(1, 1, KEY_LEFT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_5)
+		MATRIX_KEY(1, 3, KEY_8)
+		MATRIX_KEY(2, 0, KEY_HOME)
+		MATRIX_KEY(2, 1, KEY_REPLY)
+		MATRIX_KEY(2, 2, KEY_2)
+		MATRIX_KEY(2, 3, KEY_6)
+		MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(3, 1, KEY_RIGHT)
+		MATRIX_KEY(3, 2, KEY_3)
+		MATRIX_KEY(3, 3, KEY_9)
+		MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+		MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+		MATRIX_KEY(4, 1, KEY_BACK)
+		MATRIX_KEY(4, 2, KEY_CAMERA)
+		MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+	>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
+
+&pm8058_led48 {
+	/*
+	 * The keypad LED @0x48 is routed to
+	 * the sensor board where it is
+	 * connected to an infrared LED
+	 * SFH4650 (60mW, @850nm) next to the
+	 * ambient light and proximity sensor
+	 * Capella Microsystems CM3605.
+	 */
+	label = "pm8058:infrared:proximitysensor";
+	default-state = "off";
+	linux,default-trigger = "cm3605";
+	status = "okay";
+};
+
+&pm8058_led131 {
+	label = "pm8058:red";
+	color = <LED_COLOR_ID_RED>;
+	default-state = "off";
+	status = "okay";
+};
+
+&pm8058_led132 {
+	/*
+	 * This is actually green too on my
+	 * board, but documented as yellow.
+	 */
+	label = "pm8058:yellow";
+	color = <LED_COLOR_ID_YELLOW>;
+	default-state = "off";
+	linux,default-trigger = "mmc0";
+	status = "okay";
+};
+
+&pm8058_led133 {
+	label = "pm8058:green";
+	function = LED_FUNCTION_HEARTBEAT;
+	color = <LED_COLOR_ID_GREEN>;
+	default-state = "on";
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pm8058_mpps {
+	dragon_cm3605_mpps: cm3605-mpps-state {
+		pins = "mpp5";
+		function = "analog";
+		input-enable;
+		bias-high-impedance;
+		/* Let's use channel 5 */
+		qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+		power-source = <PM8058_GPIO_S3>;
+	};
+};
+
+&rpm {
+	/*
+	 * Set up of the PMIC RPM regulators for this board
+	 * PM8901 supplies "preliminary regulators" whatever
+	 * that means
+	 */
+	regulators-0 {
+		vdd_l0-supply = <&pm8901_s4>;
+		vdd_l1-supply = <&vph>;
+		vdd_l2-supply = <&vph>;
+		vdd_l3-supply = <&vph>;
+		vdd_l4-supply = <&vph>;
+		vdd_l5-supply = <&vph>;
+		vdd_l6-supply = <&vph>;
+		/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		lvs0_in-supply = <&pm8058_s3>;
+		lvs1_in-supply = <&pm8901_s4>;
+		lvs2_in-supply = <&pm8058_l0>;
+		lvs3_in-supply = <&pm8058_s2>;
+		mvs_in-supply = <&pm8058_s3>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l2 {
+			/* TMA340 requires strictly 3.3V */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		/* s0 and s1 are SAW regulators controlled over SPM */
+		s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* LVS0 thru 3 and mvs are just switches */
+		lvs0 {
+			regulator-always-on;
+		};
+		lvs1 { };
+		lvs2 { };
+		lvs3 { };
+		mvs { };
+
+	};
+
+	regulators-1 {
+		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+		vdd_l2_l11_l12-supply = <&vph>;
+		vdd_l3_l4_l5-supply = <&vph>;
+		vdd_l6_l7-supply = <&vph>;
+		vdd_l8-supply = <&vph>;
+		vdd_l9-supply = <&vph>;
+		vdd_l10-supply = <&vph>;
+		vdd_l13_l16-supply = <&pm8058_s4>;
+		vdd_l14_l15-supply = <&vph>;
+		vdd_l17_l18-supply = <&vph>;
+		vdd_l19_l20-supply = <&vph>;
+		vdd_l21-supply = <&pm8058_s3>;
+		vdd_l22-supply = <&pm8058_s3>;
+		vdd_l23_l24_l25-supply = <&pm8058_s3>;
+		vdd_s0-supply = <&vph>;
+		vdd_s1-supply = <&vph>;
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		vdd_ncp-supply = <&vph>;
+
+		l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l4 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3600000>;
+			bias-pull-down;
+		};
+		l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3050000>;
+			bias-pull-down;
+		};
+		l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l10 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l11 {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+		l12 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+		l13 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			bias-pull-down;
+		};
+		l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+		l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l17 {
+			// 1.5V according to schematic
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+		l18 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+		l19 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			bias-pull-down;
+		};
+		l20 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+		l21 {
+			// 1.1 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+		l22 {
+			// 1.2 V according to schematic
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+		l23 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l24 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+		l25 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		s0 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1325000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s1 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1250000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s2 {
+			// 1.3 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+		s4 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		/* LVS0 and LVS1 are just switches */
+		lvs0 {
+			bias-pull-down;
+		};
+		lvs1 {
+			bias-pull-down;
+		};
+
+		ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* Internal 3.69 GiB eMMC */
+&sdcc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc1_pins>;
+	vmmc-supply = <&pm8901_l5>;
+	vqmmc-supply = <&pm8901_lvs0>;
+	status = "okay";
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+	/* Enable SSBI GPIO 22 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+	cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	status = "okay";
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+	/* Enable SSBI GPIO 26 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+	cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	vqmmc-supply = <&dragon_vio_txb>;
+	status = "okay";
+};
+
+&tlmm {
+	/* eMMC pins, all 8 data lines connected */
+	dragon_sdcc1_pins: sdcc1-state {
+		clk-pins {
+			pins = "gpio167"; /* SDC1 CLK */
+			function = "sdc1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio168"; /* SDC1 CMD */
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC1 D0 to D7 */
+			pins = "gpio159", "gpio160", "gpio161", "gpio162",
+			     "gpio163", "gpio164", "gpio165", "gpio166";
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	/*
+	 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+	 * configuration.
+	 */
+	dragon_sdcc3_pins: sdcc3-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	/* Second SD card slot pins */
+	dragon_sdcc5_pins: sdcc5-state {
+		clk-pins {
+			pins = "gpio97"; /* SDC5 CLK */
+			function = "sdc5";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio95"; /* SDC5 CMD */
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC5 D0 to D3 */
+			pins = "gpio96", "gpio98", "gpio99", "gpio100";
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_gsbi3_i2c_pins: gsbi3-i2c-state {
+		pins = "gpio43", "gpio44";
+		function = "gsbi3";
+		drive-strength = <8>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi8_i2c_pins: gsbi8-i2c-state {
+		pins = "gpio64", "gpio65";
+		function = "gsbi8";
+		drive-strength = <16>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi12_i2c_pins: gsbi12-i2c-state {
+		pins = "gpio115", "gpio116";
+		function = "gsbi12";
+		drive-strength = <16>;
+		/* These have external pull-up 4.7kOhm to 1.8V */
+		bias-disable;
+	};
+
+	/* Primary serial port uart 0 pins */
+	dragon_gsbi12_serial_pins: gsbi12-serial-state {
+		tx-pins {
+			pins = "gpio117";
+			function = "gsbi12";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		rx-pins {
+			pins = "gpio118";
+			function = "gsbi12";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_ebi2_pins: ebi2-state {
+		/*
+		 * Pins used by EBI2 on the Dragonboard, actually only
+		 * CS2 is used by a real peripheral. CS0 is just
+		 * routed to a test point.
+		 */
+		mux0-pins {
+			pins =
+			    /* "gpio39", CS1A_N this is not good to mux */
+			    "gpio40", /* CS2A_N */
+			    "gpio134"; /* CS0_N testpoint TP29 */
+			function = "ebi2cs";
+		};
+		mux1-pins {
+			pins =
+			    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+			    "gpio123", "gpio124", "gpio125", "gpio126",
+			    "gpio127", "gpio128", "gpio129", "gpio130",
+			    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+			    "gpio135", "gpio136", "gpio137", "gpio138",
+			    "gpio139", "gpio140", "gpio141", "gpio142",
+			    "gpio143", "gpio144", "gpio145", "gpio146",
+			    "gpio147", "gpio148", "gpio149", "gpio150",
+			    "gpio151", /* EBI2_OE_N */
+			    "gpio153", /* EBI2_ADV */
+			    "gpio157"; /* EBI2_WE_N */
+			function = "ebi2";
+		};
+	};
+
+	/* Interrupt line for the KXSD9 accelerometer */
+	dragon_kxsd9_gpios: kxsd9-state {
+		pins = "gpio57"; /* IRQ line */
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	dragon_tma340_gpios: tma340-state {
+		reset-pins {
+			/* RESET line, TS_ATTN, WAKE_CTP */
+			pins = "gpio58";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-disable;
+		};
+		irq-pins {
+			pins = "gpio61"; /* IRQ line */
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&xoadc {
+	/* Reference voltage 2.2 V */
+	xoadc-ref-supply = <&pm8058_l18>;
+
+	/* Board-specific channels */
+	mpp5@5 {
+		/* Connected to AOUT of ALS sensor */
+		reg = <0x00 0x05>;
+	};
+	mpp6@6 {
+		/* Connected to test point TP43 */
+		reg = <0x00 0x06>;
+	};
+	mpp7@7 {
+		/* Connected to battery thermistor */
+		reg = <0x00 0x07>;
+	};
+	mpp8@8 {
+		/* Connected to battery ID detector */
+		reg = <0x00 0x08>;
+	};
+	mpp9@9 {
+		/* Connected to XO thermistor */
+		reg = <0x00 0x09>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
new file mode 100644
index 000000000000..c57c27cd8a20
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+/ {
+	model = "Asus Nexus7(flo)";
+	compatible = "asus,nexus7-flo", "qcom,apq8064";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@88d00000 {
+			compatible = "ramoops";
+			reg = <0x88d00000 0x100000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
+		};
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		regulator-type = "voltage";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	soc {
+		sram@2a03f000 {
+			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
+			reg = <0x2a03f000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-normal = <0x77665501>;
+				mode-bootloader = <0x77665500>;
+				mode-recovery = <0x77665502>;
+			};
+		};
+	};
+};
+
+&dsi0 {
+	vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+	vdd-supply = <&pm8921_l8>;
+	vddio-supply = <&pm8921_lvs7>;
+	avdd-supply = <&pm8921_l11>;
+	status = "okay";
+
+	panel@0 {
+		reg = <0>;
+		compatible = "jdi,lt070me05000";
+
+		vddp-supply = <&pm8921_l17>;
+		iovcc-supply = <&pm8921_lvs7>;
+
+		enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
+		dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_in {
+	remote-endpoint = <&mdp_dsi1_out>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+
+	bq27541@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+	};
+
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	clock-frequency = <200000>;
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	trackpad@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		interrupt-parent = <&tlmm_pinmux>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&mdp {
+	status = "okay";
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&mdp_dsi1_out {
+	remote-endpoint = <&dsi0_in>;
+};
+
+&rpm {
+	regulators {
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vin_lvs2-supply = <&pm8921_s1>;
+
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		vdd_ncp-supply = <&pm8921_l6>;
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		/* msm otg HSUSB_VDDCX */
+		s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		/*
+		 * msm_sdcc.1-sdc-vdd_io
+		 * tabla2x-slim-CDC_VDDA_RX
+		 * tabla2x-slim-CDC_VDDA_TX
+		 * tabla2x-slim-CDC_VDD_CP
+		 * tabla2x-slim-VDDIO_CDC
+		 */
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+			regulator-always-on;
+		};
+
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		/* mipi_dsi.1-dsi1_pll_vdda */
+		l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+		};
+
+		/* msm_otg-HSUSB_3p3 */
+		l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		/* msm_otg-HSUSB_1p8 */
+		l4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/* msm_sdcc.1-sdc_vdd */
+		l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		/* mipi_dsi.1-dsi1_avdd */
+		l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		/* pwm_power for backlight */
+		l17 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+
+		/* camera, qdsp6 */
+		l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * tabla2x-slim-CDC_VDDA_A_1P2V
+		 * tabla2x-slim-VDDD_CDC_D
+		 */
+		l25 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		lvs1 {
+			bias-pull-down;
+		};
+
+		lvs4 {
+			bias-pull-down;
+		};
+
+		lvs5 {
+			bias-pull-down;
+		};
+
+		lvs6 {
+			bias-pull-down;
+		};
+		/*
+		 * mipi_dsi.1-dsi1_vddio
+		 * pil_riva-pll_vdd
+		 */
+		lvs7 {
+			bias-pull-down;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
new file mode 100644
index 000000000000..d6ecfd8addb7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "CompuLab CM-QS600";
+	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	/* on board fixed 3.3v supply */
+	v3p3_fixed: regulator-v3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE V3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&pcie {
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&v3p3_fixed>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		lvs6 {
+			bias-pull-down;
+		};
+
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&v3p3_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	status = "okay";
+	vmmc-supply = <&v3p3_fixed>;
+	vqmmc-supply = <&v3p3_fixed>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
new file mode 100644
index 000000000000..96307550523a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Qualcomm APQ8064/IFC6410";
+	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+		i2c0 = &gsbi1_i2c;
+		i2c1 = &gsbi2_i2c;
+		i2c2 = &gsbi3_i2c;
+		i2c3 = &gsbi4_i2c;
+		spi0 = &gsbi5_spi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&notify_led>;
+
+		led-user1 {
+			label = "apq8064:green:user1";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		regulator-type = "voltage";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	status = "okay";
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+/* CAM I2C MIPI-CSI connector */
+&gsbi4_i2c {
+	status = "okay";
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+};
+
+&gsbi5_spi {
+	num-cs = <1>;
+	cs-gpios = <&tlmm_pinmux 53 0>;
+	status = "okay";
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&hdmi {
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+	hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&hdmi_in {
+	remote-endpoint = <&mdp_dtv_out>;
+};
+
+&hdmi_out {
+	remote-endpoint = <&hdmi_con>;
+};
+
+&hdmi_phy {
+	status = "okay";
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dtv_out {
+	remote-endpoint = <&hdmi_in>;
+};
+
+&pcie {
+	status = "okay";
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&ext_3p3v>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+
+	notify_led: nled-state {
+		pinconf {
+			pins = "gpio18";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		lvs1 {
+			bias-pull-down;
+		};
+
+		lvs6 {
+			bias-pull-down;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata0 {
+	target-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	vmmc-supply = <&ext_3p3v>;
+	vqmmc-supply = <&pm8921_lvs1>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	card_detect: card_detect {
+		mux {
+			pins = "gpio26";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	pcie_pins: pcie_pinmux {
+		mux {
+			pins = "gpio27";
+			function = "gpio";
+		};
+		conf {
+			pins = "gpio27";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
new file mode 100644
index 000000000000..b4d286a6fab1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&tlmm_pinmux {
+	sdc4_gpios: sdc4-gpios {
+		pios {
+			pins = "gpio63", "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
+			function = "sdc4";
+		};
+	};
+
+	sdcc1_pins: sdcc1-pin-active {
+		clk {
+			pins = "sdc1_clk";
+			drive-strengh = <16>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "sdc1_cmd";
+			drive-strengh = <10>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "sdc1_data";
+			drive-strengh = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdcc3_pins: sdcc3-pin-active {
+		clk {
+			pins = "sdc3_clk";
+			drive-strengh = <8>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "sdc3_cmd";
+			drive-strengh = <8>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "sdc3_data";
+			drive-strengh = <8>;
+			bias-pull-up;
+		};
+	};
+
+	ps_hold: ps_hold {
+		mux {
+			pins = "gpio78";
+			function = "ps_hold";
+		};
+	};
+
+	i2c1_pins: i2c1 {
+		mux {
+			pins = "gpio20", "gpio21";
+			function = "gsbi1";
+		};
+
+		pinconf {
+			pins = "gpio20", "gpio21";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c1_pins_sleep: i2c1_pins_sleep {
+		mux {
+			pins = "gpio20", "gpio21";
+			function = "gpio";
+		};
+		pinconf {
+			pins = "gpio20", "gpio21";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	gsbi1_uart_2pins: gsbi1_uart_2pins {
+		mux {
+			pins = "gpio18", "gpio19";
+			function = "gsbi1";
+		};
+	};
+
+	gsbi1_uart_4pins: gsbi1_uart_4pins {
+		mux {
+			pins = "gpio18", "gpio19", "gpio20", "gpio21";
+			function = "gsbi1";
+		};
+	};
+
+	i2c2_pins: i2c2 {
+		mux {
+			pins = "gpio24", "gpio25";
+			function = "gsbi2";
+		};
+
+		pinconf {
+			pins = "gpio24", "gpio25";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c2_pins_sleep: i2c2_pins_sleep {
+		mux {
+			pins = "gpio24", "gpio25";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio24", "gpio25";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	i2c3_pins: i2c3 {
+		mux {
+			pins = "gpio8", "gpio9";
+			function = "gsbi3";
+		};
+
+		pinconf {
+			pins = "gpio8", "gpio9";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c3_pins_sleep: i2c3_pins_sleep {
+		mux {
+			pins = "gpio8", "gpio9";
+			function = "gpio";
+		};
+		pinconf {
+			pins = "gpio8", "gpio9";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	i2c4_pins: i2c4 {
+		mux {
+			pins = "gpio12", "gpio13";
+			function = "gsbi4";
+		};
+
+		pinconf {
+			pins = "gpio12", "gpio13";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c4_pins_sleep: i2c4_pins_sleep {
+		mux {
+			pins = "gpio12", "gpio13";
+			function = "gpio";
+		};
+		pinconf {
+			pins = "gpio12", "gpio13";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	spi5_default: spi5_default {
+		pinmux {
+			pins = "gpio51", "gpio52", "gpio54";
+			function = "gsbi5";
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio53";
+		};
+
+		pinconf {
+			pins = "gpio51", "gpio52", "gpio54";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		pinconf_cs {
+			pins = "gpio53";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	spi5_sleep: spi5_sleep {
+		pinmux {
+			function = "gpio";
+			pins = "gpio51", "gpio52", "gpio53", "gpio54";
+		};
+
+		pinconf {
+			pins = "gpio51", "gpio52", "gpio53", "gpio54";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	i2c6_pins: i2c6 {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "gsbi6";
+		};
+
+		pinconf {
+			pins = "gpio16", "gpio17";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c6_pins_sleep: i2c6_pins_sleep {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "gpio";
+		};
+		pinconf {
+			pins = "gpio16", "gpio17";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	gsbi6_uart_2pins: gsbi6_uart_2pins {
+		mux {
+			pins = "gpio14", "gpio15";
+			function = "gsbi6";
+		};
+	};
+
+	gsbi6_uart_4pins: gsbi6_uart_4pins {
+		mux {
+			pins = "gpio14", "gpio15", "gpio16", "gpio17";
+			function = "gsbi6";
+		};
+	};
+
+	gsbi7_uart_2pins: gsbi7_uart_2pins {
+		mux {
+			pins = "gpio82", "gpio83";
+			function = "gsbi7";
+		};
+	};
+
+	gsbi7_uart_4pins: gsbi7_uart_4pins {
+		mux {
+			pins = "gpio82", "gpio83", "gpio84", "gpio85";
+			function = "gsbi7";
+		};
+	};
+
+	i2c7_pins: i2c7 {
+		mux {
+			pins = "gpio84", "gpio85";
+			function = "gsbi7";
+		};
+
+		pinconf {
+			pins = "gpio84", "gpio85";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	i2c7_pins_sleep: i2c7_pins_sleep {
+		mux {
+			pins = "gpio84", "gpio85";
+			function = "gpio";
+		};
+		pinconf {
+			pins = "gpio84", "gpio85";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	riva_fm_pin_a: riva-fm-active {
+		pins = "gpio14", "gpio15";
+		function = "riva_fm";
+	};
+
+	riva_bt_pin_a: riva-bt-active {
+		pins = "gpio16", "gpio17";
+		function = "riva_bt";
+	};
+
+	riva_wlan_pin_a: riva-wlan-active {
+		pins = "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
+		function = "riva_wlan";
+
+		drive-strength = <6>;
+		bias-pull-down;
+	};
+
+	hdmi_pinctrl: hdmi-pinctrl {
+		mux {
+			pins = "gpio70", "gpio71", "gpio72";
+			function = "hdmi";
+		};
+
+		pinconf_ddc {
+			pins = "gpio70", "gpio71";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		pinconf_hpd {
+			pins = "gpio72";
+			bias-pull-down;
+			drive-strength = <16>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
new file mode 100644
index 000000000000..9244512b74d1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Sony Xperia Z";
+	compatible = "sony,xperia-yuga", "qcom,apq8064";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi5_uart_pin_a>;
+	status = "okay";
+};
+
+&pm8921_gpio {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio3", "gpio4", "gpio29", "gpio35";
+		function = "normal";
+
+		bias-pull-up;
+		drive-push-pull;
+		input-enable;
+		power-source = <2>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		qcom,pull-up-strength = <0>;
+	};
+};
+
+&riva {
+	pinctrl-names = "default";
+	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+	status = "okay";
+};
+
+&rpm {
+	regulators {
+		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs_1_3_6-supply = <&pm8921_s4>;
+		vin_lvs_4_5_7-supply = <&pm8921_s4>;
+		vin_ncp-supply = <&pm8921_l6>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_l24-supply = <&pm8921_s1>;
+		vin_l25-supply = <&pm8921_s1>;
+		vin_l27-supply = <&pm8921_s7>;
+		vin_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		s8 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+
+		/* PMOS LDO */
+		l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			bias-pull-down;
+		};
+
+		l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l10 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		l17 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		l21 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		l22 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		l27 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		l28 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		l29 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		lvs1 {
+			bias-pull-down;
+		};
+
+		lvs2 {
+			bias-pull-down;
+		};
+
+		lvs3 {
+			bias-pull-down;
+		};
+
+		lvs4 {
+			bias-pull-down;
+		};
+
+		lvs5 {
+			bias-pull-down;
+		};
+
+		lvs6 {
+			bias-pull-down;
+		};
+
+		lvs7 {
+			bias-pull-down;
+		};
+
+		usb-switch {};
+
+		hdmi-switch {};
+
+		ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
+
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	gsbi5_uart_pin_a: gsbi5-uart-pin-active {
+		rx {
+			pins = "gpio52";
+			function = "gsbi5";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		tx {
+			pins = "gpio51";
+			function = "gsbi5";
+			drive-strength = <4>;
+			bias-disable;
+		};
+	};
+
+
+	sdcc3_cd_pin_a: sdcc3-cd-pin-active {
+		pins = "gpio26";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
new file mode 100644
index 000000000000..46ed48f0244f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
new file mode 100644
index 000000000000..d2289205ff81
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -0,0 +1,1896 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm APQ8064";
+	compatible = "qcom,apq8064";
+	interrupt-parent = <&intc>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		smem_region: smem@80000000 {
+			reg = <0x80000000 0x200000>;
+			no-map;
+		};
+
+		wcnss_mem: wcnss@8f000000 {
+			reg = <0x8f000000 0x700000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU1: cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU2: cpu@2 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU3: cpu@3 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc",
+						"arm,idle-state";
+				entry-latency-us = <400>;
+				exit-latency-us = <900>;
+				min-residency-us = <3000>;
+			};
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+			coefficients = <1199 0>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+			coefficients = <1132 0>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+			coefficients = <1199 0>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 10>;
+			coefficients = <1132 0>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <1 10 0x304>;
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		pxo_board: pxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	sfpb_mutex: hwmutex {
+		compatible = "qcom,sfpb-mutex";
+		syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
+		#hwlock-cells = <1>;
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_region>;
+
+		hwlocks = <&sfpb_mutex 3>;
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		modem-edge {
+			interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
+
+			qcom,ipc = <&l2cc 8 3>;
+			qcom,smd-edge = <0>;
+
+			status = "disabled";
+		};
+
+		q6-edge {
+			interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
+
+			qcom,ipc = <&l2cc 8 15>;
+			qcom,smd-edge = <1>;
+
+			status = "disabled";
+		};
+
+		dsps-edge {
+			interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
+
+			qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
+			qcom,smd-edge = <3>;
+
+			status = "disabled";
+		};
+
+		riva-edge {
+			interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
+
+			qcom,ipc = <&l2cc 8 25>;
+			qcom,smd-edge = <6>;
+
+			status = "disabled";
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&l2cc 8 4>;
+		qcom,ipc-2 = <&l2cc 8 14>;
+		qcom,ipc-3 = <&l2cc 8 23>;
+		qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smsm: modem@1 {
+			reg = <1>;
+			interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		q6_smsm: q6@2 {
+			reg = <2>;
+			interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@3 {
+			reg = <3>;
+			interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		dsps_smsm: dsps@4 {
+			reg = <4>;
+			interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-apq8064", "qcom,scm";
+
+			clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
+			clock-names = "core";
+		};
+	};
+
+
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&xoadc 0x00 0x01>, /* Battery */
+			    <&xoadc 0x00 0x02>, /* DC in (charger) */
+			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
+			    <&xoadc 0x00 0x0b>, /* Die temperature */
+			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			    <&xoadc 0x00 0x0e>; /* Charger temperature */
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		tlmm_pinmux: pinctrl@800000 {
+			compatible = "qcom,apq8064-pinctrl";
+			reg = <0x800000 0x4000>;
+
+			gpio-controller;
+			gpio-ranges = <&tlmm_pinmux 0 0 90>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&ps_hold>;
+		};
+
+		sfpb_wrapper_mutex: syscon@1200000 {
+			compatible = "syscon";
+			reg = <0x01200000 0x8000>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-apq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <1 1 0x301>,
+				     <1 2 0x301>,
+				     <1 3 0x301>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			cpu-offset = <0x80000>;
+		};
+
+		acc0: clock-controller@2088000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		acc1: clock-controller@2098000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
+		};
+
+		acc2: clock-controller@20a8000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu2_aux";
+			#clock-cells = <0>;
+		};
+
+		acc3: clock-controller@20b8000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu3_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: power-controller@2089000 {
+			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		saw1: power-controller@2099000 {
+			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		saw2: power-controller@20a9000 {
+			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
+			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		saw3: power-controller@20b9000 {
+			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
+			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		sps_sic_non_secure: sps-sic-non-secure@12100000 {
+			compatible = "syscon";
+			reg = <0x12100000 0x10000>;
+		};
+
+		gsbi1: gsbi@12440000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <1>;
+			reg = <0x12440000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi1_serial: serial@12450000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12450000 0x100>,
+				      <0x12400000 0x03>;
+				interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi1_i2c: i2c@12460000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-1 = <&i2c1_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				reg = <0x12460000 0x1000>;
+				interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+		};
+
+		gsbi2: gsbi@12480000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x12480000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi2_i2c: i2c@124a0000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x124a0000 0x1000>;
+				pinctrl-0 = <&i2c2_pins>;
+				pinctrl-1 = <&i2c2_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <3>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				pinctrl-0 = <&i2c3_pins>;
+				pinctrl-1 = <&i2c3_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>,
+					 <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x03>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi4_i2c: i2c@16380000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				pinctrl-0 = <&i2c4_pins>;
+				pinctrl-1 = <&i2c4_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				reg = <0x16380000 0x1000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_QUP_CLK>,
+					 <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi5: gsbi@1a200000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x1a200000 0x03>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi5_serial: serial@1a240000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x1a240000 0x100>,
