Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

150 files changed, 42653 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/st/Makefile b/arch/arm/boot/dts/st/Makefile
new file mode 100644
index 000000000000..b3e9d29390e3
--- /dev/null
+++ b/arch/arm/boot/dts/st/Makefile
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NOMADIK) += \
+	ste-nomadik-s8815.dtb \
+	ste-nomadik-nhk15.dtb
+dtb-$(CONFIG_ARCH_SPEAR13XX) += \
+	spear1310-evb.dtb \
+	spear1340-evb.dtb
+dtb-$(CONFIG_ARCH_SPEAR3XX) += \
+	spear300-evb.dtb \
+	spear310-evb.dtb \
+	spear320-evb.dtb \
+	spear320-hmi.dtb
+dtb-$(CONFIG_ARCH_SPEAR6XX) += \
+	spear600-evb.dtb
+dtb-$(CONFIG_ARCH_STI) += \
+	stih407-b2120.dtb \
+	stih410-b2120.dtb \
+	stih410-b2260.dtb \
+	stih418-b2199.dtb \
+	stih418-b2264.dtb
+dtb-$(CONFIG_ARCH_STM32) += \
+	stm32f429-disco.dtb \
+	stm32f469-disco.dtb \
+	stm32f746-disco.dtb \
+	stm32f769-disco.dtb \
+	stm32429i-eval.dtb \
+	stm32746g-eval.dtb \
+	stm32h743i-eval.dtb \
+	stm32h743i-disco.dtb \
+	stm32h750i-art-pi.dtb \
+	stm32mp135f-dk.dtb \
+	stm32mp151a-prtt1a.dtb \
+	stm32mp151a-prtt1c.dtb \
+	stm32mp151a-prtt1s.dtb \
+	stm32mp151a-dhcor-testbench.dtb \
+	stm32mp153c-dhcom-drc02.dtb \
+	stm32mp153c-dhcor-drc-compact.dtb \
+	stm32mp157a-avenger96.dtb \
+	stm32mp157a-dhcor-avenger96.dtb \
+	stm32mp157a-dk1.dtb \
+	stm32mp157a-dk1-scmi.dtb \
+	stm32mp157a-iot-box.dtb \
+	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
+	stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2-of10.dtb \
+	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
+	stm32mp157a-stinger96.dtb \
+	stm32mp157c-dhcom-pdk2.dtb \
+	stm32mp157c-dhcom-picoitx.dtb \
+	stm32mp157c-dk2.dtb \
+	stm32mp157c-dk2-scmi.dtb \
+	stm32mp157c-ed1.dtb \
+	stm32mp157c-ed1-scmi.dtb \
+	stm32mp157c-emsbc-argon.dtb \
+	stm32mp157c-ev1.dtb \
+	stm32mp157c-ev1-scmi.dtb \
+	stm32mp157c-lxa-mc1.dtb \
+	stm32mp157c-odyssey.dtb \
+	stm32mp157c-phycore-stm32mp1-3.dtb
+dtb-$(CONFIG_ARCH_U8500) += \
+	ste-snowball.dtb \
+	ste-hrefprev60-stuib.dtb \
+	ste-hrefprev60-tvk.dtb \
+	ste-hrefv60plus-stuib.dtb \
+	ste-hrefv60plus-tvk.dtb \
+	ste-href520-tvk.dtb \
+	ste-ux500-samsung-golden.dtb \
+	ste-ux500-samsung-janice.dtb \
+	ste-ux500-samsung-gavini.dtb \
+	ste-ux500-samsung-codina.dtb \
+	ste-ux500-samsung-codina-tmo.dtb \
+	ste-ux500-samsung-skomer.dtb \
+	ste-ux500-samsung-kyle.dtb
diff --git a/arch/arm/boot/dts/st/spear1310-evb.dts b/arch/arm/boot/dts/st/spear1310-evb.dts
new file mode 100644
index 000000000000..05408df38203
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear1310-evb.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr1310 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/dts-v1/;
+/include/ "spear1310.dtsi"
+
+/ {
+	model = "ST SPEAr1310 Evaluation Board";
+	compatible = "st,spear1310-evb", "st,spear1310";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@e0700000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				i2s0 {
+					st,pins = "i2s0_grp";
+					st,function = "i2s0";
+				};
+				i2s1 {
+					st,pins = "i2s1_grp";
+					st,function = "i2s1";
+				};
+				gpio {
+					st,pins = "arm_gpio_grp";
+					st,function = "arm_gpio";
+				};
+				clcd {
+					st,pins = "clcd_grp" , "clcd_high_res";
+					st,function = "clcd";
+				};
+				eth {
+					st,pins = "gmii_grp";
+					st,function = "gmii";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				kbd {
+					st,pins = "keyboard_6x6_grp";
+					st,function = "keyboard";
+				};
+				sdhci {
+					st,pins = "sdhci_grp";
+					st,function = "sdhci";
+				};
+				smi-pmx {
+					st,pins = "smi_2_chips_grp";
+					st,function = "smi";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				rs485 {
+					st,pins = "rs485_0_1_tdm_0_1_grp";
+					st,function = "rs485_0_1_tdm_0_1";
+				};
+				i2c1_2 {
+					st,pins = "i2c_1_2_grp";
+					st,function = "i2c_1_2";
+				};
+				smii {
+					st,pins = "smii_0_1_2_grp";
+					st,function = "smii_0_1_2";
+				};
+				nand {
+					st,pins = "nand_8bit_grp",
+						"nand_16bit_grp";
+					st,function = "nand";
+				};
+				sata {
+					st,pins = "sata0_grp";
+					st,function = "sata";
+				};
+				pcie {
+					st,pins = "pcie1_grp", "pcie2_grp";
+					st,function = "pci_express";
+				};
+			};
+		};
+
+		ahci@b1000000 {
+			status = "okay";
+		};
+
+		miphy@eb800000 {
+			status = "okay";
+		};
+
+		cf@b2800000 {
+			status = "okay";
+		};
+
+		dma@ea800000 {
+			status = "okay";
+		};
+
+		dma@eb000000 {
+			status = "okay";
+		};
+
+		fsmc: flash@b0000000 {
+			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x80000>;
+			};
+			partition@80000 {
+				label = "u-boot";
+				reg = <0x80000 0x140000>;
+			};
+			partition@1C0000 {
+				label = "environment";
+				reg = <0x1C0000 0x40000>;
+			};
+			partition@200000 {
+				label = "dtb";
+				reg = <0x200000 0x40000>;
+			};
+			partition@240000 {
+				label = "linux";
+				reg = <0x240000 0xC00000>;
+			};
+			partition@E40000 {
+				label = "rootfs";
+				reg = <0xE40000 0x0>;
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "wakeup";
+				linux,code = <0x100>;
+				gpios = <&gpio0 7 0x4>;
+				debounce-interval = <20>;
+				wakeup-source;
+			};
+		};
+
+		gmac0: eth@e2000000 {
+			phy-mode = "gmii";
+			status = "okay";
+		};
+
+		sdhci@b3000000 {
+			status = "okay";
+		};
+
+		smi: flash@ea000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@e6000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xe6000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		ehci@e4800000 {
+			status = "okay";
+		};
+
+		ehci@e5800000 {
+			status = "okay";
+		};
+
+		ohci@e4000000 {
+			status = "okay";
+		};
+
+		ohci@e5000000 {
+			status = "okay";
+		};
+
+		apb {
+			adc@e0080000 {
+				status = "okay";
+			};
+
+			gpio0: gpio@e0600000 {
+			       status = "okay";
+			};
+
+			gpio1: gpio@e0680000 {
+			       status = "okay";
+			};
+
+			gpio@d8400000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@e0280000 {
+			       status = "okay";
+			};
+
+			kbd@e0300000 {
+				linux,keymap = < 0x00000001
+						 0x00010002
+						 0x00020003
+						 0x00030004
+						 0x00040005
+						 0x00050006
+						 0x00060007
+						 0x00070008
+						 0x00080009
+						 0x0100000a
+						 0x0101000c
+						 0x0102000d
+						 0x0103000e
+						 0x0104000f
+						 0x01050010
+						 0x01060011
+						 0x01070012
+						 0x01080013
+						 0x02000014
+						 0x02010015
+						 0x02020016
+						 0x02030017
+						 0x02040018
+						 0x02050019
+						 0x0206001a
+						 0x0207001b
+						 0x0208001c
+						 0x0300001d
+						 0x0301001e
+						 0x0302001f
+						 0x03030020
+						 0x03040021
+						 0x03050022
+						 0x03060023
+						 0x03070024
+						 0x03080025
+						 0x04000026
+						 0x04010027
+						 0x04020028
+						 0x04030029
+						 0x0404002a
+						 0x0405002b
+						 0x0406002c
+						 0x0407002d
+						 0x0408002e
+						 0x0500002f
+						 0x05010030
+						 0x05020031
+						 0x05030032
+						 0x05040033
+						 0x05050034
+						 0x05060035
+						 0x05070036
+						 0x05080037
+						 0x06000038
+						 0x06010039
+						 0x0602003a
+						 0x0603003b
+						 0x0604003c
+						 0x0605003d
+						 0x0606003e
+						 0x0607003f
+						 0x06080040
+						 0x07000041
+						 0x07010042
+						 0x07020043
+						 0x07030044
+						 0x07040045
+						 0x07050046
+						 0x07060047
+						 0x07070048
+						 0x07080049
+						 0x0800004a
+						 0x0801004b
+						 0x0802004c
+						 0x0803004d
+						 0x0804004e
+						 0x0805004f
+						 0x08060050
+						 0x08070051
+						 0x08080052 >;
+			       autorepeat;
+			       st,mode = <0>;
+			       suspended_rate = <2000000>;
+			       status = "okay";
+			};
+
+			rtc@e0580000 {
+			       status = "okay";
+			};
+
+			serial@e0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			spi0: spi@e0100000 {
+				status = "okay";
+				num-cs = <3>;
+				cs-gpios = <&gpio1 7 0>, <&spics 0 0>, <&spics 1 0>;
+
+				stmpe610@0 {
+					compatible = "st,stmpe610";
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					spi-max-frequency = <1000000>;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x7>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+					interrupts = <6 0x4>;
+					interrupt-parent = <&gpio1>;
+					irq-trigger = <0x2>;
+
+					stmpe_touchscreen {
+						compatible = "st,stmpe-ts";
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <2>;
+						ts,settling = <2>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+
+				flash@1 {
+					compatible = "st,m25p80";
+					reg = <1>;
+					spi-max-frequency = <12000000>;
+					spi-cpol;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
+			};
+
+			wdt@ec800620 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear1310.dtsi b/arch/arm/boot/dts/st/spear1310.dtsi
new file mode 100644
index 000000000000..2f746a9428a7
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear1310.dtsi
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for all SPEAr1310 SoCs
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/include/ "spear13xx.dtsi"
+
+/ {
+	compatible = "st,spear1310";
+
+	ahb {
+		spics: spics@e0700000{
+			compatible = "st,spear-spics-gpio";
+			reg = <0xe0700000 0x1000>;
+			st-spics,peripcfg-reg = <0x3b0>;
+			st-spics,sw-enable-bit = <12>;
+			st-spics,cs-value-bit = <11>;
+			st-spics,cs-enable-mask = <3>;
+			st-spics,cs-enable-shift = <8>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		miphy0: miphy@eb800000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb800000 0x4000>;
+			misc = <&misc>;
+			phy-id = <0>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		miphy1: miphy@eb804000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb804000 0x4000>;
+			misc = <&misc>;
+			phy-id = <1>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		miphy2: miphy@eb808000 {
+			compatible = "st,spear1310-miphy";
+			reg = <0xeb808000 0x4000>;
+			misc = <&misc>;
+			phy-id = <2>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ahci0: ahci@b1000000 {
+			compatible = "snps,spear-ahci";
+			reg = <0xb1000000 0x10000>;
+			interrupts = <0 68 0x4>;
+			phys = <&miphy0 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		ahci1: ahci@b1800000 {
+			compatible = "snps,spear-ahci";
+			reg = <0xb1800000 0x10000>;
+			interrupts = <0 69 0x4>;
+			phys = <&miphy1 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		ahci2: ahci@b4000000 {
+			compatible = "snps,spear-ahci";
+			reg = <0xb4000000 0x10000>;
+			interrupts = <0 70 0x4>;
+			phys = <&miphy2 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		pcie0: pcie@b1000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
+			reg-names = "dbi", "config";
+			interrupts = <0 68 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy0 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0	 0x80020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			bus-range = <0x00 0xff>;
+			status = "disabled";
+		};
+
+		pcie1: pcie@b1800000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1800000 0x4000>, <0x90000000 0x20000>;
+			reg-names = "dbi", "config";
+			interrupts = <0 69 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy1 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0  0x90020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x90030000 0x90030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			bus-range = <0x00 0xff>;
+			status = "disabled";
+		};
+
+		pcie2: pcie@b4000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb4000000 0x4000>, <0xc0000000 0x20000>;
+			reg-names = "dbi", "config";
+			interrupts = <0 70 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy2 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0	 0xc0020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0xc0030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			bus-range = <0x00 0xff>;
+			status = "disabled";
+		};
+
+		gmac1: eth@5c400000 {
+			compatible = "st,spear600-gmac";
+			reg = <0x5c400000 0x8000>;
+			interrupts = <0 95 0x4>;
+			interrupt-names = "macirq";
+			phy-mode = "mii";
+			status = "disabled";
+		};
+
+		gmac2: eth@5c500000 {
+			compatible = "st,spear600-gmac";
+			reg = <0x5c500000 0x8000>;
+			interrupts = <0 96 0x4>;
+			interrupt-names = "macirq";
+			phy-mode = "mii";
+			status = "disabled";
+		};
+
+		gmac3: eth@5c600000 {
+			compatible = "st,spear600-gmac";
+			reg = <0x5c600000 0x8000>;
+			interrupts = <0 97 0x4>;
+			interrupt-names = "macirq";
+			phy-mode = "rmii";
+			status = "disabled";
+		};
+
+		gmac4: eth@5c700000 {
+			compatible = "st,spear600-gmac";
+			reg = <0x5c700000 0x8000>;
+			interrupts = <0 98 0x4>;
+			interrupt-names = "macirq";
+			phy-mode = "rgmii";
+			status = "disabled";
+		};
+
+		pinmux: pinmux@e0700000 {
+			compatible = "st,spear1310-pinmux";
+			reg = <0xe0700000 0x1000>;
+			#gpio-range-cells = <3>;
+		};
+
+		apb {
+			i2c1: i2c@5cd00000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5cd00000 0x1000>;
+				interrupts = <0 87 0x4>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@5ce00000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5ce00000 0x1000>;
+				interrupts = <0 88 0x4>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@5cf00000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5cf00000 0x1000>;
+				interrupts = <0 89 0x4>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@5d000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5d000000 0x1000>;
+				interrupts = <0 90 0x4>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@5d100000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5d100000 0x1000>;
+				interrupts = <0 91 0x4>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@5d200000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5d200000 0x1000>;
+				interrupts = <0 92 0x4>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@5d300000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0x5d300000 0x1000>;
+				interrupts = <0 93 0x4>;
+				status = "disabled";
+			};
+
+			spi1: spi@5d400000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0x5d400000 0x1000>;
+				interrupts = <0 99 0x4>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			serial@5c800000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x5c800000 0x1000>;
+				interrupts = <0 82 0x4>;
+				status = "disabled";
+			};
+
+			serial@5c900000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x5c900000 0x1000>;
+				interrupts = <0 83 0x4>;
+				status = "disabled";
+			};
+
+			serial@5ca00000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x5ca00000 0x1000>;
+				interrupts = <0 84 0x4>;
+				status = "disabled";
+			};
+
+			serial@5cb00000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x5cb00000 0x1000>;
+				interrupts = <0 85 0x4>;
+				status = "disabled";
+			};
+
+			serial@5cc00000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x5cc00000 0x1000>;
+				interrupts = <0 86 0x4>;
+				status = "disabled";
+			};
+
+			thermal@e07008c4 {
+				st,thermal-flags = <0x7000>;
+			};
+
+			gpiopinctrl: gpio@d8400000 {
+				compatible = "st,spear-plgpio";
+				reg = <0xd8400000 0x1000>;
+				interrupts = <0 100 0x4>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinmux 0 0 246>;
+				status = "disabled";
+
+				st-plgpio,ngpio = <246>;
+				st-plgpio,enb-reg = <0xd0>;
+				st-plgpio,wdata-reg = <0x90>;
+				st-plgpio,dir-reg = <0xb0>;
+				st-plgpio,ie-reg = <0x30>;
+				st-plgpio,rdata-reg = <0x70>;
+				st-plgpio,mis-reg = <0x10>;
+				st-plgpio,eit-reg = <0x50>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear1340-evb.dts b/arch/arm/boot/dts/st/spear1340-evb.dts
new file mode 100644
index 000000000000..7700f2afc128
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear1340-evb.dts
@@ -0,0 +1,503 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr1340 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/dts-v1/;
+/include/ "spear1340.dtsi"
+
+/ {
+	model = "ST SPEAr1340 Evaluation Board";
+	compatible = "st,spear1340-evb", "st,spear1340";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@e0700000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				pads_as_gpio {
+					st,pins = "pads_as_gpio_grp";
+					st,function = "pads_as_gpio";
+				};
+				fsmc {
+					st,pins = "fsmc_8bit_grp";
+					st,function = "fsmc";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				i2c1 {
+					st,pins = "i2c1_grp";
+					st,function = "i2c1";
+				};
+				spdif-in {
+					st,pins = "spdif_in_grp";
+					st,function = "spdif_in";
+				};
+				spdif-out {
+					st,pins = "spdif_out_grp";
+					st,function = "spdif_out";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp", "ssp0_cs1_grp", "ssp0_cs2_grp", "ssp0_cs3_grp";
+					st,function = "ssp0";
+				};
+				smi-pmx {
+					st,pins = "smi_grp";
+					st,function = "smi";
+				};
+				i2s {
+					st,pins = "i2s_in_grp", "i2s_out_grp";
+					st,function = "i2s";
+				};
+				gmac {
+					st,pins = "gmii_grp", "rgmii_grp";
+					st,function = "gmac";
+				};
+				cam0 {
+					st,pins = "cam0_grp";
+					st,function = "cam0";
+				};
+				cam1 {
+					st,pins = "cam1_grp";
+					st,function = "cam1";
+				};
+				cam2 {
+					st,pins = "cam2_grp";
+					st,function = "cam2";
+				};
+				cam3 {
+					st,pins = "cam3_grp";
+					st,function = "cam3";
+				};
+				cec0 {
+					st,pins = "cec0_grp";
+					st,function = "cec0";
+				};
+				cec1 {
+					st,pins = "cec1_grp";
+					st,function = "cec1";
+				};
+				sdhci {
+					st,pins = "sdhci_grp";
+					st,function = "sdhci";
+				};
+				clcd {
+					st,pins = "clcd_grp";
+					st,function = "clcd";
+				};
+				sata {
+					st,pins = "sata_grp";
+					st,function = "sata";
+				};
+				pcie {
+					st,pins = "pcie_grp";
+					st,function = "pcie";
+				};
+
+			};
+		};
+
+		ahci@b1000000 {
+			status = "okay";
+		};
+
+		miphy@eb800000 {
+			status = "okay";
+		};
+
+		dma@ea800000 {
+			status = "okay";
+		};
+
+		dma@eb000000 {
+			status = "okay";
+		};
+
+		fsmc: flash@b0000000 {
+			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x200000>;
+			};
+			partition@200000 {
+				label = "u-boot";
+				reg = <0x200000 0x200000>;
+			};
+			partition@400000 {
+				label = "environment";
+				reg = <0x400000 0x100000>;
+			};
+			partition@500000 {
+				label = "dtb";
+				reg = <0x500000 0x100000>;
+			};
+			partition@600000 {
+				label = "linux";
+				reg = <0x600000 0xC00000>;
+			};
+			partition@1200000 {
+				label = "rootfs";
+				reg = <0x1200000 0x0>;
+			};
+		};
+
+		gmac0: eth@e2000000 {
+			phy-mode = "rgmii";
+			status = "okay";
+		};
+
+		sdhci@b3000000 {
+			status = "okay";
+		};
+
+		smi: flash@ea000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@e6000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xe6000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		ehci@e4800000 {
+			status = "okay";
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "wakeup";
+				linux,code = <0x100>;
+				gpios = <&gpio1 1 0x4>;
+				debounce-interval = <20>;
+				wakeup-source;
+			};
+		};
+
+		ehci@e5800000 {
+			status = "okay";
+		};
+
+		i2s0: i2s-play@b2400000 {
+			status = "okay";
+		};
+
+		i2s1: i2s-rec@b2000000 {
+			status = "okay";
+		};
+
+		incodec: dir-hifi {
+			compatible = "dummy,dir-hifi";
+			status = "okay";
+		};
+
+		ohci@e4000000 {
+			status = "okay";
+		};
+
+		ohci@e5000000 {
+			status = "okay";
+		};
+
+		outcodec: dit-hifi {
+			compatible = "dummy,dit-hifi";
+			status = "okay";
+		};
+
+		sound {
+			compatible = "spear,spear-evb";
+			audio-controllers = <&spdif0 &spdif1 &i2s0 &i2s1>;
+			audio-codecs = <&incodec &outcodec &sta529 &sta529>;
+			codec_dai_name = "dir-hifi", "dit-hifi", "sta529-audio", "sta529-audio";
+			stream_name = "spdif-cap", "spdif-play", "i2s-play", "i2s-cap";
+			dai_name = "spdifin-pcm", "spdifout-pcm", "i2s0-pcm", "i2s1-pcm";
+			nr_controllers = <4>;
+		        status = "okay";
+		};
+
+		spdif0: spdif-in@d0100000 {
+			status = "okay";
+		};
+
+		spdif1: spdif-out@d0000000 {
+			status = "okay";
+		};
+
+		apb {
+			adc@e0080000 {
+				status = "okay";
+			};
+
+			i2s-play@b2400000 {
+				status = "okay";
+			};
+
+			i2s-rec@b2000000 {
+				status = "okay";
+			};
+
+			gpio0: gpio@e0600000 {
+			       status = "okay";
+			};
+
+			gpio1: gpio@e0680000 {
+			       status = "okay";
+			};
+
+			gpio@e2800000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@e0280000 {
+			       status = "okay";
+
+				sta529: sta529@1a {
+					compatible = "st,sta529";
+					reg = <0x1a>;
+				};
+			};
+
+			i2c1: i2c@b4000000 {
+			       status = "okay";
+
+				eeprom0@56 {
+					compatible = "st,eeprom";
+					reg = <0x56>;
+				};
+
+				stmpe801@41 {
+					compatible = "st,stmpe801";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x41>;
+					interrupts = <4 0x4>;
+					interrupt-parent = <&gpio0>;
+					irq-trigger = <0x2>;
+
+					stmpegpio: stmpe_gpio {
+						compatible = "st,stmpe-gpio";
+						gpio-controller;
+						#gpio-cells = <2>;
+					};
+				};
+			};
+
+			kbd@e0300000 {
+				linux,keymap = < 0x00000001
+						 0x00010002
+						 0x00020003
+						 0x00030004
+						 0x00040005
+						 0x00050006
+						 0x00060007
+						 0x00070008
+						 0x00080009
+						 0x0100000a
+						 0x0101000c
+						 0x0102000d
+						 0x0103000e
+						 0x0104000f
+						 0x01050010
+						 0x01060011
+						 0x01070012
+						 0x01080013
+						 0x02000014
+						 0x02010015
+						 0x02020016
+						 0x02030017
+						 0x02040018
+						 0x02050019
+						 0x0206001a
+						 0x0207001b
+						 0x0208001c
+						 0x0300001d
+						 0x0301001e
+						 0x0302001f
+						 0x03030020
+						 0x03040021
+						 0x03050022
+						 0x03060023
+						 0x03070024
+						 0x03080025
+						 0x04000026
+						 0x04010027
+						 0x04020028
+						 0x04030029
+						 0x0404002a
+						 0x0405002b
+						 0x0406002c
+						 0x0407002d
+						 0x0408002e
+						 0x0500002f
+						 0x05010030
+						 0x05020031
+						 0x05030032
+						 0x05040033
+						 0x05050034
+						 0x05060035
+						 0x05070036
+						 0x05080037
+						 0x06000038
+						 0x06010039
+						 0x0602003a
+						 0x0603003b
+						 0x0604003c
+						 0x0605003d
+						 0x0606003e
+						 0x0607003f
+						 0x06080040
+						 0x07000041
+						 0x07010042
+						 0x07020043
+						 0x07030044
+						 0x07040045
+						 0x07050046
+						 0x07060047
+						 0x07070048
+						 0x07080049
+						 0x0800004a
+						 0x0801004b
+						 0x0802004c
+						 0x0803004d
+						 0x0804004e
+						 0x0805004f
+						 0x08060050
+						 0x08070051
+						 0x08080052 >;
+			       autorepeat;
+			       st,mode = <0>;
+			       suspended_rate = <2000000>;
+			       status = "okay";
+			};
+
+			rtc@e0580000 {
+			       status = "okay";
+			};
+
+			serial@e0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b4100000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			spi0: spi@e0100000 {
+				status = "okay";
+				num-cs = <3>;
+				cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
+					   <&gpiopinctrl 85 0>;
+
+				flash@0 {
+					compatible = "m25p80";
+					reg = <0>;
+					spi-max-frequency = <12000000>;
+					spi-cpol;
+					spi-cpha;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0x2>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x11>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+				};
+
+				stmpe610@1 {
+					compatible = "st,stmpe610";
+					spi-max-frequency = <1000000>;
+					spi-cpha;
+					reg = <1>;
+					pl022,hierarchy = <0>;
+					pl022,interface = <0>;
+					pl022,slave-tx-disable;
+					pl022,com-mode = <0>;
+					pl022,rx-level-trig = <0>;
+					pl022,tx-level-trig = <0>;
+					pl022,ctrl-len = <0x7>;
+					pl022,wait-state = <0>;
+					pl022,duplex = <0>;
+					interrupts = <100 0>;
+					interrupt-parent = <&gpiopinctrl>;
+					irq-trigger = <0x2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					stmpe_touchscreen {
+						compatible = "st,stmpe-ts";
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <2>;
+						ts,settling = <2>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+			};
+
+			timer@ec800600 {
+				status = "okay";
+			};
+
+			wdt@ec800620 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear1340.dtsi b/arch/arm/boot/dts/st/spear1340.dtsi
new file mode 100644
index 000000000000..818886e11713
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear1340.dtsi
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for all SPEAr1340 SoCs
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/include/ "spear13xx.dtsi"
+
+/ {
+	compatible = "st,spear1340";
+
+	ahb {
+
+		spics: spics@e0700000{
+			compatible = "st,spear-spics-gpio";
+			reg = <0xe0700000 0x1000>;
+			st-spics,peripcfg-reg = <0x42c>;
+			st-spics,sw-enable-bit = <21>;
+			st-spics,cs-value-bit = <20>;
+			st-spics,cs-enable-mask = <3>;
+			st-spics,cs-enable-shift = <18>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		miphy0: miphy@eb800000 {
+			compatible = "st,spear1340-miphy";
+			reg = <0xeb800000 0x4000>;
+			misc = <&misc>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ahci0: ahci@b1000000 {
+			compatible = "snps,spear-ahci";
+			reg = <0xb1000000 0x10000>;
+			interrupts = <0 72 0x4>;
+			phys = <&miphy0 0>;
+			phy-names = "sata-phy";
+			status = "disabled";
+		};
+
+		pcie0: pcie@b1000000 {
+			compatible = "st,spear1340-pcie", "snps,dw-pcie";
+			reg = <0xb1000000 0x4000>, <0x80000000 0x20000>;
+			reg-names = "dbi", "config";
+			interrupts = <0 68 0x4>;
+			num-lanes = <1>;
+			phys = <&miphy0 1>;
+			phy-names = "pcie-phy";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x81000000 0 0	 0x80020000 0 0x00010000   /* downstream I/O */
+				0x82000000 0 0x80030000 0xc0030000 0 0x0ffd0000>; /* non-prefetchable memory */
+			bus-range = <0x00 0xff>;
+			status = "disabled";
+		};
+
+		i2s-play@b2400000 {
+			compatible = "snps,designware-i2s";
+			reg = <0xb2400000 0x10000>;
+			interrupt-names = "play_irq";
+			interrupts = <0 98 0x4
+				      0 99 0x4>;
+			play;
+			channel = <8>;
+			status = "disabled";
+		};
+
+		i2s-rec@b2000000 {
+			compatible = "snps,designware-i2s";
+			reg = <0xb2000000 0x10000>;
+			interrupt-names = "record_irq";
+			interrupts = <0 100  0x4
+				      0 101 0x4>;
+			record;
+			channel = <8>;
+			status = "disabled";
+		};
+
+		pinmux: pinmux@e0700000 {
+			compatible = "st,spear1340-pinmux";
+			reg = <0xe0700000 0x1000>;
+			#gpio-range-cells = <3>;
+		};
+
+		pwm: pwm@e0180000 {
+			compatible = "st,spear13xx-pwm";
+			reg = <0xe0180000 0x1000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
+
+		spdif-in@d0100000 {
+			compatible = "st,spdif-in";
+			reg = < 0xd0100000 0x20000
+				0xd0110000 0x10000 >;
+			interrupts = <0 84 0x4>;
+			status = "disabled";
+		};
+
+		spdif-out@d0000000 {
+			compatible = "st,spdif-out";
+			reg = <0xd0000000 0x20000>;
+			interrupts = <0 85 0x4>;
+			status = "disabled";
+		};
+
+		spi1: spi@5d400000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x5d400000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <0 99 0x4>;
+			status = "disabled";
+		};
+
+		apb {
+			i2c1: i2c@b4000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xb4000000 0x1000>;
+				interrupts = <0 104 0x4>;
+				write-16bit;
+				status = "disabled";
+			};
+
+			serial@b4100000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb4100000 0x1000>;
+				interrupts = <0 105 0x4>;
+				status = "disabled";
+				dmas = <&dwdma0 13 0 1>,
+					<&dwdma0 12 1 0>;
+				dma-names = "rx", "tx";
+			};
+
+			thermal@e07008c4 {
+				st,thermal-flags = <0x2a00>;
+			};
+
+			gpiopinctrl: gpio@e2800000 {
+				compatible = "st,spear-plgpio";
+				reg = <0xe2800000 0x1000>;
+				interrupts = <0 107 0x4>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinmux 0 0 252>;
+				status = "disabled";
+
+				st-plgpio,ngpio = <250>;
+				st-plgpio,wdata-reg = <0x40>;
+				st-plgpio,dir-reg = <0x00>;
+				st-plgpio,ie-reg = <0x80>;
+				st-plgpio,rdata-reg = <0x20>;
+				st-plgpio,mis-reg = <0xa0>;
+				st-plgpio,eit-reg = <0x60>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear13xx.dtsi b/arch/arm/boot/dts/st/spear13xx.dtsi
new file mode 100644
index 000000000000..913553367687
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear13xx.dtsi
@@ -0,0 +1,339 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for all SPEAr13xx SoCs
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&L2>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&L2>;
+		};
+	};
+
+	gic: interrupt-controller@ec801000 {
+		compatible = "arm,cortex-a9-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = < 0xec801000 0x1000 >,
+		      < 0xec800100 0x0100 >;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <0 6 0x04
+			      0 7 0x04>;
+	};
+
+	L2: cache-controller {
+		    compatible = "arm,pl310-cache";
+		    reg = <0xed000000 0x1000>;
+		    cache-unified;
+		    cache-level = <2>;
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyAMA0,115200";
+	};
+
+	cpufreq {
+		compatible = "st,cpufreq-spear";
+		cpufreq_tbl = < 166000
+				200000
+				250000
+				300000
+				400000
+				500000
+				600000 >;
+		status = "disabled";
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x50000000 0x50000000 0x10000000
+			  0x80000000 0x80000000 0x20000000
+			  0xb0000000 0xb0000000 0x22000000
+			  0xd8000000 0xd8000000 0x01000000
+			  0xe0000000 0xe0000000 0x10000000>;
+
+		sdhci@b3000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0xb3000000 0x100>;
+			interrupts = <0 28 0x4>;
+			status = "disabled";
+		};
+
+		cf@b2800000 {
+			compatible = "arasan,cf-spear1340";
+			reg = <0xb2800000 0x1000>;
+			interrupts = <0 29 0x4>;
+			status = "disabled";
+			dmas = <&dwdma0 0 0 0>;
+			dma-names = "data";
+		};
+
+		dwdma0: dma@ea800000 {
+			compatible = "snps,dma-spear1340";
+			reg = <0xea800000 0x1000>;
+			interrupts = <0 19 0x4>;
+			status = "disabled";
+
+			dma-channels = <8>;
+			#dma-cells = <3>;
+			dma-requests = <32>;
+			chan_allocation_order = <1>;
+			chan_priority = <1>;
+			block_size = <0xfff>;
+			dma-masters = <2>;
+			data-width = <8 8>;
+			multi-block = <1 1 1 1 1 1 1 1>;
+		};
+
+		dma@eb000000 {
+			compatible = "snps,dma-spear1340";
+			reg = <0xeb000000 0x1000>;
+			interrupts = <0 59 0x4>;
+			status = "disabled";
+
+			dma-requests = <32>;
+			dma-channels = <8>;
+			dma-masters = <2>;
+			#dma-cells = <3>;
+			chan_allocation_order = <1>;
+			chan_priority = <1>;
+			block_size = <0xfff>;
+			data-width = <8 8>;
+			multi-block = <1 1 1 1 1 1 1 1>;
+		};
+
+		fsmc: flash@b0000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xb0000000 0x1000	/* FSMC Register*/
+			       0xb0800000 0x0010	/* NAND Base DATA */
+			       0xb0820000 0x0010	/* NAND Base ADDR */
+			       0xb0810000 0x0010>;	/* NAND Base CMD */
+			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+			interrupts = <0 20 0x4
+				      0 21 0x4
+				      0 22 0x4
+				      0 23 0x4>;
+			st,mode = <2>;
+			status = "disabled";
+		};
+
+		gmac0: eth@e2000000 {
+			compatible = "st,spear600-gmac";
+			reg = <0xe2000000 0x8000>;
+			interrupts = <0 33 0x4
+				      0 34 0x4>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			status = "disabled";
+		};
+
+		pcm {
+			compatible = "st,pcm-audio";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		smi: flash@ea000000 {
+			compatible = "st,spear600-smi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xea000000 0x1000>;
+			interrupts = <0 30 0x4>;
+			status = "disabled";
+		};
+
+		ehci@e4800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe4800000 0x1000>;
+			interrupts = <0 64 0x4>;
+			usbh0_id = <0>;
+			status = "disabled";
+		};
+
+		ehci@e5800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe5800000 0x1000>;
+			interrupts = <0 66 0x4>;
+			usbh1_id = <1>;
+			status = "disabled";
+		};
+
+		ohci@e4000000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe4000000 0x1000>;
+			interrupts = <0 65 0x4>;
+			usbh0_id = <0>;
+			status = "disabled";
+		};
+
+		ohci@e5000000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe5000000 0x1000>;
+			interrupts = <0 67 0x4>;
+			usbh1_id = <1>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0x50000000 0x50000000 0x10000000
+				  0xb0000000 0xb0000000 0x10000000
+				  0xd0000000 0xd0000000 0x02000000
+				  0xd8000000 0xd8000000 0x01000000
+				  0xe0000000 0xe0000000 0x10000000>;
+
+			misc: syscon@e0700000 {
+				compatible = "st,spear1340-misc", "syscon";
+				reg = <0xe0700000 0x1000>;
+			};
+
+			gpio0: gpio@e0600000 {
+				compatible = "arm,pl061", "arm,primecell";
+				reg = <0xe0600000 0x1000>;
+				interrupts = <0 24 0x4>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			gpio1: gpio@e0680000 {