+				      <0x1a200000 0x03>;
+				interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi5_spi: spi@1a280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&spi5_default>;
+				pinctrl-1 = <&spi5_sleep>;
+				pinctrl-names = "default", "sleep";
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gsbi6: gsbi@16500000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <6>;
+			reg = <0x16500000 0x03>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi6_serial: serial@16540000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16540000 0x100>,
+				      <0x16500000 0x03>;
+				interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				pinctrl-0 = <&i2c6_pins>;
+				pinctrl-1 = <&i2c6_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI6_QUP_CLK>,
+					 <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <0 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				pinctrl-0 = <&i2c7_pins>;
+				pinctrl-1 = <&i2c7_pins_sleep>;
+				pinctrl-names = "default", "sleep";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_QUP_CLK>,
+					 <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
+		ssbi@c00000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00c00000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+
+			pm8821: pmic {
+				compatible = "qcom,pm8821";
+				interrupt-parent = <&tlmm_pinmux>;
+				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pm8821_mpps: mpps@50 {
+					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
+					reg = <0x50>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pm8821_mpps 0 0 4>;
+				};
+			};
+		};
+
+		ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+
+			pmicintc: pmic {
+				compatible = "qcom,pm8921";
+				interrupt-parent = <&tlmm_pinmux>;
+				interrupts = <74 8>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pm8921_gpio: gpio@150 {
+
+					compatible = "qcom,pm8921-gpio",
+						     "qcom,ssbi-gpio";
+					reg = <0x150>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					gpio-ranges = <&pm8921_gpio 0 0 44>;
+					#gpio-cells = <2>;
+
+				};
+
+				pm8921_mpps: mpps@50 {
+					compatible = "qcom,pm8921-mpp",
+						     "qcom,ssbi-mpp";
+					reg = <0x50>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pm8921_mpps 0 0 12>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				rtc@11d {
+					compatible = "qcom,pm8921-rtc";
+					interrupt-parent = <&pmicintc>;
+					interrupts = <39 1>;
+					reg = <0x11d>;
+					allow-set-time;
+				};
+
+				pwrkey@1c {
+					compatible = "qcom,pm8921-pwrkey";
+					reg = <0x1c>;
+					interrupt-parent = <&pmicintc>;
+					interrupts = <50 1>, <51 1>;
+					debounce = <15625>;
+					pull-up;
+				};
+
+				xoadc: xoadc@197 {
+					compatible = "qcom,pm8921-adc";
+					reg = <197>;
+					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+					#io-channel-cells = <2>;
+
+					vcoin: adc-channel@0 {
+						reg = <0x00 0x00>;
+					};
+					vbat: adc-channel@1 {
+						reg = <0x00 0x01>;
+					};
+					dcin: adc-channel@2 {
+						reg = <0x00 0x02>;
+					};
+					vph_pwr: adc-channel@4 {
+						reg = <0x00 0x04>;
+					};
+					batt_therm: adc-channel@8 {
+						reg = <0x00 0x08>;
+					};
+					batt_id: adc-channel@9 {
+						reg = <0x00 0x09>;
+					};
+					usb_vbus: adc-channel@a {
+						reg = <0x00 0x0a>;
+					};
+					die_temp: adc-channel@b {
+						reg = <0x00 0x0b>;
+					};
+					ref_625mv: adc-channel@c {
+						reg = <0x00 0x0c>;
+					};
+					ref_1250mv: adc-channel@d {
+						reg = <0x00 0x0d>;
+					};
+					chg_temp: adc-channel@e {
+						reg = <0x00 0x0e>;
+					};
+					ref_muxoff: adc-channel@f {
+						reg = <0x00 0x0f>;
+					};
+				};
+			};
+		};
+
+		qfprom: qfprom@700000 {
+			compatible = "qcom,apq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			tsens_calib: calib@404 {
+				reg = <0x404 0x10>;
+			};
+			tsens_backup: backup_calib@414 {
+				reg = <0x414 0x10>;
+			};
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-apq8064", "syscon";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+
+			tsens: thermal-sensor {
+				compatible = "qcom,msm8960-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-apq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
+		};
+
+		mmcc: clock-controller@4000000 {
+			compatible = "qcom,mmcc-apq8064";
+			reg = <0x4000000 0x1000>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <&dsi0_phy 1>,
+				 <&dsi0_phy 0>,
+				 <&dsi1_phy 1>,
+				 <&dsi1_phy 0>,
+				 <&hdmi_phy>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-apq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
+				#clock-cells = <1>;
+				clocks = <&pxo_board>, <&cxo_board>;
+				clock-names = "pxo", "cxo";
+			};
+
+			regulators {
+				compatible = "qcom,rpm-pm8921-regulators";
+
+				pm8921_s1: s1 {};
+				pm8921_s2: s2 {};
+				pm8921_s3: s3 {};
+				pm8921_s4: s4 {};
+				pm8921_s7: s7 {};
+				pm8921_s8: s8 {};
+
+				pm8921_l1: l1 {};
+				pm8921_l2: l2 {};
+				pm8921_l3: l3 {};
+				pm8921_l4: l4 {};
+				pm8921_l5: l5 {};
+				pm8921_l6: l6 {};
+				pm8921_l7: l7 {};
+				pm8921_l8: l8 {};
+				pm8921_l9: l9 {};
+				pm8921_l10: l10 {};
+				pm8921_l11: l11 {};
+				pm8921_l12: l12 {};
+				pm8921_l14: l14 {};
+				pm8921_l15: l15 {};
+				pm8921_l16: l16 {};
+				pm8921_l17: l17 {};
+				pm8921_l18: l18 {};
+				pm8921_l21: l21 {};
+				pm8921_l22: l22 {};
+				pm8921_l23: l23 {};
+				pm8921_l24: l24 {};
+				pm8921_l25: l25 {};
+				pm8921_l26: l26 {};
+				pm8921_l27: l27 {};
+				pm8921_l28: l28 {};
+				pm8921_l29: l29 {};
+
+				pm8921_lvs1: lvs1 {};
+				pm8921_lvs2: lvs2 {};
+				pm8921_lvs3: lvs3 {};
+				pm8921_lvs4: lvs4 {};
+				pm8921_lvs5: lvs5 {};
+				pm8921_lvs6: lvs6 {};
+				pm8921_lvs7: lvs7 {};
+
+				pm8921_usb_switch: usb-switch {};
+
+				pm8921_hdmi_switch: hdmi-switch {
+					bias-pull-down;
+				};
+
+				pm8921_ncp: ncp {};
+			};
+		};
+
+		usb1: usb@12500000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+					#phy-cells = <0>;
+				};
+			};
+		};
+
+		usb3: usb@12520000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12520000 0x200>,
+			      <0x12520200 0x200>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS3_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs3_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs3_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb3 0>;
+					reset-names = "por";
+				};
+			};
+		};
+
+		usb4: usb@12530000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12530000 0x200>,
+			      <0x12530200 0x200>;
+			interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS4_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs4_phy>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs4_phy: phy {
+					compatible = "qcom,usb-hs-phy-apq8064",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb4 0>;
+					reset-names = "por";
+				};
+			};
+		};
+
+		sata_phy0: phy@1b400000 {
+			compatible = "qcom,apq8064-sata-phy";
+			status = "disabled";
+			reg = <0x1b400000 0x200>;
+			reg-names = "phy_mem";
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+			#phy-cells = <0>;
+		};
+
+		sata0: sata@29000000 {
+			compatible = "qcom,apq8064-ahci", "generic-ahci";
+			status	 = "disabled";
+			reg	 = <0x29000000 0x180>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_iface",
+				      "iface",
+				      "bus",
+				      "rxoob",
+				      "core_pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>,
+					  <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy0>;
+			phy-names = "sata-phy";
+			ports-implemented = <0x1>;
+		};
+
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc4: mmc@121c0000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x121c0000 0x2000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdc4_gpios>;
+		};
+
+		sdcc4bam: dma-controller@121c2000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x121c2000 0x8000>;
+			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC4_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdcc1_pins>;
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-apq8064", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		gpu: adreno-3xx@4300000 {
+			compatible = "qcom,adreno-320.2", "qcom,adreno";
+			reg = <0x04300000 0x20000>;
+			reg-names = "kgsl_3d0_reg_memory";
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+			clock-names =
+			    "core",
+			    "iface",
+			    "mem",
+			    "mem_iface";
+			clocks =
+			    <&mmcc GFX3D_CLK>,
+			    <&mmcc GFX3D_AHB_CLK>,
+			    <&mmcc GFX3D_AXI_CLK>,
+			    <&mmcc MMSS_IMEM_AHB_CLK>;
+
+			iommus = <&gfx3d 0
+				  &gfx3d 1
+				  &gfx3d 2
+				  &gfx3d 3
+				  &gfx3d 4
+				  &gfx3d 5
+				  &gfx3d 6
+				  &gfx3d 7
+				  &gfx3d 8
+				  &gfx3d 9
+				  &gfx3d 10
+				  &gfx3d 11
+				  &gfx3d 12
+				  &gfx3d 13
+				  &gfx3d 14
+				  &gfx3d 15
+				  &gfx3d 16
+				  &gfx3d 17
+				  &gfx3d 18
+				  &gfx3d 19
+				  &gfx3d 20
+				  &gfx3d 21
+				  &gfx3d 22
+				  &gfx3d 23
+				  &gfx3d 24
+				  &gfx3d 25
+				  &gfx3d 26
+				  &gfx3d 27
+				  &gfx3d 28
+				  &gfx3d 29
+				  &gfx3d 30
+				  &gfx3d 31
+				  &gfx3d1 0
+				  &gfx3d1 1
+				  &gfx3d1 2
+				  &gfx3d1 3
+				  &gfx3d1 4
+				  &gfx3d1 5
+				  &gfx3d1 6
+				  &gfx3d1 7
+				  &gfx3d1 8
+				  &gfx3d1 9
+				  &gfx3d1 10
+				  &gfx3d1 11
+				  &gfx3d1 12
+				  &gfx3d1 13
+				  &gfx3d1 14
+				  &gfx3d1 15
+				  &gfx3d1 16
+				  &gfx3d1 17
+				  &gfx3d1 18
+				  &gfx3d1 19
+				  &gfx3d1 20
+				  &gfx3d1 21
+				  &gfx3d1 22
+				  &gfx3d1 23
+				  &gfx3d1 24
+				  &gfx3d1 25
+				  &gfx3d1 26
+				  &gfx3d1 27
+				  &gfx3d1 28
+				  &gfx3d1 29
+				  &gfx3d1 30
+				  &gfx3d1 31>;
+
+			operating-points-v2 = <&gpu_opp_table>;
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
+				};
+
+				opp-27000000 {
+					opp-hz = /bits/ 64 <27000000>;
+				};
+			};
+		};
+
+		mmss_sfpb: syscon@5700000 {
+			compatible = "syscon";
+			reg = <0x5700000 0x70>;
+		};
+
+		dsi0: dsi@4700000 {
+			compatible = "qcom,apq8064-dsi-ctrl",
+				     "qcom,mdss-dsi-ctrl";
+			label = "MDSS DSI CTRL->0";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x04700000 0x200>;
+			reg-names = "dsi_ctrl";
+
+			clocks = <&mmcc DSI_M_AHB_CLK>,
+				<&mmcc DSI_S_AHB_CLK>,
+				<&mmcc AMP_AHB_CLK>,
+				<&mmcc DSI_CLK>,
+				<&mmcc DSI1_BYTE_CLK>,
+				<&mmcc DSI_PIXEL_CLK>,
+				<&mmcc DSI1_ESC_CLK>;
+			clock-names = "iface", "bus", "core_mmss",
+					"src", "byte", "pixel",
+					"core";
+
+			assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
+					<&mmcc DSI1_ESC_SRC>,
+					<&mmcc DSI_SRC>,
+					<&mmcc DSI_PIXEL_SRC>;
+			assigned-clock-parents = <&dsi0_phy 0>,
+						<&dsi0_phy 0>,
+						<&dsi0_phy 1>,
+						<&dsi0_phy 1>;
+			syscon-sfpb = <&mmss_sfpb>;
+			phys = <&dsi0_phy>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi0_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi0_out: endpoint {
+					};
+				};
+			};
+		};
+
+
+		dsi0_phy: phy@4700200 {
+			compatible = "qcom,dsi-phy-28nm-8960";
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			reg = <0x04700200 0x100>,
+				<0x04700300 0x200>,
+				<0x04700500 0x5c>;
+			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
+			clock-names = "iface", "ref";
+			clocks = <&mmcc DSI_M_AHB_CLK>,
+				 <&pxo_board>;
+			status = "disabled";
+		};
+
+		dsi1: dsi@5800000 {
+			compatible = "qcom,mdss-dsi-ctrl";
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x05800000 0x200>;
+			reg-names = "dsi_ctrl";
+
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&mmcc DSI2_S_AHB_CLK>,
+				 <&mmcc AMP_AHB_CLK>,
+				 <&mmcc DSI2_CLK>,
+				 <&mmcc DSI2_BYTE_CLK>,
+				 <&mmcc DSI2_PIXEL_CLK>,
+				 <&mmcc DSI2_ESC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "core_mmss",
+				      "src",
+				      "byte",
+				      "pixel",
+				      "core";
+
+			assigned-clocks = <&mmcc DSI2_BYTE_SRC>,
+					  <&mmcc DSI2_ESC_SRC>,
+					  <&mmcc DSI2_SRC>,
+					  <&mmcc DSI2_PIXEL_SRC>;
+			assigned-clock-parents = <&dsi1_phy 0>,
+						 <&dsi1_phy 0>,
+						 <&dsi1_phy 1>,
+						 <&dsi1_phy 1>;
+
+			syscon-sfpb = <&mmss_sfpb>;
+			phys = <&dsi1_phy>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi1_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi1_out: endpoint {
+					};
+				};
+			};
+		};
+
+
+		dsi1_phy: dsi-phy@5800200 {
+			compatible = "qcom,dsi-phy-28nm-8960";
+			reg = <0x05800200 0x100>,
+			      <0x05800300 0x200>,
+			      <0x05800500 0x5c>;
+			reg-names = "dsi_pll",
+				    "dsi_phy",
+				    "dsi_phy_regulator";
+			clock-names = "iface",
+				      "ref";
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&pxo_board>;
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mdp_port0: iommu@7500000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "iommu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc MDP_AXI_CLK>;
+			reg = <0x07500000 0x100000>;
+			interrupts =
+			    <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+			    <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ncb = <2>;
+		};
+
+		mdp_port1: iommu@7600000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "iommu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc MDP_AXI_CLK>;
+			reg = <0x07600000 0x100000>;
+			interrupts =
+			    <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+			    <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ncb = <2>;
+		};
+
+		gfx3d: iommu@7c00000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "iommu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc GFX3D_AXI_CLK>;
+			reg = <0x07c00000 0x100000>;
+			interrupts =
+			    <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+			    <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ncb = <3>;
+		};
+
+		gfx3d1: iommu@7d00000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "iommu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc GFX3D_AXI_CLK>;
+			reg = <0x07d00000 0x100000>;
+			interrupts =
+			    <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+			    <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ncb = <3>;
+		};
+
+		pcie: pci@1b500000 {
+			compatible = "qcom,pcie-apq8064";
+			reg = <0x1b500000 0x1000>,
+			      <0x1b502000 0x80>,
+			      <0x1b600000 0x100>,
+			      <0x0ff00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00100000>, /* I/O */
+				 <0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* mem */
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			clocks = <&gcc PCIE_A_CLK>,
+				 <&gcc PCIE_H_CLK>,
+				 <&gcc PCIE_PHY_REF_CLK>;
+			clock-names = "core", "iface", "phy";
+			resets = <&gcc PCIE_ACLK_RESET>,
+				 <&gcc PCIE_HCLK_RESET>,
+				 <&gcc PCIE_POR_RESET>,
+				 <&gcc PCIE_PCI_RESET>,
+				 <&gcc PCIE_PHY_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy";
+			status = "disabled";
+		};
+
+		hdmi: hdmi-tx@4a00000 {
+			compatible = "qcom,hdmi-tx-8960";
+			pinctrl-names = "default";
+			pinctrl-0 = <&hdmi_pinctrl>;
+			reg = <0x04a00000 0x2f0>;
+			reg-names = "core_physical";
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mmcc HDMI_APP_CLK>,
+				 <&mmcc HDMI_M_AHB_CLK>,
+				 <&mmcc HDMI_S_AHB_CLK>;
+			clock-names = "core",
+				      "master_iface",
+				      "slave_iface";
+
+			phys = <&hdmi_phy>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					hdmi_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					hdmi_out: endpoint {
+					};
+				};
+			};
+		};
+
+		hdmi_phy: phy@4a00400 {
+			compatible = "qcom,hdmi-phy-8960";
+			reg = <0x4a00400 0x60>,
+			      <0x4a00500 0x100>;
+			reg-names = "hdmi_phy",
+				    "hdmi_pll";
+
+			clocks = <&mmcc HDMI_S_AHB_CLK>;
+			clock-names = "slave_iface";
+			#phy-cells = <0>;
+			#clock-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mdp: display-controller@5100000 {
+			compatible = "qcom,mdp4";
+			reg = <0x05100000 0xf0000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&mmcc MDP_CLK>,
+				 <&mmcc MDP_AHB_CLK>,
+				 <&mmcc MDP_AXI_CLK>,
+				 <&mmcc MDP_LUT_CLK>,
+				 <&mmcc HDMI_TV_CLK>,
+				 <&mmcc MDP_TV_CLK>;
+			clock-names = "core_clk",
+				      "iface_clk",
+				      "bus_clk",
+				      "lut_clk",
+				      "hdmi_clk",
+				      "tv_clk";
+
+			iommus = <&mdp_port0 0
+				  &mdp_port0 2
+				  &mdp_port1 0
+				  &mdp_port1 2>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					mdp_lvds_out: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					mdp_dsi1_out: endpoint {
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					mdp_dsi2_out: endpoint {
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					mdp_dtv_out: endpoint {
+					};
+				};
+			};
+		};
+
+		riva: riva-pil@3200800 {
+			compatible = "qcom,riva-pil";
+
+			reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal";
+
+			memory-region = <&wcnss_mem>;
+
+			vddcx-supply = <&pm8921_s3>;
+			vddmx-supply = <&pm8921_l24>;
+			vddpx-supply = <&pm8921_s4>;
+
+			status = "disabled";
+
+			iris {
+				compatible = "qcom,wcn3660";
+
+				clocks = <&cxo_board>;
+				clock-names = "xo";
+
+				vddxo-supply = <&pm8921_l4>;
+				vddrfa-supply = <&pm8921_s2>;
+				vddpa-supply = <&pm8921_l10>;
+				vdddig-supply = <&pm8921_lvs2>;
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&l2cc 8 25>;
+				qcom,smd-edge = <6>;
+
+				label = "riva";
+
+				wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+
+					qcom,mmio = <&riva>;
+
+					bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+							     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		etb@1a01000 {
+			compatible = "arm,coresight-etb10", "arm,primecell";
+			reg = <0x1a01000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			in-ports {
+				port {
+					etb_in: endpoint {
+						remote-endpoint = <&replicator_out0>;
+					};
+				};
+			};
+		};
+
+		tpiu@1a03000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0x1a03000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			in-ports {
+				port {
+					tpiu_in: endpoint {
+						remote-endpoint = <&replicator_out1>;
+					};
+				};
+			};
+		};
+
+		replicator {
+			compatible = "arm,coresight-static-replicator";
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			out-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint = <&etb_in>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint = <&tpiu_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&funnel_out>;
+					};
+				};
+			};
+		};
+
+		funnel@1a04000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0x1a04000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 2 - connected to STM component
+				 * 3 - not-connected
+				 * 6 - not-connected
+				 * 7 - not-connected
+				 */
+				port@0 {
+					reg = <0>;
+					funnel_in0: endpoint {
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					funnel_in1: endpoint {
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+				port@4 {
+					reg = <4>;
+					funnel_in4: endpoint {
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+				port@5 {
+					reg = <5>;
+					funnel_in5: endpoint {
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					funnel_out: endpoint {
+						remote-endpoint = <&replicator_in>;
+					};
+				};
+			};
+		};
+
+		etm@1a1c000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x1a1c000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU0>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint = <&funnel_in0>;
+					};
+				};
+			};
+		};
+
+		etm@1a1d000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x1a1d000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU1>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint = <&funnel_in1>;
+					};
+				};
+			};
+		};
+
+		etm@1a1e000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x1a1e000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU2>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint = <&funnel_in4>;
+					};
+				};
+			};
+		};
+
+		etm@1a1f000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x1a1f000 0x1000>;
+
+			clocks = <&rpmcc RPM_QDSS_CLK>;
+			clock-names = "apb_pclk";
+
+			cpu = <&CPU3>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint = <&funnel_in5>;
+					};
+				};
+			};
+		};
+	};
+};
+#include "qcom-apq8064-pins.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
new file mode 100644
index 000000000000..e0679436000b
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8974.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+
+/delete-node/ &mpss_region;
+
+/ {
+	model = "Qualcomm APQ8074 Dragonboard";
+	compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8941_0;
+		usid4 = &pm8841_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-0 = <&msm_keys_default>;
+		pinctrl-names = "default";
+
+		button-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-general {
+			label = "General";
+			linux,code = <KEY_PROG1>;
+			gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reserved-memory {
+		mpss_region: mpss@ac00000 {
+			reg = <0x0ac00000 0x2500000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <200000>;
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+		read-only;
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_l22>;
+	vddio-supply = <&pm8941_l12>;
+
+	status = "okay";
+
+	panel: panel@0 {
+		compatible = "sharp,ls043t1le01-qhd";
+		reg = <0>;
+
+		avdd-supply = <&pm8941_l22>;
+		backlight = <&pm8941_wled>;
+		reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&pm8941_gpios {
+        msm_keys_default: pm8941-gpio-keys-state {
+		pins = "gpio5", "gpio23";
+		function = "normal";
+		input-enable;
+		drive-push-pull;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		power-source = <PM8941_GPIO_S3>; /* 1.8V */
+        };
+};
+
+&pm8941_lpg {
+	qcom,power-source = <1>;
+	status = "okay";
+
+	led@5 {
+		reg = <5>;
+		color = <LED_COLOR_ID_BLUE>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@6 {
+		reg = <6>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@7 {
+		reg = <7>;
+		color = <LED_COLOR_ID_RED>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+};
+
+&pm8941_wled {
+	qcom,cs-out;
+	qcom,switching-freq = <3200>;
+	qcom,ovp = <32>;
+	qcom,num-strings = <1>;
+
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	firmware-name = "qcom/apq8074/adsp.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+
+	firmware-name = "qcom/apq8074/mba.mbn", "qcom/apq8074/modem.mbn";
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vin_5vs-supply = <&pm8941_5v>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs2_phy>;
+	phy-select = <&tcsr 0xb000 1>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs2_phy {
+	status = "okay";
+	v3p3-supply = <&pm8941_l24>;
+	v1p8-supply = <&pm8941_l6>;
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x63>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
new file mode 100644
index 000000000000..116e59a3b76d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8084.dtsi"
+#include "qcom-pma8084.dtsi"
+
+/ {
+	model = "Qualcomm APQ8084/IFC6540";
+	compatible = "qcom,apq8084-sbc", "qcom,apq8084";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+		usid0 = &pma8084_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		serial@f995e000 {
+			status = "okay";
+		};
+	};
+};
+
+&sdhc_1 {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
new file mode 100644
index 000000000000..c6b6680248a6
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8084.dtsi"
+#include "qcom-pma8084.dtsi"
+
+/ {
+	model = "Qualcomm APQ 8084-MTP";
+	compatible = "qcom,apq8084-mtp", "qcom,apq8084";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+		usid0 = &pma8084_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		serial@f995e000 {
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
new file mode 100644
index 000000000000..8f178bc87e1d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
@@ -0,0 +1,853 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-apq8084.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm APQ 8084";
+	compatible = "qcom,apq8084";
+	interrupt-parent = <&intc>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		smem_mem: smem_region@fa00000 {
+			reg = <0xfa00000 0x200000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,krait";
+			reg = <0>;
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "qcom,krait";
+			reg = <1>;
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "qcom,krait";
+			reg = <2>;
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "qcom,krait";
+			reg = <3>;
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+			qcom,saw = <&saw_l2>;
+		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc",
+						"arm,idle-state";
+				entry-latency-us = <150>;
+				exit-latency-us = <200>;
+				min-residency-us = <2000>;
+			};
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-apq8084", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 7 0xf04>;
+	};
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2 0xf08>,
+			     <GIC_PPI 3 0xf08>,
+			     <GIC_PPI 4 0xf08>,
+			     <GIC_PPI 1 0xf08>;
+		clock-frequency = <19200000>;
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+		memory-region = <&smem_mem>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+		};
+
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,apq8084-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,apq8084-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d2 {
+				reg = <0xd1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d2 {
+				reg = <0xd2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1: s5-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1: s7-p1@d6 {
+				reg = <0xd6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s8_p1: s8-p1@d7 {
+				reg = <0xd7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_mode: mode@d7 {
+				reg = <0xd7 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s9_p1: s9-p1@d8 {
+				reg = <0xd8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s10_p1: s10_p1@d8 {
+				reg = <0xd8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_base2: base2@d9 {
+				reg = <0xd9 0x2>;
+				bits = <4 8>;
+			};
+
+			tsens_s0_p2: s0-p2@da {
+				reg = <0xda 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@db {
+				reg = <0xdb 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p2: s2-p2@dc {
+				reg = <0xdc 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s3_p2: s3-p2@dc {
+				reg = <0xdc 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s4_p2: s4-p2@dd {
+				reg = <0xdd 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@de {
+				reg = <0xde 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@df {
+				reg = <0xdf 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@e0 {
+				reg = <0xe0 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s8_p2: s8-p2@e0 {
+				reg = <0xe0 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s9_p2: s9-p2@e1 {
+				reg = <0xe1 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10_p2@e2 {
+				reg = <0xe2 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p2_backup: s5-p2_backup@e3 {
+				reg = <0xe3 0x2>;
+				bits = <0 6>;
+			};
+
+			tsens_mode_backup: mode_backup@e3 {
+				reg = <0xe3 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s6_p2_backup: s6-p2_backup@e4 {
+				reg = <0xe4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2_backup: s7-p2_backup@e4 {
+				reg = <0xe4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p2_backup: s8-p2_backup@e5 {
+				reg = <0xe5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s9_p2_backup: s9-p2_backup@e6 {
+				reg = <0xe6 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s10_p2_backup: s10_p2_backup@e7 {
+				reg = <0xe7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_base1_backup: base1_backup@440 {
+				reg = <0x440 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1_backup: s0-p1_backup@441 {
+				reg = <0x441 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1_backup: s1-p1_backup@442 {
+				reg = <0x441 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1_backup: s2-p1_backup@442 {
+				reg = <0x442 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1_backup: s3-p1_backup@443 {
+				reg = <0x443 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1_backup: s4-p1_backup@444 {
+				reg = <0x444 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1_backup: s5-p1_backup@444 {
+				reg = <0x444 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1_backup: s6-p1_backup@445 {
+				reg = <0x445 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1_backup: s7-p1_backup@446 {
+				reg = <0x446 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_use_backup: use_backup@447 {
+				reg = <0x447 0x1>;
+				bits = <5 3>;
+			};
+
+			tsens_s8_p1_backup: s8-p1_backup@448 {
+				reg = <0x448 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p1_backup: s9-p1_backup@448 {
+				reg = <0x448 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1_backup: s10_p1_backup@449 {
+				reg = <0x449 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2_backup: base2_backup@44a {
+				reg = <0x44a 0x2>;
+				bits = <2 8>;
+			};
+
+			tsens_s0_p2_backup: s0-p2_backup@44b {
+				reg = <0x44b 0x3>;
+				bits = <2 6>;
+			};
+
+			tsens_s1_p2_backup: s1-p2_backup@44c {
+				reg = <0x44c 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2_backup: s2-p2_backup@44c {
+				reg = <0x44c 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p2_backup: s3-p2_backup@44d {
+				reg = <0x44d 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p2_backup: s4-p2_backup@44e {
+				reg = <0x44e 0x1>;
+				bits = <2 6>;
+			};
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_use_backup>,
+				      <&tsens_mode_backup>,
+				      <&tsens_base1_backup>, <&tsens_base2_backup>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>,
+				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "use_backup",
+					   "mode_backup",
+					   "base1_backup", "base2_backup",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2",
+					   "s0_p1_backup", "s0_p2_backup",
+					   "s1_p1_backup", "s1_p2_backup",
+					   "s2_p1_backup", "s2_p2_backup",
+					   "s3_p1_backup", "s3_p2_backup",
+					   "s4_p1_backup", "s4_p2_backup",
+					   "s5_p1_backup", "s5_p2_backup",
+					   "s6_p1_backup", "s6_p2_backup",
+					   "s7_p1_backup", "s7_p2_backup",
+					   "s8_p1_backup", "s8_p2_backup",
+					   "s9_p1_backup", "s9_p2_backup",
+					   "s10_p1_backup", "s10_p2_backup";
+			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+		timer@f9020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		saw0: power-controller@f9089000 {
+			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw1: power-controller@f9099000 {
+			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw2: power-controller@f90a9000 {