+				compatible = "arm,pl061", "arm,primecell";
+				reg = <0xe0680000 0x1000>;
+				interrupts = <0 25 0x4>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			kbd@e0300000 {
+				compatible = "st,spear300-kbd";
+				reg = <0xe0300000 0x1000>;
+				interrupts = <0 52 0x4>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@e0280000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xe0280000 0x1000>;
+				interrupts = <0 41 0x4>;
+				status = "disabled";
+			};
+
+			i2s@e0180000 {
+				compatible = "st,designware-i2s";
+				reg = <0xe0180000 0x1000>;
+				interrupt-names = "play_irq", "record_irq";
+				interrupts = <0 10 0x4
+					      0 11 0x4 >;
+				status = "disabled";
+			};
+
+			i2s@e0200000 {
+				compatible = "st,designware-i2s";
+				reg = <0xe0200000 0x1000>;
+				interrupt-names = "play_irq", "record_irq";
+				interrupts = <0 26 0x4
+					      0 53 0x4>;
+				status = "disabled";
+			};
+
+			spi0: spi@e0100000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xe0100000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <0 31 0x4>;
+				status = "disabled";
+				dmas = <&dwdma0 5 0 0>,
+					<&dwdma0 4 0 0>;
+				dma-names = "rx", "tx";
+			};
+
+			rtc@e0580000 {
+				compatible = "st,spear600-rtc";
+				reg = <0xe0580000 0x1000>;
+				interrupts = <0 36 0x4>;
+				status = "disabled";
+			};
+
+			serial@e0000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xe0000000 0x1000>;
+				interrupts = <0 35 0x4>;
+				status = "disabled";
+			};
+
+			adc@e0080000 {
+				compatible = "st,spear600-adc";
+				reg = <0xe0080000 0x1000>;
+				interrupts = <0 12 0x4>;
+				status = "disabled";
+			};
+
+			timer@e0380000 {
+				compatible = "st,spear-timer";
+				reg = <0xe0380000 0x400>;
+				interrupts = <0 37 0x4>;
+			};
+
+			timer@ec800600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xec800600 0x20>;
+				interrupts = <1 13 0x4>;
+				status = "disabled";
+			};
+
+			wdt@ec800620 {
+				compatible = "arm,cortex-a9-twd-wdt";
+				reg = <0xec800620 0x20>;
+				status = "disabled";
+			};
+
+			thermal@e07008c4 {
+				compatible = "st,thermal-spear1340";
+				reg = <0xe07008c4 0x4>;
+				thermal_flags = <0x7000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear300-evb.dts b/arch/arm/boot/dts/st/spear300-evb.dts
new file mode 100644
index 000000000000..303ef29fb805
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear300-evb.dts
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr300 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/dts-v1/;
+/include/ "spear300.dtsi"
+
+/ {
+	model = "ST SPEAr300 Evaluation Board";
+	compatible = "st,spear300-evb", "st,spear300";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@99000000 {
+			st,pinmux-mode = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				clcd {
+					st,pins = "clcd_pfmode_grp";
+					st,function = "clcd";
+				};
+				sdhci {
+					st,pins = "sdhci_4bit_grp";
+					st,function = "sdhci";
+				};
+				gpio1 {
+					st,pins = "gpio1_4_to_7_grp",
+						"gpio1_0_to_3_grp";
+					st,function = "gpio1";
+				};
+			};
+		};
+
+		clcd@60000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@94000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			cd-gpios = <&gpio1 0 0>;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio1: gpio@a9000000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			kbd@a0000000 {
+				linux,keymap = < 0x00000001
+						 0x00010002
+						 0x00020003
+						 0x00030004
+						 0x00040005
+						 0x00050006
+						 0x00060007
+						 0x00070008
+						 0x00080009
+						 0x0100000a
+						 0x0101000c
+						 0x0102000d
+						 0x0103000e
+						 0x0104000f
+						 0x01050010
+						 0x01060011
+						 0x01070012
+						 0x01080013
+						 0x02000014
+						 0x02010015
+						 0x02020016
+						 0x02030017
+						 0x02040018
+						 0x02050019
+						 0x0206001a
+						 0x0207001b
+						 0x0208001c
+						 0x0300001d
+						 0x0301001e
+						 0x0302001f
+						 0x03030020
+						 0x03040021
+						 0x03050022
+						 0x03060023
+						 0x03070024
+						 0x03080025
+						 0x04000026
+						 0x04010027
+						 0x04020028
+						 0x04030029
+						 0x0404002a
+						 0x0405002b
+						 0x0406002c
+						 0x0407002d
+						 0x0408002e
+						 0x0500002f
+						 0x05010030
+						 0x05020031
+						 0x05030032
+						 0x05040033
+						 0x05050034
+						 0x05060035
+						 0x05070036
+						 0x05080037
+						 0x06000038
+						 0x06010039
+						 0x0602003a
+						 0x0603003b
+						 0x0604003c
+						 0x0605003d
+						 0x0606003e
+						 0x0607003f
+						 0x06080040
+						 0x07000041
+						 0x07010042
+						 0x07020043
+						 0x07030044
+						 0x07040045
+						 0x07050046
+						 0x07060047
+						 0x07070048
+						 0x07080049
+						 0x0800004a
+						 0x0801004b
+						 0x0802004c
+						 0x0803004d
+						 0x0804004e
+						 0x0805004f
+						 0x08060050
+						 0x08070051
+						 0x08080052 >;
+			       autorepeat;
+			       st,mode = <0>;
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear300.dtsi b/arch/arm/boot/dts/st/spear300.dtsi
new file mode 100644
index 000000000000..f1135e887f7b
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear300.dtsi
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr300 SoC
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x60000000 0x60000000 0x50000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux@99000000 {
+			compatible = "st,spear300-pinmux";
+			reg = <0x99000000 0x1000>;
+		};
+
+		clcd@60000000 {
+			compatible = "arm,pl110", "arm,primecell";
+			reg = <0x60000000 0x1000>;
+			interrupts = <30>;
+			status = "disabled";
+		};
+
+		fsmc: flash@94000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x94000000 0x1000	/* FSMC Register */
+			       0x80000000 0x0010	/* NAND Base DATA */
+			       0x80020000 0x0010	/* NAND Base ADDR */
+			       0x80010000 0x0010>;	/* NAND Base CMD */
+			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <1>;
+			status = "disabled";
+		};
+
+		shirq: interrupt-controller@50000000 {
+			compatible = "st,spear300-shirq";
+			reg = <0x50000000 0x1000>;
+			interrupts = <28>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			gpio1: gpio@a9000000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xa9000000 0x1000>;
+				interrupts = <8>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			kbd@a0000000 {
+				compatible = "st,spear300-kbd";
+				reg = <0xa0000000 0x1000>;
+				interrupts = <7>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear310-evb.dts b/arch/arm/boot/dts/st/spear310-evb.dts
new file mode 100644
index 000000000000..ea0b53036f7b
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear310-evb.dts
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr310 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/dts-v1/;
+/include/ "spear310.dtsi"
+
+/ {
+	model = "ST SPEAr310 Evaluation Board";
+	compatible = "st,spear310-evb", "st,spear310";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b4000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				gpio0 {
+					st,pins = "gpio0_pin0_grp",
+						"gpio0_pin1_grp",
+						"gpio0_pin2_grp",
+						"gpio0_pin3_grp",
+						"gpio0_pin4_grp",
+						"gpio0_pin5_grp";
+					st,function = "gpio0";
+				};
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				emi {
+					st,pins = "emi_cs_0_to_5_grp";
+					st,function = "emi";
+				};
+				fsmc {
+					st,pins = "fsmc_grp";
+					st,function = "fsmc";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				uart3 {
+					st,pins = "uart3_grp";
+					st,function = "uart3";
+				};
+				uart4 {
+					st,pins = "uart4_grp";
+					st,function = "uart4";
+				};
+				uart5 {
+					st,pins = "uart5_grp";
+					st,function = "uart5";
+				};
+			};
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@44000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b2000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b2080000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b2100000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b2180000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@b2200000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear310.dtsi b/arch/arm/boot/dts/st/spear310.dtsi
new file mode 100644
index 000000000000..ce08d8820940
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear310.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr310 SoC
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x10000000
+			  0xb0000000 0xb0000000 0x10000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux: pinmux@b4000000 {
+			compatible = "st,spear310-pinmux";
+			reg = <0xb4000000 0x1000>;
+			#gpio-range-cells = <3>;
+		};
+
+		fsmc: flash@44000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x44000000 0x1000	/* FSMC Register */
+			       0x40000000 0x0010	/* NAND Base DATA */
+			       0x40020000 0x0010	/* NAND Base ADDR */
+			       0x40010000 0x0010>;	/* NAND Base CMD */
+			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+			status = "disabled";
+		};
+
+		shirq: interrupt-controller@b4000000 {
+			compatible = "st,spear310-shirq";
+			reg = <0xb4000000 0x1000>;
+			interrupts = <28 29 30 1>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xb0000000 0xb0000000 0x10000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			serial@b2000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2000000 0x1000>;
+				interrupts = <8>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@b2080000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2080000 0x1000>;
+				interrupts = <9>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@b2100000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2100000 0x1000>;
+				interrupts = <10>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@b2180000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2180000 0x1000>;
+				interrupts = <11>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@b2200000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xb2200000 0x1000>;
+				interrupts = <12>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			gpiopinctrl: gpio@b4000000 {
+				compatible = "st,spear-plgpio";
+				reg = <0xb4000000 0x1000>;
+				regmap = <&pinmux>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinmux 0 0 102>;
+				status = "disabled";
+
+				st-plgpio,ngpio = <102>;
+				st-plgpio,enb-reg = <0x10>;
+				st-plgpio,wdata-reg = <0x20>;
+				st-plgpio,dir-reg = <0x30>;
+				st-plgpio,ie-reg = <0x50>;
+				st-plgpio,rdata-reg = <0x40>;
+				st-plgpio,mis-reg = <0x60>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear320-evb.dts b/arch/arm/boot/dts/st/spear320-evb.dts
new file mode 100644
index 000000000000..3c026d021c92
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear320-evb.dts
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+	model = "ST SPEAr320 Evaluation Board";
+	compatible = "st,spear320-evb", "st,spear320";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b3000000 {
+			st,pinmux-mode = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				mii0 {
+					st,pins = "mii0_grp";
+					st,function = "mii0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				sdhci {
+					st,pins = "sdhci_cd_51_grp";
+					st,function = "sdhci";
+				};
+				i2s {
+					st,pins = "i2s_grp";
+					st,function = "i2s";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				can0 {
+					st,pins = "can0_grp";
+					st,function = "can0";
+				};
+				can1 {
+					st,pins = "can1_grp";
+					st,function = "can1";
+				};
+				mii2 {
+					st,pins = "mii2_grp";
+					st,function = "mii2";
+				};
+				pwm0_1 {
+					st,pins = "pwm0_1_pin_37_38_grp";
+					st,function = "pwm0_1";
+				};
+			};
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		fsmc: flash@4c000000 {
+			status = "okay";
+		};
+
+		gmac: eth@e0800000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			power-gpio = <&gpiopinctrl 61 1>;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		spi1: spi@a5000000 {
+			status = "okay";
+		};
+
+		spi2: spi@a6000000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio@b3000000 {
+			       status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+			       status = "okay";
+			};
+
+			i2c1: i2c@a7000000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a3000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a4000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear320-hmi.dts b/arch/arm/boot/dts/st/spear320-hmi.dts
new file mode 100644
index 000000000000..721e5ee7b680
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear320-hmi.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320 Evaluation Baord
+ *
+ * Copyright 2012 Shiraz Hashim <shiraz.linux.kernel@gmail.com>
+ */
+
+/dts-v1/;
+/include/ "spear320.dtsi"
+
+/ {
+	model = "ST SPEAr320 HMI Board";
+	compatible = "st,spear320-hmi", "st,spear320";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		pinmux@b3000000 {
+			st,pinmux-mode = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			state_default: pinmux {
+				i2c0 {
+					st,pins = "i2c0_grp";
+					st,function = "i2c0";
+				};
+				ssp0 {
+					st,pins = "ssp0_grp";
+					st,function = "ssp0";
+				};
+				uart0 {
+					st,pins = "uart0_grp";
+					st,function = "uart0";
+				};
+				clcd {
+					st,pins = "clcd_grp";
+					st,function = "clcd";
+				};
+				fsmc {
+					st,pins = "fsmc_8bit_grp";
+					st,function = "fsmc";
+				};
+				sdhci {
+					st,pins = "sdhci_cd_12_grp";
+					st,function = "sdhci";
+				};
+				i2s {
+					st,pins = "i2s_grp";
+					st,function = "i2s";
+				};
+				uart1 {
+					st,pins = "uart1_grp";
+					st,function = "uart1";
+				};
+				uart2 {
+					st,pins = "uart2_grp";
+					st,function = "uart2";
+				};
+				can0 {
+					st,pins = "can0_grp";
+					st,function = "can0";
+				};
+				can1 {
+					st,pins = "can1_grp";
+					st,function = "can1";
+				};
+				mii0_1 {
+					st,pins = "rmii0_1_grp";
+					st,function = "mii0_1";
+				};
+				pwm0_1 {
+					st,pins = "pwm0_1_pin_37_38_grp";
+					st,function = "pwm0_1";
+				};
+				pwm2 {
+					st,pins = "pwm2_pin_34_grp";
+					st,function = "pwm2";
+				};
+			};
+		};
+
+		clcd@90000000 {
+			status = "okay";
+		};
+
+		dma@fc400000 {
+			status = "okay";
+		};
+
+		ehci@e1800000 {
+			status = "okay";
+		};
+
+		fsmc: flash@4c000000 {
+			status = "okay";
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x80000>;
+			};
+			partition@80000 {
+				label = "u-boot";
+				reg = <0x80000 0x140000>;
+			};
+			partition@1C0000 {
+				label = "environment";
+				reg = <0x1C0000 0x40000>;
+			};
+			partition@200000 {
+				label = "dtb";
+				reg = <0x200000 0x40000>;
+			};
+			partition@240000 {
+				label = "linux";
+				reg = <0x240000 0xC00000>;
+			};
+			partition@E40000 {
+				label = "rootfs";
+				reg = <0xE40000 0x0>;
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			button@1 {
+				label = "user button 1";
+				linux,code = <0x100>;
+				gpios = <&stmpegpio 3 0x4>;
+				debounce-interval = <20>;
+				wakeup-source;
+			};
+
+			button@2 {
+				label = "user button 2";
+				linux,code = <0x200>;
+				gpios = <&stmpegpio 2 0x4>;
+				debounce-interval = <20>;
+				wakeup-source;
+			};
+		};
+
+		ohci@e1900000 {
+			status = "okay";
+		};
+
+		ohci@e2100000 {
+			status = "okay";
+		};
+
+		pwm: pwm@a8000000 {
+			status = "okay";
+		};
+
+		sdhci@70000000 {
+			power-gpio = <&gpiopinctrl 50 1>;
+			power_always_enb;
+			status = "okay";
+		};
+
+		smi: flash@fc000000 {
+			status = "okay";
+			clock-rate = <50000000>;
+
+			flash@f8000000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0xf8000000 0x800000>;
+				st,smi-fast-mode;
+
+				partition@0 {
+					label = "xloader";
+					reg = <0x0 0x10000>;
+				};
+				partition@10000 {
+					label = "u-boot";
+					reg = <0x10000 0x50000>;
+				};
+				partition@60000 {
+					label = "environment";
+					reg = <0x60000 0x10000>;
+				};
+				partition@70000 {
+					label = "dtb";
+					reg = <0x70000 0x10000>;
+				};
+				partition@80000 {
+					label = "linux";
+					reg = <0x80000 0x310000>;
+				};
+				partition@390000 {
+					label = "rootfs";
+					reg = <0x390000 0x0>;
+				};
+			};
+		};
+
+		spi0: spi@d0100000 {
+			status = "okay";
+		};
+
+		spi1: spi@a5000000 {
+			status = "okay";
+		};
+
+		spi2: spi@a6000000 {
+			status = "okay";
+		};
+
+		usbd@e1100000 {
+			status = "okay";
+		};
+
+		apb {
+			gpio0: gpio@fc980000 {
+			       status = "okay";
+			};
+
+			gpio@b3000000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@d0180000 {
+				status = "okay";
+
+				stmpe811@41 {
+					compatible = "st,stmpe811";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x41>;
+					irq-gpios = <&gpiopinctrl 29 0x4>;
+					id = <0>;
+					blocks = <0x5>;
+					irq-trigger = <0x1>;
+
+					stmpegpio: stmpe-gpio {
+						compatible = "st,stmpe-gpio";
+						reg = <0>;
+						gpio-controller;
+						#gpio-cells = <2>;
+						gpio,norequest-mask = <0xF3>;
+					};
+
+					stmpe610-ts {
+						compatible = "stmpe,ts";
+						reg = <0>;
+						ts,sample-time = <4>;
+						ts,mod-12b = <1>;
+						ts,ref-sel = <0>;
+						ts,adc-freq = <1>;
+						ts,ave-ctrl = <1>;
+						ts,touch-det-delay = <3>;
+						ts,settling = <4>;
+						ts,fraction-z = <7>;
+						ts,i-drive = <1>;
+					};
+				};
+			};
+
+			i2c1: i2c@a7000000 {
+			       status = "okay";
+			};
+
+			rtc@fc900000 {
+			       status = "okay";
+			};
+
+			serial@d0000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a3000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			serial@a4000000 {
+			       status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <>;
+			};
+
+			wdt@fc880000 {
+			       status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear320.dtsi b/arch/arm/boot/dts/st/spear320.dtsi
new file mode 100644
index 000000000000..56f141297ea3
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear320.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320 SoC
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/include/ "spear3xx.dtsi"
+
+/ {
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0x40000000 0x40000000 0x80000000
+			  0xd0000000 0xd0000000 0x30000000>;
+
+		pinmux: pinmux@b3000000 {
+			compatible = "st,spear320-pinmux";
+			reg = <0xb3000000 0x1000>;
+			#gpio-range-cells = <3>;
+		};
+
+		clcd@90000000 {
+			compatible = "arm,pl110", "arm,primecell";
+			reg = <0x90000000 0x1000>;
+			interrupts = <8>;
+			interrupt-parent = <&shirq>;
+			status = "disabled";
+		};
+
+		fsmc: flash@4c000000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x4c000000 0x1000	/* FSMC Register */
+			       0x50000000 0x0010	/* NAND Base DATA */
+			       0x50020000 0x0010	/* NAND Base ADDR */
+			       0x50010000 0x0010>;	/* NAND Base CMD */
+			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+			status = "disabled";
+		};
+
+		sdhci@70000000 {
+			compatible = "st,sdhci-spear";
+			reg = <0x70000000 0x100>;
+			interrupts = <10>;
+			interrupt-parent = <&shirq>;
+			status = "disabled";
+		};
+
+		shirq: interrupt-controller@b3000000 {
+			compatible = "st,spear320-shirq";
+			reg = <0xb3000000 0x1000>;
+			interrupts = <30 28 29 1>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+		};
+
+		spi1: spi@a5000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa5000000 0x1000>;
+			interrupts = <15>;
+			interrupt-parent = <&shirq>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@a6000000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xa6000000 0x1000>;
+			interrupts = <16>;
+			interrupt-parent = <&shirq>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@a8000000 {
+			compatible = "st,spear-pwm";
+			reg = <0xa8000000 0x1000>;
+			#pwm-cells = <2>;
+			status = "disabled";
+                };
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xa0000000 0xa0000000 0x20000000
+				  0xd0000000 0xd0000000 0x30000000>;
+
+			i2c1: i2c@a7000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xa7000000 0x1000>;
+				interrupts = <21>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@a3000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa3000000 0x1000>;
+				interrupts = <13>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			serial@a4000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xa4000000 0x1000>;
+				interrupts = <14>;
+				interrupt-parent = <&shirq>;
+				status = "disabled";
+			};
+
+			gpiopinctrl: gpio@b3000000 {
+				compatible = "st,spear-plgpio";
+				reg = <0xb3000000 0x1000>;
+				regmap = <&pinmux>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinmux 0 0 102>;
+				status = "disabled";
+
+				st-plgpio,ngpio = <102>;
+				st-plgpio,enb-reg = <0x24>;
+				st-plgpio,wdata-reg = <0x34>;
+				st-plgpio,dir-reg = <0x44>;
+				st-plgpio,ie-reg = <0x64>;
+				st-plgpio,rdata-reg = <0x54>;
+				st-plgpio,mis-reg = <0x84>;
+				st-plgpio,eit-reg = <0x94>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear320s.dtsi b/arch/arm/boot/dts/st/spear320s.dtsi
new file mode 100644
index 000000000000..133236dc190d
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear320s.dtsi
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320s SoC
+ *
+ * Copyright 2021 Herve Codina <herve.codina@bootlin.com>
+ */
+
+/include/ "spear320.dtsi"
+
+/ {
+	ahb {
+		apb {
+			gpiopinctrl: gpio@b3000000 {
+				/*
+				 * The "RM0321 SPEAr320s address and map
+				 * registers" document mentions interrupt 6
+				 * (NPGIO_INTR) for the PL_GPIO interrupt.
+				 */
+				interrupts = <6>;
+				interrupt-parent = <&shirq>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear3xx.dtsi b/arch/arm/boot/dts/st/spear3xx.dtsi
new file mode 100644
index 000000000000..cc88ebe7a60c
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear3xx.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for all SPEAr3xx SoCs
+ *
+ * Copyright 2012 Viresh Kumar <vireshk@kernel.org>
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&vic>;
+
+	cpus {
+		#address-cells = <0>;
+		#size-cells = <0>;
+
+		cpu {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+		vic: interrupt-controller@f1100000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xf1100000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic>;
+			interrupts = <8>;
+			status = "disabled";
+		};
+
+		gmac: eth@e0800000 {
+			compatible = "snps,dwmac-3.40a";
+			reg = <0xe0800000 0x8000>;
+			interrupts = <23 22>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			phy-mode = "mii";
+			status = "disabled";
+		};
+
+		smi: flash@fc000000 {
+			compatible = "st,spear600-smi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xfc000000 0x1000>;
+			interrupts = <9>;
+			status = "disabled";
+		};
+
+		spi0: spi@d0100000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0xd0100000 0x1000>;
+			interrupts = <20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		ehci@e1800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe1800000 0x1000>;
+			interrupts = <26>;
+			status = "disabled";
+		};
+
+		ohci@e1900000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe1900000 0x1000>;
+			interrupts = <25>;
+			status = "disabled";
+		};
+
+		ohci@e2100000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe2100000 0x1000>;
+			interrupts = <27>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+			gpio0: gpio@fc980000 {
+				compatible = "arm,pl061", "arm,primecell";
+				reg = <0xfc980000 0x1000>;
+				interrupts = <11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@d0180000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xd0180000 0x1000>;
+				interrupts = <21>;
+				status = "disabled";
+			};
+
+			rtc@fc900000 {
+				compatible = "st,spear600-rtc";
+				reg = <0xfc900000 0x1000>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
+			serial@d0000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xd0000000 0x1000>;
+				interrupts = <19>;
+				status = "disabled";
+			};
+
+			wdt@fc880000 {
+				compatible = "arm,sp805", "arm,primecell";
+				reg = <0xfc880000 0x1000>;
+				interrupts = <12>;
+				status = "disabled";
+			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupts = <2>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/spear600-evb.dts b/arch/arm/boot/dts/st/spear600-evb.dts
new file mode 100644
index 000000000000..a25b86d149ad
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear600-evb.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Stefan Roese <sr@denx.de>
+ */
+
+/dts-v1/;
+/include/ "spear600.dtsi"
+
+/ {
+	model = "ST SPEAr600 Evaluation Board";
+	compatible = "st,spear600-evb", "st,spear600";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x10000000>;
+	};
+};
+
+&clcd {
+	status = "okay";
+};
+
+&dmac {
+	status = "okay";
+};
+
+&ehci_usb0 {
+	status = "okay";
+};
+
+&ehci_usb1 {
+	status = "okay";
+};
+
+&gmac {
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&ohci_usb0 {
+	status = "okay";
+};
+
+&ohci_usb1 {
+	status = "okay";
+};
+
+&smi {
+	status = "okay";
+	clock-rate = <50000000>;
+
+	flash@f8000000 {
+		reg = <0xf8000000 0x800000>;
+		st,smi-fast-mode;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "xloader";
+				reg = <0x0 0x10000>;
+			};
+			partition@10000 {
+				label = "u-boot";
+				reg = <0x10000 0x50000>;
+			};
+			partition@60000 {
+				label = "environment";
+				reg = <0x60000 0x10000>;
+			};
+			partition@70000 {
+				label = "dtb";
+				reg = <0x70000 0x10000>;
+			};
+			partition@80000 {
+				label = "linux";
+				reg = <0x80000 0x310000>;
+			};
+			partition@390000 {
+				label = "rootfs";
+				reg = <0x390000 0x0>;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&i2c {
+	clock-frequency = <400000>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/spear600.dtsi b/arch/arm/boot/dts/st/spear600.dtsi
new file mode 100644
index 000000000000..6b67c0ceaed9
--- /dev/null
+++ b/arch/arm/boot/dts/st/spear600.dtsi
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Stefan Roese <sr@denx.de>
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "st,spear600";
+
+	cpus {
+		#address-cells = <0>;
+		#size-cells = <0>;
+
+		cpu {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+		vic0: interrupt-controller@f1100000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xf1100000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		vic1: interrupt-controller@f1000000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xf1000000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		clcd: clcd@fc200000 {
+			compatible = "arm,pl110", "arm,primecell";
+			reg = <0xfc200000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <13>;
+			status = "disabled";
+		};
+
+		dmac: dma@fc400000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0xfc400000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <10>;
+			status = "disabled";
+		};
+
+		gmac: ethernet@e0800000 {
+			compatible = "st,spear600-gmac";
+			reg = <0xe0800000 0x8000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <24 23>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			phy-mode = "gmii";
+			status = "disabled";
+		};
+
+		fsmc: flash@d1800000 {
+			compatible = "st,spear600-fsmc-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xd1800000 0x1000	/* FSMC Register */
+			       0xd2000000 0x0010	/* NAND Base DATA */
+			       0xd2020000 0x0010	/* NAND Base ADDR */
+			       0xd2010000 0x0010>;	/* NAND Base CMD */
+			reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+			status = "disabled";
+		};
+
+		smi: flash@fc000000 {
+			compatible = "st,spear600-smi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0xfc000000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <12>;
+			status = "disabled";
+		};
+
+		ehci_usb0: ehci@e1800000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe1800000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+			status = "disabled";
+		};
+
+		ehci_usb1: ehci@e2000000 {
+			compatible = "st,spear600-ehci", "usb-ehci";
+			reg = <0xe2000000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <29>;
+			status = "disabled";
+		};
+
+		ohci_usb0: ohci@e1900000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe1900000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <26>;
+			status = "disabled";
+		};
+
+		ohci_usb1: ohci@e2100000 {
+			compatible = "st,spear600-ohci", "usb-ohci";
+			reg = <0xe2100000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <28>;
+			status = "disabled";
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			ranges = <0xd0000000 0xd0000000 0x30000000>;
+
+			uart0: serial@d0000000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xd0000000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <24>;
+				status = "disabled";
+			};
+
+			uart1: serial@d0080000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0xd0080000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <25>;
+				status = "disabled";
+			};
+
+			/* local/cpu GPIO */
+			gpio0: gpio@f0100000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xf0100000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <18>;
+			};
+
+			/* basic GPIO */
+			gpio1: gpio@fc980000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xfc980000 0x1000>;
+				interrupt-parent = <&vic1>;
+				interrupts = <19>;
+			};
+
+			/* appl GPIO */
+			gpio2: gpio@d8100000 {
+				#gpio-cells = <2>;
+				compatible = "arm,pl061", "arm,primecell";
+				gpio-controller;
+				reg = <0xd8100000 0x1000>;
+				interrupt-parent = <&vic1>;
+				interrupts = <4>;
+			};
+
+			i2c: i2c@d0200000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,designware-i2c";
+				reg = <0xd0200000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <28>;
+				status = "disabled";
+			};
+
+			rtc: rtc@fc900000 {
+				compatible = "st,spear600-rtc";
+				reg = <0xfc900000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <10>;
+				status = "disabled";
+			};
+
+			timer@f0000000 {
+				compatible = "st,spear-timer";
+				reg = <0xf0000000 0x400>;
+				interrupt-parent = <&vic0>;
+				interrupts = <16>;
+			};
+
+			adc: adc@d820b000 {
+				compatible = "st,spear600-adc";
+				reg = <0xd820b000 0x1000>;
+				interrupt-parent = <&vic1>;
+				interrupts = <6>;
+				status = "disabled";
+			};
+
+			ssp1: spi@d0100000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd0100000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic0>;
+				interrupts = <26>;
+				status = "disabled";
+			};
+
+			ssp2: spi@d0180000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd0180000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic0>;
+				interrupts = <27>;
+				status = "disabled";
+			};
+
+			ssp3: spi@d8180000 {
+				compatible = "arm,pl022", "arm,primecell";
+				reg = <0xd8180000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupt-parent = <&vic1>;
+				interrupts = <5>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/st-pincfg.h b/arch/arm/boot/dts/st/st-pincfg.h
new file mode 100644
index 000000000000..d80551202292
--- /dev/null
+++ b/arch/arm/boot/dts/st/st-pincfg.h
@@ -0,0 +1,72 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ST_PINCFG_H_
+#define _ST_PINCFG_H_
+
+/* Alternate functions */
+#define ALT1	1
+#define ALT2	2
+#define ALT3	3
+#define ALT4	4
+#define ALT5	5
+#define ALT6	6
+#define ALT7	7
+
+/* Output enable */
+#define OE			(1 << 27)
+/* Pull Up */
+#define PU			(1 << 26)
+/* Open Drain */
+#define OD			(1 << 25)
+#define RT			(1 << 23)
+#define INVERTCLK		(1 << 22)
+#define CLKNOTDATA		(1 << 21)
+#define DOUBLE_EDGE		(1 << 20)
+#define CLK_A			(0 << 18)
+#define CLK_B			(1 << 18)
+#define CLK_C			(2 << 18)
+#define CLK_D			(3 << 18)
+
+/* User-frendly defines for Pin Direction */
+		/* oe = 0, pu = 0, od = 0 */
+#define IN			(0)
+		/* oe = 0, pu = 1, od = 0 */
+#define IN_PU			(PU)
+		/* oe = 1, pu = 0, od = 0 */
+#define OUT			(OE)
+		/* oe = 1, pu = 0, od = 1 */
+#define BIDIR			(OE | OD)
+		/* oe = 1, pu = 1, od = 1 */
+#define BIDIR_PU		(OE | PU | OD)
+
+/* RETIME_TYPE */
+/*
+ * B Mode
+ * Bypass retime with optional delay parameter
+ */
+#define BYPASS		(0)
+/*
+ * R0, R1, R0D, R1D modes
+ * single-edge data non inverted clock, retime data with clk
+ */
+#define SE_NICLK_IO	(RT)
+/*
+ * RIV0, RIV1, RIV0D, RIV1D modes
+ * single-edge data inverted clock, retime data with clk
+ */
+#define SE_ICLK_IO	(RT | INVERTCLK)
+/*
+ * R0E, R1E, R0ED, R1ED modes
+ * double-edge data, retime data with clk
+ */
+#define DE_IO		(RT | DOUBLE_EDGE)
+/*
+ * CIV0, CIV1 modes with inverted clock
+ * Retiming the clk pins will park clock & reduce the noise within the core.
+ */
+#define ICLK		(RT | CLKNOTDATA | INVERTCLK)
+/*
+ * CLK0, CLK1 modes with non-inverted clock
+ * Retiming the clk pins will park clock & reduce the noise within the core.
+ */
+#define NICLK		(RT | CLKNOTDATA)
+#endif /* _ST_PINCFG_H_ */
diff --git a/arch/arm/boot/dts/st/ste-ab8500.dtsi b/arch/arm/boot/dts/st/ste-ab8500.dtsi
new file mode 100644
index 000000000000..dd30d08ccb9b
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ab8500.dtsi
@@ -0,0 +1,392 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/clock/ste-ab8500.h>
+
+/ {
+	/* Essential housekeeping hardware monitors */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&gpadc 0x02>, /* Battery temperature */
+			    <&gpadc 0x03>, /* Main charger voltage */
+			    <&gpadc 0x08>, /* Main battery voltage */
+			    <&gpadc 0x09>, /* VBUS */
+			    <&gpadc 0x0a>, /* Main charger current */
+			    <&gpadc 0x0b>, /* USB charger current */
+			    <&gpadc 0x0c>, /* Backup battery voltage */
+			    <&gpadc 0x0d>, /* Die temperature */
+			    <&gpadc 0x12>; /* Crystal temperature */
+	};
+
+	soc {
+		prcmu@80157000 {
+			ab8500 {
+				compatible = "stericsson,ab8500";
+				interrupt-parent = <&intc>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ab8500_clock: clock-controller {
+					compatible = "stericsson,ab8500-clk";
+					#clock-cells = <1>;
+				};
+
+				ab8500_gpio: gpio {
+					compatible = "stericsson,ab8500-gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				rtc {
+					compatible = "stericsson,ab8500-rtc";
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "60S", "ALARM";
+				};
+
+				gpadc: adc {
+					compatible = "stericsson,ab8500-gpadc";
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
+						     <39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "HW_CONV_END", "SW_CONV_END";
+					vddadc-supply = <&ab8500_ldo_tvout_reg>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#io-channel-cells = <1>;
+
+					/* GPADC channels */
+					bat_ctrl: channel@1 {
+						reg = <0x01>;
+					};
+					btemp_ball: channel@2 {
+						reg = <0x02>;
+					};
+					main_charger_v: channel@3 {
+						reg = <0x03>;
+					};
+					acc_detect1: channel@4 {
+						reg = <0x04>;
+					};
+					acc_detect2: channel@5 {
+						reg = <0x05>;
+					};
+					adc_aux1: channel@6 {
+						reg = <0x06>;
+					};
+					adc_aux2: channel@7 {
+						reg = <0x07>;
+					};
+					main_batt_v: channel@8 {
+						reg = <0x08>;
+					};
+					vbus_v: channel@9 {
+						reg = <0x09>;
+					};
+					main_charger_c: channel@a {
+						reg = <0x0a>;
+					};
+					usb_charger_c: channel@b {
+						reg = <0x0b>;
+					};
+					bk_bat_v: channel@c {
+						reg = <0x0c>;
+					};
+					die_temp: channel@d {
+						reg = <0x0d>;
+					};
+					usb_id: channel@e {
+						reg = <0x0e>;
+					};
+					xtal_temp: channel@12 {
+						reg = <0x12>;
+					};
+					vbat_true_meas: channel@13 {
+						reg = <0x13>;
+					};
+					bat_ctrl_and_ibat: channel@1c {
+						reg = <0x1c>;
+					};
+					vbat_meas_and_ibat: channel@1d {
+						reg = <0x1d>;
+					};
+					vbat_true_meas_and_ibat: channel@1e {
+						reg = <0x1e>;
+					};
+					bat_temp_and_ibat: channel@1f {
+						reg = <0x1f>;
+					};
+				};
+
+				thermal {
+					compatible = "stericsson,abx500-temp";
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ABX500_TEMP_WARM";
+				};
+
+				ab8500_fg {
+					compatible = "stericsson,ab8500-fg";
+					interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+						     <8 IRQ_TYPE_LEVEL_HIGH>,
+						     <28 IRQ_TYPE_LEVEL_HIGH>,
+						     <27 IRQ_TYPE_LEVEL_HIGH>,
+						     <26 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "NCONV_ACCU",
+							  "BATT_OVV",
+							  "LOW_BAT_F",
+							  "CC_INT_CALIB",
+							  "CCEOC";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x08>;
+					io-channel-names = "main_bat_v";
+				};
+
+				ab8500_btemp {
+					compatible = "stericsson,ab8500-btemp";
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH>,
+						     <80 IRQ_TYPE_LEVEL_HIGH>,
+						     <83 IRQ_TYPE_LEVEL_HIGH>,
+						     <81 IRQ_TYPE_LEVEL_HIGH>,
+						     <82 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "BAT_CTRL_INDB",
+							  "BTEMP_LOW",
+							  "BTEMP_HIGH",
+							  "BTEMP_LOW_MEDIUM",
+							  "BTEMP_MEDIUM_HIGH";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x02>,
+						      <&gpadc 0x01>;
+					io-channel-names = "btemp_ball",
+							"bat_ctrl";
+				};
+
+				ab8500_charger {
+					compatible = "stericsson,ab8500-charger";
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
+						     <11 IRQ_TYPE_LEVEL_HIGH>,
+						     <0 IRQ_TYPE_LEVEL_HIGH>,
+						     <107 IRQ_TYPE_LEVEL_HIGH>,
+						     <106 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <105 IRQ_TYPE_LEVEL_HIGH>,
+						     <104 IRQ_TYPE_LEVEL_HIGH>,
+						     <89 IRQ_TYPE_LEVEL_HIGH>,
+						     <22 IRQ_TYPE_LEVEL_HIGH>,
+						     <21 IRQ_TYPE_LEVEL_HIGH>,
+						     <16 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "MAIN_CH_UNPLUG_DET",
+							  "MAIN_CHARGE_PLUG_DET",
+							  "MAIN_EXT_CH_NOT_OK",
+							  "MAIN_CH_TH_PROT_R",
+							  "MAIN_CH_TH_PROT_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_CH_TH_PROT_R",
+							  "USB_CH_TH_PROT_F",
+							  "USB_CHARGER_NOT_OKR",
+							  "VBUS_OVV",
+							  "CH_WD_EXP",
+							  "VBUS_CH_DROP_END";
+					monitored-battery = <&battery>;
+					vddadc-supply = <&ab8500_ldo_tvout_reg>;
+					io-channels = <&gpadc 0x03>,
+						      <&gpadc 0x0a>,
+						      <&gpadc 0x09>,
+						      <&gpadc 0x0b>;
+					io-channel-names = "main_charger_v",
+							"main_charger_c",
+							"vbus_v",
+							"usb_charger_c";
+				};
+
+				ab8500_chargalg {
+					compatible = "stericsson,ab8500-chargalg";
+					monitored-battery = <&battery>;
+				};
+
+				ab8500_usb: phy {
+					compatible = "stericsson,ab8500-usb";
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ID_WAKEUP_R",
+							  "ID_WAKEUP_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_ADP_PROBE_PLUG",
+							  "USB_ADP_PROBE_UNPLUG";
+					vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+					v-ape-supply = <&db8500_vape_reg>;
+					musb_1v8-supply = <&db8500_vsmps2_reg>;
+					clocks = <&prcmu_clk PRCMU_SYSCLK>;
+					clock-names = "sysclk";
+					#phy-cells = <0>;
+				};
+
+				key {
+					compatible = "stericsson,ab8500-poweron-key";
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+				};
+
+				ab8500-sysctrl {
+					compatible = "stericsson,ab8500-sysctrl";
+				};
+
+				pwm@1 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				pwm@2 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <2>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				pwm@3 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <3>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				codec: codec {
+					compatible = "stericsson,ab8500-codec";
+
+					V-AUD-supply = <&ab8500_ldo_audio_reg>;
+					V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
+					V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
+					V-DMIC-supply = <&ab8500_ldo_dmic_reg>;
+
+					clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
+					clock-names = "audioclk";
+
+					stericsson,earpeice-cmv = <950>; /* Units in mV. */
+				};
+
+				ext_regulators: regulator-external {
+					compatible = "stericsson,ab8500-ext-regulator";
+
+					ab8500_ext1_reg: ab8500_ext1 {
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext2_reg: ab8500_ext2 {
+						regulator-min-microvolt = <1360000>;
+						regulator-max-microvolt = <1360000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext3_reg: ab8500_ext3 {
+						regulator-min-microvolt = <3400000>;
+						regulator-max-microvolt = <3400000>;
+						regulator-boot-on;
+					};
+				};
+
+				regulator {
+					compatible = "stericsson,ab8500-regulator";
+					vin-supply = <&ab8500_ext3_reg>;
+
+					// supplies to the display/camera
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-boot-on;
+						/* BUG: If turned off MMC will be affected. */
+						regulator-always-on;
+					};
+
+					// supplies to the on-board eMMC
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					// supply for VAUX3; SDcard slots
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					// supply for v-intcore12; VINTCORE12 LDO
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+					};
+
+					// supply for tvout; gpadc; TVOUT LDO
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+					};
+
+					// supply for ab8500-vaudio; VAUDIO LDO
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+					};
+
+					// supply for v-anamic1 VAMIC1 LDO
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+					};
+
+					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+					};
+
+					// supply for v-dmic; VDMIC LDO
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+					};
+
+					// supply for U8500 CSI/DSI; VANA LDO
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+					};
+				};
+			};
+		};
+
+		sound {
+			stericsson,audio-codec = <&codec>;
+			clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
+			clock-names = "sysclk", "ulpclk", "intclk";
+		};
+
+		mcde@a0350000 {
+			vana-supply = <&ab8500_ldo_ana_reg>;
+
+			dsi@a0351000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0352000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0353000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+		};
+
+		usb_per5@a03e0000 {
+			phys = <&ab8500_usb>;
+			phy-names = "usb";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ab8505.dtsi b/arch/arm/boot/dts/st/ste-ab8505.dtsi
new file mode 100644
index 000000000000..131c82508e82
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ab8505.dtsi
@@ -0,0 +1,329 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/clock/ste-ab8500.h>
+
+/ {
+	/* Essential housekeeping hardware monitors */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&gpadc 0x02>, /* Battery temperature */
+			      <&gpadc 0x08>, /* Main battery voltage */
+			      <&gpadc 0x09>, /* VBUS */
+			      <&gpadc 0x0b>, /* Charger current */
+			      <&gpadc 0x0c>, /* Backup battery voltage */
+			      <&gpadc 0x0d>; /* Die temperature */
+	};
+
+	soc {
+		prcmu@80157000 {
+			ab8505 {
+				compatible = "stericsson,ab8505";
+				interrupt-parent = <&intc>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ab8500_clock: clock-controller {
+					compatible = "stericsson,ab8500-clk";
+					#clock-cells = <1>;
+				};
+
+				ab8505_gpio: gpio {
+					compatible = "stericsson,ab8505-gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				rtc {
+					compatible = "stericsson,ab8500-rtc";
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "60S", "ALARM";
+				};
+
+				gpadc: adc {
+					compatible = "stericsson,ab8500-gpadc";
+					interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "SW_CONV_END";
+					vddadc-supply = <&ab8500_ldo_adc_reg>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#io-channel-cells = <1>;
+
+					/* GPADC channels */
+					bat_ctrl: channel@1 {
+						reg = <0x01>;
+					};
+					btemp_ball: channel@2 {
+						reg = <0x02>;
+					};
+					acc_detect1: channel@4 {
+						reg = <0x04>;
+					};
+					acc_detect2: channel@5 {
+						reg = <0x05>;
+					};
+					adc_aux1: channel@6 {
+						reg = <0x06>;
+					};
+					adc_aux2: channel@7 {
+						reg = <0x07>;
+					};
+					main_batt_v: channel@8 {
+						reg = <0x08>;
+					};
+					vbus_v: channel@9 {
+						reg = <0x09>;
+					};
+					charger_c: channel@b {
+						reg = <0x0b>;
+					};
+					bk_bat_v: channel@c {
+						reg = <0x0c>;
+					};
+					die_temp: channel@d {
+						reg = <0x0d>;
+					};
+					usb_id: channel@e {
+						reg = <0x0e>;
+					};
+				};
+
+				thermal {
+					compatible = "stericsson,abx500-temp";
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ABX500_TEMP_WARM";
+				};
+
+				ab8500_fg {
+					compatible = "stericsson,ab8500-fg";
+					interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+						     <8 IRQ_TYPE_LEVEL_HIGH>,
+						     <28 IRQ_TYPE_LEVEL_HIGH>,
+						     <27 IRQ_TYPE_LEVEL_HIGH>,
+						     <26 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "NCONV_ACCU",
+							  "BATT_OVV",
+							  "LOW_BAT_F",
+							  "CC_INT_CALIB",
+							  "CCEOC";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x08>;
+					io-channel-names = "main_bat_v";
+				};
+
+				ab8500_btemp {
+					compatible = "stericsson,ab8500-btemp";
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH>,
+						     <80 IRQ_TYPE_LEVEL_HIGH>,
+						     <83 IRQ_TYPE_LEVEL_HIGH>,
+						     <81 IRQ_TYPE_LEVEL_HIGH>,
+						     <82 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "BAT_CTRL_INDB",
+							  "BTEMP_LOW",
+							  "BTEMP_HIGH",
+							  "BTEMP_LOW_MEDIUM",
+							  "BTEMP_MEDIUM_HIGH";
+					monitored-battery = <&battery>;
+					io-channels = <&gpadc 0x02>,
+						      <&gpadc 0x01>;
+					io-channel-names = "btemp_ball",
+							  "bat_ctrl";
+				};
+
+				ab8500_charger {
+					compatible = "stericsson,ab8500-charger";
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
+						     <11 IRQ_TYPE_LEVEL_HIGH>,
+						     <0 IRQ_TYPE_LEVEL_HIGH>,
+						     <107 IRQ_TYPE_LEVEL_HIGH>,
+						     <106 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <105 IRQ_TYPE_LEVEL_HIGH>,
+						     <104 IRQ_TYPE_LEVEL_HIGH>,
+						     <89 IRQ_TYPE_LEVEL_HIGH>,
+						     <22 IRQ_TYPE_LEVEL_HIGH>,
+						     <21 IRQ_TYPE_LEVEL_HIGH>,
+						     <16 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "MAIN_CH_UNPLUG_DET",
+							  "MAIN_CHARGE_PLUG_DET",
+							  "MAIN_EXT_CH_NOT_OK",
+							  "MAIN_CH_TH_PROT_R",
+							  "MAIN_CH_TH_PROT_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_CH_TH_PROT_R",
+							  "USB_CH_TH_PROT_F",
+							  "USB_CHARGER_NOT_OKR",
+							  "VBUS_OVV",
+							  "CH_WD_EXP",
+							  "VBUS_CH_DROP_END";
+					monitored-battery = <&battery>;
+					vddadc-supply = <&ab8500_ldo_adc_reg>;
+					io-channels = <&gpadc 0x09>,
+						      <&gpadc 0x0b>;
+					io-channel-names = "vbus_v",
+							  "usb_charger_c";
+				};
+
+				ab8500_chargalg {
+					compatible = "stericsson,ab8500-chargalg";
+					monitored-battery = <&battery>;
+				};
+
+				ab8500_usb: phy {
+					compatible = "stericsson,ab8500-usb";
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ID_WAKEUP_R",
+							  "ID_WAKEUP_F",
+							  "VBUS_DET_F",
+							  "VBUS_DET_R",
+							  "USB_LINK_STATUS",
+							  "USB_ADP_PROBE_PLUG",
+							  "USB_ADP_PROBE_UNPLUG";
+					vddulpivio18-supply = <&ab8500_ldo_intcore_reg>;
+					v-ape-supply = <&db8500_vape_reg>;
+					musb_1v8-supply = <&db8500_vsmps2_reg>;
+					clocks = <&prcmu_clk PRCMU_SYSCLK>;
+					clock-names = "sysclk";
+					#phy-cells = <0>;
+				};
+
+				key {
+					compatible = "stericsson,ab8500-poweron-key";
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
+				};
+
+				ab8500-sysctrl {
+					compatible = "stericsson,ab8500-sysctrl";
+				};
+
+				pwm@1 {
+					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
+					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
+					clock-names = "intclk";
+					#pwm-cells = <1>;
+				};
+
+				codec: codec {
+					compatible = "stericsson,ab8500-codec";
+
+					V-AUD-supply = <&ab8500_ldo_audio_reg>;
+					V-AMIC1-supply = <&ab8500_ldo_anamic1_reg>;
+					V-AMIC2-supply = <&ab8500_ldo_anamic2_reg>;
+
+					clocks = <&ab8500_clock AB8500_SYSCLK_AUDIO>;
+					clock-names = "audioclk";
+
+					stericsson,earpeice-cmv = <950>; /* Units in mV. */
+				};
+
+				regulator {
+					compatible = "stericsson,ab8505-regulator";
+
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4_reg: ab8500_ldo_aux4 {
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5_reg: ab8500_ldo_aux5 {
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					ab8500_ldo_aux6_reg: ab8500_ldo_aux6 {
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					// supply for v-intcore12; VINTCORE12 LDO
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-min-microvolt = <1250000>;
+						regulator-max-microvolt = <1350000>;
+					};
+
+					// supply for gpadc; ADC LDO
+					ab8500_ldo_adc_reg: ab8500_ldo_adc {
+					};
+
+					// supply for ab8500-vaudio; VAUDIO LDO
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+					};
+
+					// supply for v-anamic1 VAMIC1 LDO
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+					};
+
+					// supply for v-amic2; VAMIC2 LDO; reuse constants for AMIC1
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+					};
+
+					// supply for v-aux8; VAUX8 LDO
+					ab8500_ldo_aux8_reg: ab8500_ldo_aux8 {
+					};
+
+					// supply for U8500 CSI/DSI; VANA LDO
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+					};
+				};
+			};
+		};
+
+		sound {
+			stericsson,audio-codec = <&codec>;
+			clocks = <&prcmu_clk PRCMU_SYSCLK>, <&ab8500_clock AB8500_SYSCLK_ULP>, <&ab8500_clock AB8500_SYSCLK_INT>;
+			clock-names = "sysclk", "ulpclk", "intclk";
+		};
+
+		mcde@a0350000 {
+			vana-supply = <&ab8500_ldo_ana_reg>;
+
+			dsi@a0351000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0352000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+			dsi@a0353000 {
+				vana-supply = <&ab8500_ldo_ana_reg>;
+			};
+		};
+
+		usb_per5@a03e0000 {
+			phys = <&ab8500_usb>;
+			phy-names = "usb";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db8500.dtsi b/arch/arm/boot/dts/st/ste-db8500.dtsi
new file mode 100644
index 000000000000..f1ff3f4835d7
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db8500.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <998400 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@6000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@6f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@7000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db8520.dtsi b/arch/arm/boot/dts/st/ste-db8520.dtsi
new file mode 100644
index 000000000000..e4e8d5fc1f8a
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db8520.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <1152000 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* Modem trace memory */
+		ram@6000000 {
+			reg = <0x06000000 0x00f00000>;
+			no-map;
+		};
+
+		/* Modem shared memory */
+		ram@6f00000 {
+			reg = <0x06f00000 0x00100000>;
+			no-map;
+		};
+
+		/* Modem private memory */
+		ram@7000000 {
+			reg = <0x07000000 0x01000000>;
+			no-map;
+		};
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-db9500.dtsi b/arch/arm/boot/dts/st/ste-db9500.dtsi
new file mode 100644
index 000000000000..4273d36e881d
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-db9500.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "ste-dbx5x0.dtsi"
+
+/ {
+	cpus {
+		cpu@300 {
+			operating-points = <998400 0
+					    798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * Initial Secure Software ISSW memory
+		 *
+		 * This is probably only used if the kernel tries
+		 * to actually call into trustzone to run secure
+		 * applications, which the mainline kernel probably
+		 * will not do on this old chipset. But you can never
+		 * be too careful, so reserve this memory anyway.
+		 */
+		ram@17f00000 {
+			reg = <0x17f00000 0x00100000>;
+			no-map;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
new file mode 100644
index 000000000000..31a86606beda
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-dbx5x0-pinctrl.dtsi
@@ -0,0 +1,650 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Linaro Ltd.
+ */
+
+#include "ste-nomadik-pinctrl.dtsi"
+
+&pinctrl {
+	/* Settings for all UART default and sleep states */
+	uart0 {
+		u0_a_1_default: u0_a_1_default {
+			default_mux {
+				function = "u0";
+				groups = "u0_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u0_a_1_sleep: u0_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO1_AJ3"; /* RTS */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins = "GPIO3_AH3"; /* TXD */
+				ste,config = <&slpm_out_wkup_pdis>;
+			};
+		};
+	};
+
+	uart1 {
+		u1rxtx_a_1_default: u1rxtx_a_1_default {
+			default_mux {
+				function = "u1";
+				groups = "u1rxtx_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO4_AH6"; /* RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO5_AG6"; /* TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u1rxtx_a_1_sleep: u1rxtx_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO4_AH6"; /* RXD */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO5_AG6"; /* TXD */
+				ste,config = <&slpm_out_wkup_pdis>;
+			};
+		};
+
+		u1ctsrts_a_1_default: u1ctsrts_a_1_default {
+			default_mux {
+				function = "u1";
+				groups = "u1ctsrts_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO6_AF6"; /* CTS */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO7_AG5"; /* RTS */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u1ctsrts_a_1_sleep: u1ctsrts_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO6_AF6"; /* CTS */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO7_AG5"; /* RTS */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+		};
+	};
+
+	uart2 {
+		u2rxtx_c_1_default: u2rxtx_c_1_default {
+			default_mux {
+				function = "u2";
+				groups = "u2rxtx_c_1";
+			};
+			default_cfg1 {
+				pins = "GPIO29_W2"; /* RXD */
+				ste,config = <&in_pu>;
+			};
+			default_cfg2 {
+				pins = "GPIO30_W3"; /* TXD */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		u2rxtx_c_1_sleep: u2rxtx_c_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO29_W2"; /* RXD */
+				ste,config = <&in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO30_W3"; /* TXD */
+				ste,config = <&out_wkup_pdis>;
+			};
+		};
+	};
+
+	/* Settings for all I2C default and sleep states */
+	i2c0 {
+		i2c0_a_1_default: i2c0_a_1_default {
+			default_mux {
+				function = "i2c0";
+				groups = "i2c0_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c0_a_1_sleep: i2c0_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO147_C15", "GPIO148_B16"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c1 {
+		i2c1_b_2_default: i2c1_b_2_default {
+			default_mux {
+				function = "i2c1";
+				groups = "i2c1_b_2";
+			};
+			default_cfg1 {
+				pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c1_b_2_sleep: i2c1_b_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO16_AD3", "GPIO17_AD4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c2 {
+		i2c2_b_1_default: i2c2_b_1_default {
+			default_mux {
+				function = "i2c2";
+				groups = "i2c2_b_1";
+			};
+			default_cfg1 {
+				pins = "GPIO8_AD5", "GPIO9_AE4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c2_b_1_sleep: i2c2_b_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO8_AD5", "GPIO9_AE4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+
+		i2c2_b_2_default: i2c2_b_2_default {
+			default_mux {
+				function = "i2c2";
+				groups = "i2c2_b_2";
+			};
+			default_cfg1 {
+				pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c2_b_2_sleep: i2c2_b_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO10_AF5", "GPIO11_AG4"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	i2c3 {
+		i2c3_c_2_default: i2c3_c_2_default {
+			default_mux {
+				function = "i2c3";
+				groups = "i2c3_c_2";
+			};
+			default_cfg1 {
+				pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c3_c_2_sleep: i2c3_c_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO229_AG7", "GPIO230_AF7"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/*
+	 * Activating I2C4 will conflict with UART1 about the same pins so do not
+	 * enable I2C4 and UART1 at the same time.
+	 */
+	i2c4 {
+		i2c4_b_1_default: i2c4_b_1_default {
+			default_mux {
+				function = "i2c4";
+				groups = "i2c4_b_1";
+			};
+			default_cfg1 {
+				pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+				ste,config = <&in_nopull>;
+			};
+		};
+
+		i2c4_b_1_sleep: i2c4_b_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO4_AH6", "GPIO5_AG6"; /* SDA/SCL */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/* Settings for all MMC/SD/SDIO default and sleep states */
+	sdi0 {
+		/* This is the external SD card slot, 4 bits wide */
+		mc0_a_1_default: mc0_a_1_default {
+			default_mux {
+				function = "mc0";
+				groups = "mc0_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO18_AC2", /* CMDDIR */
+				"GPIO19_AC1", /* DAT0DIR */
+				"GPIO20_AB4"; /* DAT2DIR */
+				ste,config = <&out_hi>;
+			};
+			default_cfg2 {
+				pins = "GPIO22_AA3"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg4 {
+				pins =
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc0_a_1_sleep: mc0_a_1_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO18_AC2", /* CMDDIR */
+				"GPIO19_AC1", /* DAT0DIR */
+				"GPIO20_AB4"; /* DAT2DIR */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO22_AA3", /* FBCLK */
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+		};
+
+		mc0_a_2_default: mc0_a_2_default {
+			default_mux {
+				function = "mc0";
+				groups = "mc0_a_2";
+			};
+			default_cfg1 {
+				pins = "GPIO22_AA3"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg2 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc0_a_2_sleep: mc0_a_2_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO22_AA3", /* FBCLK */
+				"GPIO24_AB2", /* CMD */
+				"GPIO25_Y4", /* DAT0 */
+				"GPIO26_Y2", /* DAT1 */
+				"GPIO27_AA2", /* DAT2 */
+				"GPIO28_AA1"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO23_AA4"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi1 {
+		/* This is the WLAN SDIO 4 bits wide */
+		mc1_a_1_default: mc1_a_1_default {
+			default_mux {
+				function = "mc1";
+				groups = "mc1_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO209_AG15"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc1_a_1_sleep: mc1_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO209_AG15", /* FBCLK */
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+
+		mc1_a_2_default: mc1_a_2_default {
+			default_mux {
+				function = "mc1";
+				groups = "mc1_a_2";
+			};
+			default_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc1_a_2_sleep: mc1_a_2_sleep {
+			sleep_cfg1 {
+				pins = "GPIO208_AH16"; /* CLK */
+				ste,config = <&slpm_out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO210_AJ15", /* CMD */
+				"GPIO211_AG14", /* DAT0 */
+				"GPIO212_AF13", /* DAT1 */
+				"GPIO213_AG13", /* DAT2 */
+				"GPIO214_AH15"; /* DAT3 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi2 {
+		/* This is the eMMC 8 bits wide, usually PoP eMMC */
+		mc2_a_1_default: mc2_a_1_default {
+			default_mux {
+				function = "mc2";
+				groups = "mc2_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO129_B4", /* CMD */
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc2_a_1_sleep: mc2_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO128_A5"; /* CLK */
+				ste,config = <&out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO130_C8", /* FBCLK */
+				"GPIO129_B4"; /* CMD */
+				ste,config = <&in_wkup_pdis_en>;
+			};
+			sleep_cfg3 {
+				pins =
+				"GPIO131_A12", /* DAT0 */
+				"GPIO132_C10", /* DAT1 */
+				"GPIO133_B10", /* DAT2 */
+				"GPIO134_B9", /* DAT3 */
+				"GPIO135_A9", /* DAT4 */
+				"GPIO136_C7", /* DAT5 */
+				"GPIO137_A7", /* DAT6 */
+				"GPIO138_C5"; /* DAT7 */
+				ste,config = <&in_wkup_pdis>;
+			};
+		};
+	};
+
+	sdi4 {
+		/* This is the eMMC 8 bits wide, usually PCB-mounted eMMC */
+		mc4_a_1_default: mc4_a_1_default {
+			default_mux {
+				function = "mc4";
+				groups = "mc4_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO203_AE23"; /* CLK */
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins = "GPIO202_AF25"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg3 {
+				pins =
+				"GPIO201_AF24", /* CMD */
+				"GPIO200_AH26", /* DAT0 */
+				"GPIO199_AH23", /* DAT1 */
+				"GPIO198_AG25", /* DAT2 */
+				"GPIO197_AH24", /* DAT3 */
+				"GPIO207_AJ23", /* DAT4 */
+				"GPIO206_AG24", /* DAT5 */
+				"GPIO205_AG23", /* DAT6 */
+				"GPIO204_AF23"; /* DAT7 */
+				ste,config = <&in_pu>;
+			};
+		};
+
+		mc4_a_1_sleep: mc4_a_1_sleep {
+			sleep_cfg1 {
+				pins = "GPIO203_AE23"; /* CLK */
+				ste,config = <&out_lo_wkup_pdis>;
+			};
+			sleep_cfg2 {
+				pins =
+				"GPIO202_AF25", /* FBCLK */
+				"GPIO201_AF24", /* CMD */
+				"GPIO200_AH26", /* DAT0 */
+				"GPIO199_AH23", /* DAT1 */
+				"GPIO198_AG25", /* DAT2 */
+				"GPIO197_AH24", /* DAT3 */
+				"GPIO207_AJ23", /* DAT4 */
+				"GPIO206_AG24", /* DAT5 */
+				"GPIO205_AG23", /* DAT6 */
+				"GPIO204_AF23"; /* DAT7 */
+				ste,config = <&slpm_in_wkup_pdis>;
+			};
+		};
+	};
+
+	/*
+	 * Multi-rate serial ports (MSPs) - MSP3 output is internal and
+	 * cannot be muxed onto any pins.
+	 */
+	msp0 {
+		msp0txrxtfstck_a_1_default: msp0txrxtfstck_a_1_default {
+			default_msp0_mux {
+				function = "msp0";
+				groups = "msp0txrx_a_1", "msp0tfstck_a_1";
+			};
+			default_msp0_cfg {
+				pins =
+				"GPIO12_AC4", /* TXD */
+				"GPIO15_AC3", /* RXD */
+				"GPIO13_AF3", /* TFS */
+				"GPIO14_AE3"; /* TCK */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	msp1 {
+		msp1txrx_a_1_default: msp1txrx_a_1_default {
+			default_mux {
+				function = "msp1";
+				groups = "msp1txrx_a_1", "msp1_a_1";
+			};
+			default_cfg1 {
+				pins = "GPIO33_AF2";
+				ste,config = <&out_lo>;
+			};
+			default_cfg2 {
+				pins =
+				"GPIO34_AE1",
+				"GPIO35_AE2",
+				"GPIO36_AG2";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	msp2 {
+		msp2_a_1_default: msp2_a_1_default {
+			/* MSP2 usually used for HDMI audio */
+			default_mux {
+				function = "msp2";
+				groups = "msp2_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO193_AH27", /* TXD */
+				"GPIO194_AF27", /* TCK */
+				"GPIO195_AG28"; /* TFS */
+				ste,config = <&in_pd>;
+			};
+			default_cfg2 {
+				pins = "GPIO196_AG26"; /* RXD */
+				ste,config = <&out_lo>;
+			};
+		};
+	};
+
+	musb {
+		usb_a_1_default: usb_a_1_default {
+			default_mux {
+				function = "usb";
+				groups = "usb_a_1";
+			};
+			default_cfg1 {
+				pins =
+				"GPIO256_AF28", /* NXT */
+				"GPIO258_AD29", /* XCLK */
+				"GPIO259_AC29", /* DIR */
+				"GPIO260_AD28", /* DAT7 */
+				"GPIO261_AD26", /* DAT6 */
+				"GPIO262_AE26", /* DAT5 */
+				"GPIO263_AG29", /* DAT4 */
+				"GPIO264_AE27", /* DAT3 */
+				"GPIO265_AD27", /* DAT2 */
+				"GPIO266_AC28", /* DAT1 */
+				"GPIO267_AC27"; /* DAT0 */
+				ste,config = <&in_nopull>;
+			};
+			default_cfg2 {
+				pins = "GPIO257_AE29"; /* STP */
+				ste,config = <&out_hi>;
+			};
+		};
+
+		usb_a_1_sleep: usb_a_1_sleep {
+			sleep_cfg1 {
+				pins =
+				"GPIO256_AF28", /* NXT */
+				"GPIO258_AD29", /* XCLK */
+				"GPIO259_AC29"; /* DIR */
+				ste,config = <&slpm_wkup_pdis_en>;
+			};
+			sleep_cfg2 {
+				pins = "GPIO257_AE29"; /* STP */
+				ste,config = <&slpm_out_hi_wkup_pdis>;
+			};
+			sleep_cfg3 {
+				pins =
+				"GPIO260_AD28", /* DAT7 */
+				"GPIO261_AD26", /* DAT6 */
+				"GPIO262_AE26", /* DAT5 */
+				"GPIO263_AG29", /* DAT4 */
+				"GPIO264_AE27", /* DAT3 */
+				"GPIO265_AD27", /* DAT2 */
+				"GPIO266_AC28", /* DAT1 */
+				"GPIO267_AC27"; /* DAT0 */
+				ste,config = <&slpm_in_wkup_pdis_en>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
new file mode 100644
index 000000000000..d5d88771ef97
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
@@ -0,0 +1,1238 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Linaro Ltd
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/ste-db8500-clkout.h>
+#include <dt-bindings/reset/stericsson,db8500-prcc-reset.h>
+#include <dt-bindings/mfd/dbx500-prcmu.h>
+#include <dt-bindings/arm/ux500_pm_domains.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/* This stablilizes the device enumeration */
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+	};
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "ste,dbx500-smp";
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+				core1 {
+					cpu = <&CPU1>;
+				};
+			};
+		};
+		CPU0: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x300>;
+			clocks = <&prcmu_clk PRCMU_ARMSS>;
+			clock-names = "cpu";
+			clock-latency = <20000>;
+			#cooling-cells = <2>;
+		};
+		CPU1: cpu@301 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0x301>;
+		};
+	};
+
+	thermal-zones {
+		/*
+		 * Thermal zone for the SoC, using the thermal sensor in the
+		 * PRCMU for temperature and the cpufreq driver for passive
+		 * cooling.
+		 */
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			/*
+			 * This sensor fires interrupts to update the thermal
+			 * zone, so no polling is needed.
+			 */
+			polling-delay = <0>;
+
+			thermal-sensors = <&thermal>;
+
+			trips {
+				cpu_alert: cpu-alert {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu-crit {
+					temperature = <85000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				trip = <&cpu_alert>;
+				cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				contribution = <100>;
+			};
+		};
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "stericsson,db8500", "simple-bus";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		/*
+		 * 640KB ESRAM (embedded static random access memory), divided
+		 * into 5 banks of 128 KB each. This is a fast memory usually
+		 * used by different accelerators. We group these according to
+		 * their power domains: ESRAM0 (always on) ESRAM 1+2 and
+		 * ESRAM 3+4.
+		 */
+		sram@40000000 {
+			/* The first (always on) ESRAM 0, 128 KB */
+			compatible = "mmio-sram";
+			reg = <0x40000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40000000 0x20000>;
+
+			sram@0 {
+				compatible = "stericsson,u8500-esram";
+				reg = <0x0 0x10000>;
+				pool;
+			};
+			lcpa: sram@10000 {
+				/*
+				 * This eSRAM is used by the DMA40 DMA controller
+				 * for Logical Channel Paramers (LCP), the address
+				 * where these parameters are stored is called "LCPA".
+				 * This is addressed directly by the driver so no
+				 * pool is used.
+				 */
+				compatible = "stericsson,u8500-esram";
+				label = "DMA40-LCPA";
+				reg = <0x10000 0x800>;
+			};
+			sram@10800 {
+				compatible = "stericsson,u8500-esram";
+				reg = <0x10800 0xf800>;
+				pool;
+			};
+		};
+		sram@40020000 {
+			/* ESRAM 1+2, 256 KB */
+			compatible = "mmio-sram";
+			reg = <0x40020000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40020000 0x40000>;
+		};
+		sram@40060000 {
+			/* ESRAM 3+4, 256 KB */
+			compatible = "mmio-sram";
+			reg = <0x40060000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40060000 0x40000>;
+
+			lcla: sram@20000 {
+				/*
+				 * This eSRAM is used by the DMA40 DMA controller
+				 * for Logical Channel Logical Addresses (LCLA), the address
+				 * where these parameters are stored is called "LCLA".
+				 * This is addressed directly by the driver so no
+				 * pool is used.