+			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw3: power-controller@f90b9000 {
+			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw_l2: power-controller@f9012000 {
+			compatible = "qcom,saw2";
+			reg = <0xf9012000 0x1000>;
+			regulator;
+		};
+
+		acc0: power-manager@f9088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9088000 0x1000>,
+			      <0xf9008000 0x1000>;
+		};
+
+		acc1: power-manager@f9098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9098000 0x1000>,
+			      <0xf9008000 0x1000>;
+		};
+
+		acc2: power-manager@f90a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90a8000 0x1000>,
+			      <0xf9008000 0x1000>;
+		};
+
+		acc3: power-manager@f90b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90b8000 0x1000>,
+			      <0xf9008000 0x1000>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-apq8084";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfc400000 0x4000>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <0>, /* ufs */
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>, /* sata */
+				 <0>,
+				 <0>; /* pcie */
+			clock-names = "xo",
+				      "sleep_clk",
+				      "ufs_rx_symbol_0_clk_src",
+				      "ufs_rx_symbol_1_clk_src",
+				      "ufs_tx_symbol_0_clk_src",
+				      "ufs_tx_symbol_1_clk_src",
+				      "sata_asic0_clk",
+				      "sata_rx_clk",
+				      "pcie_pipe";
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,apq8084-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,apq8084-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 147>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		blsp2_uart2: serial@f995e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf995e000 0x1000>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			status = "disabled";
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm-requests {
+				compatible = "qcom,rpm-apq8084";
+				qcom,smd-channels = "rpm_requests";
+
+				regulators-0 {
+					compatible = "qcom,rpm-pma8084-regulators";
+
+					pma8084_s1: s1 {};
+					pma8084_s2: s2 {};
+					pma8084_s3: s3 {};
+					pma8084_s4: s4 {};
+					pma8084_s5: s5 {};
+					pma8084_s6: s6 {};
+					pma8084_s7: s7 {};
+					pma8084_s8: s8 {};
+					pma8084_s9: s9 {};
+					pma8084_s10: s10 {};
+					pma8084_s11: s11 {};
+					pma8084_s12: s12 {};
+
+					pma8084_l1: l1 {};
+					pma8084_l2: l2 {};
+					pma8084_l3: l3 {};
+					pma8084_l4: l4 {};
+					pma8084_l5: l5 {};
+					pma8084_l6: l6 {};
+					pma8084_l7: l7 {};
+					pma8084_l8: l8 {};
+					pma8084_l9: l9 {};
+					pma8084_l10: l10 {};
+					pma8084_l11: l11 {};
+					pma8084_l12: l12 {};
+					pma8084_l13: l13 {};
+					pma8084_l14: l14 {};
+					pma8084_l15: l15 {};
+					pma8084_l16: l16 {};
+					pma8084_l17: l17 {};
+					pma8084_l18: l18 {};
+					pma8084_l19: l19 {};
+					pma8084_l20: l20 {};
+					pma8084_l21: l21 {};
+					pma8084_l22: l22 {};
+					pma8084_l23: l23 {};
+					pma8084_l24: l24 {};
+					pma8084_l25: l25 {};
+					pma8084_l26: l26 {};
+					pma8084_l27: l27 {};
+
+					pma8084_lvs1: lvs1 {};
+					pma8084_lvs2: lvs2 {};
+					pma8084_lvs3: lvs3 {};
+					pma8084_lvs4: lvs4 {};
+
+					pma8084_5vs1: 5vs1 {};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
new file mode 100644
index 000000000000..1b27edce9d4f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/leds/common.h>
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+	model = "ALFA Network AP120C-AC Bit";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "ap120c-ac:green:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-wlan {
+			label = "ap120c-ac:green:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-support {
+			label = "ap120c-ac:green:support";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
new file mode 100644
index 000000000000..a707057c887d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/leds/common.h>
+#include "qcom-ipq4018-ap120c-ac.dtsi"
+
+/ {
+	leds {
+		compatible = "gpio-leds";
+
+		status: led-status {
+			label = "ap120c-ac:blue:status";
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		led-wlan2g {
+			label = "ap120c-ac:green:wlan2g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		led-wlan5g {
+			label = "ap120c-ac:red:wlan5g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
new file mode 100644
index 000000000000..d90b4f4c63af
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
@@ -0,0 +1,277 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "ALFA Network AP120C-AC";
+	compatible = "alfa-network,ap120c-ac", "qcom,ipq4018";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+};
+
+&tlmm {
+	i2c0_pins: i2c0_pinmux {
+		mux_i2c {
+			function = "blsp_i2c0";
+			pins = "gpio58", "gpio59";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio_pins: mdio_pinmux {
+		mux_mdio {
+			pins = "gpio53";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_mdc {
+			pins = "gpio52";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial0_pins: serial0_pinmux {
+		mux_uart {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi0_pins: spi0_pinmux {
+		mux_spi {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		mux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio4";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	usb-power-hog {
+		line-name = "USB-power";
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		gpio-hog;
+		output-high;
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&prng {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	tpm@29 {
+		compatible = "atmel,at97sc3204t";
+		reg = <0x29>;
+	};
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "u-boot-env";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "u-boot";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
+			};
+
+			partition@180000 {
+				label = "priv_data1";
+				reg = <0x00180000 0x00010000>;
+				read-only;
+			};
+
+			partition@190000 {
+				label = "priv_data2";
+				reg = <0x00190000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	flash@1 {
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ubi1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "ubi2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial0_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+};
+
+&wifi0 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_1000>;
+};
+
+&wifi1 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_5000>;
+	qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+
+	dwc3@8a00000 {
+		phys = <&usb3_hs_phy>;
+		phy-names = "usb2-phy";
+	};
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
new file mode 100644
index 000000000000..365fbac417fd
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2018, Robert Marko <robimarko@gmail.com>
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "8devices Jalapeno";
+	compatible = "8dev,jalapeno", "qcom,ipq4018";
+};
+
+&tlmm {
+	mdio_pins: mdio_pinmux {
+		pinmux_1 {
+			pins = "gpio53";
+			function = "mdio";
+		};
+
+		pinmux_2 {
+			pins = "gpio52";
+			function = "mdc";
+		};
+
+		pinconf {
+			pins = "gpio52", "gpio53";
+			bias-pull-up;
+		};
+	};
+
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio59";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&prng {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		status = "okay";
+
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "u-boot-env";
+				reg = <0x000e0000 0x00010000>;
+			};
+
+			partition@f0000 {
+				label = "u-boot";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+
+	spi-nand@1 {
+		status = "okay";
+
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ubi1";
+				reg = <0x00000000 0x04000000>;
+			};
+
+			partition@4000000 {
+				label = "ubi2";
+				reg = <0x04000000 0x04000000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+};
+
+&wifi0 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&wifi1 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
new file mode 100644
index 000000000000..ddaa273f72ca
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
@@ -0,0 +1,22 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019-ap.dk01.1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1";
+	compatible = "qcom,ipq4019-ap-dk01.1-c1", "qcom,ipq4019";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
new file mode 100644
index 000000000000..0505270cf508
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
@@ -0,0 +1,113 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include "qcom-ipq4019.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		pinctrl@1000000 {
+			serial_pins: serial_pinmux {
+				mux {
+					pins = "gpio60", "gpio61";
+					function = "blsp_uart0";
+					bias-disable;
+				};
+			};
+
+			spi_0_pins: spi_0_pinmux {
+				pinmux {
+					function = "blsp_spi0";
+					pins = "gpio55", "gpio56", "gpio57";
+				};
+				pinmux_cs {
+					function = "gpio";
+					pins = "gpio54";
+				};
+				pinconf {
+					pins = "gpio55", "gpio56", "gpio57";
+					drive-strength = <12>;
+					bias-disable;
+				};
+				pinconf_cs {
+					pins = "gpio54";
+					drive-strength = <2>;
+					bias-disable;
+					output-high;
+				};
+			};
+		};
+
+		blsp_dma: dma-controller@7884000 {
+			status = "okay";
+		};
+
+		spi@78b5000 {
+			pinctrl-0 = <&spi_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+			cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+			mx25l25635e@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "mx25l25635e";
+				spi-max-frequency = <24000000>;
+			};
+		};
+
+		serial@78af000 {
+			pinctrl-0 = <&serial_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		cryptobam: dma-controller@8e04000 {
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		wifi@a000000 {
+			status = "okay";
+		};
+
+		wifi@a800000 {
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
new file mode 100644
index 000000000000..0993f840d1fc
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019-ap.dk04.1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C1";
+	compatible = "qcom,ipq4019-dk04.1-c1", "qcom,ipq4019";
+
+	soc {
+		dma-controller@7984000 {
+			status = "okay";
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
new file mode 100644
index 000000000000..7765247125e4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019-ap.dk04.1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1-C3";
+	compatible = "qcom,ipq4019-ap-dk04.1-c3", "qcom,ipq4019";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
new file mode 100644
index 000000000000..468ebc40d2ad
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256MB */
+	};
+
+	soc {
+		pinctrl@1000000 {
+			serial_0_pins: serial0-pinmux {
+				pins = "gpio16", "gpio17";
+				function = "blsp_uart0";
+				bias-disable;
+			};
+
+			serial_1_pins: serial1-pinmux {
+				pins = "gpio8", "gpio9",
+					"gpio10", "gpio11";
+				function = "blsp_uart1";
+				bias-disable;
+			};
+
+			spi_0_pins: spi-0-pinmux {
+				pinmux {
+					function = "blsp_spi0";
+					pins = "gpio13", "gpio14", "gpio15";
+					bias-disable;
+				};
+				pinmux_cs {
+					function = "gpio";
+					pins = "gpio12";
+					bias-disable;
+					output-high;
+				};
+			};
+
+			i2c_0_pins: i2c-0-pinmux {
+				pins = "gpio20", "gpio21";
+				function = "blsp_i2c0";
+				bias-disable;
+			};
+
+			nand_pins: nand-pins {
+				pins = "gpio53", "gpio55", "gpio56",
+					"gpio57", "gpio58", "gpio59",
+					"gpio60", "gpio62", "gpio63",
+					"gpio64", "gpio65", "gpio66",
+					"gpio67", "gpio68", "gpio69";
+				function = "qpic";
+			};
+		};
+
+		serial@78af000 {
+			pinctrl-0 = <&serial_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		serial@78b0000 {
+			pinctrl-0 = <&serial_1_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		dma-controller@7884000 {
+			status = "okay";
+		};
+
+		spi@78b5000 { /* BLSP1 QUP1 */
+			pinctrl-0 = <&spi_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
+				spi-max-frequency = <24000000>;
+			};
+		};
+
+		pci@40000000 {
+			status = "okay";
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
new file mode 100644
index 000000000000..ea2987fcbff8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/gpio/gpio.h>
+#include "qcom-ipq4019-ap.dk07.1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C1";
+	compatible = "qcom,ipq4019-ap-dk07.1-c1", "qcom,ipq4019";
+
+	soc {
+		pci@40000000 {
+			status = "okay";
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+		};
+
+		spi@78b6000 {
+			status = "okay";
+		};
+
+		pinctrl@1000000 {
+			serial_1_pins: serial1-pinmux {
+				pins = "gpio8", "gpio9",
+					"gpio10", "gpio11";
+				function = "blsp_uart1";
+				bias-disable;
+			};
+
+			spi_0_pins: spi-0-pinmux {
+				pinmux {
+					function = "blsp_spi0";
+					pins = "gpio13", "gpio14", "gpio15";
+					bias-disable;
+				};
+				pinmux_cs {
+					function = "gpio";
+					pins = "gpio12";
+					bias-disable;
+					output-high;
+				};
+			};
+		};
+
+		serial@78b0000 {
+			pinctrl-0 = <&serial_1_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		spi@78b5000 {
+			pinctrl-0 = <&spi_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+			flash@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0>;
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
+				spi-max-frequency = <24000000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
new file mode 100644
index 000000000000..bd3553dd2070
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019-ap.dk07.1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C2";
+	compatible = "qcom,ipq4019-ap-dk07.1-c2", "qcom,ipq4019";
+
+	soc {
+		pinctrl@1000000 {
+			serial_1_pins: serial1-pinmux {
+				pins = "gpio8", "gpio9";
+				function = "blsp_uart1";
+				bias-disable;
+			};
+		};
+
+		serial@78b0000 {
+			pinctrl-0 = <&serial_1_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
new file mode 100644
index 000000000000..7ef635997efa
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512MB */
+	};
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		pinctrl@1000000 {
+			serial_0_pins: serial0-pinmux {
+				pins = "gpio16", "gpio17";
+				function = "blsp_uart0";
+				bias-disable;
+			};
+
+			i2c_0_pins: i2c-0-pinmux {
+				pins = "gpio20", "gpio21";
+				function = "blsp_i2c0";
+				bias-disable;
+			};
+
+			nand_pins: nand-pins {
+				pins = "gpio53", "gpio55", "gpio56",
+				       "gpio57", "gpio58", "gpio59",
+				       "gpio60", "gpio62", "gpio63",
+				       "gpio64", "gpio65", "gpio66",
+				       "gpio67", "gpio68", "gpio69";
+				function = "qpic";
+                        };
+		};
+
+		serial@78af000 {
+			pinctrl-0 = <&serial_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		dma-controller@7884000 {
+			status = "okay";
+		};
+
+		i2c@78b7000 { /* BLSP1 QUP2 */
+			pinctrl-0 = <&i2c_0_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		dma-controller@7984000 {
+			status = "okay";
+		};
+	};
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
new file mode 100644
index 000000000000..f0ef86fadc9d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
@@ -0,0 +1,698 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/clock/qcom,gcc-ipq4019.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	model = "Qualcomm Technologies, Inc. IPQ4019";
+	compatible = "qcom,ipq4019";
+	interrupt-parent = <&intc>;
+
+	reserved-memory {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges;
+
+		smem_region: smem@87e00000 {
+			reg = <0x87e00000 0x080000>;
+			no-map;
+		};
+
+		tz@87e80000 {
+			reg = <0x87e80000 0x180000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		spi0 = &blsp1_spi1;
+		spi1 = &blsp1_spi2;
+		i2c0 = &blsp1_i2c3;
+		i2c1 = &blsp1_i2c4;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			reg = <0x0>;
+			clocks = <&gcc GCC_APPS_CLK_SRC>;
+			clock-frequency = <0>;
+			clock-latency = <256000>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			reg = <0x1>;
+			clocks = <&gcc GCC_APPS_CLK_SRC>;
+			clock-frequency = <0>;
+			clock-latency = <256000>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			reg = <0x2>;
+			clocks = <&gcc GCC_APPS_CLK_SRC>;
+			clock-frequency = <0>;
+			clock-latency = <256000>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,kpss-acc-v2";
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			reg = <0x3>;
+			clocks = <&gcc GCC_APPS_CLK_SRC>;
+			clock-frequency = <0>;
+			clock-latency = <256000>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+			qcom,saw = <&saw_l2>;
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-48000000 {
+			opp-hz = /bits/ 64 <48000000>;
+			clock-latency-ns = <256000>;
+		};
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			clock-latency-ns = <256000>;
+		};
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			clock-latency-ns = <256000>;
+		};
+		opp-716000000 {
+			opp-hz = /bits/ 64 <716000000>;
+			clock-latency-ns = <256000>;
+ 		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	clocks {
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+
+		xo: xo {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-ipq4019", "qcom,scm";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 2 0xf08>,
+			     <1 3 0xf08>,
+			     <1 4 0xf08>,
+			     <1 1 0xf08>;
+		clock-frequency = <48000000>;
+		always-on;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x0b000000 0x1000>,
+			<0x0b002000 0x1000>;
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,gcc-ipq4019";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x1800000 0x60000>;
+			clocks = <&xo>, <&sleep_clk>;
+			clock-names = "xo", "sleep_clk";
+		};
+
+		prng: rng@22000 {
+			compatible = "qcom,prng";
+			reg = <0x22000 0x140>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+			status = "disabled";
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,ipq4019-pinctrl";
+			reg = <0x01000000 0x300000>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 100>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		vqmmc: regulator@1948000 {
+			compatible = "qcom,vqmmc-ipq4019-regulator";
+			reg = <0x01948000 0x4>;
+			regulator-name = "vqmmc";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+			status = "disabled";
+		};
+
+		sdhci: mmc@7824900 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7824900 0x11c>, <0x7824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			bus-width = <8>;
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>, <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&gcc GCC_DCD_XO_CLK>;
+			clock-names = "iface", "core", "xo";
+			status = "disabled";
+		};
+
+		blsp_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x23000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			status = "disabled";
+		};
+
+		blsp1_spi1: spi@78b5000 { /* BLSP1 QUP1 */
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x78b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_spi2: spi@78b6000 { /* BLSP1 QUP2 */
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x78b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b8000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		cryptobam: dma-controller@8e04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x08e04000 0x20000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <1>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		crypto: crypto@8e3a000 {
+			compatible = "qcom,crypto-v5.1";
+			reg = <0x08e3a000 0x6000>;
+			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_CLK>;
+			clock-names = "iface", "bus", "core";
+			dmas = <&cryptobam 2>, <&cryptobam 3>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		acc0: power-manager@b088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b088000 0x1000>, <0xb008000 0x1000>;
+		};
+
+		acc1: power-manager@b098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b098000 0x1000>, <0xb008000 0x1000>;
+		};
+
+		acc2: power-manager@b0a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b0a8000 0x1000>, <0xb008000 0x1000>;
+		};
+
+		acc3: power-manager@b0b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0x0b0b8000 0x1000>, <0xb008000 0x1000>;
+		};
+
+		saw0: regulator@b089000 {
+			compatible = "qcom,saw2";
+			reg = <0x0b089000 0x1000>, <0x0b009000 0x1000>;
+			regulator;
+		};
+
+		saw1: regulator@b099000 {
+			compatible = "qcom,saw2";
+			reg = <0x0b099000 0x1000>, <0x0b009000 0x1000>;
+			regulator;
+		};
+
+		saw2: regulator@b0a9000 {
+			compatible = "qcom,saw2";
+			reg = <0x0b0a9000 0x1000>, <0x0b009000 0x1000>;
+			regulator;
+		};
+
+		saw3: regulator@b0b9000 {
+			compatible = "qcom,saw2";
+			reg = <0x0b0b9000 0x1000>, <0x0b009000 0x1000>;
+			regulator;
+		};
+
+		saw_l2: regulator@b012000 {
+			compatible = "qcom,saw2";
+			reg = <0xb012000 0x1000>;
+			regulator;
+		};
+
+		blsp1_uart1: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x78af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
+		};
+
+		blsp1_uart2: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x78b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				<&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
+		};
+
+		watchdog: watchdog@b017000 {
+			compatible = "qcom,kpss-wdt-ipq4019", "qcom,kpss-wdt";
+			reg = <0xb017000 0x40>;
+			clocks = <&sleep_clk>;
+			timeout-sec = <10>;
+			status = "disabled";
+		};
+
+		restart@4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x4ab000 0x4>;
+		};
+
+		pcie0: pci@40000000 {
+			compatible = "qcom,pcie-ipq4019";
+			reg =  <0x40000000 0xf1d
+				0x40000f20 0xa8
+				0x80000 0x2000
+				0x40100000 0x1000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x40200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x40300000 0x40300000 0x0 0x00d00000>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			clocks = <&gcc GCC_PCIE_AHB_CLK>,
+				 <&gcc GCC_PCIE_AXI_M_CLK>,
+				 <&gcc GCC_PCIE_AXI_S_CLK>;
+			clock-names = "aux",
+				      "master_bus",
+				      "slave_bus";
+
+			resets = <&gcc PCIE_AXI_M_ARES>,
+				 <&gcc PCIE_AXI_S_ARES>,
+				 <&gcc PCIE_PIPE_ARES>,
+				 <&gcc PCIE_AXI_M_VMIDMT_ARES>,
+				 <&gcc PCIE_AXI_S_XPU_ARES>,
+				 <&gcc PCIE_PARF_XPU_ARES>,
+				 <&gcc PCIE_PHY_ARES>,
+				 <&gcc PCIE_AXI_M_STICKY_ARES>,
+				 <&gcc PCIE_PIPE_STICKY_ARES>,
+				 <&gcc PCIE_PWR_ARES>,
+				 <&gcc PCIE_AHB_ARES>,
+				 <&gcc PCIE_PHY_AHB_ARES>;
+			reset-names = "axi_m",
+				      "axi_s",
+				      "pipe",
+				      "axi_m_vmid",
+				      "axi_s_xpu",
+				      "parf",
+				      "phy",
+				      "axi_m_sticky",
+				      "pipe_sticky",
+				      "pwr",
+				      "ahb",
+				      "phy_ahb";
+
+			status = "disabled";
+		};
+
+		qpic_bam: dma-controller@7984000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x7984000 0x1a000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			status = "disabled";
+		};
+
+		nand: nand-controller@79b0000 {
+			compatible = "qcom,ipq4019-nand";
+			reg = <0x79b0000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&gcc GCC_QPIC_CLK>,
+				 <&gcc GCC_QPIC_AHB_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+
+			nand@0 {
+				reg = <0>;
+
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+				nand-bus-width = <8>;
+			};
+		};
+
+		wifi0: wifi@a000000 {
+			compatible = "qcom,ipq4019-wifi";
+			reg = <0xa000000 0x200000>;
+			resets = <&gcc WIFI0_CPU_INIT_RESET>,
+				 <&gcc WIFI0_RADIO_SRIF_RESET>,
+				 <&gcc WIFI0_RADIO_WARM_RESET>,
+				 <&gcc WIFI0_RADIO_COLD_RESET>,
+				 <&gcc WIFI0_CORE_WARM_RESET>,
+				 <&gcc WIFI0_CORE_COLD_RESET>;
+			reset-names = "wifi_cpu_init", "wifi_radio_srif",
+				      "wifi_radio_warm", "wifi_radio_cold",
+				      "wifi_core_warm", "wifi_core_cold";
+			clocks = <&gcc GCC_WCSS2G_CLK>,
+				 <&gcc GCC_WCSS2G_REF_CLK>,
+				 <&gcc GCC_WCSS2G_RTC_CLK>;
+			clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+				      "wifi_wcss_rtc";
+			interrupts = <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 39 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 40 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
+					   "msi4",  "msi5",  "msi6",  "msi7",
+					   "msi8",  "msi9", "msi10", "msi11",
+					  "msi12", "msi13", "msi14", "msi15",
+					  "legacy";
+			status = "disabled";
+		};
+
+		wifi1: wifi@a800000 {
+			compatible = "qcom,ipq4019-wifi";
+			reg = <0xa800000 0x200000>;
+			resets = <&gcc WIFI1_CPU_INIT_RESET>,
+				 <&gcc WIFI1_RADIO_SRIF_RESET>,
+				 <&gcc WIFI1_RADIO_WARM_RESET>,
+				 <&gcc WIFI1_RADIO_COLD_RESET>,
+				 <&gcc WIFI1_CORE_WARM_RESET>,
+				 <&gcc WIFI1_CORE_COLD_RESET>;
+			reset-names = "wifi_cpu_init", "wifi_radio_srif",
+				      "wifi_radio_warm", "wifi_radio_cold",
+				      "wifi_core_warm", "wifi_core_cold";
+			clocks = <&gcc GCC_WCSS5G_CLK>,
+				 <&gcc GCC_WCSS5G_REF_CLK>,
+				 <&gcc GCC_WCSS5G_RTC_CLK>;
+			clock-names = "wifi_wcss_cmd", "wifi_wcss_ref",
+				      "wifi_wcss_rtc";
+			interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 49 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 51 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 53 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 54 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 55 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 56 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 58 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 59 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 60 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 61 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
+					   "msi4",  "msi5",  "msi6",  "msi7",
+					   "msi8",  "msi9", "msi10", "msi11",
+					  "msi12", "msi13", "msi14", "msi15",
+					  "legacy";
+			status = "disabled";
+		};
+
+		mdio: mdio@90000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "qcom,ipq4019-mdio";
+			reg = <0x90000 0x64>;
+			status = "disabled";
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+
+			ethphy4: ethernet-phy@4 {
+				reg = <4>;
+			};
+		};
+
+		usb3_ss_phy: ssphy@9a000 {
+			compatible = "qcom,usb-ss-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0x9a000 0x800>;
+			reg-names = "phy_base";
+			resets = <&gcc USB3_UNIPHY_PHY_ARES>;
+			reset-names = "por_rst";
+			status = "disabled";
+		};
+
+		usb3_hs_phy: hsphy@a6000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa6000 0x40>;
+			reg-names = "phy_base";
+			resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb3: usb3@8af8800 {
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
+			reg = <0x8af8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB3_MASTER_CLK>,
+				 <&gcc GCC_USB3_SLEEP_CLK>,
+				 <&gcc GCC_USB3_MOCK_UTMI_CLK>;
+			clock-names = "core", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			dwc3@8a00000 {
+				compatible = "snps,dwc3";
+				reg = <0x8a00000 0xf8000>;
+				interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+			};
+		};
+
+		usb2_hs_phy: hsphy@a8000 {
+			compatible = "qcom,usb-hs-ipq4019-phy";
+			#phy-cells = <0>;
+			reg = <0xa8000 0x40>;
+			reg-names = "phy_base";
+			resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
+			reset-names = "por_rst", "srif_rst";
+			status = "disabled";
+		};
+
+		usb2: usb2@60f8800 {
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
+			reg = <0x60f8800 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&gcc GCC_USB2_MASTER_CLK>,
+				 <&gcc GCC_USB2_SLEEP_CLK>,
+				 <&gcc GCC_USB2_MOCK_UTMI_CLK>;
+			clock-names = "master", "sleep", "mock_utmi";
+			ranges;
+			status = "disabled";
+
+			dwc3@6000000 {
+				compatible = "snps,dwc3";
+				reg = <0x6000000 0xf8000>;
+				interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_hs_phy>;
+				phy-names = "usb2-phy";
+				dr_mode = "host";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
new file mode 100644
index 000000000000..9d06255104c7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8062.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
new file mode 100644
index 000000000000..5d3ebd3e2e51
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8062";
+	compatible = "qcom,ipq8062", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
new file mode 100644
index 000000000000..a654d3c22c4f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064-v1.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064/AP-148";
+	compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
+
+	soc {
+		pinmux@800000 {
+			buttons_pins: buttons_pins {
+				mux {
+					pins = "gpio54", "gpio65";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			i2c@16380000 {
+				status = "okay";
+				clock-frequency = <200000>;
+				pinctrl-0 = <&i2c4_pins>;
+				pinctrl-names = "default";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
new file mode 100644
index 000000000000..104eb729c2d6
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
@@ -0,0 +1,474 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "MikroTik RB3011UiAS-RM";
+	compatible = "mikrotik,rb3011", "qcom,ipq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac3;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
+	};
+
+	chosen {
+		bootargs = "loglevel=8 console=ttyMSM0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@42000000 {
+		reg = <0x42000000 0x3e000000>;
+		device_type = "memory";
+	};
+
+	mdio0: mdio-0 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio0_pins>;
+		pinctrl-names = "default";
+
+		switch0: switch@10 {
+			compatible = "qca,qca8337";
+
+			dsa,member = <0 0>;
+
+			pinctrl-0 = <&sw0_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch0cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii-id";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw1";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw2";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw3";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw4";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw5";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+			};
+		};
+	};
+
+	mdio1: mdio-1 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio1_pins>;
+		pinctrl-names = "default";
+
+		switch1: switch@14 {
+			compatible = "qca,qca8337";
+
+			dsa,member = <1 0>;
+
+			pinctrl-0 = <&sw1_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch1cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac3>;
+					phy-mode = "sgmii";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw6";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw7";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw8";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw9";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw10";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
+				};
+			};
+		};
+	};
+
+	soc {
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+				spi-max-frequency = <50000000>;
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				norflash: flash@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "RouterBoot";
+						reg = <0x0 0x40000>;
+					};
+				};
+			};
+		};