+				 */
+				compatible = "stericsson,u8500-esram";
+				label = "DMA40-LCLA";
+				reg = <0x20000 0x2000>;
+			};
+		};
+
+		ptm@801ae000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x801ae000 0x1000>;
+
+			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "apb_pclk", "atclk";
+			cpu = <&CPU0>;
+			out-ports {
+				port {
+					ptm0_out_port: endpoint {
+						remote-endpoint = <&funnel_in_port0>;
+					};
+				};
+			};
+		};
+
+		ptm@801af000 {
+			compatible = "arm,coresight-etm3x", "arm,primecell";
+			reg = <0x801af000 0x1000>;
+
+			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "apb_pclk", "atclk";
+			cpu = <&CPU1>;
+			out-ports {
+				port {
+					ptm1_out_port: endpoint {
+						remote-endpoint = <&funnel_in_port1>;
+					};
+				};
+			};
+		};
+
+		funnel@801a6000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0x801a6000 0x1000>;
+
+			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "apb_pclk", "atclk";
+			out-ports {
+				port {
+					funnel_out_port: endpoint {
+						remote-endpoint =
+							<&replicator_in_port0>;
+					};
+				};
+			};
+
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					funnel_in_port0: endpoint {
+						remote-endpoint = <&ptm0_out_port>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					funnel_in_port1: endpoint {
+						remote-endpoint = <&ptm1_out_port>;
+					};
+				};
+			};
+		};
+
+		replicator {
+			compatible = "arm,coresight-static-replicator";
+			clocks = <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "atclk";
+
+			out-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					replicator_out_port0: endpoint {
+						remote-endpoint = <&tpiu_in_port>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out_port1: endpoint {
+						remote-endpoint = <&etb_in_port>;
+					};
+				};
+			};
+
+			in-ports {
+				port {
+					replicator_in_port0: endpoint {
+						remote-endpoint = <&funnel_out_port>;
+					};
+				};
+			};
+		};
+
+		tpiu@80190000 {
+			compatible = "arm,coresight-tpiu", "arm,primecell";
+			reg = <0x80190000 0x1000>;
+
+			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "apb_pclk", "atclk";
+			in-ports {
+				port {
+					tpiu_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port0>;
+					};
+				};
+			};
+		};
+
+		etb@801a4000 {
+			compatible = "arm,coresight-etb10", "arm,primecell";
+			reg = <0x801a4000 0x1000>;
+
+			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
+			clock-names = "apb_pclk", "atclk";
+			in-ports {
+				port {
+					etb_in_port: endpoint {
+						remote-endpoint = <&replicator_out_port1>;
+					};
+				};
+			};
+		};
+
+		intc: interrupt-controller@a0411000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0xa0411000 0x1000>,
+			      <0xa0410100 0x100>;
+		};
+
+		scu@a0410000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0xa0410000 0x100>;
+		};
+
+		/*
+		 * The backup RAM is used for retention during sleep
+		 * and various things like spin tables
+		 */
+		backupram@80150000 {
+			compatible = "ste,dbx500-backupram";
+			reg = <0x80150000 0x2000>;
+		};
+
+		L2: cache-controller {
+			compatible = "arm,pl310-cache";
+			reg = <0xa0412000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		pmu {
+			compatible = "arm,cortex-a9-pmu";
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pm_domains: pm_domains0 {
+			compatible = "stericsson,ux500-pm-domains";
+			#power-domain-cells = <1>;
+		};
+
+		clocks {
+			compatible = "stericsson,u8500-clks";
+			/*
+			 * Registers for the CLKRST block on peripheral
+			 * groups 1, 2, 3, 5, 6,
+			 */
+			reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>,
+			    <0x8000f000 0x1000>, <0xa03ff000 0x1000>,
+			    <0xa03cf000 0x1000>;
+
+			prcmu_clk: prcmu-clock {
+				#clock-cells = <1>;
+			};
+
+			prcc_pclk: prcc-periph-clock {
+				#clock-cells = <2>;
+			};
+
+			prcc_kclk: prcc-kernel-clock {
+				#clock-cells = <2>;
+			};
+
+			prcc_reset: prcc-reset-controller {
+				#reset-cells = <2>;
+			};
+
+			rtc_clk: rtc32k-clock {
+				#clock-cells = <0>;
+			};
+
+			smp_twd_clk: smp-twd-clock {
+				#clock-cells = <0>;
+			};
+
+			clkout_clk: clkout-clock {
+				/* Cell 1 id, cell 2 source, cell 3 div */
+				#clock-cells = <3>;
+			};
+		};
+
+		mtu@a03c6000 {
+			/* Nomadik System Timer */
+			compatible = "st,nomadik-mtu";
+			reg = <0xa03c6000 0x1000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>;
+			clock-names = "timclk", "apb_pclk";
+		};
+
+		timer@a0410600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0xa0410600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
+
+			clocks = <&smp_twd_clk>;
+		};
+
+		watchdog@a0410620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0xa0410620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&smp_twd_clk>;
+		};
+
+		rtc@80154000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0x80154000 0x1000>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&rtc_clk>;
+			clock-names = "apb_pclk";
+		};
+
+		gpio0: gpio@8012e000 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8012e000 0x80>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <0>;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			clocks = <&prcc_pclk 1 9>;
+		};
+
+		gpio1: gpio@8012e080 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8012e080 0x80>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <1>;
+			gpio-ranges = <&pinctrl 0 32 5>;
+			clocks = <&prcc_pclk 1 9>;
+		};
+
+		gpio2: gpio@8000e000 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8000e000 0x80>;
+			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <2>;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			clocks = <&prcc_pclk 3 8>;
+		};
+
+		gpio3: gpio@8000e080 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8000e080 0x80>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <3>;
+			gpio-ranges = <&pinctrl 0 96 2>;
+			clocks = <&prcc_pclk 3 8>;
+		};
+
+		gpio4: gpio@8000e100 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8000e100 0x80>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <4>;
+			gpio-ranges = <&pinctrl 0 128 32>;
+			clocks = <&prcc_pclk 3 8>;
+		};
+
+		gpio5: gpio@8000e180 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8000e180 0x80>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <5>;
+			gpio-ranges = <&pinctrl 0 160 12>;
+			clocks = <&prcc_pclk 3 8>;
+		};
+
+		gpio6: gpio@8011e000 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8011e000 0x80>;
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <6>;
+			gpio-ranges = <&pinctrl 0 192 32>;
+			clocks = <&prcc_pclk 2 11>;
+		};
+
+		gpio7: gpio@8011e080 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0x8011e080 0x80>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <7>;
+			gpio-ranges = <&pinctrl 0 224 7>;
+			clocks = <&prcc_pclk 2 11>;
+		};
+
+		gpio8: gpio@a03fe000 {
+			compatible = "stericsson,db8500-gpio",
+				"st,nomadik-gpio";
+			reg =  <0xa03fe000 0x80>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			st,supports-sleepmode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-bank = <8>;
+			gpio-ranges = <&pinctrl 0 256 12>;
+			clocks = <&prcc_pclk 5 1>;
+		};
+
+		pinctrl: pinctrl {
+			compatible = "stericsson,db8500-pinctrl";
+			nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>,
+						<&gpio4>, <&gpio5>, <&gpio6>, <&gpio7>,
+						<&gpio8>;
+			prcm = <&prcmu>;
+		};
+
+		usb_per5@a03e0000 {
+			compatible = "stericsson,db8500-musb";
+			reg = <0xa03e0000 0x10000>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+
+			dr_mode = "otg";
+
+			dmas = <&dma 38 0 0x2>, /* Logical - DevToMem */
+			       <&dma 38 0 0x0>, /* Logical - MemToDev */
+			       <&dma 37 0 0x2>, /* Logical - DevToMem */
+			       <&dma 37 0 0x0>, /* Logical - MemToDev */
+			       <&dma 36 0 0x2>, /* Logical - DevToMem */
+			       <&dma 36 0 0x0>, /* Logical - MemToDev */
+			       <&dma 19 0 0x2>, /* Logical - DevToMem */
+			       <&dma 19 0 0x0>, /* Logical - MemToDev */
+			       <&dma 18 0 0x2>, /* Logical - DevToMem */
+			       <&dma 18 0 0x0>, /* Logical - MemToDev */
+			       <&dma 17 0 0x2>, /* Logical - DevToMem */
+			       <&dma 17 0 0x0>, /* Logical - MemToDev */
+			       <&dma 16 0 0x2>, /* Logical - DevToMem */
+			       <&dma 16 0 0x0>, /* Logical - MemToDev */
+			       <&dma 39 0 0x2>, /* Logical - DevToMem */
+			       <&dma 39 0 0x0>; /* Logical - MemToDev */
+
+			dma-names = "iep_1_9",  "oep_1_9",
+				    "iep_2_10", "oep_2_10",
+				    "iep_3_11", "oep_3_11",
+				    "iep_4_12", "oep_4_12",
+				    "iep_5_13", "oep_5_13",
+				    "iep_6_14", "oep_6_14",
+				    "iep_7_15", "oep_7_15",
+				    "iep_8",    "oep_8";
+
+			clocks = <&prcc_pclk 5 0>;
+		};
+
+		dma: dma-controller@801C0000 {
+			compatible = "stericsson,db8500-dma40", "stericsson,dma40";
+			reg = <0x801C0000 0x1000>;
+			reg-names = "base";
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			sram = <&lcpa>, <&lcla>;
+
+			#dma-cells = <3>;
+			memcpy-channels = <56 57 58 59 60>;
+
+			clocks = <&prcmu_clk PRCMU_DMACLK>;
+		};
+
+		prcmu: prcmu@80157000 {
+			compatible = "stericsson,db8500-prcmu", "syscon";
+			reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>;
+			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ranges;
+
+			prcmu-timer-4@80157450 {
+				compatible = "stericsson,db8500-prcmu-timer-4";
+				reg = <0x80157450 0xC>;
+			};
+
+			thermal: thermal@801573c0 {
+				compatible = "stericsson,db8500-thermal";
+				reg = <0x801573c0 0x40>;
+				interrupt-parent = <&prcmu>;
+				interrupts = <21 IRQ_TYPE_LEVEL_HIGH>,
+					     <22 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH";
+				#thermal-sensor-cells = <0>;
+			};
+
+			db8500-prcmu-regulators {
+				compatible = "stericsson,db8500-prcmu-regulator";
+
+				// DB8500_REGULATOR_VAPE
+				db8500_vape_reg: db8500_vape {
+					regulator-always-on;
+				};
+
+				// DB8500_REGULATOR_VARM
+				db8500_varm_reg: db8500_varm {
+				};
+
+				// DB8500_REGULATOR_VMODEM
+				db8500_vmodem_reg: db8500_vmodem {
+				};
+
+				// DB8500_REGULATOR_VPLL
+				db8500_vpll_reg: db8500_vpll {
+				};
+
+				// DB8500_REGULATOR_VSMPS1
+				db8500_vsmps1_reg: db8500_vsmps1 {
+				};
+
+				// DB8500_REGULATOR_VSMPS2
+				db8500_vsmps2_reg: db8500_vsmps2 {
+				};
+
+				// DB8500_REGULATOR_VSMPS3
+				db8500_vsmps3_reg: db8500_vsmps3 {
+				};
+
+				// DB8500_REGULATOR_VRF1
+				db8500_vrf1_reg: db8500_vrf1 {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SVAMMDSP
+				db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SVAMMDSPRET
+				db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SVAPIPE
+				db8500_sva_pipe_reg: db8500_sva_pipe {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SIAMMDSP
+				db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SIAMMDSPRET
+				db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SIAPIPE
+				db8500_sia_pipe_reg: db8500_sia_pipe {
+				};
+
+				// DB8500_REGULATOR_SWITCH_SGA
+				db8500_sga_reg: db8500_sga {
+					vin-supply = <&db8500_vape_reg>;
+				};
+
+				// DB8500_REGULATOR_SWITCH_B2R2_MCDE
+				db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
+					vin-supply = <&db8500_vape_reg>;
+				};
+
+				// DB8500_REGULATOR_SWITCH_ESRAM12
+				db8500_esram12_reg: db8500_esram12 {
+				};
+
+				// DB8500_REGULATOR_SWITCH_ESRAM12RET
+				db8500_esram12_ret_reg: db8500_esram12_ret {
+				};
+
+				// DB8500_REGULATOR_SWITCH_ESRAM34
+				db8500_esram34_reg: db8500_esram34 {
+				};
+
+				// DB8500_REGULATOR_SWITCH_ESRAM34RET
+				db8500_esram34_ret_reg: db8500_esram34_ret {
+				};
+			};
+		};
+
+		i2c0: i2c@80004000 {
+			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
+			reg = <0x80004000 0x1000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clock-frequency = <400000>;
+			clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
+			clock-names = "i2cclk", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_I2C0>;
+
+			status = "disabled";
+		};
+
+		i2c1: i2c@80122000 {
+			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
+			reg = <0x80122000 0x1000>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clock-frequency = <400000>;
+
+			clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
+			clock-names = "i2cclk", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C1>;
+
+			status = "disabled";
+		};
+
+		i2c2: i2c@80128000 {
+			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
+			reg = <0x80128000 0x1000>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clock-frequency = <400000>;
+
+			clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
+			clock-names = "i2cclk", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C2>;
+
+			status = "disabled";
+		};
+
+		i2c3: i2c@80110000 {
+			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
+			reg = <0x80110000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clock-frequency = <400000>;
+
+			clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
+			clock-names = "i2cclk", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_I2C3>;
+
+			status = "disabled";
+		};
+
+		i2c4: i2c@8012a000 {
+			compatible = "stericsson,db8500-i2c", "st,nomadik-i2c", "arm,primecell";
+			reg = <0x8012a000 0x1000>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clock-frequency = <400000>;
+
+			clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
+			clock-names = "i2cclk", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C4>;
+
+			status = "disabled";
+		};
+
+		ssp0: spi@80002000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x80002000 0x1000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */
+			       <&dma 8 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP0>;
+
+			status = "disabled";
+		};
+
+		ssp1: spi@80003000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x80003000 0x1000>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */
+			       <&dma 9 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP1>;
+
+			status = "disabled";
+		};
+
+		spi0: spi@8011a000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x8011a000 0x1000>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* Same clock wired to kernel and pclk */
+			clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */
+			       <&dma 0 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
+		};
+
+		spi1: spi@80112000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x80112000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* Same clock wired to kernel and pclk */
+			clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */
+			       <&dma 35 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
+		};
+
+		spi2: spi@80111000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x80111000 0x1000>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* Same clock wired to kernel and pclk */
+			clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */
+			       <&dma 33 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+
+			status = "disabled";
+		};
+
+		spi3: spi@80129000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x80129000 0x1000>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* Same clock wired to kernel and pclk */
+			clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>;
+			clock-names = "sspclk", "apb_pclk";
+			dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */
+			       <&dma 40 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SPI3>;
+
+			status = "disabled";
+		};
+
+		serial0: serial@80120000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80120000 0x1000>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */
+			       <&dma 13 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
+			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART0>;
+
+			status = "disabled";
+		};
+
+		serial1: serial@80121000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80121000 0x1000>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 12 0 0x2>, /* Logical - DevToMem */
+			       <&dma 12 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
+			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART1>;
+
+			status = "disabled";
+		};
+
+		serial2: serial@80007000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x80007000 0x1000>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 11 0 0x2>, /* Logical - DevToMem */
+			       <&dma 11 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
+			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_UART2>;
+
+			status = "disabled";
+		};
+
+		mmc@80126000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80126000 0x1000>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 29 0 0x2>, /* Logical - DevToMem */
+			       <&dma 29 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SDI0>;
+
+			status = "disabled";
+		};
+
+		mmc@80118000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80118000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 32 0 0x2>, /* Logical - DevToMem */
+			       <&dma 32 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI1>;
+
+			status = "disabled";
+		};
+
+		mmc@80005000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80005000 0x1000>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 28 0 0x2>, /* Logical - DevToMem */
+			       <&dma 28 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI2>;
+
+			status = "disabled";
+		};
+
+		mmc@80119000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80119000 0x1000>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 41 0 0x2>, /* Logical - DevToMem */
+			       <&dma 41 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI3>;
+
+			status = "disabled";
+		};
+
+		mmc@80114000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80114000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 42 0 0x2>, /* Logical - DevToMem */
+			       <&dma 42 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI4>;
+
+			status = "disabled";
+		};
+
+		mmc@80008000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x80008000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+
+			dmas = <&dma 43 0 0x2>, /* Logical - DevToMem */
+			       <&dma 43 0 0x0>; /* Logical - MemToDev */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
+			clock-names = "sdi", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI5>;
+
+			status = "disabled";
+		};
+
+		sound {
+			compatible = "stericsson,snd-soc-mop500";
+			stericsson,cpu-dai = <&msp1 &msp3>;
+		};
+
+		msp0: msp@80123000 {
+			compatible = "stericsson,ux500-msp-i2s";
+			reg = <0x80123000 0x1000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			v-ape-supply = <&db8500_vape_reg>;
+
+			dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */
+			       <&dma 31 0 0x10>; /* Logical - MemToDev - HighPrio */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
+			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP0>;
+
+			status = "disabled";
+		};
+
+		msp1: msp@80124000 {
+			compatible = "stericsson,ux500-msp-i2s";
+			reg = <0x80124000 0x1000>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			v-ape-supply = <&db8500_vape_reg>;
+
+			/* This DMA channel only exist on DB8500 v1 */
+			dmas = <&dma 30 0 0x10>; /* Logical - MemToDev - HighPrio */
+			dma-names = "tx";
+
+			clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
+			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP1>;
+
+			status = "disabled";
+		};
+
+		// HDMI sound
+		msp2: msp@80117000 {
+			compatible = "stericsson,ux500-msp-i2s";
+			reg = <0x80117000 0x1000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			v-ape-supply = <&db8500_vape_reg>;
+
+			dmas = <&dma 14 0 0x12>, /* Logical  - DevToMem - HighPrio */
+			       <&dma 14 1 0x19>; /* Physical Chan 1 - MemToDev
+                                                    HighPrio - Fixed */
+			dma-names = "rx", "tx";
+
+			clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
+			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_MSP2>;
+
+			status = "disabled";
+		};
+
+		msp3: msp@80125000 {
+			compatible = "stericsson,ux500-msp-i2s";
+			reg = <0x80125000 0x1000>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			v-ape-supply = <&db8500_vape_reg>;
+
+			/* This DMA channel only exist on DB8500 v2 */
+			dmas = <&dma 30 0 0x12>; /* Logical - DevToMem - HighPrio */
+			dma-names = "rx";
+
+			clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
+			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP3>;
+
+			status = "disabled";
+		};
+
+		external-bus@50000000 {
+			compatible = "simple-bus";
+			reg = <0x50000000 0x4000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x50000000 0x4000000>;
+			status = "disabled";
+		};
+
+		gpu@a0300000 {
+			/*
+			 * This block is referred to as "Smart Graphics Adapter SGA500"
+			 * in documentation but is in practice a pretty straight-forward
+			 * MALI-400 GPU block.
+			 */
+			compatible = "stericsson,db8500-mali", "arm,mali-400";
+			reg = <0xa0300000 0x10000>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp0",
+					  "ppmmu0",
+					  "combined";
+			clocks = <&prcmu_clk PRCMU_ACLK>, <&prcmu_clk PRCMU_SGACLK>;
+			clock-names = "bus", "core";
+			mali-supply = <&db8500_sga_reg>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+		};
+
+		mcde@a0350000 {
+			compatible = "ste,mcde";
+			reg = <0xa0350000 0x1000>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			epod-supply = <&db8500_b2r2_mcde_reg>;
+			clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
+				 <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
+				 <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
+			clock-names = "mcde", "lcd", "hdmi";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			dsi0: dsi@a0351000 {
+				compatible = "ste,mcde-dsi";
+				reg = <0xa0351000 0x1000>;
+				clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
+				clock-names = "hs", "lp";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+			dsi1: dsi@a0352000 {
+				compatible = "ste,mcde-dsi";
+				reg = <0xa0352000 0x1000>;
+				clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
+				clock-names = "hs", "lp";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+			dsi2: dsi@a0353000 {
+				compatible = "ste,mcde-dsi";
+				reg = <0xa0353000 0x1000>;
+				/* This DSI port only has the Low Power / Energy Save clock */
+				clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
+				clock-names = "lp";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		cryp@a03cb000 {
+			compatible = "stericsson,ux500-cryp";
+			reg = <0xa03cb000 0x1000>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&prcc_pclk 6 1>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+		};
+
+		hash@a03c2000 {
+			compatible = "stericsson,ux500-hash";
+			reg = <0xa03c2000 0x1000>;
+			clocks = <&prcc_pclk 6 2>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-ab8500.dtsi b/arch/arm/boot/dts/st/ste-href-ab8500.dtsi
new file mode 100644
index 000000000000..e1de9d389a01
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-ab8500.dtsi
@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2014 Linaro Ltd.
+ */
+
+#include "ste-ab8500.dtsi"
+
+/ {
+	soc {
+		prcmu@80157000 {
+			ab8500 {
+				gpio {
+					/* Hog a few default settings */
+					pinctrl-names = "default";
+					pinctrl-0 = <&gpio2_default_mode>,
+						    <&gpio4_default_mode>,
+						    <&gpio10_default_mode>,
+						    <&gpio11_default_mode>,
+						    <&gpio12_default_mode>,
+						    <&gpio13_default_mode>,
+						    <&gpio16_default_mode>,
+						    <&gpio24_default_mode>,
+						    <&gpio25_default_mode>,
+						    <&gpio36_default_mode>,
+						    <&gpio37_default_mode>,
+						    <&gpio38_default_mode>,
+						    <&gpio39_default_mode>,
+						    <&gpio42_default_mode>,
+						    <&gpio26_default_mode>,
+						    <&gpio35_default_mode>,
+						    <&ycbcr_default_mode>,
+						    <&pwm_default_mode>,
+						    <&adi1_default_mode>,
+						    <&usbuicc_default_mode>,
+						    <&dmic_default_mode>,
+						    <&extcpena_default_mode>,
+						    <&modsclsda_default_mode>;
+
+					/*
+					 * Pins 2, 4, 10, 11, 12, 13, 16, 24, 25, 36, 37, 38, 39 and 42
+					 * are muxed in as GPIO, and configured as INPUT PULL DOWN
+					 */
+					gpio2 {
+						gpio2_default_mode: gpio2_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio2_a_1";
+							};
+							default_cfg {
+								pins = "GPIO2_T9";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio4 {
+						gpio4_default_mode: gpio4_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio4_a_1";
+							};
+							default_cfg {
+								pins = "GPIO4_W2";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio10 {
+						gpio10_default_mode: gpio10_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio10_d_1";
+							};
+							default_cfg {
+								pins = "GPIO10_U17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio11 {
+						gpio11_default_mode: gpio11_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio11_d_1";
+							};
+							default_cfg {
+								pins = "GPIO11_AA18";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio12 {
+						gpio12_default_mode: gpio12_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio12_d_1";
+							};
+							default_cfg {
+								pins = "GPIO12_U16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio13 {
+						gpio13_default_mode: gpio13_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio13_d_1";
+							};
+							default_cfg {
+								pins = "GPIO13_W17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio16 {
+						gpio16_default_mode: gpio16_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio16_a_1";
+							};
+							default_cfg {
+								pins = "GPIO16_F15";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio24 {
+						gpio24_default_mode: gpio24_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio24_a_1";
+							};
+							default_cfg {
+								pins = "GPIO24_T14";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio25 {
+						gpio25_default_mode: gpio25_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio25_a_1";
+							};
+							default_cfg {
+								pins = "GPIO25_R16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio36 {
+						gpio36_default_mode: gpio36_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio36_a_1";
+							};
+							default_cfg {
+								pins = "GPIO36_A17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio37 {
+						gpio37_default_mode: gpio37_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio37_a_1";
+							};
+							default_cfg {
+								pins = "GPIO37_E15";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio38 {
+						gpio38_default_mode: gpio38_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio38_a_1";
+							};
+							default_cfg {
+								pins = "GPIO38_C17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio39 {
+						gpio39_default_mode: gpio39_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio39_a_1";
+							};
+							default_cfg {
+								pins = "GPIO39_E16";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					gpio42 {
+						gpio42_default_mode: gpio42_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio42_a_1";
+							};
+							default_cfg {
+								pins = "GPIO42_U2";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/*
+					 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
+					 */
+					gpio26 {
+						gpio26_default_mode: gpio26_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio26_d_1";
+							};
+							default_cfg {
+								pins = "GPIO26_M16";
+								output-low;
+							};
+						};
+					};
+					gpio35 {
+						gpio35_default_mode: gpio35_default {
+							default_mux {
+								function = "gpio";
+								groups = "gpio35_d_1";
+							};
+							default_cfg {
+								pins = "GPIO35_W15";
+								output-low;
+							};
+						};
+					};
+					/*
+					 * This sets up the YCBCR connector pins, i.e. analog video out.
+					 * Set as input with no bias.
+					 */
+					ycbcr {
+						ycbcr_default_mode: ycbcr_default {
+							default_mux {
+								function = "ycbcr";
+								groups = "ycbcr0123_d_1";
+							};
+							default_cfg {
+								pins = "GPIO6_Y18",
+									 "GPIO7_AA20",
+									 "GPIO8_W18",
+									 "GPIO9_AA19";
+								input-enable;
+								bias-disable;
+							};
+						};
+					};
+					/* This sets up the PWM pins 14 and 15 */
+					pwm {
+						pwm_default_mode: pwm_default {
+							default_mux {
+								function = "pwmout";
+								groups = "pwmout1_d_1", "pwmout2_d_1";
+							};
+							default_cfg {
+								pins = "GPIO14_F14",
+									 "GPIO15_B17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up audio interface 1 */
+					adi1 {
+						adi1_default_mode: adi1_default {
+							default_mux {
+								function = "adi1";
+								groups = "adi1_d_1";
+							};
+							default_cfg {
+								pins = "GPIO17_P5",
+									 "GPIO18_R5",
+									 "GPIO19_U5",
+									 "GPIO20_T5";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up the USB UICC pins */
+					usbuicc {
+						usbuicc_default_mode: usbuicc_default {
+							default_mux {
+								function = "usbuicc";
+								groups = "usbuicc_d_1";
+							};
+							default_cfg {
+								pins = "GPIO21_H19",
+									 "GPIO22_G20",
+									 "GPIO23_G19";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* This sets up the microphone pins */
+					dmic {
+						dmic_default_mode: dmic_default {
+							default_mux {
+								function = "dmic";
+								groups = "dmic12_d_1",
+									 "dmic34_d_1",
+									 "dmic56_d_1";
+							};
+							default_cfg {
+								pins = "GPIO27_J6",
+									 "GPIO28_K6",
+									 "GPIO29_G6",
+									 "GPIO30_H6",
+									 "GPIO31_F5",
+									 "GPIO32_G5";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					extcpena {
+						extcpena_default_mode: extcpena_default {
+							default_mux {
+								function = "extcpena";
+								groups = "extcpena_d_1";
+							};
+							default_cfg {
+								pins = "GPIO34_R17";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/* Modem I2C setup (SCL and SDA pins) */
+					modsclsda {
+						modsclsda_default_mode: modsclsda_default {
+							default_mux {
+								function = "modsclsda";
+								groups = "modsclsda_d_1";
+							};
+							default_cfg {
+								pins = "GPIO40_T19",
+									"GPIO41_U19";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					/*
+					 * Clock output pins associated with regulators.
+					 */
+					sysclkreq2 {
+						sysclkreq2_default_mode: sysclkreq2_default {
+							default_mux {
+								function = "sysclkreq";
+								groups = "sysclkreq2_d_1";
+							};
+							default_cfg {
+								pins = "GPIO1_T10";
+								input-enable;
+								bias-disable;
+							};
+						};
+						sysclkreq2_sleep_mode: sysclkreq2_sleep {
+							default_mux {
+								function = "gpio";
+								groups = "gpio1_a_1";
+							};
+							default_cfg {
+								pins = "GPIO1_T10";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+					sysclkreq4 {
+						sysclkreq4_default_mode: sysclkreq4_default {
+							default_mux {
+								function = "sysclkreq";
+								groups = "sysclkreq4_d_1";
+							};
+							default_cfg {
+								pins = "GPIO3_U9";
+								input-enable;
+								bias-disable;
+							};
+						};
+						sysclkreq4_sleep_mode: sysclkreq4_sleep {
+							default_mux {
+								function = "gpio";
+								groups = "gpio3_a_1";
+							};
+							default_cfg {
+								pins = "GPIO3_U9";
+								input-enable;
+								bias-pull-down;
+							};
+						};
+					};
+				};
+				/*
+				 * Charging is not working on the HREF unless an actual battery is
+				 * mounted, most HREFs have a DC cable in to the "battery power"
+				 * which means this will only be cofusing. So do not enable charging
+				 * of the HREFs.
+				 */
+				ab8500_fg {
+					status = "disabled";
+				};
+				ab8500_btemp {
+					status = "disabled";
+				};
+				ab8500_charger {
+					status = "disabled";
+				};
+				ab8500_chargalg {
+					status = "disabled";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi
new file mode 100644
index 000000000000..434fa6baf71f
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-family-pinctrl.dtsi
@@ -0,0 +1,212 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Linaro Ltd.
+ */
+
+#include "ste-dbx5x0-pinctrl.dtsi"
+
+/ {
+	soc {
+		pinctrl {
+			/* Settings for all SPI default and sleep states */
+			spi2 {
+				spi2_default_mode: spi_default {
+					default_mux {
+						function = "spi2";
+						groups = "spi2_oc1_2";
+					};
+					default_cfg1 {
+						pins = "GPIO216_AG12"; /* FRM */
+						ste,config = <&gpio_out_hi>;
+					};
+					default_cfg2 {
+						pins = "GPIO218_AH11"; /* RXD */
+						ste,config = <&in_pd>;
+					};
+					default_cfg3 {
+						pins =
+						"GPIO215_AH13", /* TXD */
+						"GPIO217_AH12"; /* CLK */
+						ste,config = <&out_lo>;
+					};
+				};
+
+				spi2_idle_mode: spi_idle {
+					/*
+					 * The idle mode is basically sleep mode sans wakeups. Also
+					 * note that we have muxes the pins off the function here
+					 * as we do not state any muxing.
+					 */
+					idle_cfg1 {
+						pins = "GPIO218_AH11"; /* RXD */
+						ste,config = <&slpm_in_pdis>;
+					};
+					idle_cfg2 {
+						pins = "GPIO215_AH13"; /* TXD */
+						ste,config = <&slpm_out_lo_pdis>;
+					};
+					idle_cfg3 {
+						pins = "GPIO217_AH12"; /* CLK */
+						ste,config = <&slpm_pdis>;
+					};
+				};
+
+				spi2_sleep_mode: spi_sleep {
+					sleep_cfg1 {
+						pins =
+						"GPIO216_AG12", /* FRM */
+						"GPIO218_AH11"; /* RXD */
+						ste,config = <&slpm_in_wkup_pdis>;
+					};
+					sleep_cfg2 {
+						pins = "GPIO215_AH13"; /* TXD */
+						ste,config = <&slpm_out_lo_wkup_pdis>;
+					};
+					sleep_cfg3 {
+						pins = "GPIO217_AH12"; /* CLK */
+						ste,config = <&slpm_wkup_pdis>;
+					};
+				};
+			};
+
+			mcde {
+				lcd_default_mode: lcd_default {
+					default_mux1 {
+						/* Mux in VSI0 and all the data lines */
+						function = "lcd";
+						groups =
+						"lcdvsi0_a_1", /* VSI0 for LCD */
+						"lcd_d0_d7_a_1", /* Data lines */
+						"lcdvsi1_a_1"; /* VSI1 for HDMI */
+					};
+					default_mux2 {
+						function = "lcda";
+						groups =
+						"lcdaclk_b_1"; /* Clock line for TV-out */
+					};
+					default_cfg1 {
+						pins =
+						"GPIO68_E1", /* VSI0 */
+						"GPIO69_E2"; /* VSI1 */
+						ste,config = <&in_pu>;
+					};
+				};
+				lcd_sleep_mode: lcd_sleep {
+					sleep_cfg1 {
+						pins = "GPIO69_E2"; /* VSI1 */
+						ste,config = <&slpm_in_wkup_pdis>;
+					};
+				};
+			};
+
+			ske {
+				/* SKE keys on position 2 in an 8x8 matrix */
+				ske_kpa2_default_mode: ske_kpa2_default {
+					default_mux {
+						function = "kp";
+						groups = "kp_a_2";
+					};
+					default_cfg1 {
+						pins =
+						"GPIO153_B17", /* I7 */
+						"GPIO154_C16", /* I6 */
+						"GPIO155_C19", /* I5 */
+						"GPIO156_C17", /* I4 */
+						"GPIO161_D21", /* I3 */
+						"GPIO162_D20", /* I2 */
+						"GPIO163_C20", /* I1 */
+						"GPIO164_B21"; /* I0 */
+						ste,config = <&in_pd>;
+					};
+					default_cfg2 {
+						pins =
+						"GPIO157_A18", /* O7 */
+						"GPIO158_C18", /* O6 */
+						"GPIO159_B19", /* O5 */
+						"GPIO160_B20", /* O4 */
+						"GPIO165_C21", /* O3 */
+						"GPIO166_A22", /* O2 */
+						"GPIO167_B24", /* O1 */
+						"GPIO168_C22"; /* O0 */
+						ste,config = <&out_lo>;
+					};
+				};
+				ske_kpa2_sleep_mode: ske_kpa2_sleep {
+					sleep_cfg1 {
+						pins =
+						"GPIO153_B17", /* I7 */
+						"GPIO154_C16", /* I6 */
+						"GPIO155_C19", /* I5 */
+						"GPIO156_C17", /* I4 */
+						"GPIO161_D21", /* I3 */
+						"GPIO162_D20", /* I2 */
+						"GPIO163_C20", /* I1 */
+						"GPIO164_B21"; /* I0 */
+						ste,config = <&slpm_in_pu_wkup_pdis_en>;
+					};
+					sleep_cfg2 {
+						pins =
+						"GPIO157_A18", /* O7 */
+						"GPIO158_C18", /* O6 */
+						"GPIO159_B19", /* O5 */
+						"GPIO160_B20", /* O4 */
+						"GPIO165_C21", /* O3 */
+						"GPIO166_A22", /* O2 */
+						"GPIO167_B24", /* O1 */
+						"GPIO168_C22"; /* O0 */
+						ste,config = <&slpm_out_lo_pdis>;
+					};
+				};
+				/*
+				 * SKE keys on position 1 and "other C1" combi giving
+				 * six rows of six keys.
+				 */
+				ske_kpaoc1_default_mode: ske_kpaoc1_default {
+					default_mux {
+						function = "kp";
+						groups = "kp_a_1", "kp_oc1_1";
+					};
+					default_cfg1 {
+						pins =
+						"GPIO91_B6", /* KP_O0 */
+						"GPIO90_A3", /* KP_O1 */
+						"GPIO87_B3", /* KP_O2 */
+						"GPIO86_C6", /* KP_O3 */
+						"GPIO96_D8", /* KP_O6 */
+						"GPIO94_D7"; /* KP_O7 */
+						ste,config = <&out_lo>;
+					};
+					default_cfg2 {
+						pins =
+						"GPIO93_B7", /* KP_I0 */
+						"GPIO92_D6", /* KP_I1 */
+						"GPIO89_E6", /* KP_I2 */
+						"GPIO88_C4", /* KP_I3 */
+						"GPIO97_D9", /* KP_I6 */
+						"GPIO95_E8"; /* KP_I7 */
+						ste,config = <&in_pu>;
+					};
+				};
+			};
+
+			wlan {
+				wlan_default_mode: wlan_default {
+					/*
+					 * Activate this mode with the WLAN chip.
+					 * These are plain GPIO pins used by WLAN
+					 */
+					default_cfg1 {
+						pins =
+						"GPIO226_AF8", /* WLAN_PMU_EN */
+						"GPIO85_D5"; /* WLAN_ENA */
+						ste,config = <&gpio_out_lo>;
+					};
+					default_cfg2 {
+						pins = "GPIO4_AH6"; /* WLAN_IRQ on UART1 */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-stuib.dtsi b/arch/arm/boot/dts/st/ste-href-stuib.dtsi
new file mode 100644
index 000000000000..79c2be36acae
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-stuib.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&ab8500_ldo_aux1_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>;
+
+		button@139 {
+			/* Proximity sensor */
+			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+			linux,code = <11>; /* SW_FRONT_PROXIMITY */
+			label = "SFH7741 Proximity Sensor";
+		};
+		button@145 {
+			/* Hall sensor */
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			linux,code = <0>; /* SW_LID */
+			label = "HED54XXU11 Hall Effect Sensor";
+		};
+	};
+
+	soc {
+		i2c@80004000 {
+			stmpe1601: port-expander@40 {
+				compatible = "st,stmpe1601";
+				reg = <0x40>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-parent = <&gpio6>;
+				vcc-supply = <&db8500_vsmps2_reg>;
+				vio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&stmpe_stuib_mode>;
+
+				wakeup-source;
+				st,autosleep-timeout = <1024>;
+
+				keyboard-controller {
+					compatible = "st,stmpe-keypad";
+
+					debounce-interval = <64>;
+					st,scan-count = <8>;
+					st,no-autorepeat;
+
+					linux,keymap = <0x205006b
+							0x4010074
+							0x3050072
+							0x1030004
+							0x502006a
+							0x500000a
+							0x5008b
+							0x706001c
+							0x405000b
+							0x6070003
+							0x3040067
+							0x303006c
+							0x60400e7
+							0x602009e
+							0x4020073
+							0x5050002
+							0x4030069
+							0x3020008>;
+				};
+			};
+		};
+
+		/* Sensors mounted on this board variant */
+		i2c@80128000 {
+			lis331dl@1c {
+				/* Accelerometer */
+				compatible = "st,lis331dl-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x1c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_stuib_mode>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+					     <19 IRQ_TYPE_EDGE_RISING>;
+			};
+			ak8974@f {
+				/* Magnetometer */
+				compatible = "asahi-kasei,ak8974";
+				reg = <0x0f>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&magneto_stuib_mode>;
+				interrupt-parent = <&gpio1>;
+				interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
+		i2c@80110000 {
+			bu21013_tp@5c {
+				compatible = "rohm,bu21013_tp";
+				reg = <0x5c>;
+				avdd-supply = <&ab8500_ldo_aux1_reg>;
+
+				rohm,touch-max-x = <384>;
+				rohm,touch-max-y = <704>;
+				rohm,flip-y;
+				pinctrl-names = "default";
+				pinctrl-0 = <&touch_rohm_mode>;
+			};
+
+			bu21013_tp@5d {
+				compatible = "rohm,bu21013_tp";
+				reg = <0x5d>;
+				avdd-supply = <&ab8500_ldo_aux1_reg>;
+
+				rohm,touch-max-x = <384>;
+				rohm,touch-max-y = <704>;
+				rohm,flip-y;
+				pinctrl-names = "default";
+				pinctrl-0 = <&touch_rohm_mode>;
+			};
+		};
+
+		pinctrl {
+			/* Pull up this GPIO pin */
+			stmpe {
+				stmpe_stuib_mode: stmpe_stuib {
+					stuib_cfg {
+						ste,pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			prox {
+				prox_stuib_mode: prox_stuib {
+					stuib_cfg {
+						pins = "GPIO217_AH12";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			hall {
+				hall_stuib_mode: stuib_tvk {
+					stuib_cfg {
+						pins = "GPIO145_C13";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			accelerometer {
+				accel_stuib_mode: accel_stuib {
+					/* Accelerometer interrupt lines 1 & 2 */
+					stuib_cfg {
+						pins = "GPIO82_C1", "GPIO83_D3";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			magnetometer {
+				magneto_stuib_mode: magneto_stuib {
+					/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+					stuib_cfg1 {
+						pins = "GPIO31_V3";
+						ste,config = <&gpio_in_pu>;
+					};
+					stuib_cfg2 {
+						pins = "GPIO32_V2";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			touch {
+				touch_rohm_mode: touch_rohm {
+					/*
+					 * ROHM touch screen uses GPIO 143 for
+					 * RST1, GPIO 146 for RST2 and
+					 * GPIO 67 for interrupts. Pull-up
+					 * the IRQ line and drive both
+					 * reset signals low.
+					 */
+					stuib_cfg1 {
+						pins = "GPIO143_D12", "GPIO146_D13";
+						ste,config = <&gpio_out_lo>;
+					};
+					stuib_cfg2 {
+						pins = "GPIO67_G2";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+
+			dsi@a0351000 {
+				panel {
+					compatible = "samsung,s6d16d0";
+					reg = <0>;
+					vdd1-supply = <&ab8500_ldo_aux1_reg>;
+					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi
new file mode 100644
index 000000000000..37e59403c01f
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-tvk1281618-r2.dtsi
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the TVK1281618 R2 user interface board (UIB)
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&ab8500_ldo_aux1_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
+
+		button@139 {
+			/* Proximity sensor */
+			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+			linux,code = <11>; /* SW_FRONT_PROXIMITY */
+			label = "SFH7741 Proximity Sensor";
+		};
+		button@145 {
+			/* Hall sensor */
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			linux,code = <0>; /* SW_LID */
+			label = "HED54XXU11 Hall Effect Sensor";
+		};
+	};
+
+	soc {
+		i2c@80004000 {
+			tc35893@44 {
+				compatible = "toshiba,tc35893";
+				reg = <0x44>;
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35893_tvk_mode>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				status = "disabled";
+
+				tc3589x_gpio {
+					compatible = "toshiba,tc3589x-gpio";
+					interrupts = <0>;
+
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+				tc3589x_keypad {
+					compatible = "toshiba,tc3589x-keypad";
+					interrupts = <6>;
+					debounce-delay-ms = <4>;
+					keypad,num-columns = <8>;
+					keypad,num-rows = <8>;
+					linux,no-autorepeat;
+					wakeup-source;
+					linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
+						       <MATRIX_KEY(4, 1, KEY_HOME)>,
+						       <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
+						       <MATRIX_KEY(4, 2, KEY_EMAIL)>,
+						       <MATRIX_KEY(3, 3, KEY_RIGHT)>,
+						       <MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
+						       <MATRIX_KEY(6, 7, KEY_MENU)>,
+						       <MATRIX_KEY(5, 0, KEY_ENTER)>,
+						       <MATRIX_KEY(4, 3, KEY_0)>,
+						       <MATRIX_KEY(3, 4, KEY_DOT)>,
+						       <MATRIX_KEY(5, 2, KEY_UP)>,
+						       <MATRIX_KEY(3, 5, KEY_DOWN)>,
+						       <MATRIX_KEY(4, 5, KEY_SEND)>,
+						       <MATRIX_KEY(0, 5, KEY_BACK)>,
+						       <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
+						       <MATRIX_KEY(1, 3, KEY_SPACE)>,
+						       <MATRIX_KEY(7, 6, KEY_LEFT)>,
+						       <MATRIX_KEY(5, 5, KEY_SEARCH)>;
+				};
+			};
+		};
+
+		i2c@80128000 {
+			accelerometer@18 {
+				/* Accelerometer */
+				compatible = "st,lsm303dlh-accel";
+				st,drdy-int-pin = <1>;
+				drive-open-drain;
+				reg = <0x18>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_tvk_mode>;
+				/*
+				 * These interrupts cannot be used: the other component
+				 * ST-Micro L3D4200D gyro that is connected to the same lines
+				 * cannot set its DRDY line to open drain, so it cannot be
+				 * shared with other peripherals. The should be defined for
+				 * the falling edge if they could be wired together.
+				 *
+				 * interrupts-extended =
+				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
+				 */
+				mount-matrix = "0", "1", "0",
+					       "1", "0", "0",
+					       "0", "0", "-1";
+			};
+			magnetometer@1e {
+				/* Magnetometer */
+				compatible = "st,lsm303dlh-magn";
+				reg = <0x1e>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				/*
+				 * These interrupts cannot be used: the other component
+				 * ST-Micro L3D4200D gyro that is connected to the same lines
+				 * cannot set its DRDY line to open drain, so it cannot be
+				 * shared with other peripherals. The should be defined for
+				 * the falling edge if they could be wired together.
+				 *
+				 * interrupts-extended =
+				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
+				 */
+			};
+			accelerometer@1c {
+				/* Accelerometer */
+				compatible = "st,lis331dl-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x1c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_tvk_mode>;
+				interrupt-parent = <&gpio2>;
+				/* INT2 would need to be open drain */
+				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+					     <19 IRQ_TYPE_EDGE_RISING>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
+			};
+			magnetometer@f {
+				/* Magnetometer */
+				compatible = "asahi-kasei,ak8974";
+				reg = <0x0f>;
+				avdd-supply = <&ab8500_ldo_aux1_reg>;
+				dvdd-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gyro_magn_tvk_mode>;
+				/*
+				 * These interrupts cannot be used: the other component
+				 * ST-Micro L3D4200D gyro that is connected to the same lines
+				 * cannot set its DRDY line to open drain, so it cannot be
+				 * shared with other peripherals. The should be defined for
+				 * the falling edge if they could be wired together.
+				 *
+				 * interrupts-extended =
+				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+				 * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
+				 */
+			};
+			gyroscope@68 {
+				/* Gyroscope */
+				compatible = "st,l3g4200d-gyro";
+				st,drdy-int-pin = <2>;
+				reg = <0x68>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gyro_magn_tvk_mode>;
+				interrupts-extended =
+				<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
+				<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
+			};
+			pressure@5c {
+				/* Barometer/pressure sensor */
+				compatible = "st,lps001wp-press";
+				reg = <0x5c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+		};
+		i2c@80110000 {
+			synaptics@4b {
+				/* Synaptics RMI4 TM1217 touchscreen */
+				compatible = "syna,rmi4-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x4b>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&synaptics_tvk_mode>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+
+				rmi4-f01@1 {
+					reg = <0x1>;
+					syna,nosleep = <1>;
+				};
+				rmi4-f11@11 {
+					reg = <0x11>;
+					syna,sensor-type = <1>;
+					/* This is a landscape display */
+					touchscreen-swapped-x-y;
+				};
+			};
+		};
+		mcde@a0350000 {
+			status = "okay";
+
+			dsi@a0351000 {
+				panel {
+					compatible = "samsung,s6d16d0";
+					reg = <0>;
+					vdd1-supply = <&ab8500_ldo_aux1_reg>;
+					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+		};
+		pinctrl {
+			prox {
+				prox_tvk_mode: prox_tvk {
+					tvk_cfg {
+						pins = "GPIO217_AH12";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			hall {
+				hall_tvk_mode: hall_tvk {
+					tvk_cfg {
+						pins = "GPIO145_C13";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			tc35893 {
+				/* IRQ from the TC35893 */
+				tc35893_tvk_mode: tc35893_tvk {
+					tvk_cfg {
+						pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			accelerometer {
+				accel_tvk_mode: accel_tvk {
+					/* Accelerometer interrupt lines 1 & 2 */
+					tvk_cfg {
+						pins = "GPIO82_C1", "GPIO83_D3";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			gyroscope {
+				/*
+				 * These lines are shared between Gyroscope l3g400dh
+				 * and AK8974 magnetometer.
+				 */
+				gyro_magn_tvk_mode: gyro_magn_tvk {
+					 /* GPIO 31 used for INT pull down the line */
+					tvk_cfg1 {
+						pins = "GPIO31_V3";
+						ste,config = <&gpio_in_pd>;
+					};
+					/* GPIO 32 used for DRDY, pull this down */
+					tvk_cfg2 {
+						pins = "GPIO32_V2";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			synaptics {
+				synaptics_tvk_mode: synaptics_tvk {
+					/* Touchscreen uses GPIO 84 */
+					tvk_cfg1 {
+						pins = "GPIO84_C2";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi
new file mode 100644
index 000000000000..00ce9d79f540
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href-tvk1281618-r3.dtsi
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the TVK1281618 R3 user interface board (UIB)
+ * also known as the "CYTTSP board"
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&ab8500_ldo_aux1_reg>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_tvk_mode>;
+
+		button@145 {
+			/* Hall sensor */
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			linux,code = <0>; /* SW_LID */
+			label = "HED54XXU11 Hall Effect Sensor";
+		};
+	};
+
+	soc {
+		i2c@80004000 {
+			tc35893@44 {
+				compatible = "toshiba,tc35893";
+				reg = <0x44>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35893_tvk_mode>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				status = "disabled";
+
+				tc3589x_gpio {
+					compatible = "toshiba,tc3589x-gpio";
+					interrupts = <0>;
+
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+				tc3589x_keypad {
+					compatible = "toshiba,tc3589x-keypad";
+					interrupts = <6>;
+					debounce-delay-ms = <4>;
+					keypad,num-columns = <8>;
+					keypad,num-rows = <8>;
+					linux,no-autorepeat;
+					wakeup-source;
+					linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>,
+						       <MATRIX_KEY(4, 1, KEY_HOME)>,
+						       <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>,
+						       <MATRIX_KEY(4, 2, KEY_EMAIL)>,
+						       <MATRIX_KEY(3, 3, KEY_RIGHT)>,
+						       <MATRIX_KEY(2, 5, KEY_BACKSPACE)>,
+						       <MATRIX_KEY(6, 7, KEY_MENU)>,
+						       <MATRIX_KEY(5, 0, KEY_ENTER)>,
+						       <MATRIX_KEY(4, 3, KEY_0)>,
+						       <MATRIX_KEY(3, 4, KEY_DOT)>,
+						       <MATRIX_KEY(5, 2, KEY_UP)>,
+						       <MATRIX_KEY(3, 5, KEY_DOWN)>,
+						       <MATRIX_KEY(4, 5, KEY_SEND)>,
+						       <MATRIX_KEY(0, 5, KEY_BACK)>,
+						       <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>,
+						       <MATRIX_KEY(1, 3, KEY_SPACE)>,
+						       <MATRIX_KEY(7, 6, KEY_LEFT)>,
+						       <MATRIX_KEY(5, 5, KEY_SEARCH)>;
+				};
+			};
+		};
+
+		i2c@80128000 {
+			accelerometer@19 {
+				compatible = "st,lsm303dlhc-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x19>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+					     <19 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_tvk_mode>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
+			};
+			magnetometer@1e {
+				compatible = "st,lsm303dlm-magn";
+				reg = <0x1e>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				// This interrupt is not properly working with the driver
+				// interrupt-parent = <&gpio1>;
+				// interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&magn_tvk_mode>;
+			};
+			gyroscope@68 {
+				/* Gyroscope */
+				compatible = "st,l3g4200d-gyro";
+				reg = <0x68>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+			pressure@5c {
+				/* Barometer/pressure sensor */
+				compatible = "st,lps001wp-press";
+				reg = <0x5c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+		};
+
+		spi@80111000 {
+			num-cs = <1>;
+			cs-gpios = <&gpio6 24 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi2_default_mode>;
+			status = "okay";
+
+			touchscreen@0 {
+				compatible = "cypress,cy8ctma340";
+				/*
+				 * Actually the max frequency is 6 MHz, but over 2 MHz the
+				 * data rate needs to be restricted to max 2Mbps which the
+				 * SPI framework cannot handle.
+				 */
+				spi-max-frequency = <2000000>;
+				reg = <0>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+				vcpin-supply = <&ab8500_ldo_aux1_reg>;
+				vdd-supply = <&db8500_vsmps2_reg>;
+				reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <854>;
+				active-interval-ms = <0>;
+				touch-timeout-ms = <255>;
+				lowpower-interval-ms = <10>;
+				bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&cyttsp_tvk_mode>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+
+			dsi@a0351000 {
+				panel {
+					compatible = "sony,acx424akp";
+					reg = <0>;
+					vddi-supply = <&ab8500_ldo_aux1_reg>;
+					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+		};
+
+		pinctrl {
+			hall {
+				hall_tvk_mode: hall_tvk {
+					tvk_cfg {
+						pins = "GPIO145_C13";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			tc35893 {
+				/* IRQ from the TC35893 */
+				tc35893_tvk_mode: tc35893_tvk {
+					tvk_cfg {
+						pins = "GPIO64_F3";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			accelerometer {
+				accel_tvk_mode: accel_tvk {
+					/* Accelerometer interrupt lines 1 & 2 */
+					tvk_cfg {
+						pins = "GPIO82_C1", "GPIO83_D3";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			magnetometer {
+				magn_tvk_mode: magn_tvk {
+					/* GPIO 32 used for DRDY, pull this down */
+					tvk_cfg {
+						pins = "GPIO32_V2";
+						ste,config = <&gpio_in_pd>;
+					};
+				};
+			};
+			cyttsp {
+				cyttsp_tvk_mode: cyttsp_tvk {
+					/* Touchscreen uses GPIO84 for IRQ */
+					tvk_cfg1 {
+						pins = "GPIO84_C2";
+						ste,config = <&gpio_in_pu>;
+					};
+					/* GPIO143 is reset */
+					tvk_cfg2 {
+						pins = "GPIO143_D12";
+						ste,config = <&gpio_out_hi>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href.dtsi b/arch/arm/boot/dts/st/ste-href.dtsi
new file mode 100644
index 000000000000..13b11dbeba1c
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href.dtsi
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include "ste-href-family-pinctrl.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+		battery-type = "lithium-ion-polymer";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	soc {
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* This UART is unused and thus left disabled */
+		serial@80121000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+		};
+
+		serial@80007000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+			status = "okay";
+		};
+
+		i2c@80004000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+			status = "okay";
+		};
+
+		i2c@80122000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+			status = "okay";
+		};
+
+		i2c@80128000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+			status = "okay";
+			lp5521@33 {
+				compatible = "national,lp5521";
+				reg = <0x33>;
+				label = "lp5521_pri";
+				clock-mode = /bits/ 8 <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				led@0 {
+					reg = <0>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+					linux,default-trigger = "heartbeat";
+				};
+				led@1 {
+					reg = <1>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+				};
+				led@2 {
+					reg = <2>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+				};
+			};
+			lp5521@34 {
+				compatible = "national,lp5521";
+				reg = <0x34>;
+				label = "lp5521_sec";
+				clock-mode = /bits/ 8 <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				led@0 {
+					reg = <0>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+				};
+				led@1 {
+					reg = <1>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+				};
+				led@2 {
+					reg = <2>;
+					led-cur = /bits/ 8 <0x2f>;
+					max-cur = /bits/ 8 <0x5f>;
+					color = <LED_COLOR_ID_BLUE>;
+				};
+			};
+			bh1780@29 {
+				compatible = "rohm,bh1780gli";
+				reg = <0x29>;
+			};
+		};
+
+		i2c@80110000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+			status = "okay";
+		};
+
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			full-pwr-cycle;
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-dir-cmd;
+			st,sig-pin-fbclk;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&vmmci>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			non-removable;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_1_default>;
+			pinctrl-1 = <&mc1_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		// PoP:ed eMMC
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			cap-mmc-highspeed;
+			non-removable;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&db8500_vsmps2_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		// On-board eMMC
+		mmc@80114000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			cap-mmc-highspeed;
+			non-removable;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ab8500_ldo_aux2_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc4_a_1_default>;
+			pinctrl-1 = <&mc4_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		msp0: msp@80123000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
+			status = "okay";
+		};
+
+		msp1: msp@80124000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp1txrx_a_1_default>;
+			status = "okay";
+		};
+
+		msp2: msp@80117000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp2_a_1_default>;
+		};
+
+		msp3: msp@80125000 {
+			status = "okay";
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				gpio {
+				};
+
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+			};
+		};
+
+		pinctrl {
+			sdi0 {
+				sdi0_default_mode: sdi0_default {
+					/* Some boards set additional settings here */
+				};
+			};
+		};
+
+		mcde@a0350000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&lcd_default_mode>;
+			pinctrl-1 = <&lcd_sleep_mode>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-href520-tvk.dts b/arch/arm/boot/dts/st/ste-href520-tvk.dts
new file mode 100644
index 000000000000..4201547c5988
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-href520-tvk.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the HREF520 version with the TVK1281618 R3 UIB
+ */
+
+/dts-v1/;
+#include "ste-db8520.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618-r3.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF520 and TVK1281618 R3 UIB";
+	compatible = "st-ericsson,href520", "st-ericsson,u8500";
+
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio2 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_href520_cfg1 {
+				pins = "GPIO78_F4";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_href520_cfg2 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts b/arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts
new file mode 100644
index 000000000000..dfc933214c1a
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefprev60-stuib.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	soc {
+		/* Reset line for the BU21013 touchscreen */
+		i2c@80110000 {
+			/* Only one of these will be used */
+			bu21013_tp@5c {
+				interrupt-parent = <&gpio2>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&tc3589x_gpio 13 GPIO_LINE_OPEN_DRAIN>;
+			};
+			bu21013_tp@5d {
+				interrupt-parent = <&gpio2>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&tc3589x_gpio 13 GPIO_LINE_OPEN_DRAIN>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts
new file mode 100644
index 000000000000..75506339a93c
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefprev60-tvk.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-hrefprev60.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (pre-v60) and TVK1281618 R2 UIB";
+	compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefprev60.dtsi b/arch/arm/boot/dts/st/ste-hrefprev60.dtsi
new file mode 100644
index 000000000000..9859ee91a15e
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefprev60.dtsi
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * Device Tree for the HREF+ prior to the v60 variant.
+ */
+
+#include "ste-href-ab8500.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+	gpio_keys {
+		button@1 {
+			gpios = <&tc3589x_gpio 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	soc {
+		/* Enable UART1 on this board */
+		serial@80121000 {
+			status = "okay";
+		};
+
+		i2c@80004000 {
+			tps61052@33 {
+				compatible = "ti,tps61052";
+				reg = <0x33>;
+			};
+
+			tc35892@42 {
+				compatible = "toshiba,tc35892";
+				reg = <0x42>;
+				interrupt-parent = <&gpio6>;
+				interrupts = <25 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tc35892_hrefprev60_mode>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				tc3589x_gpio: tc3589x_gpio {
+					compatible = "tc3589x-gpio";
+					interrupts = <0>;
+
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+			};
+		};
+
+		spi@80002000 {
+			/*
+			 * On the first generation boards, this SSP/SPI port was connected
+			 * to the AB8500.
+			 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&ssp0_hrefprev60_mode>;
+			status = "okay";
+		};
+
+		// External Micro SD slot
+		mmc@80126000 {
+			cd-gpios  = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		pinctrl {
+			/* Set this up using hogs */
+			pinctrl-names = "default";
+			pinctrl-0 = <&ipgpio_hrefprev60_mode>;
+
+			ssp0 {
+				ssp0_hrefprev60_mode: ssp0_hrefprev60_default {
+					hrefprev60_mux {
+						function = "ssp0";
+						groups = "ssp0_a_1";
+					};
+					hrefprev60_cfg1 {
+						pins = "GPIO145_C13"; /* RXD */
+						ste,config = <&in_pd>;
+					};
+
+				};
+			};
+			sdi0 {
+				/* This additional pin needed on early MOP500 and HREFs previous to v60 */
+				sdi0_default_mode: sdi0_default {
+					hrefprev60_mux {
+						function = "mc0";
+						groups = "mc0dat31dir_a_1";
+					};
+					hrefprev60_cfg1 {
+						pins = "GPIO21_AB3"; /* DAT31DIR */
+						ste,config = <&out_hi>;
+					};
+
+				};
+			};
+			tc35892 {
+				tc35892_hrefprev60_mode: tc35892_hrefprev60 {
+					hrefprev60_cfg {
+						pins = "GPIO217_AH12";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			ipgpio {
+				 ipgpio_hrefprev60_mode: ipgpio_hrefprev60 {
+					hrefprev60_mux {
+						function = "ipgpio";
+						groups = "ipgpio0_c_1", "ipgpio1_c_1";
+					};
+					hrefprev60_cfg1 {
+						pins = "GPIO6_AF6", "GPIO7_AG5";
+						ste,config = <&in_pu>;
+					};
+				 };
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts
new file mode 100644
index 000000000000..52c56ed17ae6
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus-stuib.dts
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * Device Tree for the HREF version 60 or later with the ST UIB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-stuib.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) and ST UIB";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+
+	soc {
+		/* Reset line for the BU21013 touchscreen */
+		i2c@80110000 {
+			/* Only one of these will be used */
+			bu21013_tp@5c {
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
+			};
+			bu21013_tp@5d {
+				interrupt-parent = <&gpio2>;
+				interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+				touch-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+				reset-gpios = <&gpio4 17 GPIO_LINE_OPEN_DRAIN>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_hrefv60_cfg2 {
+				pins = "GPIO169_D22";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_hrefv60_cfg3 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts
new file mode 100644
index 000000000000..2db2f8be8b03
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus-tvk.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ *
+ * Device Tree for the HREF version 60 or later with the TVK1281618 R2 UIB
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-hrefv60plus.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) and TVK1281618 R2 UIB";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	/* ST6G3244ME level translator for 1.8/2.9 V */
+	vmmci: regulator-gpio {
+		compatible = "regulator-gpio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-name = "mmci-reg";
+		regulator-type = "voltage";
+
+		startup-delay-us = <100>;
+
+		states = <1800000 0x1
+			  2900000 0x0>;
+
+		gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vmmci_default_mode>;
+	};
+};
+
+&pinctrl {
+	vmmci {
+		vmmci_default_mode: vmmc_default {
+			/* VMMCI level-shifter enable */
+			default_hrefv60_cfg2 {
+				pins = "GPIO169_D22";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* VMMCI level-shifter voltage select */
+			default_hrefv60_cfg3 {
+				pins = "GPIO5_AG6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/st/ste-hrefv60plus.dtsi
new file mode 100644
index 000000000000..e66fa59c2de6
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-hrefv60plus.dtsi
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+#include "ste-href-ab8500.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+	model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+	compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+	thermal-zones {
+		chassis-thermal {
+			/* Poll every 20 seconds */
+			polling-delay = <20000>;
+			/* Poll every 2nd second when cooling */
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&therm1>, <&therm2>;
+
+			/* Tripping points made from rough guess about operating conditions */
+			trips {
+				chassis_alert: chassis-alert {
+					/* At 50 degrees take down the CPU frequency */
+					temperature = <50000>;
+					hysteresis = <3000>;
+					type = "active";
+				};
+				chassis_crit: chassis-crit {
+					/* Just shut down at 70 degrees */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			/* Push down the operating frequency of the SoC when it gets hot */
+			cooling-maps {
+				map0 {
+					trip = <&chassis_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+					contribution = <100>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Thermistors on the board, formally to monitor battery temperatures
+	 * but what they measure is the board temperature.
+	 */
+	therm1: thermistor@0 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x06>; /* AUX1 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	therm2: thermistor@1 {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x07>; /* AUX2 */
+		pullup-uv = <1800000>;
+		pullup-ohm = <220000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	soc {
+		/* Name the GPIO muxed rails on the HREF boards */
+		gpio@8012e000 {
+			/* GPIOs 0 - 31 */
+			gpio-line-names =
+				     /* GPIO0,1 used for UART0 BT RX/TX */
+				     "", "",
+				     "UART_WAKE",
+				     "BT_WAKE",
+				     "",
+				     "SDMMC_1V8_3V_SEL",
+				     "FLASH_LED_SYNC (FLASH_CTRL_0)",
+				     "XENON_READY (FLASH_CTRL_1)",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "",
+				     "",
+				     "FLASH_LED_EN (FLASH_CTRL_3)",
+				     "", "",
+				     "", "", "", "", "",
+				     /* Used by UART2 (console) */
+				     "", "",
+				     "MAGNETOMETER_INT";
+		};
+
+		gpio@8012e080 {
+			/* GPIOs 32 - 63 */
+			gpio-line-names =
+				     "MAGNETOMETER_DRDY",
+				     "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e000 {
+			/* GPIOs 64 - 95 */
+			gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
+				     "DISP1_RST",
+				     "DISP2_RST",
+				     "TOUCH_INT2",
+				     "LCD_VSI0_A",
+				     "LCD_VSI1_A",
+				     /* GPIO 70-77 used for ETM */
+				     "", "", "", "", "", "", "", "",
+				     /* GPIO 78-81 used for YCBCR */
+				     "", "", "", "",
+				     "ACCELEROMETER_INT1_RDY",
+				     "ACCELEROMETER_INT2",
+				     "TOUCH_INT",
+				     "WLAN_ENA",
+				     "", "", "", "", "",
+				     "FORCE_SENSING_INT",
+				     "FORCE_SENSING_RESET",
+				     "", "",
+				     "SDMMC_CD";
+		};
+
+		gpio@8000e080 {
+			/* GPIOs 96 - 127 */
+			gpio-line-names = "",
+				     "FORCE_SENSING_WU",
+				     "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e100 {
+			/* GPIOs 128 - 159 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "", "", "",
+				     "DIPRO_INT", /* GPIO139 */
+				     "XSHUTDOWN_SECONDARY_SENSOR",
+				     "XSHUTDOWN_PRIMARY_SENSOR",
+				     "NFC_RST (NFC_CTRL_",
+				     "TOUCH_RST",
+				     "NFC_IRQ (NFC_CTRL_1)",
+				     "HAL_SW",
+				     "TOUCH_RST2",
+				     "", "",
+				     "VAUDIO_HF_EN", /* GPIO149 */
+				     "", "", "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e180 {
+			/* GPIOs 160 - 191 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "",
+				     "SDMMC_EN",
+				     "XENON_CHARGE (FLASH_CONTROL_5)",
+				     "GBF_ENA_RESET",
+				     "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8011e000 {
+			/* GPIOs 192 - 223 */
+			gpio-line-names = "HDTV_INTN",
+				     "", "", "",
+				     "HDTV_RSTN",
+				     "", "", "",
+				     "", /* GPIO200 */
+				     "", "", "", "", "", "", "",
+				     /* GPIO208-216 used for WGBF_MC1 */
+				     "", "", "", "", "", "", "", "", "",
+				     "SW_FRONT_PROXIMITY", /* GPIO217 */
+				     "KPD_CTRL_INT", /* Keypad controller */
+				     "", "", "", "", "";
+		};
+
+		gpio@8011e080 {
+			/* GPIOs 224 - 255 */
+			gpio-line-names = "", "",
+				     "HSIT_ACWAKE0",
+				     "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		// External Micro SD slot
+		mmc@80126000 {
+			cd-gpios  = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
+		};
+
+		pinctrl {
+			/*
+			 * Set this up using hogs, as time goes by and as seems fit, these
+			 * can be moved over to being controlled by respective device.
+			 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&ipgpio_hrefv60_mode>,
+				  <&etm_hrefv60_mode>,
+				  <&nahj_hrefv60_mode>,
+				  <&nfc_hrefv60_mode>,
+				  <&force_hrefv60_mode>,
+				  <&dipro_hrefv60_mode>,
+				  <&vaudio_hf_hrefv60_mode>,
+				  <&gbf_hrefv60_mode>,
+				  <&hdtv_hrefv60_mode>,
+				  <&gpios_hrefv60_mode>;
+
+			sdi0 {
+				sdi0_default_mode: sdi0_default {
+					/* SD card detect GPIO pin, extend default state */
+					default_hrefv60_cfg1 {
+						pins = "GPIO95_E8";
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			ipgpio {
+				/*
+				 * XENON Flashgun on image processor GPIO (controlled from image
+				 * processor firmware), mux in these image processor GPIO lines 0
+				 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+				 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+				 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+				 */
+				ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+					hrefv60_mux {
+						function = "ipgpio";
+						groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+					};
+					hrefv60_cfg1 {
+						pins = "GPIO6_AF6", "GPIO7_AG5";
+						ste,config = <&in_pu>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO21_AB3";
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg3 {
+						pins = "GPIO64_F3";
+						ste,config = <&out_lo>;
+					};
+				};
+			};
+			etm {
+				/*
+				 * Drive D19-D23 for the ETM PTM trace interface low,
+				 * (presumably pins are unconnected therefore grounded here,
+				 * the "other alt C1" setting enables these pins)
+				 */
+				etm_hrefv60_mode: etm_hrefv60 {
+					hrefv60_cfg1 {
+						pins =
+						"GPIO70_G5",
+						"GPIO71_G4",
+						"GPIO72_H4",
+						"GPIO73_H3",
+						"GPIO74_J3";
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			nahj {
+				nahj_hrefv60_mode: nahj_hrefv60 {
+					/* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+					hrefv60_cfg1 {
+						pins = "GPIO76_J2";
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO216_AG12";
+						ste,config = <&gpio_out_hi>;
+					};
+				 };
+			};
+			nfc {
+				nfc_hrefv60_mode: nfc_hrefv60 {
+					/* NFC ENA and RESET to low, pulldown IRQ line */
+					hrefv60_cfg1 {
+						pins =
+						"GPIO77_H1", /* NFC_ENA */
+						"GPIO142_C11"; /* NFC_RESET */
+						ste,config = <&gpio_out_lo>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO144_B13"; /* NFC_IRQ */
+						ste,config = <&gpio_in_pd>;
+					};
+				 };
+			};
+			force {
+				force_hrefv60_mode: force_hrefv60 {
+					hrefv60_cfg1 {
+						pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+						ste,config = <&gpio_in_pu>;
+					};
+					hrefv60_cfg2 {
+						pins =
+						"GPIO92_D6", /* FORCE_SENSING_RST */
+						"GPIO97_D9"; /* FORCE_SENSING_WU */
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			dipro {
+				dipro_hrefv60_mode: dipro_hrefv60 {
+					hrefv60_cfg1 {
+						pins = "GPIO139_C9"; /* DIPRO_INT */
+						ste,config = <&gpio_in_pu>;
+					};
+				 };
+			};
+			vaudio_hf {
+				vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+					/* Audio Amplifier HF enable GPIO */
+					hrefv60_cfg1 {
+						pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+						ste,config = <&gpio_out_hi>;
+					};
+				 };
+			};
+			gbf {
+				gbf_hrefv60_mode: gbf_hrefv60 {
+					/*
+					 * GBF (GPS, Bluetooth, FM-radio) interface,
+					 * pull low to reset state
+					 */
+					hrefv60_cfg1 {
+						pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			hdtv {
+				hdtv_hrefv60_mode: hdtv_hrefv60 {
+					/* MSP : HDTV INTERFACE GPIO line */
+					hrefv60_cfg1 {
+						pins = "GPIO192_AJ27";
+						ste,config = <&gpio_in_pd>;
+					};
+				 };
+			};
+			mcde {
+				lcd_hrefv60_mode: lcd_hrefv60 {
+					/*
+					 * Display Interface 1 uses GPIO 65 for RST (reset).
+					 * Display Interface 2 uses GPIO 66 for RST (reset).
+					 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+					 */
+					hrefv60_cfg1 {
+						pins = "GPIO65_F1";
+						ste,config = <&gpio_out_hi>;
+					};
+					hrefv60_cfg2 {
+						pins = "GPIO66_G3";
+						ste,config = <&gpio_out_lo>;
+					};
+				};
+			};
+			gpios {
+				/* Dangling GPIO pins */
+				gpios_hrefv60_mode: gpios_hrefv60 {
+					default_cfg1 {
+						/* Normally UART1 RXD, now dangling */
+						pins = "GPIO4_AH6";
+						ste,config = <&in_pu>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/st/ste-nomadik-nhk15.dts
new file mode 100644
index 000000000000..cdff33063d6f
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-nomadik-nhk15.dts
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree for the ST Microelectronics Nomadik NHK8815 board
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "ste-nomadik-stn8815.dtsi"
+
+/ {
+	model = "Nomadik STN8815NHK";
+	compatible = "st,nomadik-nhk-15";
+
+	chosen {
+		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		stmpe-i2c0 = &stmpe0;
+		stmpe-i2c1 = &stmpe1;
+	};
+
+	pinctrl {
+		uart0 {
+			uart0_nhk_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1", "u0ctsrts_a_1";
+				};
+			};
+		};
+
+		stmpe2401_1 {
+			stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
+				nhk_cfg1 {
+					pins = "GPIO76_B20"; // IRQ line
+					ste,input = <0>;
+				};
+				nhk_cfg2 {
+					pins = "GPIO77_B8"; // reset line
+					ste,output = <1>;
+				};
+			};
+		};
+		stmpe2401_2 {
+			stmpe2401_2_nhk_mode: stmpe2401_2_nhk {
+				nhk_cfg1 {
+					pins = "GPIO78_A8"; // IRQ line
+					ste,input = <0>;
+				};
+				nhk_cfg2 {
+					pins = "GPIO79_C9"; // reset line
+					ste,output = <1>;
+				};
+			};
+		};
+		lis3lv02dl {
+			lis3lv02dl_nhk_mode: lis3lv02dl_nhk {
+				nhk_cfg1 {
+					pins = "GPIO82_C10"; // IRQ line
+					ste,input = <0>;
+				};
+			};
+		};
+	};
+	src@101e0000 {
+		/* These chrystal outputs are not used on this board */
+		disable-sxtalo;
+		disable-mxtalo;
+	};
+
+	/* This is where the interrupt is routed on the NHK-15 debug board */
+	external-bus@34000000 {
+		compatible = "simple-bus";
+		reg = <0x34000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x34000000 0x1000000>;
+		ethernet@300 {
+			compatible = "smsc,lan91c111";
+			reg = <0x300 0x0fd00>;
+			reg-io-width = <2>;
+			reset-gpios = <&stmpe_gpio44 10 GPIO_ACTIVE_HIGH>;
+			interrupt-parent = <&stmpe_gpio44>;
+			interrupts = <11 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	i2c0 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			interrupt-parent = <&gpio2>;
+			interrupts = <18 IRQ_TYPE_EDGE_RISING>; // GPIO 82
+			pinctrl-0 = <&lis3lv02dl_nhk_mode>;
+			pinctrl-names = "default";
+			reg = <0x1d>;
+		};
+		stmpe0: port-expander@43 {
+			compatible = "st,stmpe2401";
+			reg = <0x43>;
+			reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>; // GPIO77
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>; // GPIO76
+			interrupt-parent = <&gpio2>;
+			wakeup-source;
+			pinctrl-names = "default";
+			pinctrl-0 = <&stmpe2401_1_nhk_mode>;
+			stmpe_gpio43: gpio {
+				compatible = "st,stmpe-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				/* Some pins in alternate functions */
+				st,norequest-mask = <0xf0f002>;
+			};
+			keyboard-controller {
+				compatible = "st,stmpe-keypad";
+				debounce-interval = <64>;
+				st,scan-count = <8>;
+				st,no-autorepeat;
+				keypad,num-rows = <8>;
+				keypad,num-columns = <8>;
+				linux,keymap = <0x00020072 // Vol down
+						0x00030073 // Vol up
+						0x0100009e // Back
+						0x010100e3 // TV out
+						0x01020098 // Lock
+						0x0103013b // Start
+						0x020000a3 // Next
+						0x020100a4 // Play
+						0x020200a5 // Prev
+						0x02030160 // OK
+						0x03000069 // Left
+						0x0301006a // Right
+						0x03020067 // Up
+						0x0303006c>; // Down
+			};
+			stmpe0_pwm: pwm {
+				compatible = "st,stmpe-pwm";
+				#pwm-cells = <2>;
+			};
+		};
+		stmpe1: port-expander@44 {
+			compatible = "st,stmpe2401";
+			reg = <0x44>;
+			reset-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>; // GPIO79
+			interrupts = <14 IRQ_TYPE_EDGE_FALLING>; // GPIO78
+			interrupt-parent = <&gpio2>;
+			wakeup-source;
+			pinctrl-names = "default";
+			pinctrl-0 = <&stmpe2401_2_nhk_mode>;
+			stmpe_gpio44: gpio {
+				compatible = "st,stmpe-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				/*
+				 * This will turn off SATA so that MMC/SD
+				 * can thrive
+				 */
+				mmcsd-hog {
+					gpio-hog;
+					gpios = <2 0x0>;
+					output-low;
+					line-name = "SATA EN";
+				};
+			};
+		};
+	};
+
+	amba {
+		clcd@10120000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&clcd_24bit_mux>;
+			port {
+				nomadik_clcd: endpoint {
+					remote-endpoint = <&nomadik_clcd_panel>;
+					arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
+				};
+			};
+
+		};
+
+		/* Activate RX/TX and CTS/RTS on UART 0 */
+		uart0: serial@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_nhk_mode>;
+			status = "okay";
+		};
+		mmcsd: mmc@101f6000 {
+			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
+			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/*
+		 * As we're dealing with 3wire SPI, we only define SCK
+		 * and MOSI (in the spec MOSI is called "SDA").