+
+		gpio-keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&buttons_pins>;
+			pinctrl-names = "default";
+
+			button {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led-0 {
+				label = "rb3011:green:user";
+				color = <LED_COLOR_ID_GREEN>;
+				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+	};
+};
+
+&adm_dma {
+	status = "okay";
+};
+
+&gmac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+	phy-handle = <&switch0cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac3 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <3>;
+	phy-handle = <&switch1cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi7 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&hs_phy_1 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				label = "RouterBoard NAND 1 Boot";
+				reg = <0x0000000 0x0800000>;
+			};
+
+			main@800000 {
+				label = "RouterBoard NAND 1 Main";
+				reg = <0x0800000 0x7800000>;
+			};
+		};
+	};
+};
+
+&qcom_pinmux {
+	buttons_pins: buttons_pins {
+		mux {
+			pins = "gpio66";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	leds_pins: leds_pins {
+		mux {
+			pins = "gpio33";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio1_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	sw0_reset_pin: sw0_reset_pin {
+		mux {
+			pins = "gpio16";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	sw1_reset_pin: sw1_reset_pin {
+		mux {
+			pins = "gpio17";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	usb1_pwr_en_pins: usb1_pwr_en_pins {
+		mux {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&ss_phy_1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	pinctrl-0 = <&usb1_pwr_en_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
new file mode 100644
index 000000000000..ac9c44f0c164
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
new file mode 100644
index 000000000000..c5abe7151f14
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "okay";
+
+			serial@16340000 {
+				status = "okay";
+			};
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+				spi-max-frequency = <50000000>;
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 0>;
+
+				flash: flash@0 {
+					compatible = "s25fl256s1";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "rootfs";
+						reg = <0x0 0x1000000>;
+					};
+
+					partition@1 {
+						label = "scratch";
+						reg = <0x1000000 0x1000000>;
+					};
+				};
+			};
+		};
+
+		sata-phy@1b400000 {
+			status = "okay";
+		};
+
+		sata@29000000 {
+			ports-implemented = <0x1>;
+			status = "okay";
+		};
+
+		gpio-keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&buttons_pins>;
+			pinctrl-names = "default";
+
+			button-1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+			button-2 {
+				label = "wps";
+				linux,code = <KEY_WPS_BUTTON>;
+				gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led-0 {
+				label = "led_usb1";
+				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "usbdev";
+				default-state = "off";
+			};
+
+			led-1 {
+				label = "led_usb3";
+				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "usbdev";
+				default-state = "off";
+			};
+
+			led-2 {
+				label = "status_led_fail";
+				function = LED_FUNCTION_STATUS;
+				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led-3 {
+				label = "sata_led";
+				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+
+			led-4 {
+				label = "status_led_pass";
+				function = LED_FUNCTION_STATUS;
+				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
new file mode 100644
index 000000000000..0442580b22de
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
new file mode 100644
index 000000000000..2f117d576daf
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v2.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	 * The i2c device on gsbi4 should not be enabled.
+	 * On ipq806x designs gsbi4 i2c is meant for exclusive
+	 * RPM usage. Turning this on in kernel manifests as
+	 * i2c failure for the RPM.
+	 */
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
new file mode 100644
index 000000000000..6198f42f6a9c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
@@ -0,0 +1,1377 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/clock/qcom,gcc-ipq806x.h>
+#include <dt-bindings/clock/qcom,lcc-ipq806x.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm IPQ8064";
+	compatible = "qcom,ipq8064";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	thermal-zones {
+		sensor0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor4-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor5-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor6-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor7-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor8-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor9-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		sensor10-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				cpu-critical {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+
+				cpu-hot {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+					  IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		nss@40000000 {
+			reg = <0x40000000 0x1000000>;
+			no-map;
+		};
+
+		smem: smem@41000000 {
+			compatible = "qcom,smem";
+			reg = <0x41000000 0x200000>;
+			no-map;
+
+			hwlocks = <&sfpb_mutex 3>;
+		};
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+
+		pxo_board: pxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			#clock-cells = <0>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-ipq806x", "qcom,scm";
+		};
+	};
+
+	stmmac_axi_setup: stmmac-axi-config {
+		snps,wr_osr_lmt = <7>;
+		snps,rd_osr_lmt = <7>;
+		snps,blen = <16 0 0 0 0 0 0>;
+	};
+
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x00108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+		};
+
+		qcom,ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		qfprom: qfprom@700000 {
+			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			speedbin_efuse: speedbin@c0 {
+				reg = <0xc0 0x4>;
+			};
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib_backup@410 {
+				reg = <0x410 0xb>;
+			};
+		};
+
+		qcom_pinmux: pinmux@800000 {
+			compatible = "qcom,ipq8064-pinctrl";
+			reg = <0x00800000 0x4000>;
+
+			gpio-controller;
+			gpio-ranges = <&qcom_pinmux 0 0 69>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+			pcie0_pins: pcie0_pinmux {
+				mux {
+					pins = "gpio3";
+					function = "pcie1_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			pcie1_pins: pcie1_pinmux {
+				mux {
+					pins = "gpio48";
+					function = "pcie2_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			pcie2_pins: pcie2_pinmux {
+				mux {
+					pins = "gpio63";
+					function = "pcie3_rst";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
+
+			i2c4_pins: i2c4-default {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				drive-strength = <12>;
+				bias-disable;
+			};
+
+			spi_pins: spi_pins {
+				mux {
+					pins = "gpio18", "gpio19", "gpio21";
+					function = "gsbi5";
+					drive-strength = <10>;
+					bias-none;
+				};
+			};
+
+			leds_pins: leds_pins {
+				mux {
+					pins = "gpio7", "gpio8", "gpio9",
+					       "gpio26", "gpio53";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+					output-low;
+				};
+			};
+
+			buttons_pins: buttons_pins {
+				mux {
+					pins = "gpio54";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			nand_pins: nand_pins {
+				mux {
+					pins = "gpio34", "gpio35", "gpio36",
+					       "gpio37", "gpio38", "gpio39",
+					       "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				pullups {
+					pins = "gpio39";
+					function = "nand";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				hold {
+					pins = "gpio40", "gpio41", "gpio42",
+					       "gpio43", "gpio44", "gpio45",
+					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
+					bias-bus-hold;
+				};
+			};
+
+			mdio0_pins: mdio0-pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2-pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29",
+					       "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59",
+					       "gpio60", "gpio61", "gpio62";
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-ipq8064", "syscon";
+			clocks = <&pxo_board>, <&cxo_board>, <&lcc PLL4>;
+			clock-names = "pxo", "cxo", "pll4";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			tsens: thermal-sensor {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		sfpb_mutex: hwlock@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+
+			#hwlock-cells = <1>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-ipq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
+						 IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <25000000>;
+			clocks = <&sleep_clk>;
+			clock-names = "sleep";
+			cpu-offset = <0x80000>;
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
+		acc0: clock-controller@2088000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: regulator@2089000 {
+			compatible = "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		acc1: clock-controller@2098000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
+		};
+
+		saw1: regulator@2099000 {
+			compatible = "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		nss_common: syscon@3000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
+
+		usb3_0: usb@100f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_0: usb@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_1: usb@110f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: usb@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba: amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <192000000>;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		gsbi1: gsbi@12440000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x12440000 0x100>;
+			cell-index = <1>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_serial: serial@12450000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12450000 0x100>,
+				      <0x12400000 0x03>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+
+				status = "disabled";
+			};
+
+			gsbi1_i2c: i2c@12460000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x12460000 0x1000>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi2: gsbi@12480000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x12480000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi2_serial: serial@12490000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12490000 0x1000>,
+				      <0x12480000 0x1000>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi2_i2c: i2c@124a0000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x124a0000 0x1000>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x100>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x1000>,
+				      <0x16300000 0x1000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			i2c@16380000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16380000 0x1000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gsbi6: gsbi@16500000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x16500000 0x100>;
+			cell-index = <6>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			gsbi6_spi: spi@16580000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
+		gsbi5: gsbi@1a200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x1a200000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_serial: serial@1a240000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x1a240000 0x1000>,
+				      <0x1a200000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			i2c@1a280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			spi@1a280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x1a280000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-ipq8064", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
+		nand: nand-controller@1ac00000 {
+			compatible = "qcom,ipq806x-nand";
+			reg = <0x1ac00000 0x800>;
+
+			pinctrl-0 = <&nand_pins>;
+			pinctrl-names = "default";
+
+			clocks = <&gcc EBI2_CLK>,
+				 <&gcc EBI2_AON_CLK>;
+			clock-names = "core", "aon";
+
+			dmas = <&adm_dma 3>;
+			dma-names = "rxtx";
+			qcom,cmd-crci = <15>;
+			qcom,data-crci = <3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sata_phy: sata-phy@1b400000 {
+			compatible = "qcom,ipq806x-sata-phy";
+			reg = <0x1b400000 0x200>;
+
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		pcie0: pci@1b500000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b500000 0x1000
+			       0x1b502000 0x80
+			       0x1b600000 0x100
+			       0x0ff00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_A_CLK>,
+				 <&gcc PCIE_H_CLK>,
+				 <&gcc PCIE_PHY_CLK>,
+				 <&gcc PCIE_AUX_CLK>,
+				 <&gcc PCIE_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_ACLK_RESET>,
+				 <&gcc PCIE_HCLK_RESET>,
+				 <&gcc PCIE_POR_RESET>,
+				 <&gcc PCIE_PCI_RESET>,
+				 <&gcc PCIE_PHY_RESET>,
+				 <&gcc PCIE_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie0_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+		};
+
+		pcie1: pci@1b700000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b700000 0x1000
+			       0x1b702000 0x80
+			       0x1b800000 0x100
+			       0x31f00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x31e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x2e000000 0x2e000000 0x0 0x03e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_1_A_CLK>,
+				 <&gcc PCIE_1_H_CLK>,
+				 <&gcc PCIE_1_PHY_CLK>,
+				 <&gcc PCIE_1_AUX_CLK>,
+				 <&gcc PCIE_1_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_1_ACLK_RESET>,
+				 <&gcc PCIE_1_HCLK_RESET>,
+				 <&gcc PCIE_1_POR_RESET>,
+				 <&gcc PCIE_1_PCI_RESET>,
+				 <&gcc PCIE_1_PHY_RESET>,
+				 <&gcc PCIE_1_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie1_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+		};
+
+		pcie2: pci@1b900000 {
+			compatible = "qcom,pcie-ipq8064";
+			reg = <0x1b900000 0x1000
+			       0x1b902000 0x80
+			       0x1ba00000 0x100
+			       0x35f00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <2>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0x0 0x00000000 0x35e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x32000000 0x32000000 0x0 0x03e00000>; /* MEM */
+
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc PCIE_2_A_CLK>,
+				 <&gcc PCIE_2_H_CLK>,
+				 <&gcc PCIE_2_PHY_CLK>,
+				 <&gcc PCIE_2_AUX_CLK>,
+				 <&gcc PCIE_2_ALT_REF_CLK>;
+			clock-names = "core", "iface", "phy", "aux", "ref";
+
+			assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc PCIE_2_ACLK_RESET>,
+				 <&gcc PCIE_2_HCLK_RESET>,
+				 <&gcc PCIE_2_POR_RESET>,
+				 <&gcc PCIE_2_PCI_RESET>,
+				 <&gcc PCIE_2_PHY_RESET>,
+				 <&gcc PCIE_2_EXT_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy", "ext";
+
+			pinctrl-0 = <&pcie2_pins>;
+			pinctrl-names = "default";
+
+			status = "disabled";
+			perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
+		};
+
+		qsgmii_csr: syscon@1bb00000 {
+			compatible = "syscon";
+			reg = <0x1bb00000 0x000001FF>;
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-ipq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass@28100000 {
+			compatible = "qcom,lpass-cpu";
+			status = "disabled";
+			clocks = <&lcc AHBIX_CLK>,
+					<&lcc MI2S_OSR_CLK>,
+					<&lcc MI2S_BIT_CLK>;
+			clock-names = "ahbix-clk",
+					"mi2s-osr-clk",
+					"mi2s-bit-clk";
+			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "lpass-irq-lpaif";
+			reg = <0x28100000 0x10000>;
+			reg-names = "lpass-lpaif";
+		};
+
+		sata: sata@29000000 {
+			compatible = "qcom,ipq806x-ahci", "generic-ahci";
+			reg = <0x29000000 0x180>;
+
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_face", "iface", "core",
+					"rxoob", "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		gmac0: ethernet@37000000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37000000 0x200000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE1_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE1_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac1: ethernet@37200000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37200000 0x200000>;
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE2_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE2_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac2: ethernet@37400000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37400000 0x200000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE3_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE3_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+
+		gmac3: ethernet@37600000 {
+			device_type = "network";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
+			reg = <0x37600000 0x200000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+
+			snps,axi-config = <&stmmac_axi_setup>;
+			snps,pbl = <32>;
+			snps,aal;
+
+			qcom,nss-common = <&nss_common>;
+			qcom,qsgmii-csr = <&qsgmii_csr>;
+
+			clocks = <&gcc GMAC_CORE4_CLK>;
+			clock-names = "stmmaceth";
+
+			resets = <&gcc GMAC_CORE4_RESET>,
+				 <&gcc GMAC_AHB_RESET>;
+			reset-names = "stmmaceth", "ahb";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
new file mode 100644
index 000000000000..803e6ff99ef8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8065.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
new file mode 100644
index 000000000000..ea49f6cc416d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
new file mode 100644
index 000000000000..b269fdca1460
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for mangOH Green Board with WP8548 Module
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <dt-bindings/input/input.h>
+
+#include "qcom-mdm9615-wp8548.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "MangOH Green with WP8548 Module";
+	compatible = "swir,mangoh-green-wp8548", "swir,wp8548", "qcom,mdm9615";
+
+	aliases {
+		spi0 = &gsbi3_spi;
+		serial0 = &gsbi4_serial;
+		serial1 = &gsbi5_serial;
+		i2c0 = &gsbi5_i2c;
+		mmc0 = &sdcc1;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&msmgpio {
+	/* MangOH GPIO Mapping :
+	 * - 2 : GPIOEXP_INT2
+	 * - 7 : IOT1_GPIO2
+	 * - 8 : IOT0_GPIO4
+	 * - 13: IOT0_GPIO3
+	 * - 21: IOT1_GPIO4
+	 * - 22: IOT2_GPIO1
+	 * - 23: IOT2_GPIO2
+	 * - 24: IOT2_GPIO3
+	 * - 25: IOT1_GPIO1
+	 * - 32: IOT1_GPIO3
+	 * - 33: IOT0_GPIO2
+	 * - 42: IOT0_GPIO1 and SD Card Detect
+	 */
+
+	gpioext1_pins: gpioext1-state {
+		gpioext1-pins {
+			pins = "gpio2";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	sdc_cd_pins: sdc-cd-state {
+		sdc-cd-pins {
+			pins = "gpio42";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&gsbi3_spi {
+	spi@0 {
+		compatible = "swir,mangoh-iotport-spi";
+		spi-max-frequency = <24000000>;
+		reg = <0>;
+	};
+};
+
+&gsbi5_i2c {
+	mux@71 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+
+		i2c_iot0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c_iot1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c_iot2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			usbhub: hub@8 {
+				compatible = "smsc,usb3503a";
+				reg = <0x8>;
+				connect-gpios = <&gpioext2 1 GPIO_ACTIVE_HIGH>;
+				intn-gpios = <&gpioext2 0 GPIO_ACTIVE_HIGH>;
+				initial-mode = <1>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			gpioext0: pinctrl@3e {
+				/* GPIO Expander 0 Mapping :
+				 * - 0: ARDUINO_RESET_Level shift
+				 * - 1: BattChrgr_PG_N
+				 * - 2: BattGauge_GPIO
+				 * - 3: LED_ON (out active high)
+				 * - 4: ATmega_reset_GPIO
+				 * - 5: X
+				 * - 6: PCM_ANALOG_SELECT (out active high)
+				 * - 7: X
+				 * - 8: Board_rev_res1 (in)
+				 * - 9: Board_rev_res2 (in)
+				 * - 10: UART_EXP1_ENn (out active low / pull-down)
+				 * - 11: UART_EXP1_IN (out pull-down)
+				 * - 12: UART_EXP2_IN (out pull-down)
+				 * - 13: SDIO_SEL (out pull-down)
+				 * - 14: SPI_EXP1_ENn (out active low / pull-down)
+				 * - 15: SPI_EXP1_IN (out pull-down)
+				 */
+				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
+				compatible = "semtech,sx1509q";
+				reg = <0x3e>;
+				interrupt-parent = <&gpioext1>;
+				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+				semtech,probe-reset;
+
+				gpio-controller;
+				interrupt-controller;
+			};
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			gpioext1: pinctrl@3f {
+				/* GPIO Expander 1 Mapping :
+				 * - 0: GPIOEXP_INT1
+				 * - 1: Battery detect
+				 * - 2: GPIO_SCF3_RESET
+				 * - 3: LED_CARD_DETECT_IOT0 (in)
+				 * - 4: LED_CARD_DETECT_IOT1 (in)
+				 * - 5: LED_CARD_DETECT_IOT2 (in)
+				 * - 6: UIM2_PWM_SELECT
+				 * - 7: UIM2_M2_S_SELECT
+				 * - 8: TP900
+				 * - 9: SENSOR_INT1 (in)
+				 * - 10: SENSOR_INT2 (in)
+				 * - 11: CARD_DETECT_IOT0 (in pull-up)
+				 * - 12: CARD_DETECT_IOT2 (in pull-up)
+				 * - 13: CARD_DETECT_IOT1 (in pull-up)
+				 * - 14: GPIOEXP_INT3 (in active low / pull-up)
+				 * - 15: BattChrgr_INT_N
+				 */
+				pinctrl-0 = <&gpioext1_pins>;
+				pinctrl-names = "default";
+
+				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
+				compatible = "semtech,sx1509q";
+				reg = <0x3f>;
+				interrupt-parent = <&msmgpio>;
+				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+				semtech,probe-reset;
+
+				gpio-controller;
+				interrupt-controller;
+			};
+		};
+
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			gpioext2: pinctrl@70 {
+				/* GPIO Expander 2 Mapping :
+				 * - 0: USB_HUB_INTn
+				 * - 1: HUB_CONNECT
+				 * - 2: GPIO_IOT2_RESET (out active low / pull-up)
+				 * - 3: GPIO_IOT1_RESET (out active low / pull-up)
+				 * - 4: GPIO_IOT0_RESET (out active low / pull-up)
+				 * - 5: TP901
+				 * - 6: TP902
+				 * - 7: TP903
+				 * - 8: UART_EXP2_ENn (out active low / pull-down)
+				 * - 9: PCM_EXP1_ENn (out active low)
+				 * - 10: PCM_EXP1_SEL (out)
+				 * - 11: ARD_FTDI
+				 * - 12: TP904
+				 * - 13: TP905
+				 * - 14: TP906
+				 * - 15: RS232_Enable (out active high / pull-up)
+				 */
+				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
+				compatible = "semtech,sx1509q";
+				reg = <0x70>;
+				interrupt-parent = <&gpioext1>;
+				interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+
+				semtech,probe-reset;
+
+				gpio-controller;
+				interrupt-controller;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&sdcc1 {
+	pinctrl-0 = <&sdc_cd_pins>;
+	pinctrl-names = "default";
+	disable-wp;
+	cd-gpios = <&msmgpio 42 GPIO_ACTIVE_LOW>; /* Active low CD */
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
new file mode 100644
index 000000000000..92c8003dac25
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Sierra Wireless WP8548 Module
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "qcom-mdm9615.dtsi"
+
+/ {
+	model = "Sierra Wireless WP8548 Module";
+	compatible = "swir,wp8548", "qcom,mdm9615";
+
+	memory@48000000 {
+		device_type = "memory";
+		reg = <0x48000000 0x7F00000>;
+	};
+};
+
+&msmgpio {
+	pinctrl-0 = <&reset_out_pins>;
+	pinctrl-names = "default";
+
+	gsbi3_pins: gsbi3-state {
+		gsbi3-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "gsbi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi4_pins: gsbi4-state {
+		gsbi4-pins {
+			pins = "gpio12", "gpio13", "gpio14", "gpio15";
+			function = "gsbi4";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_i2c_pins: gsbi5-i2c-state {
+		sda-pins {
+			pins = "gpio16";
+			function = "gsbi5_i2c";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		scl-pins {
+			pins = "gpio17";
+			function = "gsbi5_i2c";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_uart_pins: gsbi5-uart-state {
+		gsbi5-uart-pins {
+			pins = "gpio18", "gpio19";
+			function = "gsbi5_uart";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	reset_out_pins: reset-out-state {
+		reset-out-pins {
+			pins = "gpio66";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+};
+
+&pmicgpio {
+	usb_vbus_5v_pins: usb-vbus-5v-state {
+		pins = "gpio4";
+		function = "normal";
+		output-high;
+		bias-disable;
+		qcom,drive-strength = <1>;
+		power-source = <2>;
+	};
+};
+
+&gsbi3 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_SPI>;
+};
+
+&gsbi3_spi {
+	status = "okay";
+	pinctrl-0 = <&gsbi3_pins>;
+	pinctrl-names = "default";
+	assigned-clocks = <&gcc GSBI3_QUP_CLK>;
+	assigned-clock-rates = <24000000>;
+};
+
+&gsbi4 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+};
+
+&gsbi4_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi4_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi5_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&gsbi5_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi5_uart_pins>;
+	pinctrl-names = "default";
+};
+
+&sdcc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
new file mode 100644
index 000000000000..b40c52ddf9b4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -0,0 +1,507 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm MDM9615 SoC
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-mdm9615.h>
+#include <dt-bindings/reset/qcom,gcc-mdm9615.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MDM9615";
+	compatible = "qcom,mdm9615";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a5";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+		};
+	};
+
+	cpu-pmu {
+		compatible = "arm,cortex-a5-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	clocks {
+		cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+	};
+
+	regulators {
+		vsdcc_fixed: vsdcc-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "SDCC Power";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-always-on;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		L2: cache-controller@2040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x02040000 0x1000>;
+			arm,data-latency = <2 2 0>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-mdm9615", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			cpu-offset = <0x80000>;
+		};
+
+		msmgpio: pinctrl@800000 {
+			compatible = "qcom,mdm9615-pinctrl";
+			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 88>;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x800000 0x4000>;
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-mdm9615";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-mdm9615";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-mdm9615", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+			assigned-clocks = <&gcc PRNG_CLK>;
+			assigned-clock-rates = <32000000>;
+		};
+
+		gsbi2: gsbi@16100000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x16100000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi2_i2c: i2c@16180000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16180000 0x1000>;
+				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <3>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi3_spi: spi@16280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x100>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x1000>,
+				      <0x16300000 0x1000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi5: gsbi@16400000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x16400000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_i2c: i2c@16480000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16480000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				/* QUP clock is not initialized, set rate */
+				assigned-clocks = <&gcc GSBI5_QUP_CLK>;
+				assigned-clock-rates = <24000000>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi5_serial: serial@16440000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16440000 0x1000>,
+				      <0x16400000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		qcom,ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+
+			pmicintc: pmic {
+				compatible = "qcom,pm8018", "qcom,pm8921";
+				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pwrkey@1c {
+					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
+					reg = <0x1c>;
+					interrupt-parent = <&pmicintc>;
+					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+						     <51 IRQ_TYPE_EDGE_RISING>;
+					debounce = <15625>;
+					pull-up;
+				};
+
+				pmicmpp: mpps@50 {
+					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					reg = <0x50>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pmicmpp 0 0 6>;
+				};
+
+				rtc@11d {
+					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
+					interrupt-parent = <&pmicintc>;
+					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+					reg = <0x11d>;
+					allow-set-time;
+				};
+
+				pmicgpio: gpio@150 {
+					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
+					reg = <0x150>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					gpio-ranges = <&pmicgpio 0 0 6>;
+					#gpio-cells = <2>;
+				};
+			};
+		};
+
+		sdcc1bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc2bam: dma-controller@12142000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12142000 0x8000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1: mmc@12180000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <48000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC1_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		sdcc2: mmc@12140000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12140000 0x2000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC2_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-mdm9615", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-mdm9615";
+			reg = <0x108000 0x1000>;
+
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			regulators {
+				compatible = "qcom,rpm-pm8018-regulators";
+
+				vin_lvs1-supply = <&pm8018_s3>;
+
+				vdd_l7-supply = <&pm8018_s4>;
+				vdd_l8-supply = <&pm8018_s3>;
+				vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
+
+				/* Buck SMPS */
+				pm8018_s1: s1 {
+					regulator-min-microvolt = <500000>;
+					regulator-max-microvolt = <1150000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				pm8018_s2: s2 {
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				pm8018_s3: s3 {
+					regulator-always-on;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				pm8018_s4: s4 {
+					regulator-min-microvolt = <2100000>;
+					regulator-max-microvolt = <2200000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				pm8018_s5: s5 {
+					regulator-always-on;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				/* PMOS LDO */
+				pm8018_l2: l2 {
+					regulator-always-on;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				pm8018_l3: l3 {
+					regulator-always-on;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				pm8018_l4: l4 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+
+				pm8018_l5: l5 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+
+				pm8018_l6: l6 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+
+				pm8018_l7: l7 {
+					regulator-min-microvolt = <1850000>;
+					regulator-max-microvolt = <1900000>;
+					bias-pull-down;
+				};
+