+		 */
+		sck-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		/*
+		 * WVGA connector 21
+		 * WVGA (800x480): 4.3" TPG110 TDO43MTEA2 24-bit RGB
+		 * with TPO touch screen.
+		  */
+		panel: display@0 {
+			/*
+			 * The TPO display driver is connected to a
+			 * 5.7" OSD OSD057VA01CT TFT display.
+			 */
+			compatible = "tpo,tpg110";
+			reg = <0>;
+			spi-3wire;
+			/* 320 ns min period ~= 3 MHz */
+			spi-max-frequency = <3000000>;
+			/* Width and height from the OSD data sheet */
+			width-mm = <116>;
+			height-mm = <87>;
+			grestb-gpios = <&stmpe_gpio44 5 GPIO_ACTIVE_LOW>;
+			backlight = <&bl>;
+
+			port {
+				nomadik_clcd_panel: endpoint {
+					remote-endpoint = <&nomadik_clcd>;
+				};
+			};
+		};
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&stmpe0_pwm 0 500000>;
+		pwm-names = "backlight";
+		brightness-levels = <
+			0  1  2  3  4  5  6  7  8  9
+			10 11 12 13 14 15 16 17 18 19
+			20 21 22 23 24 25 26 27 28 29
+			30 31 32 33 34 35 36 37 38 39
+			40 41 42 43 44 45 46 47 48 49
+			50 51 52 53 54 55 56 57 58 59
+			60 61 62 63 64 65 66 67 68 69
+			70 71 72 73 74 75 76 77 78 79
+			80 81 82 83 84 85 86 87 88 89
+			90 91 92 93 94 95 96 97 98 99
+			100
+		>;
+		default-brightness-level = <100>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-nomadik-pinctrl.dtsi b/arch/arm/boot/dts/st/ste-nomadik-pinctrl.dtsi
new file mode 100644
index 000000000000..bfdb5d9a014f
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-nomadik-pinctrl.dtsi
@@ -0,0 +1,174 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson
+ */
+#include <dt-bindings/pinctrl/nomadik.h>
+
+/ {
+	in_nopull: in_nopull {
+		ste,input = <INPUT_NOPULL>;
+	};
+
+	in_pu: input_pull_up {
+		ste,input = <INPUT_PULLUP>;
+	};
+
+	in_pd: input_pull_down {
+		ste,input = <INPUT_PULLDOWN>;
+	};
+
+	out_hi: output_high {
+		ste,output = <OUTPUT_HIGH>;
+	};
+
+	out_lo: output_low {
+		ste,output = <OUTPUT_LOW>;
+	};
+
+	gpio_in_nopull: gpio_input_nopull {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,input = <INPUT_NOPULL>;
+	};
+
+	gpio_in_pu: gpio_input_pull_up {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,input = <INPUT_PULLUP>;
+	};
+
+	gpio_in_pd: gpio_input_pull_down {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,input = <INPUT_PULLDOWN>;
+	};
+
+	gpio_out_lo: gpio_output_low {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,output = <OUTPUT_LOW>;
+	};
+
+	gpio_out_hi: gpio_output_high {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,output = <OUTPUT_HIGH>;
+	};
+
+	slpm_pdis: slpm_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_wkup_pdis: slpm_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_wkup_pdis_en: slpm_wkup_pdis_en {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+	};
+
+	slpm_in_pu: slpm_in_pu {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_INPUT_PULLUP>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_in_pdis: slpm_in_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_in_wkup_pdis: slpm_in_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_in_wkup_pdis_en: slpm_in_wkup_pdis_en {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+	};
+
+	slpm_in_pu_wkup_pdis_en: slpm_in_wkup_pdis_en {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_INPUT_PULLUP>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+	};
+
+	slpm_out_lo: slpm_out_lo {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_LOW>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_out_hi: slpm_out_hi {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_out_lo_pdis: slpm_out_lo_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_LOW>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_DISABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_out_lo_wkup_pdis: slpm_out_lo_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_LOW>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_out_wkup_pdis: slpm_out_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_DIR_OUTPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	in_wkup_pdis: in_wkup_pdis {
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	in_wkup_pdis_en: in_wkup_pdis_en {
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_ENABLED>;
+	};
+
+	out_lo_wkup_pdis: out_lo_wkup_pdis {
+		ste,sleep-output = <SLPM_OUTPUT_LOW>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	out_hi_wkup_pdis: out_hi_wkup_pdis {
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	out_wkup_pdis: out_wkup_pdis {
+		ste,sleep-output = <SLPM_DIR_OUTPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-nomadik-s8815.dts b/arch/arm/boot/dts/st/ste-nomadik-s8815.dts
new file mode 100644
index 000000000000..c905c2643a12
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-nomadik-s8815.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree for the ST-Ericsson Nomadik S8815 board
+ * Produced by Calao Systems
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "ste-nomadik-stn8815.dtsi"
+
+/ {
+	model = "Calao Systems USB-S8815";
+	compatible = "calaosystems,usb-s8815";
+
+	chosen {
+		bootargs = "root=/dev/ram0 console=ttyAMA1,115200n8 earlyprintk";
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	gpio3: gpio@101e7000 {
+		/* This hog will bias the MMC/SD card detect line */
+		mmcsd-gpio {
+			gpio-hog;
+			gpios = <16 0x0>;
+			output-low;
+			line-name = "card detect bias";
+		};
+	};
+
+	src@101e0000 {
+		/* These chrystal drivers are not used on this board */
+		disable-sxtalo;
+		disable-mxtalo;
+	};
+
+	pinctrl {
+		/* Hog CD pins */
+		pinctrl-names = "default";
+		pinctrl-0 = <&cd_default_mode>;
+
+		uart0 {
+			/* Only use RX/TX pins */
+			uart0_s8815_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1";
+				};
+			};
+		};
+		mmcsd-cd {
+			cd_default_mode: cd_default {
+				cd_default_cfg1 {
+					/* CD input GPIO */
+					pins = "GPIO111_H21";
+					ste,input = <0>;
+				};
+				cd_default_cfg2 {
+					/* CD GPIO biasing */
+					pins = "GPIO112_J21";
+					ste,output = <0>;
+				};
+			};
+		};
+		gpioi2c {
+			gpioi2c_default_mode: gpioi2c_default {
+				gpioi2c_default_cfg {
+					pins = "GPIO73_C21", "GPIO74_C20";
+					ste,input = <0>;
+				};
+			};
+		};
+		user-led {
+			user_led_default_mode: user_led_default {
+				user_led_default_cfg {
+					pins = "GPIO2_C5";
+					ste,output = <1>;
+				};
+			};
+		};
+		user-button {
+			user_button_default_mode: user_button_default {
+				user_button_default_cfg {
+					pins = "GPIO3_A4";
+					ste,input = <0>;
+				};
+			};
+		};
+	};
+
+	/* Ethernet */
+	external-bus@34000000 {
+		compatible = "simple-bus";
+		reg = <0x34000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x34000000 0x1000000>;
+		ethernet@300 {
+			compatible = "smsc,lan91c111";
+			reg = <0x300 0x0fd00>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	i2c1 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			reg = <0x1d>;
+		};
+	};
+
+	/* GPIO I2C connected to the USB portions of the STw4811 only */
+	gpio-i2c {
+		compatible = "i2c-gpio";
+		gpios = <&gpio2 10 0>, /* sda */
+			<&gpio2 9 0>; /* scl */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpioi2c_default_mode>;
+
+		stw4811@2d {
+			   compatible = "st,stw4811-usb";
+			   reg = <0x2d>;
+		};
+	};
+
+
+	amba {
+		/* Activate RXTX on UART 0 */
+		uart0: serial@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_s8815_mode>;
+			status = "okay";
+		};
+		/* Configure card detect for the uSD slot */
+		mmc@101f6000 {
+			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* The user LED on the board is set up to be used for heartbeat */
+	leds {
+		compatible = "gpio-leds";
+		user-led {
+			label = "user_led";
+			gpios = <&gpio0 2 0x1>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led_default_mode>;
+		};
+	};
+
+	/* User key mapped in as "escape" */
+	gpio-keys {
+		compatible = "gpio-keys";
+		user-button {
+			label = "user_button";
+			gpios = <&gpio0 3 0x1>;
+			linux,code = <1>; /* KEY_ESC */
+			wakeup-source;
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_button_default_mode>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/st/ste-nomadik-stn8815.dtsi
new file mode 100644
index 000000000000..6816eef39d45
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-nomadik-stn8815.dtsi
@@ -0,0 +1,884 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree for the ST-Ericsson Nomadik 8815 STn8815 SoC
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x04000000>,
+		    <0x08000000 0x04000000>;
+	};
+
+	L2: cache-controller {
+		compatible = "arm,l210-cache";
+		reg = <0x10210000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <30>;
+		cache-unified;
+		cache-level = <2>;
+		cache-size = <131072>;
+		cache-sets = <512>;
+		cache-line-size = <32>;
+		/* At full speed latency must be >=2 */
+		arm,tag-latency = <8>;
+		arm,data-latency = <8 8>;
+		arm,dirty-latency = <8>;
+	};
+
+	mtu0: mtu@101e2000 {
+		/* Nomadik system timer */
+		compatible = "st,nomadik-mtu";
+		reg = <0x101e2000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <4>;
+		clocks = <&timclk>, <&pclk>;
+		clock-names = "timclk", "apb_pclk";
+	};
+
+	mtu1: mtu@101e3000 {
+		/* Secondary timer */
+		reg = <0x101e3000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <5>;
+		clocks = <&timclk>, <&pclk>;
+		clock-names = "timclk", "apb_pclk";
+	};
+
+	gpio0: gpio@101e4000 {
+		compatible = "st,nomadik-gpio";
+		reg =  <0x101e4000 0x80>;
+		interrupt-parent = <&vica>;
+		interrupts = <6>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-bank = <0>;
+		gpio-ranges = <&pinctrl 0 0 32>;
+		clocks = <&pclk>;
+	};
+
+	gpio1: gpio@101e5000 {
+		compatible = "st,nomadik-gpio";
+		reg =  <0x101e5000 0x80>;
+		interrupt-parent = <&vica>;
+		interrupts = <7>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-bank = <1>;
+		gpio-ranges = <&pinctrl 0 32 32>;
+		clocks = <&pclk>;
+	};
+
+	gpio2: gpio@101e6000 {
+		compatible = "st,nomadik-gpio";
+		reg =  <0x101e6000 0x80>;
+		interrupt-parent = <&vica>;
+		interrupts = <8>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-bank = <2>;
+		gpio-ranges = <&pinctrl 0 64 32>;
+		clocks = <&pclk>;
+	};
+
+	gpio3: gpio@101e7000 {
+		compatible = "st,nomadik-gpio";
+		reg =  <0x101e7000 0x80>;
+		ngpio = <28>;
+		interrupt-parent = <&vica>;
+		interrupts = <9>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-bank = <3>;
+		gpio-ranges = <&pinctrl 0 96 28>;
+		clocks = <&pclk>;
+	};
+
+	pinctrl: pinctrl {
+		compatible = "stericsson,stn8815-pinctrl";
+		nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>;
+		/* Pin configurations */
+		uart1 {
+			uart1_default_mux: uart1_mux {
+				u1_default_mux {
+					function = "u1";
+					groups = "u1_a_1";
+				};
+			};
+		};
+		mmcsd {
+			mmcsd_default_mux: mmcsd_mux {
+				mmcsd_default_mux {
+					function = "mmcsd";
+					groups = "mmcsd_a_1", "mmcsd_b_1";
+				};
+			};
+			mmcsd_default_mode: mmcsd_default {
+				mmcsd_default_cfg1 {
+					/*
+					 * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+					 * MCCMD, MCDAT3-0, MCMSFBCLK
+					 */
+					pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+					       "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+					       "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+					ste,output = <2>;
+				};
+			};
+		};
+		i2c0 {
+			i2c0_default_mux: i2c0_mux {
+				i2c0_default_mux {
+					function = "i2c0";
+					groups = "i2c0_a_1";
+				};
+			};
+			i2c0_default_mode: i2c0_default {
+				i2c0_default_cfg {
+					pins = "GPIO62_D3", "GPIO63_D2";
+					ste,input = <0>;
+				};
+			};
+		};
+		i2c1 {
+			i2c1_default_mux: i2c1_mux {
+				i2c1_default_mux {
+					function = "i2c1";
+					groups = "i2c1_a_1";
+				};
+			};
+			i2c1_default_mode: i2c1_default {
+				i2c1_default_cfg {
+					pins = "GPIO53_L4", "GPIO54_L3";
+					ste,input = <0>;
+				};
+			};
+		};
+		clcd {
+			/*
+			 * This should be activated to use the additional
+			 * 8 lines for bits 16 thru 23 from the CLCD block.
+			 */
+			clcd_24bit_mux: clcd_mux {
+				clcd_24bit_mux {
+					function = "clcd";
+					groups = "clcd_16_23_b_1";
+				};
+			};
+		};
+	};
+
+	/* Power Management Unit */
+	pmu: pmu@101e9000 {
+		compatible = "stericsson,nomadik-pmu", "syscon";
+		reg = <0x101e0000 0x1000>;
+	};
+
+	src: src@101e0000 {
+		compatible = "stericsson,nomadik-src";
+		reg = <0x101e0000 0x1000>;
+
+		/*
+		 * MXTAL "Main Chrystal" is a chrystal oscillator @19.2 MHz
+		 * that is parent of TIMCLK, PLL1 and PLL2
+		 */
+		mxtal: mxtal@19.2M {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19200000>;
+		};
+
+		/*
+		 * The 2.4 MHz TIMCLK reference clock is active at
+		 * boot time, this is actually the MXTALCLK @19.2 MHz
+		 * divided by 8. This clock is used by the timers and
+		 * watchdog. See page 105 ff.
+		 */
+		timclk: timclk@2.4M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <8>;
+			clock-mult = <1>;
+			clocks = <&mxtal>;
+		};
+
+		/* PLL1 is locked to MXTALI and variable from 20.4 to 334 MHz */
+		pll1: pll1@0 {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-pll-clock";
+			pll-id = <1>;
+			clocks = <&mxtal>;
+		};
+
+		/* HCLK divides the PLL1 with 1,2,3 or 4 */
+		hclk: hclk@0 {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-hclk-clock";
+			clocks = <&pll1>;
+		};
+		/* The PCLK domain uses HCLK right off */
+		pclk: pclk@0 {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <1>;
+			clock-mult = <1>;
+			clocks = <&hclk>;
+		};
+
+		/* PLL2 is usually 864 MHz and divided into a few fixed rates */
+		pll2: pll2@0 {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-pll-clock";
+			pll-id = <2>;
+			clocks = <&mxtal>;
+		};
+		clk216: clk216@216M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <4>;
+			clock-mult = <1>;
+			clocks = <&pll2>;
+		};
+		clk108: clk108@108M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <2>;
+			clock-mult = <1>;
+			clocks = <&clk216>;
+		};
+		clk72: clk72@72M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			/* The data sheet does not say how this is derived */
+			clock-div = <12>;
+			clock-mult = <1>;
+			clocks = <&pll2>;
+		};
+		clk48: clk48@48M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			/* The data sheet does not say how this is derived */
+			clock-div = <18>;
+			clock-mult = <1>;
+			clocks = <&pll2>;
+		};
+		clk27: clk27@27M {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clock-div = <4>;
+			clock-mult = <1>;
+			clocks = <&clk108>;
+		};
+
+		/* This apparently exists as well */
+		ulpiclk: ulpiclk@60M {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <60000000>;
+		};
+
+		/*
+		 * IP AMBA bus clocks, driving the bus side of the
+		 * peripheral clocking, clock gates.
+		 */
+
+		hclkdma0: hclkdma0@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <0>;
+			clocks = <&hclk>;
+		};
+		hclksmc: hclksmc@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <1>;
+			clocks = <&hclk>;
+		};
+		hclksdram: hclksdram@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <2>;
+			clocks = <&hclk>;
+		};
+		hclkdma1: hclkdma1@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <3>;
+			clocks = <&hclk>;
+		};
+		hclkclcd: hclkclcd@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <4>;
+			clocks = <&hclk>;
+		};
+		pclkirda: pclkirda@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <5>;
+			clocks = <&pclk>;
+		};
+		pclkssp: pclkssp@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <6>;
+			clocks = <&pclk>;
+		};
+		pclkuart0: pclkuart0@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <7>;
+			clocks = <&pclk>;
+		};
+		pclksdi: pclksdi@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <8>;
+			clocks = <&pclk>;
+		};
+		pclki2c0: pclki2c0@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <9>;
+			clocks = <&pclk>;
+		};
+		pclki2c1: pclki2c1@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <10>;
+			clocks = <&pclk>;
+		};
+		pclkuart1: pclkuart1@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <11>;
+			clocks = <&pclk>;
+		};
+		pclkmsp0: pclkmsp0@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <12>;
+			clocks = <&pclk>;
+		};
+		hclkusb: hclkusb@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <13>;
+			clocks = <&hclk>;
+		};
+		hclkdif: hclkdif@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <14>;
+			clocks = <&hclk>;
+		};
+		hclksaa: hclksaa@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <15>;
+			clocks = <&hclk>;
+		};
+		hclksva: hclksva@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <16>;
+			clocks = <&hclk>;
+		};
+		pclkhsi: pclkhsi@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <17>;
+			clocks = <&pclk>;
+		};
+		pclkxti: pclkxti@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <18>;
+			clocks = <&pclk>;
+		};
+		pclkuart2: pclkuart2@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <19>;
+			clocks = <&pclk>;
+		};
+		pclkmsp1: pclkmsp1@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <20>;
+			clocks = <&pclk>;
+		};
+		pclkmsp2: pclkmsp2@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <21>;
+			clocks = <&pclk>;
+		};
+		pclkowm: pclkowm@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <22>;
+			clocks = <&pclk>;
+		};
+		hclkhpi: hclkhpi@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <23>;
+			clocks = <&hclk>;
+		};
+		pclkske: pclkske@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <24>;
+			clocks = <&pclk>;
+		};
+		pclkhsem: pclkhsem@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <25>;
+			clocks = <&pclk>;
+		};
+		hclk3d: hclk3d@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <26>;
+			clocks = <&hclk>;
+		};
+		hclkhash: hclkhash@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <27>;
+			clocks = <&hclk>;
+		};
+		hclkcryp: hclkcryp@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <28>;
+			clocks = <&hclk>;
+		};
+		pclkmshc: pclkmshc@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <29>;
+			clocks = <&pclk>;
+		};
+		hclkusbm: hclkusbm@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <30>;
+			clocks = <&hclk>;
+		};
+		hclkrng: hclkrng@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <31>;
+			clocks = <&hclk>;
+		};
+
+		/* IP kernel clocks */
+		clcdclk: clcdclk@0 {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <36>;
+			clocks = <&clk72 &clk48>;
+		};
+		irdaclk: irdaclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <37>;
+			clocks = <&clk48>;
+		};
+		sspiclk: sspiclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <38>;
+			clocks = <&clk48>;
+		};
+		uart0clk: uart0clk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <39>;
+			clocks = <&clk48>;
+		};
+		sdiclk: sdiclk@48M {
+			/* Also called MCCLK in some documents */
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <40>;
+			clocks = <&clk48>;
+		};
+		i2c0clk: i2c0clk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <41>;
+			clocks = <&clk48>;
+		};
+		i2c1clk: i2c1clk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <42>;
+			clocks = <&clk48>;
+		};
+		uart1clk: uart1clk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <43>;
+			clocks = <&clk48>;
+		};
+		mspclk0: mspclk0@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <44>;
+			clocks = <&clk48>;
+		};
+		usbclk: usbclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <45>;
+			clocks = <&clk48>; /* 48 MHz not ULPI */
+		};
+		difclk: difclk@72M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <46>;
+			clocks = <&clk72>;
+		};
+		ipi2cclk: ipi2cclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <47>;
+			clocks = <&clk48>; /* Guess */
+		};
+		ipbmcclk: ipbmcclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <48>;
+			clocks = <&clk48>; /* Guess */
+		};
+		hsiclkrx: hsiclkrx@216M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <49>;
+			clocks = <&clk216>;
+		};
+		hsiclktx: hsiclktx@108M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <50>;
+			clocks = <&clk108>;
+		};
+		uart2clk: uart2clk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <51>;
+			clocks = <&clk48>;
+		};
+		mspclk1: mspclk1@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <52>;
+			clocks = <&clk48>;
+		};
+		mspclk2: mspclk2@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <53>;
+			clocks = <&clk48>;
+		};
+		owmclk: owmclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <54>;
+			clocks = <&clk48>; /* Guess */
+		};
+		skeclk: skeclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <56>;
+			clocks = <&clk48>; /* Guess */
+		};
+		x3dclk: x3dclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <58>;
+			clocks = <&clk48>; /* Guess */
+		};
+		pclkmsp3: pclkmsp3@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <59>;
+			clocks = <&pclk>;
+		};
+		mspclk3: mspclk3@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <60>;
+			clocks = <&clk48>;
+		};
+		mshcclk: mshcclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <61>;
+			clocks = <&clk48>; /* Guess */
+		};
+		usbmclk: usbmclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <62>;
+			/* Stated as "48 MHz not ULPI clock" */
+			clocks = <&clk48>;
+		};
+		rngcclk: rngcclk@48M {
+			#clock-cells = <0>;
+			compatible = "st,nomadik-src-clock";
+			clock-id = <63>;
+			clocks = <&clk48>; /* Guess */
+		};
+	};
+
+	/* A NAND flash of 128 MiB */
+	fsmc: flash@40000000 {
+		compatible = "stericsson,fsmc-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x10100000 0x1000>,	/* FSMC Register*/
+			<0x40000000 0x2000>,	/* NAND Base DATA */
+			<0x41000000 0x2000>,	/* NAND Base ADDR */
+			<0x40800000 0x2000>;	/* NAND Base CMD */
+		reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
+		clocks = <&hclksmc>;
+		status = "okay";
+
+		partition@0 {
+		label = "X-Loader(NAND)";
+			reg = <0x0 0x40000>;
+		};
+		partition@40000 {
+			label = "MemInit(NAND)";
+			reg = <0x40000 0x40000>;
+		};
+		partition@80000 {
+			label = "BootLoader(NAND)";
+			reg = <0x80000 0x200000>;
+		};
+		partition@280000 {
+			label = "Kernel zImage(NAND)";
+			reg = <0x280000 0x300000>;
+		};
+		partition@580000 {
+			label = "Root Filesystem(NAND)";
+			reg = <0x580000 0x1600000>;
+		};
+		partition@1b80000 {
+			label = "User Filesystem(NAND)";
+			reg = <0x1b80000 0x6480000>;
+		};
+	};
+
+	/* I2C0 connected to the STw4811 power management chip */
+	i2c0 {
+		compatible = "st,nomadik-i2c", "arm,primecell";
+		reg = <0x101f8000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <20>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&i2c0clk>, <&pclki2c0>;
+		clock-names = "mclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_default_mux>, <&i2c0_default_mode>;
+
+		stw4811@2d {
+			compatible = "st,stw4811";
+			reg = <0x2d>;
+			vmmc_regulator: vmmc {
+				compatible = "st,stw481x-vmmc";
+				regulator-name = "VMMC";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	/* I2C1 connected to various sensors */
+	i2c1 {
+		compatible = "st,nomadik-i2c", "arm,primecell";
+		reg = <0x101f7000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <21>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&i2c1clk>, <&pclki2c1>;
+		clock-names = "mclk", "apb_pclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_default_mux>, <&i2c1_default_mode>;
+
+		camera@2d {
+			   compatible = "st,camera";
+			   reg = <0x10>;
+		};
+		stw5095@1a {
+			   compatible = "st,stw5095";
+			   reg = <0x1a>;
+		};
+	};
+
+	amba {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		clcd@10120000 {
+			compatible = "arm,pl110", "arm,primecell";
+			reg = <0x10120000 0x1000>;
+			interrupt-names = "combined";
+			interrupts = <14>;
+			interrupt-parent = <&vica>;
+			clocks = <&clcdclk>, <&hclkclcd>;
+			clock-names = "clcdclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		vica: interrupt-controller@10140000 {
+			compatible = "arm,versatile-vic";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x10140000 0x20>;
+		};
+
+		vicb: interrupt-controller@10140020 {
+			compatible = "arm,versatile-vic";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			reg = <0x10140020 0x20>;
+		};
+
+		uart0: serial@101fd000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x101fd000 0x1000>;
+			interrupt-parent = <&vica>;
+			interrupts = <12>;
+			clocks = <&uart0clk>, <&pclkuart0>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+			dmas = <&dmac0 14 1>,
+			       <&dmac0 15 1>;
+			dma-names = "rx", "tx";
+		};
+
+		uart1: serial@101fb000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x101fb000 0x1000>;
+			interrupt-parent = <&vica>;
+			interrupts = <17>;
+			clocks = <&uart1clk>, <&pclkuart1>;
+			clock-names = "uartclk", "apb_pclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_default_mux>;
+			dmas = <&dmac1 22 1>,
+			       <&dmac1 23 1>;
+			dma-names = "rx", "tx";
+		};
+
+		uart2: serial@101f2000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x101f2000 0x1000>;
+			interrupt-parent = <&vica>;
+			interrupts = <28>;
+			clocks = <&uart2clk>, <&pclkuart2>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+			dmas = <&dmac1 30 1>,
+			       <&dmac1 31 1>;
+			dma-names = "rx", "tx";
+		};
+
+		rng: rng@101b0000 {
+			compatible = "arm,primecell";
+			reg = <0x101b0000 0x1000>;
+			clocks = <&rngcclk>, <&hclkrng>;
+			clock-names = "rng", "apb_pclk";
+		};
+
+		rtc: rtc@101e8000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0x101e8000 0x1000>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+			interrupt-parent = <&vica>;
+			interrupts = <10>;
+		};
+
+		mmcsd: mmc@101f6000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x101f6000 0x1000>;
+			clocks = <&sdiclk>, <&pclksdi>;
+			clock-names = "mclk", "apb_pclk";
+			interrupt-parent = <&vica>;
+			interrupts = <22>;
+			max-frequency = <400000>;
+			bus-width = <4>;
+			cap-mmc-highspeed;
+			cap-sd-highspeed;
+			full-pwr-cycle;
+			/*
+			 * The STw4811 circuit used with the Nomadik strictly
+			 * requires that all of these signal direction pins be
+			 * routed and used for its 4-bit levelshifter.
+			 */
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-dir-dat31;
+			st,sig-dir-cmd;
+			st,sig-pin-fbclk;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
+			vmmc-supply = <&vmmc_regulator>;
+		};
+
+		dmac0: dma-controller@10130000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0x10130000 0x1000>;
+			interrupt-parent = <&vica>;
+			interrupts = <15>;
+			clocks = <&hclkdma0>;
+			clock-names = "apb_pclk";
+			lli-bus-interface-ahb1;
+			lli-bus-interface-ahb2;
+			mem-bus-interface-ahb2;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			#dma-cells = <2>;
+		};
+		dmac1: dma-controller@10150000 {
+			compatible = "arm,pl080", "arm,primecell";
+			reg = <0x10150000 0x1000>;
+			interrupt-parent = <&vica>;
+			interrupts = <13>;
+			clocks = <&hclkdma1>;
+			clock-names = "apb_pclk";
+			lli-bus-interface-ahb1;
+			lli-bus-interface-ahb2;
+			mem-bus-interface-ahb2;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			#dma-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-snowball.dts b/arch/arm/boot/dts/st/ste-snowball.dts
new file mode 100644
index 000000000000..9a3d6546399d
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-snowball.dts
@@ -0,0 +1,657 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2011 ST-Ericsson AB
+ */
+
+/dts-v1/;
+#include "ste-db9500.dtsi"
+#include "ste-href-ab8500.dtsi"
+#include "ste-href-family-pinctrl.dtsi"
+
+/ {
+	model = "Calao Systems Snowball platform with device tree";
+	compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+		battery-type = "lithium-ion-polymer";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	en_3v3_reg: en_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "en-3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
+		gpio = <&ab8500_gpio 25 0x4>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@1 {
+			debounce-interval = <50>;
+			wakeup-source;
+			linux,code = <2>;
+			label = "userpb";
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		};
+		button@2 {
+			debounce-interval = <50>;
+			wakeup-source;
+			linux,code = <3>;
+			label = "extkb1";
+			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+		};
+		button@3 {
+			debounce-interval = <50>;
+			wakeup-source;
+			linux,code = <4>;
+			label = "extkb2";
+			gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+		};
+		button@4 {
+			debounce-interval = <50>;
+			wakeup-source;
+			linux,code = <5>;
+			label = "extkb3";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		};
+		button@5 {
+			debounce-interval = <50>;
+			wakeup-source;
+			linux,code = <6>;
+			label = "extkb4";
+			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpioled_snowball_mode>;
+		used-led {
+			label = "user_led";
+			gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	soc {
+		/* Name the GPIO muxed rails on the Snowball board */
+		gpio@8012e000 {
+			/* GPIOs 0 - 31 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "",
+				     "AP_GPIO31";
+		};
+
+		gpio@8012e080 {
+			/* GPIOs 32 - 63 */
+			gpio-line-names = "USR PB", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e000 {
+			/* GPIOs 64 - 95 */
+			gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e100 {
+			/* GPIOs 128 - 159 */
+			gpio-line-names = "", "", "", "", "", "", "", "",
+				     "", "", "", "", "IRQ_LAN", "RSTn_LAN",
+				     "USR_LED", "", "", "", "", "", "",
+				     "", "", "AP_GPIO151", "AP_GPIO152",
+				     "", "", "", "", "", "", "";
+		};
+
+		gpio@8000e180 {
+			/* GPIOs 160 - 191 */
+			gpio-line-names = "", "AP_GPIO161", "AP_GPIO162",
+				     "ACCELEROMETER_INT1_RDY",
+				     "ACCELEROMETER_INT2", "MAG_DRDY",
+				     "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC",
+				     "GYRO_INT", "UART_WAKE", "GBF_RESET",
+				     "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		gpio@8011e000 {
+			/* GPIOs 192 - 223 */
+			gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST",
+				     "", "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "", "",
+				     "WLAN_RESETN", "WLAN_IRQ", "MMC_EN",
+				     "MMC_CD", "", "", "", "", "";
+		};
+
+		gpio@8011e080 {
+			/* GPIOs 224 - 255 */
+			gpio-line-names = "", "", "", "", "SD_SEL", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "",
+				     "", "", "", "", "", "", "", "";
+		};
+
+		msp0: msp@80123000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp0txrxtfstck_a_1_default>;
+			status = "okay";
+		};
+
+		msp1: msp@80124000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp1txrx_a_1_default>;
+			status = "okay";
+		};
+
+		msp2: msp@80117000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&msp2_a_1_default>;
+		};
+
+		msp3: msp@80125000 {
+			status = "okay";
+		};
+
+		external-bus@50000000 {
+			status = "okay";
+
+			ethernet@0 {
+				compatible = "smsc,lan9115";
+				reg = <0 0x10000>;
+				interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+				interrupt-parent = <&gpio4>;
+				vdd33a-supply = <&en_3v3_reg>;
+				vddvario-supply = <&db8500_vape_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&eth_snowball_mode>;
+
+				reg-shift = <1>;
+				reg-io-width = <2>;
+				smsc,force-internal-phy;
+				smsc,irq-active-high;
+				smsc,irq-push-pull;
+
+				clocks = <&prcc_pclk 3 0>;
+			};
+		};
+
+		/* ST6G3244ME level translator for 1.8/2.9 V */
+		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
+			/* GPIO228 SD_SEL */
+			gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+			/* GPIO217 MMC_EN */
+			enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2900000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			startup-delay-us = <100>;
+
+			states = <1800000 0x1
+				  2900000 0x0>;
+		};
+
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			/* All direction control is used */
+			st,sig-dir-cmd;
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-dir-dat31;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&vmmci>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+
+			/* GPIO218 MMC_CD */
+			cd-gpios  = <&gpio6 26 GPIO_ACTIVE_LOW>;
+
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_1_default>;
+			pinctrl-1 = <&mc1_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		// Unused PoP eMMC - register and put it to sleep by default */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		// On-board eMMC
+		mmc@80114000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			cap-mmc-highspeed;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ab8500_ldo_aux2_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc4_a_1_default>;
+			pinctrl-1 = <&mc4_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* This UART is unused and thus left disabled */
+		serial@80121000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+		};
+
+		serial@80007000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+			status = "okay";
+		};
+
+		i2c@80004000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+			status = "okay";
+		};
+
+		i2c@80122000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+			status = "okay";
+		};
+
+		i2c@80128000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+			status = "okay";
+			lsm303dlh@18 {
+				/* Accelerometer */
+				compatible = "st,lsm303dlh-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x18>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&accel_snowball_mode>;
+				interrupt-parent = <&gpio5>;
+				interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
+					     <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
+			};
+			lsm303dlh@1e {
+				/* Magnetometer */
+				compatible = "st,lsm303dlh-magn";
+				reg = <0x1e>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&magneto_snowball_mode>;
+				interrupt-parent = <&gpio5>;
+				interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
+			};
+			l3g4200d@68 {
+				/* Gyroscope */
+				compatible = "st,l3g4200d-gyro";
+				st,drdy-int-pin = <2>;
+				reg = <0x68>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gyro_snowball_mode>;
+				interrupt-parent = <&gpio5>;
+				interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
+					     <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
+			};
+			lsp001wm@5c {
+				/* Barometer/pressure sensor */
+				compatible = "st,lps001wp-press";
+				reg = <0x5c>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&db8500_vsmps2_reg>;
+			};
+		};
+
+		i2c@80110000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+			status = "okay";
+		};
+
+		spi@80002000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&ssp0_snowball_mode>;
+			status = "okay";
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				gpio {
+					/*
+					 * AB8500 GPIOs are numbered starting from 1, so the first
+					 * index 0 is what in the datasheet is called "GPIO1", and
+					 * the second is "GPIO2" and so forth. Confusingly, the
+					 * Snowball schematic then names the "GPIO2" line "PM_GPIO1".
+					 * while later naming "GPIO4" as "PM_GPIO4".
+					 */
+					gpio-line-names = "", /* AB8500 GPIO1 */
+						     "PM_GPIO1", /* AB8500 GPIO2 */
+						     "WLAN_CLK_REQ", /* AB8500 GPIO3 */
+						     "PM_GPIO4", /* AB8500 GPIO4 */
+						     "", "", "", "", "", "", "", "", "", "", "",
+						     "EN_3V6", /* AB8500 GPIO16 */
+						     "", "", "", "" ,"", "", "", "", "",
+						     "EN_3V3", /* AB8500 GPIO26 */
+						     "", "", "", "", "", "", "", "", "", "", "", "", "",
+						     "PM_GPIO40", /* AB8500 GPIO40 */
+						     "PM_GPIO41", /* AB8500 GPIO41 */
+						     "PM_GPIO42"; /* AB8500 GPIO42 */
+				};
+
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ext_regulators: regulator-external {
+					ab8500_ext1_reg: ab8500_ext1 {
+						regulator-name = "ab8500-ext-supply1";
+					};
+
+					ab8500_ext2_reg_reg: ab8500_ext2 {
+						regulator-name = "ab8500-ext-supply2";
+					};
+
+					ab8500_ext3_reg_reg: ab8500_ext3 {
+						regulator-name = "ab8500-ext-supply3";
+					};
+				};
+
+				regulator {
+					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
+						regulator-name = "V-DISPLAY";
+					};
+
+					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
+						regulator-name = "V-eMMC1";
+					};
+
+					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
+						regulator-name = "V-MMC-SD";
+					};
+
+					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
+						regulator-name = "V-INTCORE";
+					};
+
+					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
+						regulator-name = "V-TVOUT";
+					};
+
+					ab8500_ldo_audio_reg: ab8500_ldo_audio {
+						regulator-name = "V-AUD";
+					};
+
+					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
+						regulator-name = "V-AMIC1";
+					};
+
+					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
+						regulator-name = "V-AMIC2";
+					};
+
+					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
+						regulator-name = "V-DMIC";
+					};
+
+					ab8500_ldo_ana_reg: ab8500_ldo_ana {
+						regulator-name = "V-CSI/DSI";
+					};
+				};
+			};
+		};
+
+		pinctrl {
+			/*
+			 * Set this up using hogs, as time goes by and as seems fit, these
+			 * can be moved over to being controlled by respective device.
+			 */
+			pinctrl-names = "default";
+			pinctrl-0 = <&gbf_snowball_mode>,
+				  <&wlan_snowball_mode>;
+
+			ethernet {
+				/*
+				 * Mux in "SM" which is used for the
+				 * SMSC911x Ethernet adapter
+				 */
+				eth_snowball_mode: eth_snowball {
+					snowball_mux {
+						function = "sm";
+						groups = "sm_b_1";
+					};
+					/* LAN IRQ pin */
+					snowball_cfg1 {
+						pins = "GPIO140_B11";
+						ste,config = <&in_nopull>;
+					};
+					/* LAN reset pin */
+					snowball_cfg2 {
+						pins = "GPIO141_C12";
+						ste,config = <&gpio_out_hi>;
+					};
+
+				};
+			};
+			sdi0 {
+				sdi0_default_mode: sdi0_default {
+					snowball_mux {
+						function = "mc0";
+						/* Add the DAT31 pin even if it is not really used */
+						groups = "mc0dat31dir_a_1";
+					};
+					snowball_cfg1 {
+						pins = "GPIO21_AB3"; /* DAT31DIR */
+						ste,config = <&out_hi>;
+					};
+					/* SD card detect GPIO pin, extend default state */
+					snowball_cfg2 {
+						pins = "GPIO218_AH11";
+						ste,config = <&gpio_in_pu>;
+					};
+					/* VMMCI level-shifter enable */
+					snowball_cfg3 {
+						pins = "GPIO217_AH12";
+						ste,config = <&gpio_out_hi>;
+					};
+					/* VMMCI level-shifter voltage select */
+					snowball_cfg4 {
+						pins = "GPIO228_AJ6";
+						ste,config = <&gpio_out_hi>;
+					};
+				};
+			};
+			ssp0 {
+				ssp0_snowball_mode: ssp0_snowball_default {
+					snowball_mux {
+						function = "ssp0";
+						groups = "ssp0_a_1";
+					};
+					snowball_cfg1 {
+						pins = "GPIO144_B13"; /* FRM */
+						ste,config = <&gpio_out_hi>;
+					};
+					snowball_cfg2 {
+						pins = "GPIO145_C13"; /* RXD */
+						ste,config = <&in_pd>;
+					};
+					snowball_cfg3 {
+						pins =
+						"GPIO146_D13", /* TXD */
+						"GPIO143_D12"; /* CLK */
+						ste,config = <&out_lo>;
+					};
+
+				};
+			};
+			gpio_led {
+				gpioled_snowball_mode: gpioled_default {
+					snowball_cfg1 {
+						pins = "GPIO142_C11";
+						ste,config = <&gpio_out_hi>;
+					};
+
+				};
+			};
+			accelerometer {
+				accel_snowball_mode: accel_snowball {
+					/* Accelerometer lines */
+					snowball_cfg1 {
+						pins =
+						"GPIO163_C20", /* ACCEL_IRQ1 */
+						"GPIO164_B21"; /* ACCEL_IRQ2 */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			gyro {
+				gyro_snowball_mode: gyro_snowball {
+					snowball_cfg1 {
+						pins =
+						"GPIO166_A22", /* DRDY */
+						"GPIO169_D22"; /* INT */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			magnetometer {
+				magneto_snowball_mode: magneto_snowball {
+					snowball_cfg1 {
+						pins = "GPIO165_C21"; /* MAG_DRDY */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+			gbf {
+				gbf_snowball_mode: gbf_snowball {
+					/*
+					 * GBF (GPS, Bluetooth, FM-radio) interface,
+					 * pull low to reset state
+					 */
+					snowball_cfg1 {
+						pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+						ste,config = <&gpio_out_lo>;
+					};
+				 };
+			};
+			wlan {
+				wlan_snowball_mode: wlan_snowball {
+					/*
+					 * Activate this mode with the WLAN chip.
+					 * These are plain GPIO pins used by WLAN
+					 */
+					snowball_cfg1 {
+						pins =
+						"GPIO161_D21", /* WLAN_PMU_EN */
+						"GPIO215_AH13"; /* WLAN_ENA */
+						ste,config = <&gpio_out_lo>;
+					};
+					snowball_cfg2 {
+						pins = "GPIO216_AG12"; /* WLAN_IRQ */
+						ste,config = <&gpio_in_pu>;
+					};
+				};
+			};
+		};
+
+		mcde@a0350000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&lcd_default_mode>;
+			pinctrl-1 = <&lcd_sleep_mode>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts
new file mode 100644
index 000000000000..463942ae755e
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-codina-tmo.dts
@@ -0,0 +1,793 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
+ * the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
+ * for T-Mobile in the United States.
+ *
+ * This phone is closely related to the Codina, but has:
+ * - No CPU speed cap, full ~1GHz rate
+ * - Different power management IC, AB8505
+ * - As AB8505 has a micro USB phy, no TI TSU6111
+ * - Different power routing such as the removal of the external LDO for the
+ *   touchscreen in favor of using the AB8505
+ * - Using a regulator for the key backlight LED
+ * - Using the Samsung S6D27A1 panel by default
+ * - The panel is using one of the ordinary AB8505 regulators for 1.8V
+ * - WiFi/Bluetooth combi chip upgraded to BCM4334
+ * - GPIO for backlight control moved from 68 to 69
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Exhibit (SGH-T599)";
+	compatible = "samsung,codina-tmo", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both the 3.0V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3.0V";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 "MOT_EN" */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	led-touchkeys {
+		compatible = "regulator-led";
+		vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
+		default-state = "on";
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		color = <LED_COLOR_ID_WHITE>;
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO69 is used on Codina R0.4 and Codina TMO */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd253_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* TODO: this should also be used by the SM5103 Camera power management unit */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			clock-frequency = <400000>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO201 */
+		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6d27a1";
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&ab8500_ldo_aux6_reg>;
+
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
+			interrupt-parent = <&gpio2>;
+			interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd253>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			/*
+			 * GPIO130 will be set to input no pull-up resulting in a resistor
+			 * pulling the reset high and taking the memory out of reset.
+			 */
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to AB8505 */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				/* This is mostly identical to the Codina v0.4 regulators */
+				regulator {
+					ab8500_ldo_aux1 {
+						regulator-name = "v-sensors-vdd";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						regulator-name = "v-aux2";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						regulator-name = "v-mmc-sd";
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "v-aux4";
+						/*
+						 * Providing some span here makes the touchkey
+						 * LEDs actually dimmable.
+						 */
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "v-aux5";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						/* 1.8 V to the display */
+						regulator-name = "v-aux6";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						regulator-name = "v-sensors-vio";
+					};
+				};
+			};
+		};
+
+		/* I2C0 also known as "AGC I2C" */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@39 {
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+
+				/* IRQ on GPIO146 "PS_INT" */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tmd2672_codina_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			/* Bosch BMA254 accelerometer */
+			accelerometer@18 {
+				compatible = "bosch,bma254";
+				reg = <0x18>;
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "1";
+				vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* TODO: write bindings and driver for this touchscreen */
+
+			/* Zinitix BT404 ISP part */
+			isp@50 {
+				compatible = "zinitix,bt404-isp";
+				reg = <0x50>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+
+			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
+			touchscreen@20 {
+				compatible = "zinitix,bt404";
+				reg = <0x20>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
+				vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
+				zinitix,mode = <2>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	sdi2 {
+		/*
+		 * GPIO130 should be set in GPIO mode and
+		 * pulled down. (Not connected.)
+		 */
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			codina_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			codina_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIOs for panel control */
+	panel {
+		panel_default_mode: panel_default {
+			codina_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+			codina_cfg2 {
+				/* ESD IRQ line "LCD detect" */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			codina_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			codina_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Backlight GPIO */
+	backlight {
+		ktd253_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			codina_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Zinitix BT404 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			codina_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor TMD2672 */
+	tmd2672 {
+		tmd2672_codina_default: tmd2672_codina {
+			codina_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for subpmu */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			codina_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			codina_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			codina_cfg2 {
+				pins = "GPIO225_AG8";
+				/* Needs pull down, no pull down resistor on board */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24",
+				       "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			codina_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			codina_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			codina_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
new file mode 100644
index 000000000000..c1ae0e23fe45
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-codina.dts
@@ -0,0 +1,953 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Ace 2 GT-I8160 also known as Codina.
+ *
+ * NOTE: this is the most common variant according to the vendor tree, known
+ * as "R0.0". There appears to be a "R0.4" variant with backlight on GPIO69,
+ * AB8505 and other changes. There is also talk about some variants having a
+ * Samsung S6D27A1 display, indicated by passing a different command line from
+ * the boot loader.
+ *
+ * The Samsung tree further talks about GT-I8160P and GT-I8160chn (China).
+ * The GT-I8160 plain is known as the "europe" variant.
+ * The GT-I8160P is the CDMA version and it appears to not use the ST
+ * Microelectronics accelerometer and reportedly has NFC mounted.
+ * The GT-I8160chn appears to be the same as the europe variant.
+ *
+ * There is also the Codina-TMO, Samsung SGH-T599, which has its own device
+ * tree.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Ace 2 (GT-I8160)";
+	compatible = "samsung,codina", "st-ericsson,u8500";
+
+	cpus {
+		cpu@300 {
+			/*
+			 * This has a frequency cap at ~800 MHz in the firmware.
+			 * (Changing this number here will not overclock it.)
+			 */
+			operating-points = <798720 0
+					    399360 0
+					    199680 0>;
+		};
+	};
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3.0V";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 "MOT_EN" */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_leds_default_mode>;
+		touchkey-led {
+			label = "touchkeys";
+			/*
+			 * GPIO194 on R0.0, R0.4 does not use this at all, it
+			 * will instead turn LDO AUX4 on/off for key led backlighy.
+			 * (Line is pulled down on R0.4)
+			 */
+			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/*
+		 * GPIO68 is for R0.0, the board file talks about a TMO variant
+		 * (R0.4) using GPIO69.
+		 */
+		enable-gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd253_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			clock-frequency = <400000>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			dvdd-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+		};
+		/* TODO: this should also be used by the SM5103 Camera power management unit */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nfc@2b {
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn544_codina_default>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO201 */
+		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/*
+		 * Some Codinas (90%) have a WideChips WS2401-based LMS380KF01
+		 * display mounted and some 10% has a Samsung S6D27A1 instead.
+		 * The boot loader needs to modify this compatible to
+		 * correspond to whatever is passed from the early Samsung boot.
+		 */
+		panel@0 {
+			compatible = "samsung,lms380kf01";
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&lcd_1v8_reg>;
+
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
+			interrupt-parent = <&gpio2>;
+			interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd253>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				/* Actually BRCM4330 */
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			/*
+			 * GPIO130 will be set to input no pull-up resulting in a resistor
+			 * pulling the reset high and taking the memory out of reset.
+			 */
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				compatible = "brcm,bcm4751";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				enable-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bcm4751_codina_default>;
+			};
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 also known as "AGC I2C" */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@39 {
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+
+				/* IRQ on GPIO146 "PS_INT" */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				/* FIXME: needs a VDDIO supply that is connected to a pull-up resistor */
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tms2672_codina_default>;
+			};
+		};
+
+		/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
+		i2c@80122000 {
+			status = "okay";
+			pinctrl-names = "default","sleep";
+			/* FIXME: If it doesn't work try what we use on Gavini */
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_codina_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			lisd3dh@19 {
+				/* ST Microelectronics Accelerometer */
+				compatible = "st,lis3dh-accel";
+				st,drdy-int-pin = <1>;
+				reg = <0x19>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "1";
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* TODO: write bindings and driver for this touchscreen */
+
+			/* Zinitix BT404 ISP part */
+			isp@50 {
+				compatible = "zinitix,bt404-isp";
+				reg = <0x50>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+
+			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
+			touchscreen@20 {
+				compatible = "zinitix,bt404";
+				reg = <0x20>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				vcca-supply = <&ldo_tsp_3v3_reg>;
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				zinitix,mode = <2>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	sdi2 {
+		/*
+		 * This will make the resistor mounted in R0.0 pull up
+		 * the reset line and take the eMMC out of reset. On
+		 * R0.4 variants, GPIO130 should be set in GPIO mode and
+		 * pulled down. (Not connected.)
+		 */
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			codina_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			codina_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIOs for panel control */
+	panel {
+		panel_default_mode: panel_default {
+			codina_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+			codina_cfg2 {
+				/* ESD IRQ line "LCD detect" */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			gavini_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			codina_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	key-led {
+		gpio_leds_default_mode: en_led_ldo_default {
+			/* EN_LED_LDO on GPIO194 */
+			codina_cfg1 {
+				pins = "GPIO194_AF27";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			codina_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Backlight GPIO */
+	backlight {
+		ktd253_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO68_E1"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			codina_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Zinitix BT404 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			codina_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor TMS2672 */
+	tms2672 {
+		tms2672_codina_default: tms2672_codina {
+			codina_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for subpmu */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			codina_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			codina_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			codina_cfg2 {
+				pins = "GPIO225_AG8";
+				/* Needs pull down, no pull down resistor on board */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24",
+				       "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			codina_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			codina_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_codina_default: tsu6111_codina {
+			codina_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	nfc {
+		pn544_codina_default: pn544_codina {
+			/* Interrupt line */
+			codina_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			codina_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bcm4751 {
+		bcm4751_codina_default: bcm4751_codina {
+			/* Reset line, start out asserted */
+			codina_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			codina_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			codina_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
new file mode 100644
index 000000000000..b21e40da3dfd
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-gavini.dts
@@ -0,0 +1,887 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Beam GT-I8530 also known as Gavini.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Beam (GT-I8530)";
+	compatible = "samsung,gavini", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb585157lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO193 EN */
+		gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-projector {
+			linux,code = <KEY_SWITCHVIDEOMODE>;
+			label = "Projector";
+			/* GPIO32 "Projector On HotKey" */
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_leds_default_mode>;
+		used-led {
+			label = "touchkeys";
+			/* GPIO68 */
+			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	ktd259: backlight {
+		compatible = "kinetic,ktd259";
+		/* GPIO20 */
+		enable-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd259_backlight_default_mode>;
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas530_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * TODO: See if we can use the PL023 for this instead.
+	 */
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,lms397kf04";
+			/* 300 ns at read cycle -> 3 MHz max speed */
+			//spi-max-frequency = <3000000>;
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd259>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "MPR_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the DPP2601 projector I2C device 0x1b here */
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			/* "flash detect" actually card detect */
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>;
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <43000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			/* FIXME: fix the proximity sensor bindings and driver */
+			proximity@39 {
+				/* Gavini has the GP2A030S00F proximity sensor */
+				compatible = "sharp,gp2a030s00f";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+				/* FIXME: GPIO146 provides power on, IR LED? */
+			};
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				mount-matrix = "0", "1", "0",
+					       "1", "0", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222E accelerometer */
+					accelerometer@18 {
+						compatible = "bosch,bma222e";
+						reg = <0x18>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C2 "AGC I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_1_default>;
+			pinctrl-1 = <&i2c2_b_1_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_default>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Melfas MMS136 touchscreen */
+			touchscreen@48 {
+				compatible = "melfas,mms136";
+				reg = <0x48>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* AVDD is "analog supply", 2.57-3.47 V */
+				avdd-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			gavini_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			gavini_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			gavini_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS530 magnetometer */
+	yas530 {
+		yas530_default: yas530_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	gpio-leds {
+		gpio_leds_default_mode: gpio_leds_default {
+			/* EN_LED_LDO on GPIO68 */
+			gavini_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	backlight {
+		ktd259_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO20_AB4"; /* LCD_BL_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			gavini_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			gavini_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			gavini_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			gavini_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			gavini_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO193 */
+			skomer_cfg1 {
+				pins = "GPIO193_AH27";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO32_V2", /* Projector On HotKey */
+				       "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			gavini_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_default: mpu3050 {
+			gavini_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			gavini_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			gavini_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the TI DPP2601 */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			gavini_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			gavini_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9",
+				     "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+			gavini_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			gavini_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			gavini_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			gavini_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_default: tsu6111 {
+			gavini_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts
new file mode 100644
index 000000000000..f736888474e7
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-golden.dts
@@ -0,0 +1,733 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/*
+ * Note: This device tree cannot be booted directly with the Samsung bootloader.
+ * You need an intermediate, device-tree compatible bootloader
+ * that locks the L2 cache. Otherwise the kernel will crash after decompression.
+ *
+ * There is a port of (mainline) U-Boot, see
+ * https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500#U-Boot
+ */
+/ {
+	model = "Samsung Galaxy S III mini (GT-I8190)";
+	compatible = "samsung,golden", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb-l1m7flu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio2 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&ab8500_ldo_aux4_reg>;
+			vcc-supply = <&ab8500_ldo_aux6_reg>;
+
+			interrupt-parent = <&gpio2>;
+			interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_default>;
+			linux,keycodes = <KEY_MENU KEY_BACK>;
+		};
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux8_reg>;
+		};
+	};
+
+	soc {
+		/* External Micro SD card slot */
+		mmc@80126000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+
+			non-removable;
+			/*
+			 * Unfortunately, there is no way to enable the UHS
+			 * modes due to a limitation of the SD level translator:
+			 * It will either translate to 2.9V or disconnect the
+			 * DATA lines, so switching to 1.8V signal voltage fails.
+			 */
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+		};
+
+		/* WLAN SDIO */
+		mmc@80118000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+
+			non-removable;
+			cap-sd-highspeed;
+
+			vmmc-supply = <&wl_reg_on>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+
+				/* GPIO216 (WLAN_HOST_WAKE) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			status = "okay";
+
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+
+			vmmc-supply = <&vmem_3v3>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+		};
+
+		/* BT UART */
+		serial@80120000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 (BT_VREG_ON) */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* GPIO199 (BT_WAKE) */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* GPIO97 (BT_HOST_WAKE) */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default>;
+			};
+		};
+
+		/* GPF UART */
+		serial@80121000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+		};
+
+		/* Debugging console UART */
+		serial@80007000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				reg = <0x44>;
+
+				/* GPIO146 (PS_INT) */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux8_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&proximity_default>;
+
+				sharp,proximity-far-hysteresis = <0x40>;
+				sharp,proximity-close-hysteresis = <0x0f>;
+			};
+		};
+
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			imu@68 {
+				compatible = "invensense,mpu6050";
+				reg = <0x68>;
+
+				/* GPIO206 (ACC_INT) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <14 IRQ_TYPE_EDGE_RISING>;
+
+				mount-matrix = "0", "1", "0",
+					      "-1", "0", "0",
+					       "0", "0", "1";
+
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&imu_default>;
+			};
+		};
+
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			touchscreen@4a {
+				compatible = "atmel,maxtouch";
+				reg = <0x4a>;
+
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+
+				/* VDDA is "analog supply", 2.57-3.47 V */
+				vdda-supply = <&ab8500_ldo_aux2_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ab8500_ldo_aux5_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						regulator-name = "sensor_3v";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						regulator-name = "vreg_tsp_a3v3";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						regulator-name = "vdd_tf_2v91";
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "key_led_3.3v";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "vreg_tsp_1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "touch_key_2.2v";
+						regulator-min-microvolt = <2200000>;
+						regulator-max-microvolt = <2200000>;
+					};
+
+					ab8500_ldo_aux8 {
+						regulator-name = "sensor_1v8";
+					};
+				};
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel@0 {
+					compatible = "samsung,s6e63m0";
+					reg = <0>;
+					max-brightness = <15>;
+					vdd3-supply = <&panel_reg_3v0>;
+					vci-supply = <&panel_reg_1v8>;
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					/* ESD (electrostatic discharge) detection interrupt */
+					interrupt-parent = <&gpio2>;
+					interrupts = <18 IRQ_TYPE_EDGE_RISING>;
+					interrupt-names = "esd";
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		label = "GPIO Buttons";
+
+		volume-up {
+			label = "Volume Up";
+			/* GPIO67 (VOL_UP) */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			/* GPIO92 (VOL_DOWN) */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		home {
+			label = "Home";
+			/* GPIO91 (HOME_KEY) */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 (MOT_EN) */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	/* External LDO for eMMC */
+	vmem_3v3: regulator-vmem {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vmem_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		startup-delay-us = <200>;
+
+		/* GPIO223 (MEM_LDO_EN) */
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mem_ldo_default>;
+	};
+
+	/* TI TXS0206-29 level translator for 2.9 V */
+	sd_level_translator: regulator-sd-level-translator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+
+		startup-delay-us = <200>;
+
+		/* GPIO87 (TXS0206-29_EN) */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/*
+	 * WL_REG_ON takes WLAN out of reset and enables the internal regulators.
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the BCM chip is actually connected directly to VBAT.
+	 */
+	wl_reg_on: regulator-wl-reg-on {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+
+		startup-delay-us = <100000>;
+
+		/* GPIO215 (WLAN_EN) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default>;
+	};
+
+	/* MIC5366 GPIO-controlled regulator */
+	panel_reg_1v8: regulator-panel-1v8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "panel-fixed-supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+
+		startup-delay-us = <200>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reg_default_mode>;
+	};
+
+	/* MIC5366 GPIO-controlled regulator */
+	panel_reg_3v0: regulator-panel-3v0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "panel-fixed-supply";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+
+		startup-delay-us = <200>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_reg_default_mode>;
+	};
+};
+
+&pinctrl {
+	gpio-keys {
+		gpio_keys_default: gpio_keys_default {
+			golden_cfg1 {
+				pins = "GPIO67",	/* VOL_UP */
+				       "GPIO91",	/* HOME_KEY */
+				       "GPIO92";	/* VOL_DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			golden_cfg1 {
+				pins = "GPIO77",	/* TOUCHKEY_SCL */
+				       "GPIO78";	/* TOUCHKEY_SDA */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	flash {
+		gpio_flash_default_mode: flash_default {
+			golden_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			golden_cfg1 {
+				pins = "GPIO151",	/* COMP_SCL */
+				       "GPIO152";	/* COMP_SDA */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	touchkey {
+		touchkey_default: touchkey_default {
+			golden_cfg1 {
+				pins = "GPIO79";	/* TOUCHKEY_INT */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	sdi0 {
+		sd_level_translator_default: sd_level_translator_default {
+			golden_cfg1 {
+				pins = "GPIO87_B3";	/* TXS0206-29_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	sdi2 {
+		mem_ldo_default: mem_ldo_default {
+			golden_cfg1 {
+				pins = "GPIO223_AH9";	/* MEM_LDO_EN */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups =
+				"lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins =
+				"GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	display {
+		display_default_mode: display_default {
+			golden_cfg1 {
+				pins = "GPIO139_C9"; /* MIPI_DSI0_RESET_N */
+				ste,config = <&gpio_out_lo>;
+			};
+			golden_cfg2 {
+				pins = "GPIO82_C1"; /* LDI_ESD_DET */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+		panel_reg_default_mode: panel_reg_default {
+			golden_cfg1 {
+				pins = "GPIO219_AG10"; /* LCD_PWR_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	proximity {
+		proximity_default: proximity_default {
+			golden_cfg1 {
+				pins = "GPIO146_D13";	/* PS_INT */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	imu {
+		imu_default: imu_default {
+			golden_cfg1 {
+				pins = "GPIO206_AG24";	/* ACC_INT */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	tsp {
+		tsp_default: tsp_default {
+			golden_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	wlan {
+		wlan_default: wlan_default {
+			golden_cfg1 {
+				pins = "GPIO216_AG12";	/* WLAN_HOST_WAKE */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+
+		wlan_en_default: wlan_en_default {
+			golden_cfg1 {
+				pins = "GPIO215_AH13";	/* WLAN_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+
+	bluetooth {
+		bluetooth_default: bluetooth_default {
+			golden_cfg1 {
+				pins = "GPIO199_AH23",	/* BT_WAKE */
+				       "GPIO222_AJ9";	/* BT_VREG_ON */
+				ste,config = <&gpio_out_lo>;
+			};
+			golden_cfg2 {
+				pins = "GPIO97_D9";	/* BT_HOST_WAKE */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+
+	vibrator {
+		vibrator_default: vibrator_default {
+			golden_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			golden_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			golden_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts
new file mode 100644
index 000000000000..6e586e875565
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-janice.dts
@@ -0,0 +1,998 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy S Advance (GT-I9070)";
+	compatible = "samsung,janice", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb535151vu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchkeys.
+	 * Two GPIO lines controls two voltages of 3.3V and 1.8V
+	 * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8
+	 * EN_LED_LDO controls VREG_KLED_3V3 (key LED)
+	 */
+	ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_KLED_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO68 controls this regulator */
+		gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_led_ldo_default_mode>;
+	};
+	ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TOUCHKEY_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO89 controls this regulator */
+		gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_on2_default_mode>;
+	};
+
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas529_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * These pins do have an spi controller, however the controller on
+	 * these pins is not the fully featured PL022 SSP/SPI block but the
+	 * ST Micro diet "PL023" version. One of the lacking features in
+	 * this derivative is 3wire support, so it cannot be used to drive
+	 * this panel interface. We have to use GPIO bit-banging instead.
+	 */
+	spi {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220 */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MISO/MOSI on GPIO224 (no separate MISO pin) */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			vdd3-supply = <&lcd_3v0_reg>;
+			vci-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			spi-3wire;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Current sense amplifier on the light sensor to convert current to
+	 * voltage. We do not know if this is the actual configuration. The
+	 * sense resistor value was found by calibrating in a room ambient
+	 * light with a second mobile phone light sensor as reference. If you
+	 * pry a Janice phone apart and inspect it you may figure this out.
+	 */
+	gp2a_shunt: current-sense-shunt {
+		compatible = "current-sense-shunt";
+		io-channels = <&gpadc 0x07>;
+		shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */
+		#io-channel-cells = <0>;
+		io-channel-ranges;
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		clock-frequency = <400000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&ldo_kled_3v3_reg>;
+			vcc-supply = <&ldo_touchkey_1v8_reg>;
+			vddio-supply = <&ldo_touchkey_1v8_reg>;
+
+			/* Interrupt on GPIO 198 */
+			interrupt-parent = <&gpio6>;
+			interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_default_mode>;
+			linux,keycodes = <KEY_MENU KEY_BACK>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* This is only mounted on the GT-I9070P */
+		nfc@2b { /* 0x30? */
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn544_janice_default>;
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-dir-cmd;
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&ab8500_ldo_aux3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4330B1 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+
+			gnss {
+				/*
+				 * The Low Noise Amplifier (LNA) power and enablement is controlled
+				 * autonomously by the GSD4t.
+				 * Janice has a SiRFstarIV-based GSD4t
+				 * Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R.
+				 */
+				compatible = "csr,gsd4t";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO96 */
+				sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsd4t_janice_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <15000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				/* Janice has the GP2AP002A00F with light sensor */
+				compatible = "sharp,gp2ap002a00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux2_reg>;
+				/* ADC channel AUX2 to read ALSOUT ambient light sensor out */
+				io-channels = <&gp2a_shunt>;
+				io-channel-names = "alsout";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_janice_default>;
+				/* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+		/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
+		i2c@80122000 {
+			status = "okay";
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_janice_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				/* FIXME: no idea about this */
+				mount-matrix = "1", "0", "0",
+					       "0", "1", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_janice_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222 accelerometer */
+					accelerometer@8 {
+						compatible = "bosch,bma222";
+						reg = <0x08>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Atmel mXT224E touchscreen */
+			touchscreen@4a {
+				compatible = "atmel,maxtouch";
+				reg = <0x4a>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* VDDA is "analog supply", 2.57-3.47 V */
+				vdda-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			janice_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			janice_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			janice_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	key-led {
+		en_led_ldo_default_mode: en_led_ldo_default {
+			/* EN_LED_LDO on GPIO68 */
+			janice_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			janice_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			janice_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			janice_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enabled the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			janice_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			janice_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			janice_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS529 magnetometer */
+	yas529 {
+		yas529_default: yas529_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_janice_default: gp2ap002_janice {
+			janice_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_janice_default: mpu3050_janice {
+			janice_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Cypress touchkeys */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			janice_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			janice_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			janice_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* This pin is unused but belongs with this SPI block */
+			janice_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&in_pd>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			janice_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			janice_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_janice_default: tsu6111_janice {
+			janice_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	nfc {
+		pn544_janice_default: pn544_janice {
+			/* Interrupt line */
+			janice_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			janice_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	gsd4t {
+		gsd4t_janice_default: gsd4t_janice {
+			/* Reset line, start out asserted */
+			janice_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			janice_cfg2 {
+				pins = "GPIO96_D8";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* Unused power enablement line, used in R0.0 and R0.1 boards */
+			janice_cfg3 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts
new file mode 100644
index 000000000000..ba4421080b2a
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-kyle.dts
@@ -0,0 +1,727 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Amp SGH-I407 also known as Kyle.
+ *
+ * The code also refers to "Kyle AT&T" reflecting that this mobile phone
+ * was customized for the AT&T subsidiary Aio Wireless (All In One) and
+ * offered by the company in 2013.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Amp (SGH-I407)";
+	compatible = "samsung,kyle", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161la";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "en-3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator too */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	wlan_en: regulator-gpio-wlan-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <200000>;
+		/* GPIO215 WLAN_EN */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default_mode>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO 69 */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: this should be used by the NCP6914 Camera power management unit */
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux6_reg>;
+		};
+	};
+
+	soc {
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			vmmc-supply = <&wlan_en>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/*
+		 * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
+		 */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
+			post-power-on-delay-ms = <300>;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPF UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_kyle_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to AB8505 USB */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "AUX1";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Supplies the MMS touchscreen only with 3.3V */
+						regulator-name = "AUX2";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "AUX3";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "AUX4";
+						/* Hammer to 3.3V for the touchscreen */
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "AUX5";
+						/* 1.8V for the touchscreen */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "AUX6";
+						/* Used by sensors for 1.8 V in R0.1+ */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						/* Unused */
+						regulator-name = "AUX8";
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux6_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_kyle_default>;
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+		/* I2C2 */
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			accel@18 {
+				compatible = "bosch,bma254";
+				clock-frequency = <400000>;
+				reg = <0x18>;
+
+				mount-matrix = "-1", "0", "0",
+					       "0", "-1", "0",
+					       "0", "0", "-1";
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux6_reg>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Melfas MMS134S touchscreen */
+			touchscreen@48 {
+				compatible = "melfas,mms134s";
+				reg = <0x48>;
+				/* GPIO218 for IRQ */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* AVDD is "analog supply", 2.57-3.47 V */
+				avdd-supply = <&ab8500_ldo_aux2_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ab8500_ldo_aux5_reg>;
+
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&mms134s_kyle_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel {
+					/*
+					 * NT35510-based Hydis HVA40WV1
+					 * Apparently some Kyle models can have a NT35512 fitted
+					 * here instead. In that case the boot loader needs to
+					 * modify this compatible.
+					 */
+					compatible = "hydis,hva40wv1", "novatek,nt35510";
+					reg = <0>;
+					/* v_lcd_3v0 2.3-4.8V */
+					vdd-supply = <&lcd_3v0_reg>;
+					/* v_lcd_1v8 1.65-3.3V */
+					vddi-supply = <&lcd_1v8_reg>;
+					/* GPIO 139 */
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+					backlight = <&ktd253>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_1 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_1_default {
+			default_cfg1 {
+				/* GPIO18, 19 & 20 unused so pull down */
+				ste,config = <&gpio_in_pd>;
+			};
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins = "GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	/* Two GPIO lines used by the display */
+	display {
+		display_default_mode: display_default {
+			kyle_cfg1 {
+				/*
+				 * OLED DETECT or check_pba, this appears to be high
+				 * on "PBA" which I guess is "prototype board A".
+				 */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+			kyle_cfg2 {
+				pins = "GPIO139_C9";
+				/*
+				 * MIPI_DSI0_RESET_N resets the display, leave high
+				 * (de-asserted) so we only assert reset explicitly
+				 * from the display driver.