+				pm8018_l8: l8 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				pm8018_l9: l9 {
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1150000>;
+					bias-pull-down;
+				};
+
+				pm8018_l10: l10 {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				pm8018_l11: l11 {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				pm8018_l12: l12 {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				pm8018_l13: l13 {
+					regulator-min-microvolt = <1850000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				pm8018_l14: l14 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+
+				/* Low Voltage Switch */
+				pm8018_lvs1: lvs1 {
+					bias-pull-down;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
new file mode 100644
index 000000000000..288cacd5d1fa
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include "qcom-msm8226.dtsi"
+
+/ {
+	model = "Samsung Galaxy S III Neo";
+	compatible = "samsung,s3ve3g", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
new file mode 100644
index 000000000000..313a726f4704
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
@@ -0,0 +1,857 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	chosen { };
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8226", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		smem_region: smem@3000000 {
+			reg = <0x3000000 0x100000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8226";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8226", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8226-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <1>;
+						};
+						rpmpd_opp_svs_krait: opp2 {
+							opp-level = <2>;
+						};
+						rpmpd_opp_svs_soc: opp3 {
+							opp-level = <3>;
+						};
+						rpmpd_opp_nom: opp4 {
+							opp-level = <4>;
+						};
+						rpmpd_opp_turbo: opp5 {
+							opp-level = <5>;
+						};
+						rpmpd_opp_super_turbo: opp6 {
+							opp-level = <6>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		memory-region = <&smem_region>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc1_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc2_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc3_default_state>;
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart3: serial@f991f000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991f000 0x1000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart4: serial@f9920000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf9920000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c1_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c2_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c3_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c4: i2c@f9926000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9926000 0x1000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c4_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c5: i2c@f9927000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9927000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c5_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8226-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <400000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8226",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+						 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					qcom,init-seq = /bits/ 8 <0x0 0x44
+						0x1 0x68 0x2 0x24 0x3 0x13>;
+				};
+			};
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8226";
+			reg = <0xfc400000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&sleep_clk>;
+			clock-names = "xo",
+				      "sleep_clk";
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8226";
+			reg = <0xfd8c0000 0x6000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
+				 <&gcc GPLL0_VOTE>,
+				 <&gcc GPLL1_VOTE>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "mmss_gpll0_vote",
+				      "gpll0_vote",
+				      "gpll1_vote",
+				      "gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte";
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8226-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 117>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			blsp1_i2c1_pins: blsp1-i2c1-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_pins: blsp1-i2c2-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_pins: blsp1-i2c3-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c4_pins: blsp1-i2c4-state {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c5_pins: blsp1-i2c5-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_default: cci-default-state {
+				pins = "gpio29", "gpio30";
+				function = "cci_i2c0";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_sleep: cci-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdhc1_default_state: sdhc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc1_cmd", "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc2_default_state: sdhc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc2_cmd", "sdc2_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc3_default_state: sdhc3-default-state {
+				clk-pins {
+					pins = "gpio44";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "gpio43";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "gpio39", "gpio40", "gpio41", "gpio42";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8226-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2";
+			#qcom,sensors = <6>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,msm8226-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@1c1 {
+				reg = <0x1c1 0x2>;
+				bits = <5 8>;
+			};
+
+			tsens_s0_p1: s0-p1@1c2 {
+				reg = <0x1c2 0x2>;
+				bits = <5 6>;
+			};
+
+			tsens_s1_p1: s1-p1@1c4 {
+				reg = <0x1c4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p1: s2-p1@1c4 {
+				reg = <0x1c4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p1: s3-p1@1c5 {
+				reg = <0x1c5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p1: s4-p1@1c6 {
+				reg = <0x1c6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p1: s5-p1@1c7 {
+				reg = <0x1c7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s6_p1: s6-p1@1ca {
+				reg = <0x1ca 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2: base2@1cc {
+				reg = <0x1cc 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p2: s0-p2@1cd {
+				reg = <0x1cd 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p2: s1-p2@1cd {
+				reg = <0x1cd 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p2: s2-p2@1ce {
+				reg = <0x1ce 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p2: s3-p2@1cf {
+				reg = <0x1cf 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p2: s4-p2@446 {
+				reg = <0x446 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@447 {
+				reg = <0x447 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@44e {
+				reg = <0x44e 0x1>;
+				bits = <1 6>;
+			};
+
+			tsens_mode: mode@44f {
+				reg = <0x44f 0x1>;
+				bits = <5 3>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		rng@f9bff000 {
+			compatible = "qcom,prng";
+			reg = <0xf9bff000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		timer@f9020000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,msm8226-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8226-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8226-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8226_VDDCX>;
+			power-domain-names = "cx";
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+
+				label = "lpass";
+			};
+		};
+
+		sram@fe805000 {
+			compatible = "qcom,msm8226-imem", "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-bootloader = <0x77665500>;
+				mode-normal     = <0x77665501>;
+				mode-recovery   = <0x77665502>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
new file mode 100644
index 000000000000..be18f1be29a1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8660.dtsi"
+
+/ {
+	model = "Qualcomm MSM8660 SURF";
+	compatible = "qcom,msm8660-surf", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	status = "okay";
+};
+
+&pm8058 {
+	keypad@148 {
+		linux,keymap = <
+			MATRIX_KEY(0, 0, KEY_FN_F1)
+			MATRIX_KEY(0, 1, KEY_UP)
+			MATRIX_KEY(0, 2, KEY_LEFT)
+			MATRIX_KEY(0, 3, KEY_VOLUMEUP)
+			MATRIX_KEY(1, 0, KEY_FN_F2)
+			MATRIX_KEY(1, 1, KEY_RIGHT)
+			MATRIX_KEY(1, 2, KEY_DOWN)
+			MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
+			MATRIX_KEY(2, 3, KEY_ENTER)
+			MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
+			MATRIX_KEY(4, 1, KEY_UP)
+			MATRIX_KEY(4, 2, KEY_LEFT)
+			MATRIX_KEY(4, 3, KEY_HOME)
+			MATRIX_KEY(4, 4, KEY_FN_F3)
+			MATRIX_KEY(5, 0, KEY_CAMERA)
+			MATRIX_KEY(5, 1, KEY_RIGHT)
+			MATRIX_KEY(5, 2, KEY_DOWN)
+			MATRIX_KEY(5, 3, KEY_BACK)
+			MATRIX_KEY(5, 4, KEY_MENU)
+			>;
+		keypad,num-rows = <6>;
+		keypad,num-columns = <5>;
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
new file mode 100644
index 000000000000..78023ed2fdf7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -0,0 +1,651 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8660.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MSM8660";
+	compatible = "qcom,msm8660";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "qcom,scorpion";
+			enable-method = "qcom,gcc-msm8660";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@1 {
+			compatible = "qcom,scorpion";
+			enable-method = "qcom,gcc-msm8660";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	cpu-pmu {
+		compatible = "qcom,scorpion-mp-pmu";
+		interrupts = <1 9 0x304>;
+	};
+
+	clocks {
+		cxo_board: cxo-board-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
+		};
+
+		pxo_board: pxo-board-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
+		};
+
+		sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
+		};
+	};
+
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&xoadc 0x00 0x01>, /* Battery */
+			    <&xoadc 0x00 0x02>, /* DC in (charger) */
+			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
+			    <&xoadc 0x00 0x0b>, /* Die temperature */
+			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			    <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@2080000 {
+			compatible = "qcom,msm-8660-qgic";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = < 0x02080000 0x1000 >,
+			      < 0x02081000 0x1000 >;
+		};
+
+		timer@2000000 {
+			compatible = "qcom,scss-timer", "qcom,msm-timer";
+			interrupts = <1 0 0x301>,
+				     <1 1 0x301>,
+				     <1 2 0x301>;
+			reg = <0x02000000 0x100>;
+			clock-frequency = <27000000>,
+					  <32768>;
+			cpu-offset = <0x40000>;
+		};
+
+		tlmm: pinctrl@800000 {
+			compatible = "qcom,msm8660-pinctrl";
+			reg = <0x800000 0x4000>;
+
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 173>;
+			#gpio-cells = <2>;
+			interrupts = <0 16 0x4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-msm8660";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+			status = "disabled";
+
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi6: gsbi@16500000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16500000 0x100>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi6_serial: serial@16540000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16540000 0x1000>,
+				      <0x16500000 0x1000>;
+				interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi8: gsbi@19800000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x19800000 0x100>;
+			clocks = <&gcc GSBI8_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+			status = "disabled";
+
+			gsbi8_i2c: i2c@19880000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x19880000 0x1000>;
+				interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI8_QUP_CLK>, <&gcc GSBI8_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi12: gsbi@19c00000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x19c00000 0x100>;
+			clocks = <&gcc GSBI12_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi12_serial: serial@19c40000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x19c40000 0x1000>,
+				      <0x19c00000 0x1000>;
+				interrupts = <0 195 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi12_i2c: i2c@19c80000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x19c80000 0x1000>;
+				interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		ebi2: external-bus@1a100000 {
+			compatible = "qcom,msm8660-ebi2";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0x1a800000 0x00800000>,
+				 <1 0x0 0x1b000000 0x00800000>,
+				 <2 0x0 0x1b800000 0x00800000>,
+				 <3 0x0 0x1d000000 0x08000000>,
+				 <4 0x0 0x1c800000 0x00800000>,
+				 <5 0x0 0x1c000000 0x00800000>;
+			reg = <0x1a100000 0x1000>, <0x1a110000 0x1000>;
+			reg-names = "ebi2", "xmem";
+			clocks = <&gcc EBI2_2X_CLK>, <&gcc EBI2_CLK>;
+			clock-names = "ebi2x", "ebi2";
+			status = "disabled";
+		};
+
+		ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+
+			pm8058: pmic {
+				compatible = "qcom,pm8058";
+				interrupt-parent = <&tlmm>;
+				interrupts = <88 8>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pm8058_gpio: gpio@150 {
+					compatible = "qcom,pm8058-gpio",
+						     "qcom,ssbi-gpio";
+					reg = <0x150>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					gpio-ranges = <&pm8058_gpio 0 0 44>;
+					#gpio-cells = <2>;
+
+				};
+
+				pm8058_mpps: mpps@50 {
+					compatible = "qcom,pm8058-mpp",
+						     "qcom,ssbi-mpp";
+					reg = <0x50>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&pm8058_mpps 0 0 12>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				pwrkey@1c {
+					compatible = "qcom,pm8058-pwrkey";
+					reg = <0x1c>;
+					interrupt-parent = <&pm8058>;
+					interrupts = <50 1>, <51 1>;
+					debounce = <15625>;
+					pull-up;
+				};
+
+				pm8058_keypad: keypad@148 {
+					compatible = "qcom,pm8058-keypad";
+					reg = <0x148>;
+					interrupt-parent = <&pm8058>;
+					interrupts = <74 1>, <75 1>;
+					debounce = <15>;
+					scan-delay = <32>;
+					row-hold = <91500>;
+				};
+
+				xoadc: xoadc@197 {
+					compatible = "qcom,pm8058-adc";
+					reg = <0x197>;
+					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+					#io-channel-cells = <2>;
+
+					vcoin: adc-channel@0 {
+						reg = <0x00 0x00>;
+					};
+					vbat: adc-channel@1 {
+						reg = <0x00 0x01>;
+					};
+					dcin: adc-channel@2 {
+						reg = <0x00 0x02>;
+					};
+					ichg: adc-channel@3 {
+						reg = <0x00 0x03>;
+					};
+					vph_pwr: adc-channel@4 {
+						reg = <0x00 0x04>;
+					};
+					usb_vbus: adc-channel@a {
+						reg = <0x00 0x0a>;
+					};
+					die_temp: adc-channel@b {
+						reg = <0x00 0x0b>;
+					};
+					ref_625mv: adc-channel@c {
+						reg = <0x00 0x0c>;
+					};
+					ref_1250mv: adc-channel@d {
+						reg = <0x00 0x0d>;
+					};
+					ref_325mv: adc-channel@e {
+						reg = <0x00 0x0e>;
+					};
+					ref_muxoff: adc-channel@f {
+						reg = <0x00 0x0f>;
+					};
+				};
+
+				rtc@1e8 {
+					compatible = "qcom,pm8058-rtc";
+					reg = <0x1e8>;
+					interrupt-parent = <&pm8058>;
+					interrupts = <39 1>;
+					allow-set-time;
+				};
+
+				vibrator@4a {
+					compatible = "qcom,pm8058-vib";
+					reg = <0x4a>;
+				};
+
+				pm8058_led48: led@48 {
+					compatible = "qcom,pm8058-keypad-led";
+					reg = <0x48>;
+					status = "disabled";
+				};
+
+				pm8058_led131: led@131 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x131>;
+					status = "disabled";
+				};
+
+				pm8058_led132: led@132 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x132>;
+					status = "disabled";
+				};
+
+				pm8058_led133: led@133 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x133>;
+					status = "disabled";
+				};
+
+			};
+		};
+
+		l2cc: clock-controller@2082000 {
+			compatible = "qcom,kpss-gcc-msm8660", "qcom,kpss-gcc", "syscon";
+			reg = <0x02082000 0x1000>;
+		};
+
+		rpm: rpm@104000 {
+			compatible = "qcom,rpm-msm8660";
+			reg = <0x00104000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-msm8660", "qcom,rpmcc";
+				#clock-cells = <1>;
+				clocks = <&pxo_board>;
+				clock-names = "pxo";
+			};
+
+			regulators-0 {
+				compatible = "qcom,rpm-pm8901-regulators";
+
+				pm8901_l0: l0 {};
+				pm8901_l1: l1 {};
+				pm8901_l2: l2 {};
+				pm8901_l3: l3 {};
+				pm8901_l4: l4 {};
+				pm8901_l5: l5 {};
+				pm8901_l6: l6 {};
+
+				/* S0 and S1 Handled as SAW regulators by SPM */
+				pm8901_s2: s2 {};
+				pm8901_s3: s3 {};
+				pm8901_s4: s4 {};
+
+				pm8901_lvs0: lvs0 {};
+				pm8901_lvs1: lvs1 {};
+				pm8901_lvs2: lvs2 {};
+				pm8901_lvs3: lvs3 {};
+
+				pm8901_mvs: mvs {};
+			};
+
+			regulators-1 {
+				compatible = "qcom,rpm-pm8058-regulators";
+
+				pm8058_l0: l0 {};
+				pm8058_l1: l1 {};
+				pm8058_l2: l2 {};
+				pm8058_l3: l3 {};
+				pm8058_l4: l4 {};
+				pm8058_l5: l5 {};
+				pm8058_l6: l6 {};
+				pm8058_l7: l7 {};
+				pm8058_l8: l8 {};
+				pm8058_l9: l9 {};
+				pm8058_l10: l10 {};
+				pm8058_l11: l11 {};
+				pm8058_l12: l12 {};
+				pm8058_l13: l13 {};
+				pm8058_l14: l14 {};
+				pm8058_l15: l15 {};
+				pm8058_l16: l16 {};
+				pm8058_l17: l17 {};
+				pm8058_l18: l18 {};
+				pm8058_l19: l19 {};
+				pm8058_l20: l20 {};
+				pm8058_l21: l21 {};
+				pm8058_l22: l22 {};
+				pm8058_l23: l23 {};
+				pm8058_l24: l24 {};
+				pm8058_l25: l25 {};
+
+				pm8058_s0: s0 {};
+				pm8058_s1: s1 {};
+				pm8058_s2: s2 {};
+				pm8058_s3: s3 {};
+				pm8058_s4: s4 {};
+
+				pm8058_lvs0: lvs0 {};
+				pm8058_lvs1: lvs1 {};
+
+				pm8058_ncp: ncp {};
+			};
+		};
+
+		amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x8000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+			};
+
+			sdcc2: mmc@12140000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12140000 0x8000>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+			};
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x8000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <48000000>;
+				no-1-8-v;
+			};
+
+			sdcc4: mmc@121c0000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x121c0000 0x8000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				max-frequency = <48000000>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+			};
+
+			sdcc5: mmc@12200000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12200000 0x8000>;
+				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <48000000>;
+			};
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-msm8660", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+	};
+
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
new file mode 100644
index 000000000000..c8d34de8a71e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e5.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
new file mode 100644
index 000000000000..85be286c8608
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e7.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
new file mode 100644
index 000000000000..d3abe0536238
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-grandmax.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
new file mode 100644
index 000000000000..dee2c20af355
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-serranove.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
new file mode 100644
index 000000000000..36328dbe4212
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/ {
+	cpus {
+		cpu@0 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@1 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@2 {
+			enable-method = "qcom,msm8916-smp";
+		};
+		cpu@3 {
+			enable-method = "qcom,msm8916-smp";
+		};
+
+		idle-states {
+			/delete-property/ entry-method;
+		};
+	};
+
+	psci {
+		status = "disabled";
+	};
+};
+
+&CPU_SLEEP_0 {
+	compatible = "qcom,idle-state-spc";
+};
+
+&cpu0_acc {
+	status = "okay";
+};
+
+&cpu0_saw {
+	status = "okay";
+};
+
+&cpu1_acc {
+	status = "okay";
+};
+
+&cpu1_saw {
+	status = "okay";
+};
+
+&cpu2_acc {
+	status = "okay";
+};
+
+&cpu2_saw {
+	status = "okay";
+};
+
+&cpu3_acc {
+	status = "okay";
+};
+
+&cpu3_saw {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
new file mode 100644
index 000000000000..6c1bc3818883
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8960.dtsi"
+
+/ {
+	model = "Qualcomm MSM8960 CDP";
+	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ext_l2: gpio-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ext_l2";
+		gpio = <&msmgpio 91 0>;
+		startup-delay-us = <10000>;
+		enable-active-high;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_default>;
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+
+	ethernet@0 {
+		compatible = "micrel,ks8851";
+		reg = <0>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <90 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <5400000>;
+		vdd-supply = <&ext_l2>;
+		vdd-io-supply = <&pm8921_lvs6>;
+		reset-gpios = <&msmgpio 89 0>;
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		 mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		 };
+
+		 clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+	};
+};
+
+&pmicintc {
+	keypad@148 {
+		linux,keymap = <
+			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+			MATRIX_KEY(0, 3, KEY_CAMERA)
+			>;
+		keypad,num-rows = <1>;
+		keypad,num-columns = <5>;
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..13e85c287498
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8960.dtsi"
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+
+/ {
+	model = "Samsung Galaxy Express SGH-I437";
+	compatible = "samsung,expressatt", "qcom,msm8960";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+		mmc0 = &sdcc1; /* SDCC1 eMMC slot */
+		mmc1 = &sdcc3; /* SDCC3 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	vqmmc-supply = <&pm8921_l7>;
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-0 = <&spi1_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		};
+
+		clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3100000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
new file mode 100644
index 000000000000..fa2013388d99
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -0,0 +1,407 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MSM8960";
+	compatible = "qcom,msm8960";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_PPI 14 0x304>;
+
+		cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+		};
+
+		cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 10 0x304>;
+		qcom,no-pc-write;
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
+		};
+
+		pxo_board: pxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
+		};
+	};
+
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-msm8960", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 0x301>,
+				     <GIC_PPI 2 0x301>,
+				     <GIC_PPI 3 0x301>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			cpu-offset = <0x80000>;
+		};
+
+		msmgpio: pinctrl@800000 {
+			compatible = "qcom,msm8960-pinctrl";
+			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 152>;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x800000 0x4000>;
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-msm8960";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-msm8960";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
+		};
+
+		clock-controller@4000000 {
+			compatible = "qcom,mmcc-msm8960";
+			reg = <0x4000000 0x1000>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-msm8960";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			regulators {
+				compatible = "qcom,rpm-pm8921-regulators";
+			};
+		};
+
+		acc0: clock-controller@2088000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		acc1: clock-controller@2098000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: regulator@2089000 {
+			compatible = "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		saw1: regulator@2099000 {
+			compatible = "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
+		gsbi5: gsbi@16400000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x16400000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_serial: serial@16440000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16440000 0x1000>,
+				      <0x16400000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+
+			pmicintc: pmic {
+				compatible = "qcom,pm8921";
+				interrupt-parent = <&msmgpio>;
+				interrupts = <104 IRQ_TYPE_LEVEL_LOW>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				pwrkey@1c {
+					compatible = "qcom,pm8921-pwrkey";
+					reg = <0x1c>;
+					interrupt-parent = <&pmicintc>;
+					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
+						     <51 IRQ_TYPE_EDGE_RISING>;
+					debounce = <15625>;
+					pull-up;
+				};
+
+				keypad@148 {
+					compatible = "qcom,pm8921-keypad";
+					reg = <0x148>;
+					interrupt-parent = <&pmicintc>;
+					interrupts = <74 IRQ_TYPE_EDGE_RISING>,
+						     <75 IRQ_TYPE_EDGE_RISING>;
+					debounce = <15>;
+					scan-delay = <32>;
+					row-hold = <91500>;
+				};
+
+				rtc@11d {
+					compatible = "qcom,pm8921-rtc";
+					interrupt-parent = <&pmicintc>;
+					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
+					reg = <0x11d>;
+					allow-set-time;
+				};
+			};
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x8000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+		};
+
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x8000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-msm8960", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <1>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				spi-max-frequency = <24000000>;
+				cs-gpios = <&msmgpio 8 0>;
+
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		usb1: usb@12500000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			#reset-cells = <1>;
+			status = "disabled";
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8960",
+						     "qcom,usb-hs-phy";
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+					#phy-cells = <0>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
new file mode 100644
index 000000000000..60bdfddeae69
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -0,0 +1,696 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "LGE MSM 8974 HAMMERHEAD";
+	compatible = "lge,hammerhead", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp2_uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	clk_pwm: pwm {
+		compatible = "clk-pwm";
+		clocks = <&mmcc CAMSS_GP1_CLK>;
+
+		pinctrl-0 = <&vibrator_pin>;
+		pinctrl-names = "default";
+
+		#pwm-cells = <2>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+		pwms = <&clk_pwm 0 100000>;
+		pwm-names = "enable";
+
+		vcc-supply = <&pm8941_l19>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	charger: bq24192@6b {
+		compatible = "ti,bq24192";
+		reg = <0x6b>;
+		interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+		omit-battery-class;
+
+		usb_otg_vbus: usb-otg-vbus { };
+	};
+
+	fuelgauge: max17048@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x4d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+
+		maxim,alert-low-soc-level = <2>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@70 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x70>;
+
+		interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	avago_apds993@39 {
+		compatible = "avago,apds9930";
+		reg = <0x39>;
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l17>;
+		vddio-supply = <&pm8941_lvs1>;
+		led-max-microamp = <100000>;
+		amstaos,proximity-diodes = <0>;
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	led-controller@38 {
+		compatible = "ti,lm3630a";
+		status = "okay";
+		reg = <0x38>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <200>;
+		};
+	};
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	mpu6515@68 {
+		compatible = "invensense,mpu6515";
+		reg = <0x68>;
+		interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
+		vddio-supply = <&pm8941_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6515_pin>;
+
+		mount-matrix = "0", "-1", "0",
+				"-1", "0", "0",
+				"0", "0", "1";
+
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ak8963@f {
+				compatible = "asahi-kasei,ak8963";
+				reg = <0x0f>;
+				gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+				vid-supply = <&pm8941_lvs1>;
+				vdd-supply = <&pm8941_l17>;
+			};
+
+			bmp280@76 {
+				compatible = "bosch,bmp280";
+				reg = <0x76>;
+				vdda-supply = <&pm8941_lvs1>;
+				vddd-supply = <&pm8941_l17>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+};
+
+&blsp2_uart4 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pin>;
+
+		host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_lvs3>;
+	vddio-supply = <&pm8941_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "lg,acx467akm-7";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_pin>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio9";
+		function = "normal";
+
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio17";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	otg {
+		gpio-hog;
+		gpios = <35 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "otg-gpio";
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <815000>;
+			regulator-max-microvolt = <900000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8941_s3>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	mpu6515_pin: mpu6515-state {
+		pins = "gpio73";
+		function = "gpio";
+		bias-disable;
+	};
+
+	touch_pin: touch-state {
+		int-pins {
+			pins = "gpio5";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		reset-pins {
+			pins = "gpio8";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	panel_pin: panel-state {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bt_pin: bt-state {
+		hostwake-pins {
+			pins = "gpio42";
+			function = "gpio";
+		};
+
+		devwake-pins {
+			pins = "gpio62";
+			function = "gpio";
+		};
+
+		shutdown-pins {
+			pins = "gpio41";
+			function = "gpio";
+		};
+	};
+
+	vibrator_pin: vibrator-state {
+		core-pins {
+			pins = "gpio27";
+			function = "gp1_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		enable-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	extcon = <&charger>, <&usb_id>;
+	vbus-supply = <&usb_otg_vbus>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
new file mode 100644
index 000000000000..9f2ab5c122d0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1 Compact";
+	compatible = "sony,xperia-amami", "qcom,msm8974";
+	chassis-type = "handset";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1300000>;
+	qcom,fast-charge-current-limit = <1300000>;
+	qcom,dc-current-limit = <1300000>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
new file mode 100644
index 000000000000..9028f17e5c4a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1";
+	compatible = "sony,xperia-honami", "qcom,msm8974";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
new file mode 100644
index 000000000000..68a2f9094e53
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -0,0 +1,495 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@3e8e0000 {
+			compatible = "ramoops";
+			reg = <0x3e8e0000 0x200000>;
+
+			console-size = <0x100000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x80000>;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <10>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			touchscreen-inverted-x;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	nfc@28 {
+		compatible = "nxp,pn544-i2c";
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <59 IRQ_TYPE_EDGE_RISING>;
+
+		enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	/* sii8334 MHL HDMI bridge */
+};
+
+&pm8941_coincell {
+	status = "okay";
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio4", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&pm8941_wled {
+	status = "okay";
+
+	qcom,cs-out;
+	qcom,current-limit = <20>;
+	qcom,current-boost-limit = <805>;
+	qcom,switching-freq = <1600>;
+	qcom,ovp = <29>;
+	qcom,num-strings = <2>;
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+};
+
+&tlmm {
+	ts_int_pin: touch-int-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
new file mode 100644
index 000000000000..aeca504918a0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -0,0 +1,2406 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interconnect/qcom,msm8974.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_PPI 9 0xf04>;
+
+		CPU0: cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU1: cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU2: cpu@2 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		CPU3: cpu@3 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v2";
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&L2>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			cpu-idle-states = <&CPU_SPC>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+			qcom,saw = <&saw_l2>;
+		};
+
+		idle-states {
+			CPU_SPC: spc {
+				compatible = "qcom,idle-state-spc",
+						"arm,idle-state";
+				entry-latency-us = <150>;
+				exit-latency-us = <200>;
+				min-residency-us = <2000>;
+			};
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8974", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 7 0xf04>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x5100000>;
+			no-map;
+		};
+
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x100000>;
+			no-map;
+		};
+
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0xa00000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
+
+		venus_region: memory@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0xfa00000 0x200000>;
+			no-map;
+		};
+
+		tz_region: memory@fc00000 {
+			reg = <0x0fc00000 0x160000>;
+			no-map;
+		};
+
+		rfsa_mem: memory@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		memory-region = <&smem_region>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-wcnss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 8 13>;
+		qcom,ipc-2 = <&apcs 8 9>;
+		qcom,ipc-3 = <&apcs 8 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smsm: modem@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		adsp_smsm: adsp@2 {
+			reg = <2>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@7 {
+			reg = <7>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8974";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+			};
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+		};
+
+		apcs: syscon@f9011000 {
+			compatible = "syscon";
+			reg = <0xf9011000 0x1000>;
+		};
+
+		timer@f9020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		saw0: power-controller@f9089000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw1: power-controller@f9099000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw2: power-controller@f90a9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw3: power-controller@f90b9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
+		};
+
+		saw_l2: power-controller@f9012000 {
+			compatible = "qcom,saw2";
+			reg = <0xf9012000 0x1000>;
+			regulator;
+		};
+
+		acc0: power-manager@f9088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		acc1: power-manager@f9098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		acc2: power-manager@f90a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		acc3: power-manager@f90b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <8>;
+			non-removable;
+
+			status = "disabled";
+		};
+
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@f991e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991e000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c1_default>;
+			pinctrl-1 = <&blsp1_i2c1_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c2_default>;
+			pinctrl-1 = <&blsp1_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c3_default>;
+			pinctrl-1 = <&blsp1_i2c3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c6_default>;
+			pinctrl-1 = <&blsp1_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_dma: dma-controller@f9944000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xf9944000 0x19000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp2_uart1: serial@f995d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf995d000 0x1000>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart1_default>;
+			pinctrl-1 = <&blsp2_uart1_sleep>;
+			status = "disabled";
+		};
+
+		blsp2_uart2: serial@f995e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf995e000 0x1000>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp2_uart4: serial@f9960000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf9960000 0x1000>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_UART4_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_uart4_default>;
+			status = "disabled";
+		};
+
+		blsp2_i2c2: i2c@f9964000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9964000 0x1000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c2_default>;
+			pinctrl-1 = <&blsp2_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c5: i2c@f9967000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9967000 0x1000>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c5_default>;
+			pinctrl-1 = <&blsp2_i2c5_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp2_i2c6: i2c@f9968000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9968000 0x1000>;
+			interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c6_default>;
+			pinctrl-1 = <&blsp2_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs1_phy: phy-0 {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+
+				usb_hs2_phy: phy-1 {
+					compatible = "qcom,usb-hs-phy-msm8974",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2B_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2B_PHY_BCR>, <&usb 1>;
+					reset-names = "phy", "por";
+					status = "disabled";
+				};
+			};
+		};
+
+		rng@f9bff000 {
+			compatible = "qcom,prng";
+			reg = <0xf9bff000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		pronto: remoteproc@fb204000 {
+			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+			reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+			reg-names = "ccu", "dxe", "pmu";
+
+			memory-region = <&wcnss_region>;
+
+			interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			iris {
+				compatible = "qcom,wcn3680";
+
+				clocks = <&rpmcc RPM_SMD_CXO_A2>;
+				clock-names = "xo";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 17>;
+				qcom,smd-edge = <6>;
+
+				wcnss {
+					compatible = "qcom,wcnss";
+					qcom,smd-channels = "WCNSS_CTRL";
+					status = "disabled";
+
+					qcom,mmio = <&pronto>;
+
+					bluetooth {
+						compatible = "qcom,wcnss-bt";
+					};
+
+					wifi {
+						compatible = "qcom,wcnss-wlan";
+
+						interrupts = <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>,
+							     <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>;
+						interrupt-names = "tx", "rx";
+
+						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
+					};
+				};
+			};
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,msm8974-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		etf@fc307000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0xfc307000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint = <&replicator_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					etf_in: endpoint {
+						remote-endpoint = <&merger_out>;
+					};
+				};
+			};
+		};
+
+		tpiu@fc318000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0xfc318000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					tpiu_in: endpoint {
+						remote-endpoint = <&replicator_out1>;
+					};
+				 };
+			};
+		};
+
+		funnel@fc31a000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc31a000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 0 - not-connected
+				 * 1 - connected trought funnel to Multimedia CPU
+				 * 2 - connected to Wireless CPU
+				 * 3 - not-connected
+				 * 4 - not-connected
+				 * 6 - not-connected
+				 * 7 - connected to STM
+				 */
+				port@5 {
+					reg = <5>;
+					funnel1_in5: endpoint {
+						remote-endpoint = <&kpss_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					funnel1_out: endpoint {
+						remote-endpoint = <&merger_in1>;
+					};
+				};
+			};
+		};
+
+		funnel@fc31b000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc31b000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * Not described input ports:
+				 * 0 - connected trought funnel to Audio, Modem and
+				 *     Resource and Power Manager CPU's
+				 * 2...7 - not-connected
+				 */
+				port@1 {
+					reg = <1>;
+					merger_in1: endpoint {
+						remote-endpoint = <&funnel1_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					merger_out: endpoint {
+						remote-endpoint = <&etf_in>;
+					};
+				};
+			};
+		};
+
+		replicator@fc31c000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0xfc31c000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			out-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint = <&tpiu_in>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
+					};
+				};
+			};
+		};
+
+		etr@fc322000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0xfc322000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				port {
+					etr_in: endpoint {
+						remote-endpoint = <&replicator_out0>;
+					};
+				};
+			};
+		};
+
+		etm@fc33c000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33c000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU0>;
+
+			out-ports {
+				port {
+					etm0_out: endpoint {
+						remote-endpoint = <&kpss_in0>;
+					};
+				};
+			};
+		};
+
+		etm@fc33d000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33d000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU1>;
+
+			out-ports {
+				port {
+					etm1_out: endpoint {
+						remote-endpoint = <&kpss_in1>;
+					};
+				};
+			};
+		};
+
+		etm@fc33e000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33e000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU2>;
+
+			out-ports {
+				port {
+					etm2_out: endpoint {
+						remote-endpoint = <&kpss_in2>;
+					};
+				};
+			};
+		};
+
+		etm@fc33f000 {
+			compatible = "arm,coresight-etm4x", "arm,primecell";
+			reg = <0xfc33f000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			cpu = <&CPU3>;
+
+			out-ports {
+				port {
+					etm3_out: endpoint {
+						remote-endpoint = <&kpss_in3>;
+					};
+				};
+			};
+		};
+
+		/* KPSS funnel, only 4 inputs are used */
+		funnel@fc345000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc345000 0x1000>;
+
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					kpss_in0: endpoint {
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					kpss_in1: endpoint {
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+					kpss_in2: endpoint {
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+				port@3 {
+					reg = <3>;
+					kpss_in3: endpoint {
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					kpss_out: endpoint {
+						remote-endpoint = <&funnel1_in5>;
+					};
+				};
+			};
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfc400000 0x4000>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&sleep_clk>;
+			clock-names = "xo",
+				      "sleep_clk";
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+		};
+
+		bimc: interconnect@fc380000 {
+			reg = <0xfc380000 0x6a000>;
+			compatible = "qcom,msm8974-bimc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+			         <&rpmcc RPM_SMD_BIMC_A_CLK>;
+		};
+
+		snoc: interconnect@fc460000 {
+			reg = <0xfc460000 0x4000>;
+			compatible = "qcom,msm8974-snoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+			         <&rpmcc RPM_SMD_SNOC_A_CLK>;
+		};
+
+		pnoc: interconnect@fc468000 {
+			reg = <0xfc468000 0x4000>;
+			compatible = "qcom,msm8974-pnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_PNOC_CLK>,
+			         <&rpmcc RPM_SMD_PNOC_A_CLK>;
+		};
+
+		ocmemnoc: interconnect@fc470000 {
+			reg = <0xfc470000 0x4000>;
+			compatible = "qcom,msm8974-ocmemnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+			         <&rpmcc RPM_SMD_OCMEMGX_A_CLK>;
+		};
+
+		mmssnoc: interconnect@fc478000 {
+			reg = <0xfc478000 0x4000>;
+			compatible = "qcom,msm8974-mmssnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&mmcc MMSS_S0_AXI_CLK>,
+			         <&mmcc MMSS_S0_AXI_CLK>;
+		};
+
+		cnoc: interconnect@fc480000 {
+			reg = <0xfc480000 0x4000>;
+			compatible = "qcom,msm8974-cnoc";
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_CNOC_CLK>,
+			         <&rpmcc RPM_SMD_CNOC_A_CLK>;
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_use_backup>,
+				      <&tsens_mode_backup>,
+				      <&tsens_base1_backup>, <&tsens_base2_backup>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>,
+				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "use_backup",
+					   "mode_backup",
+					   "base1_backup", "base2_backup",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2",
+					   "s0_p1_backup", "s0_p2_backup",
+					   "s1_p1_backup", "s1_p2_backup",
+					   "s2_p1_backup", "s2_p2_backup",
+					   "s3_p1_backup", "s3_p2_backup",
+					   "s4_p1_backup", "s4_p2_backup",
+					   "s5_p1_backup", "s5_p2_backup",
+					   "s6_p1_backup", "s6_p2_backup",
+					   "s7_p1_backup", "s7_p2_backup",
+					   "s8_p1_backup", "s8_p2_backup",
+					   "s9_p1_backup", "s9_p2_backup",
+					   "s10_p1_backup", "s10_p2_backup";
+			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,msm8974-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d2 {
+				reg = <0xd1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d2 {
+				reg = <0xd2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1: s5-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1: s7-p1@d6 {
+				reg = <0xd6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s8_p1: s8-p1@d7 {
+				reg = <0xd7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_mode: mode@d7 {
+				reg = <0xd7 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s9_p1: s9-p1@d8 {
+				reg = <0xd8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s10_p1: s10_p1@d8 {
+				reg = <0xd8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_base2: base2@d9 {
+				reg = <0xd9 0x2>;
+				bits = <4 8>;
+			};
+
+			tsens_s0_p2: s0-p2@da {
+				reg = <0xda 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@db {
+				reg = <0xdb 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p2: s2-p2@dc {
+				reg = <0xdc 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s3_p2: s3-p2@dc {
+				reg = <0xdc 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s4_p2: s4-p2@dd {
+				reg = <0xdd 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@de {
+				reg = <0xde 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@df {
+				reg = <0xdf 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@e0 {
+				reg = <0xe0 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s8_p2: s8-p2@e0 {
+				reg = <0xe0 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s9_p2: s9-p2@e1 {
+				reg = <0xe1 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10_p2@e2 {
+				reg = <0xe2 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p2_backup: s5-p2_backup@e3 {
+				reg = <0xe3 0x2>;
+				bits = <0 6>;
+			};
+
+			tsens_mode_backup: mode_backup@e3 {
+				reg = <0xe3 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s6_p2_backup: s6-p2_backup@e4 {
+				reg = <0xe4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2_backup: s7-p2_backup@e4 {
+				reg = <0xe4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p2_backup: s8-p2_backup@e5 {
+				reg = <0xe5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s9_p2_backup: s9-p2_backup@e6 {
+				reg = <0xe6 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s10_p2_backup: s10_p2_backup@e7 {
+				reg = <0xe7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_base1_backup: base1_backup@440 {
+				reg = <0x440 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1_backup: s0-p1_backup@441 {
+				reg = <0x441 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1_backup: s1-p1_backup@442 {
+				reg = <0x441 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1_backup: s2-p1_backup@442 {
+				reg = <0x442 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1_backup: s3-p1_backup@443 {
+				reg = <0x443 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1_backup: s4-p1_backup@444 {
+				reg = <0x444 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1_backup: s5-p1_backup@444 {
+				reg = <0x444 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1_backup: s6-p1_backup@445 {
+				reg = <0x445 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1_backup: s7-p1_backup@446 {
+				reg = <0x446 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_use_backup: use_backup@447 {
+				reg = <0x447 0x1>;
+				bits = <5 3>;
+			};
+
+			tsens_s8_p1_backup: s8-p1_backup@448 {
+				reg = <0x448 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p1_backup: s9-p1_backup@448 {
+				reg = <0x448 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1_backup: s10_p1_backup@449 {
+				reg = <0x449 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2_backup: base2_backup@44a {
+				reg = <0x44a 0x2>;
+				bits = <2 8>;
+			};
+
+			tsens_s0_p2_backup: s0-p2_backup@44b {
+				reg = <0x44b 0x3>;
+				bits = <2 6>;
+			};
+
+			tsens_s1_p2_backup: s1-p2_backup@44c {
+				reg = <0x44c 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2_backup: s2-p2_backup@44c {
+				reg = <0x44c 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p2_backup: s3-p2_backup@44d {
+				reg = <0x44d 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p2_backup: s4-p2_backup@44e {
+				reg = <0x44e 0x1>;
+				bits = <2 6>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@fc834000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xfc834000 0x7000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+		};
+
+		remoteproc_mss: remoteproc@fc880000 {
+			compatible = "qcom,msm8974-mss-pil";
+			reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "bus", "mem", "xo";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			qcom,halt-regs = <&tcsr_mutex 0x1180 0x1200 0x1280>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			mba {
+				memory-region = <&mba_region>;
+			};
+
+			mpss {
+				memory-region = <&mpss_region>;
+			};
+
+			bam_dmux: bam-dmux {
+				compatible = "qcom,bam-dmux";
+
+				interrupt-parent = <&modem_smsm>;
+				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
+				interrupt-names = "pc", "pc-ack";
+
+				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
+				qcom,smem-state-names = "pc", "pc-ack";
+
+				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
+				dma-names = "tx", "rx";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 12>;
+				qcom,smd-edge = <0>;
+
+				label = "modem";
+			};
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8974-tcsr-mutex", "qcom,tcsr-mutex", "syscon";
+			reg = <0xfd484000 0x2000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@fd4a0000 {
+			compatible = "qcom,tcsr-msm8974", "syscon";
+			reg = <0xfd4a0000 0x10000>;
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8974-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 146>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			sdc1_off: sdc1-off-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			sdc2_off: sdc2-off-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				cd-pins {
+					pins = "gpio54";
+					function = "gpio";
+					bias-disable;
+					drive-strength = <2>;
+				};
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default-state {
+				rx-pins {
+					pins = "gpio5";
+					function = "blsp_uart2";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				tx-pins {
+					pins = "gpio4";
+					function = "blsp_uart2";
+					drive-strength = <4>;
+					bias-disable;
+				};
+			};
+
+			blsp2_uart1_default: blsp2-uart1-default-state {
+				tx-rts-pins {
+					pins = "gpio41", "gpio44";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts-pins {
+					pins = "gpio42", "gpio43";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp2_uart1_sleep: blsp2-uart1-sleep-state {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			blsp2_uart4_default: blsp2-uart4-default-state {
+				tx-rts-pins {
+					pins = "gpio53", "gpio56";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts-pins {
+					pins = "gpio54", "gpio55";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp1_i2c1_default: blsp1-i2c1-default-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c1_sleep: blsp1-i2c1-sleep-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c2_default: blsp1-i2c2-default-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_sleep: blsp1-i2c2-sleep-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c3_default: blsp1-i2c3-default-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_sleep: blsp1-i2c3-sleep-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP1_I2C4 info is missing */
+
+			/* BLSP1_I2C5 info is missing */
+
+			blsp1_i2c6_default: blsp1-i2c6-default-state {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+			/* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */
+
+			/* BLSP2_I2C1 info is missing */
+
+			blsp2_i2c2_default: blsp2-i2c2-default-state {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c2_sleep: blsp2-i2c2-sleep-state {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP2_I2C3 info is missing */
+
+			/* BLSP2_I2C4 info is missing */
+
+			blsp2_i2c5_default: blsp2-i2c5-default-state {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c5_sleep: blsp2-i2c5-sleep-state {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp2_i2c6_default: blsp2-i2c6-default-state {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c6_sleep: blsp2-i2c6-sleep-state {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			cci_default: cci-default-state {
+				cci_i2c0_default: cci-i2c0-default-pins {
+					pins = "gpio19", "gpio20";
+					function = "cci_i2c0";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_default: cci-i2c1-default-pins {
+					pins = "gpio21", "gpio22";
+					function = "cci_i2c1";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			cci_sleep: cci-sleep-state {
+				cci_i2c0_sleep: cci-i2c0-sleep-pins {
+					pins = "gpio19", "gpio20";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cci_i2c1_sleep: cci-i2c1-sleep-pins {
+					pins = "gpio21", "gpio22";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+
+			spi8_default: spi8_default-state {
+				mosi-pins {
+					pins = "gpio45";
+					function = "blsp_spi8";
+				};
+				miso-pins {
+					pins = "gpio46";
+					function = "blsp_spi8";
+				};
+				cs-pins {
+					pins = "gpio47";
+					function = "blsp_spi8";
+				};
+				clk-pins {
+					pins = "gpio48";
+					function = "blsp_spi8";
+				};
+			};
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfd8c0000 0x6000>;
+			clocks = <&xo_board>,
+				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
+				 <&gcc GPLL0_VOTE>,
+				 <&gcc GPLL1_VOTE>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "mmss_gpll0_vote",
+				      "gpll0_vote",
+				      "gpll1_vote",
+				      "gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "hdmipll",
+				      "edp_link_clk",
+				      "edp_vco_div";
+		};
+
+		mdss: display-subsystem@fd900000 {
+			compatible = "qcom,mdss";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&mmcc MDSS_GDSC>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface", "bus", "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mdp: display-controller@fd900000 {
+				compatible = "qcom,msm8974-mdp5", "qcom,mdp5";
+				reg = <0xfd900100 0x22000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_VSYNC_CLK>;
+				clock-names = "iface", "bus", "core", "vsync";
+
+				interconnects = <&mmssnoc MNOC_MAS_MDP_PORT0 &bimc BIMC_SLV_EBI_CH0>;
+				interconnect-names = "mdp0-mem";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdp5_intf2_out: endpoint {
+							remote-endpoint = <&mdss_dsi1_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@fd922800 {
+				compatible = "qcom,msm8974-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922800 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi0_phy>;
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@fd922a00 {
+				compatible = "qcom,dsi-phy-28nm-hpm";
+				reg = <0xfd922a00 0xd4>,
+				      <0xfd922b00 0x280>,
+				      <0xfd922d80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@fd922e00 {
+				compatible = "qcom,msm8974-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922e00 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE1_CLK_SRC>, <&mmcc PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE1_CLK>,
+					 <&mmcc MDSS_PCLK1_CLK>,
+					 <&mmcc MDSS_ESC1_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi1_phy>;
+
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi1_in: endpoint {
+							remote-endpoint = <&mdp5_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@fd923000 {
+				compatible = "qcom,dsi-phy-28nm-hpm";
+				reg = <0xfd923000 0xd4>,
+				      <0xfd923100 0x280>,
+				      <0xfd923380 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+		};
+
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8974-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xfda0c000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <100000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gpu: adreno@fdb00000 {
+			compatible = "qcom,adreno-330.1", "qcom,adreno";
+			reg = <0xfdb00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+
+			clocks = <&mmcc OXILI_GFX3D_CLK>,
+				 <&mmcc OXILICX_AHB_CLK>,
+				 <&mmcc OXILICX_AXI_CLK>;
+			clock-names = "core", "iface", "mem_iface";
+
+			sram = <&gmu_sram>;
+			power-domains = <&mmcc OXILICX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>,
+					<&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>;
+			interconnect-names = "gfx-mem", "ocmem";
+
+			// iommus = <&gpu_iommu 0>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-27000000 {
+					opp-hz = /bits/ 64 <27000000>;
+				};
+			};
+		};
+
+		sram@fdd00000 {
+			compatible = "qcom,msm8974-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x180000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x180000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+				 <&mmcc OCMEMCX_OCMEMNOC_CLK>;
+			clock-names = "core", "iface";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x100000>;
+			};
+		};
+
+		remoteproc_adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8974-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+				label = "lpass";
+			};
+		};
+
+		imem: sram@fe805000 {
+			compatible = "qcom,msm8974-imem", "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		q6-dsp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				q6_dsp_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		modemtx-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				modemtx_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		video-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				video_alert0: trip-point0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		wlan-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				wlan_alert0: trip-point0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-top-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu1_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		gpu-bottom-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				gpu2_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2 0xf08>,
+			     <GIC_PPI 3 0xf08>,
+			     <GIC_PPI 4 0xf08>,
+			     <GIC_PPI 1 0xf08>;
+		clock-frequency = <19200000>;
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
new file mode 100644
index 000000000000..f531d2679f6c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-fairphone-fp2.dts
@@ -0,0 +1,463 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Fairphone 2";
+	compatible = "fairphone,fp2", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1;
+		mmc1 = &sdhc_2;
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_CAMERA>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&pm8941_l18>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@41 {
+		compatible = "ilitek,ili2120";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&imem {
+	reboot-mode {
+		mode-normal = <0x77665501>;
+		mode-bootloader = <0x77665500>;
+		mode-recovery = <0x77665502>;
+	};
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio1", "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pronto {
+	status = "okay";
+
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	usb-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-voltage = <4380000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
+			pins =  "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt-pins {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		fm-pins {
+			pins = "gpio41", "gpio42";
+			function = "fm";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
new file mode 100644
index 000000000000..8230d0e1d95d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts
@@ -0,0 +1,512 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "OnePlus One";
+	compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+	qcom,msm-id = <194 0x10000>;
+	qcom,board-id = <8 0>;
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
+		pinctrl-names = "default";
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			debounce-interval = <150>;
+		};
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+		power-supplies = <&bq24196_charger>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	rmi4-i2c-dev@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		syna,startup-delay-ms = <100>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+			/*
+			 * Touchscreen size is 2040x1080, y-values between
+			 * 1920-2040 are used for touchkey (menu, home & back).
+			 * For now clip it off so we don't get touch events
+			 * outside of the display area.
+			 */
+			syna,clip-y-high = <1920>;
+		};
+	};
+
+	led-controller@36 {
+		compatible = "ti,lm3630a";
+		reg = <0x36>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <80>;
+		};
+	};
+
+	led-controller@68 {
+		compatible = "si-en,sn3193";
+		reg = <0x68>;
+
+		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			label = "red:status";
+			led-max-microamp = <17500>;
+		};
+
+		led@2 {
+			reg = <2>;
+			label = "green:status";
+			led-max-microamp = <17500>;
+		};
+
+		led@3 {
+			reg = <3>;
+			label = "blue:status";
+			led-max-microamp = <17500>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	bq24196_charger: charger@6b {
+		compatible = "ti,bq24196";
+		reg = <0x6b>;
+		interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+		omit-battery-class;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&gcc {
+	compatible = "qcom,gcc-msm8974pro-ac";
+};
+
+&pm8941_coincell {
+	qcom,rset-ohms = <800>;
+	qcom,vset-millivolts = <3200>;
+
+	status = "okay";
+};
+
+&pm8941_gpios {
+	gpio_keys_default: gpio-keys-active-state {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+		input-enable;
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_vib {
+	status = "okay";
+};
+
+&pronto {
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <875000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
+		pins = "gpio68";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	touch_default_state: touch-default-state {
+		int-pins {
+			pins = "gpio61";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		reset-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active-state {
+		wlan-pins {
+			pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt-pins {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&usb {
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
new file mode 100644
index 000000000000..3e2c86591ee2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-samsung-klte.dts
@@ -0,0 +1,810 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pma8084.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Samsung Galaxy S5";
+	compatible = "samsung,klte", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_3; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-home {
+			label = "home_key";
+			gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_HOMEPAGE>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-gpio-touchkey {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_touchkey_pins>;
+
+		touchkey@20 {
+			compatible = "cypress,tm2-touchkey";
+			reg = <0x20>;
+
+			interrupt-parent = <&pma8084_gpios>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_pin>;
+
+			vcc-supply = <&max77826_ldo15>;
+			vdd-supply = <&pma8084_l19>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+		};
+	};
+
+	i2c-gpio-led {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_led_gpioex_pins>;
+
+		i2c-gpio,delay-us = <2>;
+
+		gpio_expander: gpio@20 {
+			compatible = "nxp,pcal6416";
+			reg = <0x20>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			vcc-supply = <&pma8084_s4>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpioex_pin>;
+
+			reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+		};
+
+		led-controller@30 {
+			compatible = "panasonic,an30259a";
+			reg = <0x30>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@2 {
+				reg = <2>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				reg = <3>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vreg_panel: panel-regulator {
+		compatible = "regulator-fixed";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_en_pin>;
+
+		regulator-name = "panel-vddr-reg";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+
+		gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	/delete-node/ vreg-boost;
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&max77826_ldo13>;
+		vio-supply = <&pma8084_lvs2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		syna,startup-delay-ms = <100>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	pmic@60 {
+		reg = <0x60>;
+		compatible = "maxim,max77826";
+
+		regulators {
+			max77826_ldo1: LDO1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo2: LDO2 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			max77826_ldo3: LDO3 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo4: LDO4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo5: LDO5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo6: LDO6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo7: LDO7 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo8: LDO8 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo9: LDO9 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo10: LDO10 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo11: LDO11 {
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo12: LDO12 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo13: LDO13 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo14: LDO14 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo15: LDO15 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_buck: BUCK {
+				regulator-min-microvolt = <1225000>;
+				regulator-max-microvolt = <1225000>;
+			};
+
+			max77826_buckboost: BUCKBOOST {
+				regulator-min-microvolt = <3400000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+
+	fuelgauge@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x56>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+	};
+};
+
+&blsp2_uart2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart2_pins_active>;
+	pinctrl-1 = <&blsp2_uart2_pins_sleep>;
+
+	bluetooth {
+		compatible = "brcm,bcm43540-bt";
+		max-speed = <3000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins>;
+		device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wakeup";
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pma8084_l2>;
+	vdd-supply = <&pma8084_l22>;
+	vddio-supply = <&pma8084_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "samsung,s6e3fa2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+		iovdd-supply = <&pma8084_lvs4>;
+		vddr-supply = <&vreg_panel>;
+
+		reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+		te-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pma8084_l12>;
+};
+
+&pma8084_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touchkey_pin: touchkey-int-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touch_pin: touchscreen-int-state {
+		pins = "gpio8";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	panel_en_pin: panel-en-state {
+		pins = "gpio14";
+		function = "normal";
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	wlan_sleep_clk_pin: wlan-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+	};
+
+	panel_rst_pin: panel-rst-state {
+		pins = "gpio17";
+		function = "normal";
+		bias-disable;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio21";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+	mss-supply = <&pma8084_s6>;
+	mx-supply = <&pma8084_s1>;
+	pll-supply = <&pma8084_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pma8084-regulators";
+
+		pma8084_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pma8084_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_s5: s5 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+
+		pma8084_s6: s6 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l3: l3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pma8084_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pma8084_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pma8084_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pma8084_l25: l25 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pma8084_l26: l26 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l27: l27 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_lvs1: lvs1 {};
+		pma8084_lvs2: lvs2 {};
+		pma8084_lvs3: lvs3 {};
+		pma8084_lvs4: lvs4 {};
+
+		pma8084_5vs1: 5vs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pma8084_l20>;
+	vqmmc-supply = <&pma8084_s4>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pma8084_s4>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+	};
+};
+
+&sdhc_3 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&pma8084_l21>;
+	vqmmc-supply = <&pma8084_l13>;
+
+	/*
+	 * cd-gpio is intentionally disabled. If enabled, an SD card
+	 * present during boot is not initialized correctly. Without
+	 * cd-gpios the driver resorts to polling, so hotplug works.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
+	/* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
+};
+
+&tlmm {
+	/* This seems suspicious, but somebody with this device should look into it. */
+	blsp2_uart2_pins_active: blsp2-uart2-pins-active-state {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "blsp_uart8";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep-state {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	bt_pins: bt-pins-state {
+		hostwake-pins {
+			pins = "gpio75";
+			function = "gpio";
+			drive-strength = <16>;
+		};
+
+		devwake-pins {
+			pins = "gpio91";
+			function = "gpio";
+			drive-strength = <2>;
+		};
+	};
+
+	sdc1_on: sdhc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	sdc3_on: sdc3-on-state {
+		pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+		function = "sdc3";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sdhc3_cd_pin: sdc3-cd-on-state {
+		pins = "gpio62";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_on: sdhc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	i2c_touchkey_pins: i2c-touchkey-state {
+		pins = "gpio95", "gpio96";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	i2c_led_gpioex_pins: i2c-led-gpioex-state {
+		pins = "gpio120", "gpio121";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	gpioex_pin: gpioex-state {
+		pins = "gpio145";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	wifi_pin: wifi-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	panel_te_pin: panel-state {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pma8084_l6>;
+	v3p3-supply = <&pma8084_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
new file mode 100644
index 000000000000..154639d56f35
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -0,0 +1,674 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Sony Xperia Z2 Tablet";
+	compatible = "sony,xperia-castor", "qcom,msm8974pro", "qcom,msm8974";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	vreg_bl_vddio: lcd-backlight-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bl_vddio";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		gpio = <&tlmm 69 0>;
+		enable-active-high;
+
+		vin-supply = <&pm8941_s3>;
+		startup-delay-us = <70000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_backlight_en_pin_a>;
+	};
+
+	vreg_vsp: lcd-dcdc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_vsp";
+		regulator-min-microvolt = <5600000>;
+		regulator-max-microvolt = <5600000>;
+
+		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <100>;
+
+		rmi-f01@1 {
+			reg = <0x1>;
+			syna,nosleep = <1>;
+		};
+
+		rmi-f11@11 {
+			reg = <0x11>;
+			syna,f11-flip-x = <1>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	lp8566_wled: backlight@2c {
+		compatible = "ti,lp8556";
+		reg = <0x2c>;
+		power-supply = <&vreg_bl_vddio>;
+
+		bl-name = "backlight";
+		dev-ctrl = /bits/ 8 <0x05>;
+		init-brt = /bits/ 8 <0x3f>;
+
+		rom-a0h {
+			rom-addr = /bits/ 8 <0xa0>;
+			rom-val = /bits/ 8 <0xff>;
+		};
+		rom-a1h {
+			rom-addr = /bits/ 8 <0xa1>;
+			rom-val = /bits/ 8 <0x3f>;
+		};
+		rom-a2h {
+			rom-addr = /bits/ 8 <0xa2>;
+			rom-val = /bits/ 8 <0x20>;
+		};
+		rom-a3h {
+			rom-addr = /bits/ 8 <0xa3>;
+			rom-val = /bits/ 8 <0x5e>;
+		};
+		rom-a4h {
+			rom-addr = /bits/ 8 <0xa4>;
+			rom-val = /bits/ 8 <0x02>;
+		};
+		rom-a5h {
+			rom-addr = /bits/ 8 <0xa5>;
+			rom-val = /bits/ 8 <0x04>;
+		};
+		rom-a6h {
+			rom-addr = /bits/ 8 <0xa6>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom-a7h {
+			rom-addr = /bits/ 8 <0xa7>;
+			rom-val = /bits/ 8 <0xf7>;
+		};
+		rom-a9h {
+			rom-addr = /bits/ 8 <0xa9>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom-aah {
+			rom-addr = /bits/ 8 <0xaa>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+		rom-aeh {
+			rom-addr = /bits/ 8 <0xae>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_pin>, <&bt_dev_wake_pin>, <&bt_reg_on_pin>;
+
+		host-wakeup-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8941_coincell {
+	status = "okay";
+
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	bt_reg_on_pin: bt-reg-on-state {
+		pins = "gpio16";
+		function = "normal";
+
+		output-low;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio17";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio18";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	lcd_dcdc_en_pin_a: lcd-dcdc-en-active-state {
+		pins = "gpio20";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+		input-disable;
+		output-low;
+	};
+
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <500000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	non-removable;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	usb-charge-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+};
+
+&tlmm {
+	lcd_backlight_en_pin_a: lcd-backlight-vddio-state {
+		pins = "gpio69";
+		function = "gpio";
+		drive-strength = <10>;
+		output-low;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	sdc3_on: sdc3-on-state {
+		clk-pins {
+			pins = "gpio40";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "gpio39";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "gpio35", "gpio36", "gpio37", "gpio38";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	ts_int_pin: ts-int-pin-state {
+		pins = "gpio86";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bt_host_wake_pin: bt-host-wake-state {
+		pins = "gpio95";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	bt_dev_wake_pin: bt-dev-wake-state {
+		pins = "gpio96";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi
new file mode 100644
index 000000000000..58df6e75ab6d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974pro.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+
+&gcc {
+	compatible = "qcom,gcc-msm8974pro";
+};
+
+&gpu {
+	compatible = "qcom,adreno-330.2", "qcom,adreno";
+};
+
+&sdhc_1 {
+	clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+		 <&gcc GCC_SDCC1_APPS_CLK>,
+		 <&xo_board>,
+		 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
+		 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
+	clock-names = "iface", "core", "xo", "cal", "sleep";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom/qcom-pm8226.dtsi
new file mode 100644
index 000000000000..3b8ad28cecb0
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pm8226.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: BSD-3-Clause
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8226-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8226_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm8226_0: pm8226@0 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8226_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8226-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			chg_otg: otg-vbus { };
+		};
+
+		pm8226_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8226_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			adc-chan@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			adc-chan@8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			adc-chan@9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			adc-chan@a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			adc-chan@e {
+				reg = <VADC_GND_REF>;
+			};
+			adc-chan@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8226_iadc: adc@3600 {
+			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
+			reg = <0x3600>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8226_mpps: mpps@a000 {
+			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8226_gpios: gpio@c000 {
+			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_gpios 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8226_1: pm8226@1 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8226_spmi_regulators: regulators {
+			compatible = "qcom,pm8226-regulators";
+		};
+
+		pm8226_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom/qcom-pm8841.dtsi
new file mode 100644
index 000000000000..3bf2ce5c86a6
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pm8841.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+
+/ {
+	thermal-zones {
+		pm8841-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8841_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <140000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+
+	pm8841_0: pm8841@4 {
+		compatible = "qcom,pm8841", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8841_mpps: mpps@a000 {
+			compatible = "qcom,pm8841-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8841_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8841_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
+		};
+	};
+
+	pm8841_1: pm8841@5 {
+		compatible = "qcom,pm8841", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom/qcom-pm8941.dtsi
new file mode 100644
index 000000000000..b3e246bacd78
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pm8941.dtsi
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+
+/ {
+	thermal-zones {
+		pm8941-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8941_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+
+	pm8941_0: pm8941@0 {
+		compatible = "qcom,pm8941", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>,
+			      <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pwrkey@800 {
+			compatible = "qcom,pm8941-pwrkey";
+			reg = <0x800>;
+			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+		};
+
+		usb_id: usb-detect@900 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x900>;
+			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_id";
+		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8941-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			usb-otg-in-supply = <&pm8941_5vs1>;
+
+			chg_otg: otg-vbus { };
+		};
+
+		pm8941_gpios: gpio@c000 {
+			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8941_gpios 0 0 36>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			boost_bypass_n_pin: boost-bypass-state {
+				pins = "gpio21";
+				function = "normal";
+			};
+		};
+
+		pm8941_mpps: mpps@a000 {
+			compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8941_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8941_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8941_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+
+			adc-chan@6 {
+				reg = <VADC_VBAT_SNS>;
+			};
+
+			adc-chan@8 {
+				reg = <VADC_DIE_TEMP>;
+			};
+
+			adc-chan@9 {
+				reg = <VADC_REF_625MV>;
+			};
+
+			adc-chan@a {
+				reg = <VADC_REF_1250MV>;
+			};
+
+			adc-chan@e {
+				reg = <VADC_GND_REF>;
+			};
+
+			adc-chan@f {
+				reg = <VADC_VDD_VADC>;
+			};
+
+			adc-chan@30 {
+				reg = <VADC_LR_MUX1_BAT_THERM>;
+			};
+		};
+
+		pm8941_iadc: adc@3600 {
+			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
+			reg = <0x3600>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+			qcom,external-resistor-micro-ohms = <10000>;
+		};
+
+		pm8941_coincell: charger@2800 {
+			compatible = "qcom,pm8941-coincell";
+			reg = <0x2800>;
+			status = "disabled";
+		};
+	};
+
+	pm8941_1: pm8941@1 {
+		compatible = "qcom,pm8941", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8941_lpg: pwm {
+			compatible = "qcom,pm8941-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
+		pm8941_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+
+		pm8941_wled: wled@d800 {
+			compatible = "qcom,pm8941-wled";
+			reg = <0xd800>;
+			label = "backlight";
+
+			status = "disabled";
+		};
+
+		regulators {
+			compatible = "qcom,pm8941-regulators";
+			interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
+			interrupt-names = "ocp-5vs1", "ocp-5vs2";
+			vin_5vs-supply = <&pm8941_5v>;
+
+			pm8941_5v: s4 {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-enable-ramp-delay = <500>;
+			};
+
+			pm8941_5vs1: 5vs1 {
+				regulator-enable-ramp-delay = <1000>;
+				regulator-pull-down;
+				regulator-over-current-protection;
+				qcom,ocp-max-retries = <10>;
+				qcom,ocp-retry-delay = <30>;
+				qcom,vs-soft-start-strength = <0>;
+				regulator-initial-mode = <1>;
+			};
+
+			pm8941_5vs2: 5vs2 {
+				regulator-enable-ramp-delay = <1000>;
+				regulator-pull-down;
+				regulator-over-current-protection;
+				qcom,ocp-max-retries = <10>;
+				qcom,ocp-retry-delay = <30>;
+				qcom,vs-soft-start-strength = <0>;
+				regulator-initial-mode = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom/qcom-pma8084.dtsi
new file mode 100644
index 000000000000..2dd4c6aa71c9
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pma8084.dtsi
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+
+	pma8084_0: pma8084@0 {
+		compatible = "qcom,pma8084", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>,
+			      <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pwrkey@800 {
+			compatible = "qcom,pm8941-pwrkey";
+			reg = <0x800>;
+			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+			debounce = <15625>;
+			bias-pull-up;
+		};
+
+		pma8084_gpios: gpio@c000 {
+			compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pma8084_gpios 0 0 22>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pma8084_mpps: mpps@a000 {
+			compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pma8084_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pma8084_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
+			io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+		};
+
+		pma8084_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			adc-chan@8 {
+				reg = <VADC_DIE_TEMP>;
+			};
+
+			adc-chan@9 {
+				reg = <VADC_REF_625MV>;
+			};
+
+			adc-chan@a {
+				reg = <VADC_REF_1250MV>;
+			};
+
+			adc-chan@c {
+				reg = <VADC_SPARE1>;
+			};
+
+			adc-chan@e {
+				reg = <VADC_GND_REF>;
+			};
+
+			adc-chan@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+	};
+
+	pma8084_1: pma8084@1 {
+		compatible = "qcom,pma8084", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pmx55.dtsi b/arch/arm/boot/dts/qcom/qcom-pmx55.dtsi
new file mode 100644
index 000000000000..e1b869480bbd
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pmx55.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Limited
+ */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@8 {
+		compatible = "qcom,pmx55", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		pmx55_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x8 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmx55_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx55_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x8 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+
+			chg-temp@9 {
+				reg = <ADC5_CHG_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "chg_temp";
+			};
+		};
+
+		pmx55_gpios: gpio@c000 {
+			compatible = "qcom,pmx55-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pmx55_gpios 0 0 11>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@9 {
+		compatible = "qcom,pmx55", "qcom,spmi-pmic";
+		reg = <0x9 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-pmx65.dtsi b/arch/arm/boot/dts/qcom/qcom-pmx65.dtsi
new file mode 100644
index 000000000000..1c7fdf59c1f5
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-pmx65.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@1 {
+		compatible = "qcom,pmx65", "qcom,spmi-pmic";
+		reg = <1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmx65_temp: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx65_gpios: gpio@8800 {
+			compatible = "qcom,pmx65-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmx65_gpios 0 0 16>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
new file mode 100644
index 000000000000..7e97ad5803d8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-mtp.dts
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "qcom-sdx55.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <arm64/qcom/pm8150b.dtsi>
+#include "qcom-pmx55.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDX55 MTP";
+	compatible = "qcom,sdx55-mtp", "qcom,sdx55";
+	qcom,board-id = <0x5010008 0x0>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90c00000 {
+			no-map;
+			reg = <0x90c00000 0xd400000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+};
+
+&usb_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
new file mode 100644
index 000000000000..51058b065279
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-t55.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcom-sdx55.dtsi"
+#include "qcom-pmx55.dtsi"
+
+/ {
+	model = "Thundercomm T55 Development Kit";
+	compatible = "qcom,sdx55-t55", "qcom,sdx55";
+	qcom,board-id = <0xb010008 0x4>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0xf800000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_sd_vdd: sd-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_sd_vdd";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		vin-supply = <&vreg_vddpx_2>;
+	};
+
+	vreg_vddpx_2: vddpx-2 {
+		compatible = "regulator-gpio";
+		regulator-name = "vreg_vddpx_2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2850000>;
+		enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+		gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0>, <2850000 1>;
+		startup-delay-us = <200000>;
+		enable-active-high;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1e_bb_1p2>;
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+
+	status = "okay";
+};
+
+&pcie_rc {
+	perst-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-0 = <&pcie_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* efs2 partition is secured */
+		secure-regions = /bits/ 64 <0x500000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_default: pcie-default-state {
+		clkreq-pins {
+			pins = "gpio56";
+			function = "pcie_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio57";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+		       pins = "gpio53";
+		       function = "gpio";
+		       drive-strength = <2>;
+		       bias-pull-up;
+	       };
+	};
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
new file mode 100644
index 000000000000..8fadc6e70692
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55-telit-fn980-tlb.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcom-sdx55.dtsi"
+#include "qcom-pmx55.dtsi"
+
+/ {
+	model = "Telit FN980 TLB";
+	compatible = "qcom,sdx55-telit-fn980-tlb", "qcom,sdx55";
+	qcom,board-id = <0xb010008 0x0>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_debug_mem: memory@8ef00000 {
+			no-map;
+			reg = <0x8ef00000 0x800000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0xf800000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx55-bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_s7e_mx_0p752: pmx55-s7e {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s7e_mx_0p752";
+		regulator-min-microvolt = <752000>;
+		regulator-max-microvolt = <752000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	vreg_sd_vdd: sd-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_sd_vdd";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		vin-supply = <&vreg_vddpx_2>;
+	};
+
+	vreg_vddpx_2: vddpx-2 {
+		compatible = "regulator-gpio";
+		regulator-name = "vreg_vddpx_2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2850000>;
+		enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+		gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0>, <2850000 1>;
+		startup-delay-us = <200000>;
+		enable-active-high;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx55-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-l1-l2-supply = <&vreg_s2e_1p224>;
+		vdd-l3-l9-supply = <&vreg_s3e_0p824>;
+		vdd-l4-l12-supply = <&vreg_s4e_1p904>;
+		vdd-l5-l6-supply = <&vreg_s4e_1p904>;
+		vdd-l7-l8-supply = <&vreg_s3e_0p824>;
+		vdd-l10-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l14-supply = <&vreg_s7e_mx_0p752>;
+		vdd-l15-supply = <&vreg_s2e_1p224>;
+		vdd-l16-supply = <&vreg_s4e_1p904>;
+
+		vreg_s2e_1p224: smps2 {
+			regulator-min-microvolt = <1280000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3e_0p824: smps3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s4e_1p904: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1960000>;
+		};
+
+		vreg_l1e_bb_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l4e_bb_0p875: ldo4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <872000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l5e_bb_1p7: ldo5 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		vreg_l10e_3p1: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1e_bb_1p2>;
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+
+	status = "okay";
+};
+
+&pcie_ep {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_ep_clkreq_default &pcie_ep_perst_default
+		     &pcie_ep_wake_default>;
+
+	reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <8>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* ico and efs2 partitions are secured */
+		secure-regions = /bits/ 64 <0x500000 0x500000
+					    0xa00000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+	vdda33-supply = <&vreg_l10e_3p1>;
+	vdda18-supply = <&vreg_l5e_bb_1p7>;
+
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4e_bb_0p875>;
+	vdda-pll-supply = <&vreg_l1e_bb_1p2>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi
new file mode 100644
index 000000000000..df3cd9c4ffb9
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx55.dtsi
@@ -0,0 +1,881 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SDX55 SoC device tree source
+ *
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020, Linaro Ltd.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdx55.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,sdx55.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	qcom,msm-id = <357 0x10000>, <368 0x10000>, <418 0x10000>;
+	interrupt-parent = <&intc>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <38400000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+
+		nand_clk_dummy: nand-clk-dummy {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			power-domains = <&rpmhpd SDX55_CX>;
+			power-domain-names = "rpmhpd";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdx55", "qcom,scm";
+		};
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-345600000 {
+			opp-hz = /bits/ 64 <345600000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+			required-opps = <&rpmhpd_opp_turbo>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		hyp_mem: memory@8fc00000 {
+			no-map;
+			reg = <0x8fc00000 0x80000>;
+		};
+
+		ac_db_mem: memory@8fc80000 {
+			no-map;
+			reg = <0x8fc80000 0x40000>;
+		};
+
+		secdata_mem: memory@8fcfd000 {
+			no-map;
+			reg = <0x8fcfd000 0x1000>;
+		};
+
+		sbl_mem: memory@8fd00000 {
+			no-map;
+			reg = <0x8fd00000 0x100000>;
+		};
+
+		aop_image: memory@8fe00000 {
+			no-map;
+			reg = <0x8fe00000 0x20000>;
+		};
+
+		aop_cmd_db: memory@8fe20000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x8fe20000 0x20000>;
+			no-map;
+		};
+
+		smem_mem: memory@8fe40000 {
+			no-map;
+			reg = <0x8fe40000 0xc0000>;
+		};
+
+		tz_mem: memory@8ff00000 {
+			no-map;
+			reg = <0x8ff00000 0x100000>;
+		};
+
+		tz_apps_mem: memory@90000000 {
+			no-map;
+			reg = <0x90000000 0x500000>;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&apcs 14>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdx55";
+			reg = <0x100000 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo", "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+		};
+
+		blsp1_uart3: serial@831000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x00831000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc 30>,
+				 <&gcc 9>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		usb_hsphy: phy@ff4000 {
+			compatible = "qcom,sdx55-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0x00ff4000 0x114>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_BCR>;
+		};
+
+		usb_qmpphy: phy@ff6000 {
+			compatible = "qcom,sdx55-qmp-usb3-uni-phy";
+			reg = <0x00ff6000 0x1c0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB3PHY_PHY_BCR>,
+				 <&gcc GCC_USB3_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			usb_ssphy: phy@ff6200 {
+				reg = <0x00ff6200 0x170>,
+				      <0x00ff6400 0x200>,
+				      <0x00ff6800 0x800>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
+		mc_virt: interconnect@1100000 {
+			compatible = "qcom,sdx55-mc-virt";
+			reg = <0x01100000 0x400000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		mem_noc: interconnect@9680000 {
+			compatible = "qcom,sdx55-mem-noc";
+			reg = <0x09680000 0x40000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@162c000 {
+			compatible = "qcom,sdx55-system-noc";
+			reg = <0x0162c000 0x31200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		qpic_bam: dma-controller@1b04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x01b04000 0x1c000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		qpic_nand: nand-controller@1b30000 {
+			compatible = "qcom,sdx55-nand";
+			reg = <0x01b30000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>,
+				 <&nand_clk_dummy>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+		};
+
+		pcie_rc: pcie@1c00000 {
+			compatible = "qcom,pcie-sdx55";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xc8>,
+			      <0x40001000 0x1000>,
+			      <0x40100000 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x40300000 0x0 0x3fd00000>;
+
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi",
+					  "msi2",
+					  "msi3",
+					  "msi4",
+					  "msi5",
+					  "msi6",
+					  "msi7",
+					  "msi8";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 141 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 144 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_PIPE_CLK>,
+				 <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep";
+
+			assigned-clocks = <&gcc GCC_PCIE_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommu-map = <0x0   &apps_smmu 0x0200 0x1>,
+				    <0x100 &apps_smmu 0x0201 0x1>,
+				    <0x200 &apps_smmu 0x0202 0x1>,
+				    <0x300 &apps_smmu 0x0203 0x1>,
+				    <0x400 &apps_smmu 0x0204 0x1>;
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			phys = <&pcie_lane>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
+
+		pcie_ep: pcie-ep@1c00000 {
+			compatible = "qcom,sdx55-pcie-ep";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xc8>,
+			      <0x40001000 0x1000>,
+			      <0x40200000 0x100000>,
+			      <0x01c03000 0x3000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "addr_space",
+				    "mmio";
+
+			qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+			clocks = <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep",
+				      "ref";
+
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global",
+					  "doorbell";
+
+			interconnects = <&system_noc MASTER_PCIE &mc_virt SLAVE_EBI_CH0>;
+			interconnect-names = "pcie-mem";
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "core";
+			power-domains = <&gcc PCIE_GDSC>;
+			phys = <&pcie_lane>;
+			phy-names = "pciephy";
+			max-link-speed = <3>;
+			num-lanes = <2>;
+
+			status = "disabled";
+		};
+
+		pcie_phy: phy@1c07000 {
+			compatible = "qcom,sdx55-qmp-pcie-phy";
+			reg = <0x01c07000 0x1c4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
+				 <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "refgen";
+
+			resets = <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie_lane: lanes@1c06000 {
+				reg = <0x01c06000 0x104>, /* tx0 */
+				      <0x01c06200 0x328>, /* rx0 */
+				      <0x01c07200 0x1e8>, /* pcs */
+				      <0x01c06800 0x104>, /* tx1 */
+				      <0x01c06a00 0x328>, /* rx1 */
+				      <0x01c07600 0x800>; /* pcs_misc */
+				clocks = <&gcc GCC_PCIE_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				clock-output-names = "pcie_pipe_clk";
+			};
+		};
+
+		ipa: ipa@1e40000 {
+			compatible = "qcom,sdx55-ipa";
+
+			iommus = <&apps_smmu 0x5e0 0x0>,
+				 <&apps_smmu 0x5e2 0x0>;
+			reg = <0x1e40000 0x7000>,
+			      <0x1e50000 0x4b20>,
+			      <0x1e04000 0x2c000>;
+			reg-names = "ipa-reg",
+				    "ipa-shared",
+				    "gsi";
+
+			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ipa",
+					  "gsi",
+					  "ipa-clock-query",
+					  "ipa-setup-ready";
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+			clock-names = "core";
+
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>,
+					<&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>,
+					<&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>;
+			interconnect-names = "memory",
+					     "imem",
+					     "config";
+
+			qcom,smem-states = <&ipa_smp2p_out 0>,
+					   <&ipa_smp2p_out 1>;
+			qcom,smem-state-names = "ipa-clock-enabled-valid",
+						"ipa-clock-enabled";
+
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1fc0000 {
+			compatible = "qcom,sdx55-tcsr", "syscon";
+			reg = <0x01fc0000 0x1000>;
+		};
+
+		sdhc_1: mmc@8804000 {
+			compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x08804000 0x1000>;
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>;
+			clock-names = "iface", "core";
+			status = "disabled";
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sdx55-mpss-pas";
+			reg = <0x04080000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SDX55_CX>,
+					<&rpmhpd SDX55_MSS>;
+			power-domain-names = "cx", "mss";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>;
+				label = "mpss";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs 15>;
+			};
+		};
+
+		usb: usb@a6f8800 {
+			compatible = "qcom,sdx55-dwc3", "qcom,dwc3";
+			reg = <0x0a6f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			resets = <&gcc GCC_USB30_BCR>;
+
+			usb_dwc3: dwc3@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_hsphy>, <&usb_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		pdc: interrupt-controller@b210000 {
+			compatible = "qcom,sdx55-pdc", "qcom,pdc";
+			reg = <0x0b210000 0x30000>;
+			qcom,pdc-ranges = <0 179 52>;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		restart@c264000 {
+			compatible = "qcom,pshold";
+			reg = <0x0c264000 0x1000>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0c440000 0x0000d00>,
+			      <0x0c600000 0x2000000>,
+			      <0x0e600000 0x0100000>,
+			      <0x0e700000 0x00a0000>,
+			      <0x0c40a000 0x0000700>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			cell-index = <0>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sdx55-pinctrl";
+			reg = <0xf100000 0x300000>;
+			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 108>;
+		};
+
+		sram@1468f000 {
+			compatible = "qcom,sdx55-imem", "syscon", "simple-mfd";
+			reg = <0x1468f000 0x1000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x0 0x1468f000 0x1000>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0x200>;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdx55-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x15000000 0x20000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17800000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <3>;
+			reg = <0x17800000 0x1000>,
+			      <0x17802000 0x1000>;
+		};
+
+		a7pll: clock@17808000 {
+			compatible = "qcom,sdx55-a7pll";
+			reg = <0x17808000 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <0>;
+		};
+
+		apcs: mailbox@17810000 {
+			compatible = "qcom,sdx55-apcs-gcc", "syscon";
+			reg = <0x17810000 0x2000>;
+			#mbox-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>;
+			clock-names = "ref", "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		watchdog@17817000 {
+			compatible = "qcom,apss-wdt-sdx55", "qcom,kpss-wdt";
+			reg = <0x17817000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@17820000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x17820000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17821000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 7 0x4>,
+					     <GIC_SPI 6 0x4>;
+				reg = <0x17821000 0x1000>,
+				      <0x17822000 0x1000>;
+			};
+
+			frame@17823000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 8 0x4>;
+				reg = <0x17823000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17824000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 9 0x4>;
+				reg = <0x17824000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17825000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 10 0x4>;
+				reg = <0x17825000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17826000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 11 0x4>;
+				reg = <0x17826000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17827000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 12 0x4>;
+				reg = <0x17827000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17828000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 13 0x4>;
+				reg = <0x17828000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17829000 {
+				frame-number = <7>;
+				interrupts = <GIC_SPI 14 0x4>;
+				reg = <0x17829000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17830000 {
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x17830000 0x10000>, <0x17840000 0x10000>;
+			reg-names = "drv-0", "drv-1";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <1>;
+			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   2>,
+					  <WAKE_TCS    2>, <CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdx55-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdx55-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
new file mode 100644
index 000000000000..02d8d6e241ae
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65-mtp.dts
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include "qcom-sdx65.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <arm64/qcom/pmk8350.dtsi>
+#include <arm64/qcom/pm8150b.dtsi>
+#include "qcom-pmx65.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDX65 MTP";
+	compatible = "qcom,sdx65-mtp", "qcom,sdx65";
+	qcom,board-id = <0x2010008 0x302>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_dsm: memory@8c400000 {
+			no-map;
+			reg = <0x8c400000 0x3200000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0x10000000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx65_bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmx65-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-l1-supply = <&vreg_s2b_1p224>;
+		vdd-l2-l18-supply = <&vreg_s2b_1p224>;
+		vdd-l3-supply = <&vreg_s8b_0p824>;
+		vdd-l4-supply = <&vreg_s7b_0p936>;
+		vdd-l5-l6-l16-supply = <&vreg_s4b_1p824>;
+		vdd-l7-supply = <&vreg_s3b_0p776>;
+		vdd-l8-l9-supply = <&vreg_s8b_0p824>;
+		vdd-l10-supply = <&vreg_bob_3p3>;
+		vdd-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l12-supply = <&vreg_s2b_1p224>;
+		vdd-l14-supply = <&vreg_s3b_0p776>;
+		vdd-l15-supply = <&vreg_s2b_1p224>;
+		vdd-l17-supply = <&vreg_s8b_0p824>;
+		vdd-l19-supply = <&vreg_s3b_0p776>;
+		vdd-l20-supply = <&vreg_s7b_0p936>;
+		vdd-l21-supply = <&vreg_s7b_0p936>;
+
+		vreg_s2b_1p224: smps2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3b_0p776: smps3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s4b_1p824: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s7b_0p936: smps7 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s8b_0p824: smps8 {
+			regulator-min-microvolt = <304000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		vreg_l1b_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_0p88: ldo4 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_1p8: ldo5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_3p08: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo17 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo19 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo20 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo21 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&ipa {
+	qcom,gsi-loader = "skip";
+	status = "okay";
+};
+
+&pcie_ep {
+	pinctrl-0 = <&pcie_ep_clkreq_default
+		     &pcie_ep_perst_default
+		     &pcie_ep_wake_default>;
+	pinctrl-names = "default";
+
+	reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l1b_1p2>;
+	vdda-pll-supply = <&vreg_l4b_0p88>;
+
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* ico and efs2 partitions are secured */
+		secure-regions = /bits/ 64 <0x500000 0x500000
+					    0xa00000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	memory-region = <&mpss_adsp_mem>;
+	status = "okay";
+};
+
+&tlmm {
+	pcie_ep_clkreq_default: pcie-ep-clkreq-default-state {
+		pins = "gpio56";
+		function = "pcie_clkreq";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie_ep_perst_default: pcie-ep-perst-default-state {
+		pins = "gpio57";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	pcie_ep_wake_default: pcie-ep-wake-default-state {
+		pins = "gpio53";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_hsphy {
+	vdda-pll-supply = <&vreg_l4b_0p88>;
+	vdda33-supply = <&vreg_l10b_3p08>;
+	vdda18-supply = <&vreg_l5b_1p8>;
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l4b_0p88>;
+	vdda-pll-supply = <&vreg_l1b_1p2>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
new file mode 100644
index 000000000000..1a3583029a64
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
@@ -0,0 +1,811 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SDX65 SoC device tree source
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ *
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdx65.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/interconnect/qcom,sdx65.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	qcom,msm-id = <458 0x10000>, <483 0x10000>, <509 0x10000>;
+	interrupt-parent = <&intc>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			clock-output-names = "sleep_clk";
+			#clock-cells = <0>;
+		};
+
+		nand_clk_dummy: nand-clk-dummy {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			power-domains = <&rpmhpd SDX65_CX_AO>;
+			power-domain-names = "rpmhpd";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdx65", "qcom,scm";
+		};
+	};
+
+	mc_virt: interconnect-mc-virt {
+		compatible = "qcom,sdx65-mc-virt";
+		#interconnect-cells = <1>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-345600000 {
+			opp-hz = /bits/ 64 <345600000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			required-opps = <&rpmhpd_opp_turbo>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		tz_heap_mem: memory@8fcad000 {
+			no-map;
+			reg = <0x8fcad000 0x40000>;
+		};
+
+		secdata_mem: memory@8fcfd000 {
+			no-map;
+			reg = <0x8fcfd000 0x1000>;
+		};
+
+		hyp_mem: memory@8fd00000 {
+			no-map;
+			reg = <0x8fd00000 0x80000>;
+		};
+
+		access_control_mem: memory@8fd80000 {
+			no-map;
+			reg = <0x8fd80000 0x80000>;
+		};
+
+		aop_mem: memory@8fe00000 {
+			no-map;
+			reg = <0x8fe00000 0x20000>;
+		};
+
+		smem_mem: memory@8fe20000 {
+			compatible = "qcom,smem";
+			reg = <0x8fe20000 0xc0000>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		cmd_db: reserved-memory@8fee0000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x8fee0000 0x20000>;
+			no-map;
+		};
+
+		tz_mem: memory@8ff00000 {
+			no-map;
+			reg = <0x8ff00000 0x100000>;
+		};
+
+		tz_apps_mem: memory@90000000 {
+			no-map;
+			reg = <0x90000000 0x500000>;
+		};
+
+		llcc_tcm_mem: memory@15800000 {
+			no-map;
+			reg = <0x15800000 0x800000>;
+		};
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&apcs 14>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdx65";
+			reg = <0x00100000 0x001f7400>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>;
+			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+			#power-domain-cells = <1>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		blsp1_uart3: serial@831000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x00831000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		usb_hsphy: phy@ff4000 {
+			compatible = "qcom,sdx65-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0xff4000 0x120>;
+			#phy-cells = <0>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_BCR>;
+			status = "disabled";
+		};
+
+		usb_qmpphy: phy@ff6000 {
+			compatible = "qcom,sdx65-qmp-usb3-uni-phy";
+			reg = <0x00ff6000 0x1c8>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_EN>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB3PHY_PHY_BCR>,
+				 <&gcc GCC_USB3_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			status = "disabled";
+
+			usb_ssphy: phy@ff6200 {
+				reg = <0x00ff6e00 0x160>,
+				      <0x00ff7000 0x1ec>,
+				      <0x00ff6200 0x1e00>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
+		system_noc: interconnect@1620000 {
+			compatible = "qcom,sdx65-system-noc";
+			reg = <0x01620000 0x31200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		qpic_bam: dma-controller@1b04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x01b04000 0x1c000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		qpic_nand: nand-controller@1b30000 {
+			compatible = "qcom,sdx55-nand";
+			reg = <0x01b30000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>,
+				 <&nand_clk_dummy>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+		};
+
+		pcie_ep: pcie-ep@1c00000 {
+			compatible = "qcom,sdx65-pcie-ep", "qcom,sdx55-pcie-ep";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xa8>,
+			      <0x40001000 0x1000>,
+			      <0x40200000 0x100000>,
+			      <0x01c03000 0x3000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "addr_space",
+				    "mmio";
+
+			qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+			clocks = <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "sleep",
+				      "ref";
+
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global", "doorbell";
+
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "core";
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			phys = <&pcie_phy>;
+			phy-names = "pcie-phy";
+
+			max-link-speed = <3>;
+			num-lanes = <2>;
+
+			status = "disabled";
+		};
+
+		pcie_phy: phy@1c06000 {
+			compatible = "qcom,sdx65-qmp-gen4x2-pcie-phy";
+			reg = <0x01c06000 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_RCHNG_PHY_CLK>,
+				 <&gcc GCC_PCIE_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1fcb000 {
+			compatible = "qcom,sdx65-tcsr", "syscon";
+			reg = <0x01fc0000 0x1000>;
+		};
+
+		ipa: ipa@3f40000 {
+			compatible = "qcom,sdx65-ipa";
+
+			reg = <0x03f40000 0x10000>,
+			      <0x03f50000 0x5000>,
+			      <0x03e04000 0xfc000>;
+			reg-names = "ipa-reg",
+				    "ipa-shared",
+				    "gsi";
+
+			interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ipa",
+					  "gsi",
+					  "ipa-clock-query",
+					  "ipa-setup-ready";
+
+			iommus = <&apps_smmu 0x5e0 0x0>,
+				 <&apps_smmu 0x5e2 0x0>;
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+			clock-names = "core";
+
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI1>,
+					<&mem_noc MASTER_APPSS_PROC &system_noc SLAVE_IPA_CFG>;
+			interconnect-names = "memory",
+					     "config";
+
+			qcom,smem-states = <&ipa_smp2p_out 0>,
+					   <&ipa_smp2p_out 1>;
+			qcom,smem-state-names = "ipa-clock-enabled-valid",
+						"ipa-clock-enabled";
+
+			status = "disabled";
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sdx55-mpss-pas";
+			reg = <0x04080000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SDX65_CX>,
+					<&rpmhpd SDX65_MSS>;
+			power-domain-names = "cx", "mss";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>;
+				label = "mpss";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs 15>;
+			};
+		};
+
+		sdhc_1: mmc@8804000 {
+			compatible = "qcom,sdx65-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x08804000 0x1000>;
+			reg-names = "hc";
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&gcc GCC_SDCC1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		mem_noc: interconnect@9680000 {
+			compatible = "qcom,sdx65-mem-noc";
+			reg = <0x09680000 0x27200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		usb: usb@a6f8800 {
+			compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
+			reg = <0x0a6f8800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+					"sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 76 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 18 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 19 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			resets = <&gcc GCC_USB30_BCR>;
+
+			status = "disabled";
+
+			usb_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_hsphy>, <&usb_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		restart@c264000 {
+			compatible = "qcom,pshold";
+			reg = <0x0c264000 0x1000>;
+		};
+
+		spmi_bus: qcom,spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0xc440000 0xd00>,
+				<0xc600000 0x2000000>,
+				<0xe600000 0x100000>,
+				<0xe700000 0xa0000>,
+				<0xc40a000 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			qcom,channel = <0>;
+			qcom,ee = <0>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sdx65-tlmm";
+			reg = <0xf100000 0x300000>;
+			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 109>;
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <2>;
+		};
+
+		pdc: interrupt-controller@b210000 {
+			compatible = "qcom,sdx65-pdc", "qcom,pdc";
+			reg = <0xb210000 0x10000>;
+			qcom,pdc-ranges = <0 147 52>, <52 266 32>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		sram@1468f000 {
+			compatible = "qcom,sdx65-imem", "syscon", "simple-mfd";
+			reg = <0x1468f000 0x1000>;
+			ranges = <0x0 0x1468f000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0xc8>;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdx65-smmu-500", "qcom,smmu-500", "arm,mmu-500";
+			reg = <0x15000000 0x40000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts =	<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17800000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <3>;
+			reg = <0x17800000 0x1000>,
+			      <0x17802000 0x1000>;
+		};
+
+		a7pll: clock@17808000 {
+			compatible = "qcom,sdx55-a7pll";
+			reg = <0x17808000 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <0>;
+		};
+
+		apcs: mailbox@17810000 {
+			compatible = "qcom,sdx55-apcs-gcc", "syscon";
+			reg = <0x17810000 0x2000>;
+			#mbox-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>;
+			clock-names = "ref", "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		watchdog@17817000 {
+			compatible = "qcom,apss-wdt-sdx65", "qcom,kpss-wdt";
+			reg = <0x17817000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@17820000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x17820000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17821000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 7 0x4>,
+					     <GIC_SPI 6 0x4>;
+				reg = <0x17821000 0x1000>,
+				      <0x17822000 0x1000>;
+			};
+
+			frame@17823000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 8 0x4>;
+				reg = <0x17823000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17824000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 9 0x4>;
+				reg = <0x17824000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17825000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 10 0x4>;
+				reg = <0x17825000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17826000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 11 0x4>;
+				reg = <0x17826000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17827000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 12 0x4>;
+				reg = <0x17827000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17828000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 13 0x4>;
+				reg = <0x17828000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17829000 {
+				frame-number = <7>;
+				interrupts = <GIC_SPI 14 0x4>;
+				reg = <0x17829000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17830000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x17830000 0x10000>,
+			    <0x17840000 0x10000>;
+			reg-names = "drv-0", "drv-1";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <1>;
+			qcom,tcs-config = <ACTIVE_TCS  2>,
+				<SLEEP_TCS   2>,
+				<WAKE_TCS    2>,
+				<CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdx65-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdx65-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 13 0xf08>,
+			<1 12 0xf08>,
+			<1 10 0xf08>,
+			<1 11 0xf08>;
+		clock-frequency = <19200000>;
+	};
+};