+				 */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			kyle_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+
+	backlight {
+		gpio_backlight_default_mode: backlight_default {
+			kyle_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	flash {
+		gpio_flash_default_mode: flash_default {
+			kyle_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			kyle_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			kyle_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			kyle_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+					ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_kyle_default: gp2ap002_kyle {
+			kyle_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			kyle_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for ALPS HSCD compass */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			kyle_cfg1 {
+				pins = "GPIO151_B17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			kyle_cfg1 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		wlan_en_default_mode: wlan_en_default {
+			kyle_cfg2 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			kyle_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			kyle_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			kyle_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Interrupt line for the Melfas MMS134S touchscreen */
+	touchscreen {
+		mms134s_kyle_default: mms134s_kyle {
+			kyle_cfg1 {
+				pins = "GPIO218_AH11";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	g05ta03 {
+		g05ta03_kyle_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			kyle_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			kyle_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			kyle_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			kyle_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts
new file mode 100644
index 000000000000..064d6fee8821
--- /dev/null
+++ b/arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts
@@ -0,0 +1,714 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung XCover 2 GT-S7710 also known as Skomer.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung XCover 2 (GT-S7710)";
+	compatible = "samsung,skomer", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb485159lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "en-3v3-fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	wlan_en: regulator-gpio-wlan-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wl-reg-on";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <200000>;
+		/* GPIO215 WLAN_EN */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default_mode>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+		button-menu {
+			linux,code = <KEY_MENU>;
+			label = "MENU";
+			/* GPIO204 */
+			gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+		};
+		button-back {
+			linux,code = <KEY_BACK>;
+			label = "BACK";
+			/* GPIO205 */
+			gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO 69 */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: this should be used by the NCP6914 Camera power management unit */
+	};
+
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			avdd-supply = <&ab8500_ldo_aux1_reg>;
+			dvdd-supply = <&ab8500_ldo_aux8_reg>;
+		};
+	};
+
+	soc {
+		// External Micro SD slot
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			/* All direction control is used */
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_1_default>;
+			pinctrl-1 = <&mc0_a_1_sleep>;
+			status = "okay";
+		};
+
+		// WLAN SDIO channel
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			vmmc-supply = <&wlan_en>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/*
+		 * eMMC seems to be mostly Samsung KLM4G1YE4C "4YMD1R"
+		 */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			/* From datasheet page 26 figure 9: 300 ms set-up time for 4GB */
+			post-power-on-delay-ms = <300>;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		serial@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			/* FIXME: not quite working yet, probably needs regulators */
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		serial@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_skomer_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to AB8505 USB */
+		serial@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <16000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "AUX1";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Supplies the Cypress TMA140 touchscreen only with 3.0V */
+						regulator-name = "AUX2";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "AUX3";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "AUX4";
+						/* Hammer to 3.0V for the display */
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "AUX5";
+						/* Intended for 1V8 for touchscreen but actually left unused */
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <2790000>;
+					};
+
+					ab8500_ldo_aux6 {
+						regulator-name = "AUX6";
+						/* Hammer to 1.8V for the display */
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						/* Mostly VIO for sensors */
+						regulator-name = "AUX8";
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				compatible = "sharp,gp2ap002s00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_skomer_default>;
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x2f>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+
+		/* I2C2 */
+		i2c@80128000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			accel@18 {
+				compatible = "bosch,bma254";
+				clock-frequency = <400000>;
+				reg = <0x18>;
+
+				/* GPIO224 used as "smart alert" interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+
+				mount-matrix = "0", "-1", "0",
+					      "1", "0", "0",
+					       "0", "0", "1";
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bma254_skomer_default>;
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Cypress CY8CTMA140 touchscreen */
+			touchscreen@20 {
+				compatible = "cypress,cy8ctma140";
+				clock-frequency = <400000>;
+				reg = <0x20>;
+
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				touchscreen-max-pressure = <255>;
+
+				/* GPIO218 for IRQ */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+
+				/* VDD is "digital supply" nominally 1.71-3.6V */
+				vdd-supply = <&ab8500_ldo_aux2_reg>;
+				/* VCPIN is "analog supply", 2.7-3.6 V */
+				vcpin-supply = <&ab8500_ldo_aux2_reg>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&tma140_skomer_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dsi_default_mode>;
+
+			dsi@a0351000 {
+				panel {
+					/* NT35510-based Hydis HVA40WV1 */
+					compatible = "hydis,hva40wv1", "novatek,nt35510";
+					reg = <0>;
+					/* v_lcd_3v0 2.3-4.8V */
+					vdd-supply = <&ab8500_ldo_aux4_reg>;
+					/* v_lcd_1v8 1.65-3.3V */
+					vddi-supply = <&ab8500_ldo_aux6_reg>;
+					/* GPIO 139 */
+					reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&display_default_mode>;
+					backlight = <&ktd253>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	sdi0 {
+		mc0_a_1_default {
+			default_cfg1 {
+				/* GPIO18, 19 & 20 unused so pull down */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	/* This is a reset line for the eMMC */
+	sdi2 {
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+
+	mcde {
+		dsi_default_mode: dsi_default {
+			default_mux1 {
+				/* Mux in VSI0 used for DSI TE */
+				function = "lcd";
+				groups = "lcdvsi0_a_1"; /* VSI0 for LCD */
+			};
+			default_cfg1 {
+				pins = "GPIO68_E1"; /* VSI0 */
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+
+	/* Two GPIO lines used by the display */
+	display {
+		display_default_mode: display_default {
+			skomer_cfg1 {
+				/*
+				 * OLED DETECT or check_pba, this appears to be high
+				 * on "PBA" which I guess is "prototype board A".
+				 */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+			skomer_cfg2 {
+				pins = "GPIO139_C9";
+				/*
+				 * MIPI_DSI0_RESET_N resets the display, leave high
+				 * (de-asserted) so we only assert reset explicitly
+				 * from the display driver.
+				 */
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	backlight {
+		gpio_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	flash {
+		gpio_flash_default_mode: flash_default {
+			skomer_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			skomer_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			skomer_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6", /* VOL DOWN */
+				       "GPIO204_AF23", /* MENU */
+				       "GPIO205_AG23"; /* BACK */
+					ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for BMA254 */
+	bma254 {
+		bma254_skomer_default: bma254_skomer {
+			skomer_cfg1 {
+				pins = "GPIO224_AG9";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_skomer_default: gp2ap002_skomer {
+			skomer_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			skomer_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for ALPS HSCD compass */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			skomer_cfg1 {
+				pins = "GPIO151_B17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			skomer_cfg1 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		wlan_en_default_mode: wlan_en_default {
+			skomer_cfg2 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			skomer_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			skomer_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			skomer_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Interrupt line for the Cypress TMA140 touchscreen */
+	touchscreen {
+		tma140_skomer_default: tma140_skomer {
+			skomer_cfg1 {
+				pins = "GPIO218_AH11";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	g05ta03 {
+		g05ta03_skomer_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			skomer_cfg1 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			skomer_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+};
+
+&ab8505_gpio {
+	/* Hog a few default settings */
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio_default>;
+
+	gpio {
+		gpio_default: gpio_default {
+			skomer_mux {
+				/* Change unused pins to GPIO mode */
+				function = "gpio";
+				groups = "gpio3_a_1",	/* default: SysClkReq4 */
+					 "gpio14_a_1";	/* default: PWMOut1 */
+			};
+			skomer_cfg1 {
+				pins = "GPIO11_B17", "GPIO13_D17", "GPIO50_L4";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih407-b2120.dts b/arch/arm/boot/dts/st/stih407-b2120.dts
new file mode 100644
index 000000000000..9c79982ee7ba
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407-b2120.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics (R&D) Limited.
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ */
+/dts-v1/;
+#include "stih407.dtsi"
+#include "stihxxx-b2120.dtsi"
+/ {
+	model = "STiH407 B2120";
+	compatible = "st,stih407-b2120", "st,stih407";
+
+	chosen {
+		stdout-path = &sbc_serial0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x80000000>;
+	};
+
+	aliases {
+		serial0 = &sbc_serial0;
+		ethernet0 = &ethernet0;
+	};
+
+};
diff --git a/arch/arm/boot/dts/st/stih407-clock.dtsi b/arch/arm/boot/dts/st/stih407-clock.dtsi
new file mode 100644
index 000000000000..350bcfcf498b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407-clock.dtsi
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih407-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih407-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih407-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih407-family.dtsi b/arch/arm/boot/dts/st/stih407-family.dtsi
new file mode 100644
index 000000000000..5ebb77947fd9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407-family.dtsi
@@ -0,0 +1,991 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics Limited.
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ */
+#include "stih407-pinctrl.dtsi"
+#include <dt-bindings/mfd/st-lpc.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/reset/stih407-resets.h>
+#include <dt-bindings/interrupt-controller/irq-st.h>
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gp0_reserved: rproc@45000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x45000000 0x00400000>;
+			no-map;
+		};
+
+		delta_reserved: rproc@44000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x44000000 0x01000000>;
+			no-map;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+
+			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
+			cpu-release-addr = <0x94100A4>;
+
+					 /* kHz     uV   */
+			operating-points = <1500000 0
+					    1200000 0
+					    800000  0
+					    500000  0>;
+
+			clocks = <&clk_m_a9>;
+			clock-names = "cpu";
+			clock-latency = <100000>;
+			cpu0-supply = <&pwm_regulator>;
+			st,syscfg = <&syscfg_core 0x8e0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+
+			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
+			cpu-release-addr = <0x94100A4>;
+
+					 /* kHz     uV   */
+			operating-points = <1500000 0
+					    1200000 0
+					    800000  0
+					    500000  0>;
+		};
+	};
+
+	intc: interrupt-controller@8761000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x08761000 0x1000>, <0x08760100 0x100>;
+	};
+
+	scu@8760000 {
+		compatible = "arm,cortex-a9-scu";
+		reg = <0x08760000 0x1000>;
+	};
+
+	timer@8760200 {
+		interrupt-parent = <&intc>;
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0x08760200 0x100>;
+		interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&arm_periph_clk>;
+	};
+
+	l2: cache-controller@8762000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x08762000 0x1000>;
+		arm,data-latency = <3 3 3>;
+		arm,tag-latency = <2 2 2>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	arm-pmu {
+		interrupt-parent = <&intc>;
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pwm_regulator: pwm-regulator {
+		compatible = "pwm-regulator";
+		pwms = <&pwm1 3 8448>;
+		regulator-name = "CPU_1V0_AVS";
+		regulator-min-microvolt = <784000>;
+		regulator-max-microvolt = <1299000>;
+		regulator-always-on;
+		max-duty-cycle = <255>;
+		status = "okay";
+	};
+
+	restart: restart-controller {
+		compatible = "st,stih407-restart";
+		st,syscfg = <&syscfg_sbc_reg>;
+		status = "okay";
+	};
+
+	powerdown: powerdown-controller {
+		compatible = "st,stih407-powerdown";
+		#reset-cells = <1>;
+	};
+
+	softreset: softreset-controller {
+		compatible = "st,stih407-softreset";
+		#reset-cells = <1>;
+	};
+
+	picophyreset: picophyreset-controller {
+		compatible = "st,stih407-picophyreset";
+		#reset-cells = <1>;
+	};
+
+	irq-syscfg {
+		compatible = "st,stih407-irq-syscfg";
+		st,syscfg = <&syscfg_core>;
+		st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+				<ST_IRQ_SYSCFG_PMU_1>;
+		st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+				<ST_IRQ_SYSCFG_DISABLED>;
+	};
+
+	usb2_picophy0: phy1 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0x100 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY2_RESET>;
+		reset-names = "global", "port";
+	};
+
+	miphy28lp_phy: miphy28lp {
+		compatible = "st,miphy28lp-phy";
+		st,syscfg = <&syscfg_core>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		phy_port0: port@9b22000 {
+			reg = <0x9b22000 0xff>,
+			      <0x9b09000 0xff>,
+			      <0x9b04000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
+
+			st,syscfg = <0x114 0x818 0xe0 0xec>;
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
+		};
+
+		phy_port1: port@9b2a000 {
+			reg = <0x9b2a000 0xff>,
+			      <0x9b19000 0xff>,
+			      <0x9b14000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
+
+			st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
+		};
+
+		phy_port2: port@8f95000 {
+			reg = <0x8f95000 0xff>,
+			      <0x8f90000 0xff>;
+			reg-names = "pipew",
+				    "usb3-up";
+
+			st,syscfg = <0x11c 0x820>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
+		};
+	};
+
+	st231_gp0: st231-gp0 {
+		compatible = "st,st231-rproc";
+		memory-region = <&gp0_reserved>;
+		resets = <&softreset STIH407_ST231_GP0_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x22c>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
+	};
+
+	st231_delta: st231-delta {
+		compatible = "st,st231-rproc";
+		memory-region = <&delta_reserved>;
+		resets = <&softreset STIH407_ST231_DMU_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x224>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+	};
+
+	delta0 {
+		compatible = "st,st-delta";
+		clock-names = "delta",
+			      "delta-st231",
+			      "delta-flash-promip";
+		clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+			 <&clk_s_c0_flexgen CLK_ST231_DMU>,
+			 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+		compatible = "simple-bus";
+
+		syscfg_sbc: sbc-syscfg@9620000 {
+			compatible = "st,stih407-sbc-syscfg", "syscon";
+			reg = <0x9620000 0x1000>;
+		};
+
+		syscfg_front: front-syscfg@9280000 {
+			compatible = "st,stih407-front-syscfg", "syscon";
+			reg = <0x9280000 0x1000>;
+		};
+
+		syscfg_rear: rear-syscfg@9290000 {
+			compatible = "st,stih407-rear-syscfg", "syscon";
+			reg = <0x9290000 0x1000>;
+		};
+
+		syscfg_flash: flash-syscfg@92a0000 {
+			compatible = "st,stih407-flash-syscfg", "syscon";
+			reg = <0x92a0000 0x1000>;
+		};
+
+		syscfg_sbc_reg: fvdp-lite-syscfg@9600000 {
+			compatible = "st,stih407-sbc-reg-syscfg", "syscon";
+			reg = <0x9600000 0x1000>;
+		};
+
+		syscfg_core: core-syscfg@92b0000 {
+			compatible = "st,stih407-core-syscfg", "syscon";
+			reg = <0x92b0000 0x1000>;
+
+			sti_sasg_codec: sti-sasg-codec {
+				compatible = "st,stih407-sas-codec";
+				#sound-dai-cells = <1>;
+				status = "disabled";
+				st,syscfg = <&syscfg_core>;
+			};
+		};
+
+		syscfg_lpm: lpm-syscfg@94b5100 {
+			compatible = "st,stih407-lpm-syscfg", "syscon";
+			reg = <0x94b5100 0x1000>;
+		};
+
+		/* Display */
+		vtg_main: sti-vtg-main@8d02800 {
+			compatible = "st,vtg";
+			reg = <0x8d02800 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		vtg_aux: sti-vtg-aux@8d00200 {
+			compatible = "st,vtg";
+			reg = <0x8d00200 0x100>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		serial@9830000 {
+			compatible = "st,asc";
+			reg = <0x9830000 0x2c>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			/* Pinctrl moved out to a per-board configuration */
+
+			status = "disabled";
+		};
+
+		serial@9831000 {
+			compatible = "st,asc";
+			reg = <0x9831000 0x2c>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_serial1>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+
+			status = "disabled";
+		};
+
+		serial@9832000 {
+			compatible = "st,asc";
+			reg = <0x9832000 0x2c>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_serial2>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+
+			status = "disabled";
+		};
+
+		/* SBC_ASC0 - UART10 */
+		sbc_serial0: serial@9530000 {
+			compatible = "st,asc";
+			reg = <0x9530000 0x2c>;
+			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sbc_serial0>;
+			clocks = <&clk_sysin>;
+
+			status = "disabled";
+		};
+
+		serial@9531000 {
+			compatible = "st,asc";
+			reg = <0x9531000 0x2c>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sbc_serial1>;
+			clocks = <&clk_sysin>;
+
+			status = "disabled";
+		};
+
+		i2c@9840000 {
+			compatible = "st,comms-ssc4-i2c";
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x9840000 0x110>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c0_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9841000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9841000 0x110>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c1_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9842000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9842000 0x110>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c2_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9843000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9843000 0x110>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c3_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9844000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9844000 0x110>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c4_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9845000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9845000 0x110>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c5_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+
+		/* SSCs on SBC */
+		i2c@9540000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9540000 0x110>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_sysin>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c10_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c@9541000 {
+			compatible = "st,comms-ssc4-i2c";
+			reg = <0x9541000 0x110>;
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_sysin>;
+			clock-names = "ssc";
+			clock-frequency = <400000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_i2c11_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9840000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9840000 0x110>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			pinctrl-0 = <&pinctrl_spi0_default>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9841000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9841000 0x110>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi1_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9842000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9842000 0x110>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi2_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9843000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9843000 0x110>;
+			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi3_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9844000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9844000 0x110>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi4_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		/* SBC SSC */
+		spi@9540000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9540000 0x110>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_sysin>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi10_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9541000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9541000 0x110>;
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_sysin>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi11_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		spi@9542000 {
+			compatible = "st,comms-ssc4-spi";
+			reg = <0x9542000 0x110>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_sysin>;
+			clock-names = "ssc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_spi12_default>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mmc0: sdhci@9060000 {
+			compatible = "st,sdhci-stih407", "st,sdhci";
+			status = "disabled";
+			reg = <0x09060000 0x7ff>, <0x9061008 0x20>;
+			reg-names = "mmc", "top-mmc-delay";
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mmcirq";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_mmc0>;
+			clock-names = "mmc", "icn";
+			clocks = <&clk_s_c0_flexgen CLK_MMC_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_HVA>;
+			bus-width = <8>;
+		};
+
+		mmc1: sdhci@9080000 {
+			compatible = "st,sdhci-stih407", "st,sdhci";
+			status = "disabled";
+			reg = <0x09080000 0x7ff>;
+			reg-names = "mmc";
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mmcirq";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sd1>;
+			clock-names = "mmc", "icn";
+			clocks = <&clk_s_c0_flexgen CLK_MMC_1>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_HVA>;
+			resets = <&softreset STIH407_MMC1_SOFTRESET>;
+			bus-width = <4>;
+		};
+
+		/* Watchdog and Real-Time Clock */
+		lpc@8787000 {
+			compatible = "st,stih407-lpc";
+			reg = <0x8787000 0x1000>;
+			interrupts = <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clk_s_d3_flexgen CLK_LPC_0>;
+			timeout-sec = <120>;
+			st,syscfg = <&syscfg_core>;
+			st,lpc-mode = <ST_LPC_MODE_WDT>;
+		};
+
+		lpc@8788000 {
+			compatible = "st,stih407-lpc";
+			reg = <0x8788000 0x1000>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clk_s_d3_flexgen CLK_LPC_1>;
+			st,lpc-mode = <ST_LPC_MODE_CLKSRC>;
+		};
+
+		spifsm: spifsm@9022000{
+			compatible = "st,spi-fsm";
+			reg = <0x9022000 0x1000>;
+			reg-names = "spi-fsm";
+			clocks = <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+			clock-names = "emi_clk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fsm>;
+			st,syscfg = <&syscfg_core>;
+			st,boot-device-reg = <0x8c4>;
+			st,boot-device-spi = <0x68>;
+
+			status = "disabled";
+		};
+
+		sata0: sata@9b20000 {
+			compatible = "st,ahci";
+			reg = <0x9b20000 0x1000>;
+
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hostc";
+
+			phys = <&phy_port0 PHY_TYPE_SATA>;
+			phy-names = "ahci_phy";
+
+			resets = <&powerdown STIH407_SATA0_POWERDOWN>,
+				 <&softreset STIH407_SATA0_SOFTRESET>,
+				 <&softreset STIH407_SATA0_PWR_SOFTRESET>;
+			reset-names = "pwr-dwn", "sw-rst", "pwr-rst";
+
+			clock-names = "ahci_clk";
+			clocks = <&clk_s_c0_flexgen CLK_ICN_REG>;
+
+			ports-implemented = <0x1>;
+
+			status = "disabled";
+		};
+
+		sata1: sata@9b28000 {
+			compatible = "st,ahci";
+			reg = <0x9b28000 0x1000>;
+
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hostc";
+
+			phys = <&phy_port1 PHY_TYPE_SATA>;
+			phy-names = "ahci_phy";
+
+			resets = <&powerdown STIH407_SATA1_POWERDOWN>,
+				 <&softreset STIH407_SATA1_SOFTRESET>,
+				 <&softreset STIH407_SATA1_PWR_SOFTRESET>;
+			reset-names = "pwr-dwn",
+				      "sw-rst",
+				      "pwr-rst";
+
+			clock-names = "ahci_clk";
+			clocks = <&clk_s_c0_flexgen CLK_ICN_REG>;
+
+			ports-implemented = <0x1>;
+
+			status = "disabled";
+		};
+
+
+		st_dwc3: dwc3@8f94000 {
+			compatible = "st,stih407-dwc3";
+			reg = <0x08f94000 0x1000>, <0x110 0x4>;
+			reg-names = "reg-glue", "syscfg-reg";
+			st,syscfg = <&syscfg_core>;
+			resets = <&powerdown STIH407_USB3_POWERDOWN>,
+				 <&softreset STIH407_MIPHY2_SOFTRESET>;
+			reset-names = "powerdown", "softreset";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb3>;
+			ranges;
+
+			status = "disabled";
+
+			dwc3: usb@9900000 {
+				compatible = "snps,dwc3";
+				reg = <0x09900000 0x100000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				phy-names = "usb2-phy", "usb3-phy";
+				phys = <&usb2_picophy0>,
+				       <&phy_port2 PHY_TYPE_USB3>;
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		/* COMMS PWM Module */
+		pwm0: pwm@9810000 {
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9810000 0x68>;
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm0_chan0_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
+			st,pwm-num-chan = <1>;
+
+			status = "disabled";
+		};
+
+		/* SBC PWM Module */
+		pwm1: pwm@9510000 {
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9510000 0x68>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm1_chan0_default
+				     &pinctrl_pwm1_chan1_default
+				     &pinctrl_pwm1_chan2_default
+				     &pinctrl_pwm1_chan3_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
+			st,pwm-num-chan = <4>;
+
+			status = "disabled";
+		};
+
+		rng10: rng@8a89000 {
+			compatible = "st,rng";
+			reg = <0x08a89000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
+		};
+
+		rng11: rng@8a8a000 {
+			compatible = "st,rng";
+			reg = <0x08a8a000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
+		};
+
+		ethernet0: dwmac@9630000 {
+			device_type = "network";
+			status = "disabled";
+			compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+			reg = <0x9630000 0x8000>, <0x80 0x4>;
+			reg-names = "stmmaceth", "sti-ethconf";
+
+			st,syscon = <&syscfg_sbc_reg 0x80>;
+			st,gmac_en;
+			resets = <&softreset STIH407_ETH1_SOFTRESET>;
+			reset-names = "stmmaceth";
+
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq";
+
+			/* DMA Bus Mode */
+			snps,pbl = <8>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_rgmii1>;
+
+			clock-names = "stmmaceth", "sti-ethclk";
+			clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+				 <&clk_s_c0_flexgen CLK_ETH_PHY>;
+		};
+
+		mailbox0: mailbox@8f00000  {
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f00000 0x1000>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+			mbox-name = "a9";
+			status = "okay";
+		};
+
+		mailbox1: mailbox@8f01000 {
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f01000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_1";
+			status = "okay";
+		};
+
+		mailbox2: mailbox@8f02000 {
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f02000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_0";
+			status = "okay";
+		};
+
+		mailbox3: mailbox@8f03000 {
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f03000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_audio_video";
+			status = "okay";
+		};
+
+		/* fdma audio */
+		fdma0: dma-controller@8e20000 {
+			compatible = "st,stih407-fdma-mpe31-11", "st,slim-rproc";
+			reg = <0x8e20000 0x8000>,
+			      <0x8e30000 0x3000>,
+			      <0x8e37000 0x1000>,
+			      <0x8e38000 0x8000>;
+			reg-names = "slimcore", "dmem", "peripherals", "imem";
+			clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+				 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+				 <&clk_s_c0_flexgen CLK_EXT2F_A9>,
+				 <&clk_s_c0_flexgen CLK_EXT2F_A9>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <3>;
+		};
+
+		/* fdma app */
+		fdma1: dma-controller@8e40000 {
+			compatible = "st,stih407-fdma-mpe31-12", "st,slim-rproc";
+			reg = <0x8e40000 0x8000>,
+			      <0x8e50000 0x3000>,
+			      <0x8e57000 0x1000>,
+			      <0x8e58000 0x8000>;
+			reg-names = "slimcore", "dmem", "peripherals", "imem";
+			clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+				<&clk_s_c0_flexgen CLK_TX_ICN_DMU>,
+				<&clk_s_c0_flexgen CLK_TX_ICN_DMU>,
+				<&clk_s_c0_flexgen CLK_EXT2F_A9>;
+
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <3>;
+
+			status = "disabled";
+		};
+
+		/* fdma free running */
+		fdma2: dma-controller@8e60000 {
+			compatible = "st,stih407-fdma-mpe31-13", "st,slim-rproc";
+			reg = <0x8e60000 0x8000>,
+			      <0x8e70000 0x3000>,
+			      <0x8e77000 0x1000>,
+			      <0x8e78000 0x8000>;
+			reg-names = "slimcore", "dmem", "peripherals", "imem";
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <3>;
+			clocks = <&clk_s_c0_flexgen CLK_FDMA>,
+				<&clk_s_c0_flexgen CLK_EXT2F_A9>,
+				<&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				<&clk_s_c0_flexgen CLK_EXT2F_A9>;
+
+			status = "disabled";
+		};
+
+		sti_uni_player0: sti-uni-player@8d80000 {
+			compatible = "st,stih407-uni-player-hdmi";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			clocks = <&clk_s_d0_flexgen CLK_PCM_0>;
+			assigned-clocks = <&clk_s_d0_quadfs 0>, <&clk_s_d0_flexgen CLK_PCM_0>;
+			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 0>;
+			assigned-clock-rates = <50000000>;
+			reg = <0x8d80000 0x158>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 2 0 1>;
+			dma-names = "tx";
+
+			status = "disabled";
+		};
+
+		sti_uni_player1: sti-uni-player@8d81000 {
+			compatible = "st,stih407-uni-player-pcm-out";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			clocks = <&clk_s_d0_flexgen CLK_PCM_1>;
+			assigned-clocks = <&clk_s_d0_quadfs 1>, <&clk_s_d0_flexgen CLK_PCM_1>;
+			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 1>;
+			assigned-clock-rates = <50000000>;
+			reg = <0x8d81000 0x158>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 3 0 1>;
+			dma-names = "tx";
+
+			status = "disabled";
+		};
+
+		sti_uni_player2: sti-uni-player@8d82000 {
+			compatible = "st,stih407-uni-player-dac";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			clocks = <&clk_s_d0_flexgen CLK_PCM_2>;
+			assigned-clocks = <&clk_s_d0_quadfs 2>, <&clk_s_d0_flexgen CLK_PCM_2>;
+			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 2>;
+			assigned-clock-rates = <50000000>;
+			reg = <0x8d82000 0x158>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 4 0 1>;
+			dma-names = "tx";
+
+			status = "disabled";
+		};
+
+		sti_uni_player3: sti-uni-player@8d85000 {
+			compatible = "st,stih407-uni-player-spdif";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			clocks = <&clk_s_d0_flexgen CLK_SPDIFF>;
+			assigned-clocks = <&clk_s_d0_quadfs 3>, <&clk_s_d0_flexgen CLK_SPDIFF>;
+			assigned-clock-parents = <0>, <&clk_s_d0_quadfs 3>;
+			assigned-clock-rates = <50000000>;
+			reg = <0x8d85000 0x158>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 7 0 1>;
+			dma-names = "tx";
+
+			status = "disabled";
+		};
+
+		sti_uni_reader0: sti-uni-reader@8d83000 {
+			compatible = "st,stih407-uni-reader-pcm_in";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			reg = <0x8d83000 0x158>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 5 0 1>;
+			dma-names = "rx";
+
+			status = "disabled";
+		};
+
+		sti_uni_reader1: sti-uni-reader@8d84000 {
+			compatible = "st,stih407-uni-reader-hdmi";
+			#sound-dai-cells = <0>;
+			st,syscfg = <&syscfg_core>;
+			reg = <0x8d84000 0x158>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&fdma0 6 0 1>;
+			dma-names = "rx";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih407-pinctrl.dtsi b/arch/arm/boot/dts/st/stih407-pinctrl.dtsi
new file mode 100644
index 000000000000..2cf335714ca2
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407-pinctrl.dtsi
@@ -0,0 +1,1262 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics Limited.
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ */
+#include "st-pincfg.h"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+/ {
+
+	aliases {
+		/* 0-5: PIO_SBC */
+		gpio0 = &pio0;
+		gpio1 = &pio1;
+		gpio2 = &pio2;
+		gpio3 = &pio3;
+		gpio4 = &pio4;
+		gpio5 = &pio5;
+		/* 10-19: PIO_FRONT0 */
+		gpio6 = &pio10;
+		gpio7 = &pio11;
+		gpio8 = &pio12;
+		gpio9 = &pio13;
+		gpio10 = &pio14;
+		gpio11 = &pio15;
+		gpio12 = &pio16;
+		gpio13 = &pio17;
+		gpio14 = &pio18;
+		gpio15 = &pio19;
+		/* 20: PIO_FRONT1 */
+		gpio16 = &pio20;
+		/* 30-35: PIO_REAR */
+		gpio17 = &pio30;
+		gpio18 = &pio31;
+		gpio19 = &pio32;
+		gpio20 = &pio33;
+		gpio21 = &pio34;
+		gpio22 = &pio35;
+		/* 40-42: PIO_FLASH */
+		gpio23 = &pio40;
+		gpio24 = &pio41;
+		gpio25 = &pio42;
+	};
+
+	soc {
+		pin-controller-sbc@961f080 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stih407-sbc-pinctrl";
+			st,syscfg = <&syscfg_sbc>;
+			reg = <0x0961f080 0x4>;
+			reg-names = "irqmux";
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
+			ranges = <0 0x09610000 0x6000>;
+
+			pio0: gpio@9610000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x100>;
+				st,bank-name = "PIO0";
+			};
+			pio1: gpio@9611000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x100>;
+				st,bank-name = "PIO1";
+			};
+			pio2: gpio@9612000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x100>;
+				st,bank-name = "PIO2";
+			};
+			pio3: gpio@9613000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x100>;
+				st,bank-name = "PIO3";
+			};
+			pio4: gpio@9614000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x100>;
+				st,bank-name = "PIO4";
+			};
+
+			pio5: gpio@9615000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x100>;
+				st,bank-name = "PIO5";
+				st,retime-pin-mask = <0x3f>;
+			};
+
+			cec0 {
+				pinctrl_cec0_default: cec0-default {
+					st,pins {
+						hdmi_cec = <&pio2 4 ALT1 BIDIR>;
+					};
+				};
+			};
+
+			rc {
+				pinctrl_ir: ir0 {
+					st,pins {
+						ir = <&pio4 0 ALT2 IN>;
+					};
+				};
+
+				pinctrl_uhf: uhf0 {
+					st,pins {
+						ir = <&pio4 1 ALT2 IN>;
+					};
+				};
+
+				pinctrl_tx: tx0 {
+					st,pins {
+						tx = <&pio4 2 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_tx_od: tx_od0 {
+					st,pins {
+						tx_od = <&pio4 3 ALT2 OUT>;
+					};
+				};
+			};
+
+			/* SBC_ASC0 - UART10 */
+			sbc_serial0 {
+				pinctrl_sbc_serial0: sbc_serial0-0 {
+					st,pins {
+						tx = <&pio3 4 ALT1 OUT>;
+						rx = <&pio3 5 ALT1 IN>;
+					};
+				};
+			};
+			/* SBC_ASC1 - UART11 */
+			sbc_serial1 {
+				pinctrl_sbc_serial1: sbc_serial1-0 {
+					st,pins {
+						tx = <&pio2 6 ALT3 OUT>;
+						rx = <&pio2 7 ALT3 IN>;
+					};
+				};
+			};
+
+			i2c10 {
+				pinctrl_i2c10_default: i2c10-default {
+					st,pins {
+						sda = <&pio4 6 ALT1 BIDIR>;
+						scl = <&pio4 5 ALT1 BIDIR>;
+					};
+				};
+			};
+
+			i2c11 {
+				pinctrl_i2c11_default: i2c11-default {
+					st,pins {
+						sda = <&pio5 1 ALT1 BIDIR>;
+						scl = <&pio5 0 ALT1 BIDIR>;
+					};
+				};
+			};
+
+			keyscan {
+				pinctrl_keyscan: keyscan {
+					st,pins {
+						keyin0 = <&pio4 0 ALT6 IN>;
+						keyin1 = <&pio4 5 ALT4 IN>;
+						keyin2 = <&pio0 4 ALT2 IN>;
+						keyin3 = <&pio2 6 ALT2 IN>;
+
+						keyout0 = <&pio4 6 ALT4 OUT>;
+						keyout1 = <&pio1 7 ALT2 OUT>;
+						keyout2 = <&pio0 6 ALT2 OUT>;
+						keyout3 = <&pio2 7 ALT2 OUT>;
+					};
+				};
+			};
+
+			gmac1 {
+				/*
+				 * Almost all the boards based on STiH407 SoC have an embedded
+				 * switch where the mdio/mdc have been used for managing the SMI
+				 * iface via I2C. For this reason these lines can be allocated
+				 * by using dedicated configuration (in case of there will be a
+				 * standard PHY transceiver on-board).
+				 */
+				pinctrl_rgmii1: rgmii1-0 {
+					st,pins {
+
+						txd0 = <&pio0 0 ALT1 OUT DE_IO 0 CLK_A>;
+						txd1 = <&pio0 1 ALT1 OUT DE_IO 0 CLK_A>;
+						txd2 = <&pio0 2 ALT1 OUT DE_IO 0 CLK_A>;
+						txd3 = <&pio0 3 ALT1 OUT DE_IO 0 CLK_A>;
+						txen = <&pio0 5 ALT1 OUT DE_IO 0 CLK_A>;
+						txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+						rxd0 = <&pio1 4 ALT1 IN DE_IO 0 CLK_A>;
+						rxd1 = <&pio1 5 ALT1 IN DE_IO 0 CLK_A>;
+						rxd2 = <&pio1 6 ALT1 IN DE_IO 0 CLK_A>;
+						rxd3 = <&pio1 7 ALT1 IN DE_IO 0 CLK_A>;
+						rxdv = <&pio2 0 ALT1 IN DE_IO 0 CLK_A>;
+						rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+						clk125 = <&pio3 7 ALT4 IN NICLK 0 CLK_A>;
+						phyclk = <&pio2 3 ALT4 OUT NICLK 1250 CLK_B>;
+					};
+				};
+
+				pinctrl_rgmii1_mdio: rgmii1-mdio {
+					st,pins {
+						mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+						mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+						mdint = <&pio1 3 ALT1 IN BYPASS 0>;
+					};
+				};
+
+				pinctrl_rgmii1_mdio_1: rgmii1-mdio-1 {
+					st,pins {
+						mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+						mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+					};
+				};
+
+				pinctrl_mii1: mii1 {
+					st,pins {
+						txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd2 = <&pio0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd3 = <&pio0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txer = <&pio0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txclk = <&pio0 6 ALT1 IN NICLK 0 CLK_A>;
+						col = <&pio0 7 ALT1 IN BYPASS 1000>;
+
+						mdio = <&pio1 0 ALT1 OUT BYPASS 1500>;
+						mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+						crs = <&pio1 2 ALT1 IN BYPASS 1000>;
+						mdint = <&pio1 3 ALT1 IN BYPASS 0>;
+						rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd2 = <&pio1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd3 = <&pio1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+						rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxclk = <&pio2 2 ALT1 IN NICLK 0 CLK_A>;
+						phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>;
+					};
+				};
+
+				pinctrl_rmii1: rmii1-0 {
+					st,pins {
+						txd0 = <&pio0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd1 = <&pio0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txen = <&pio0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						mdio = <&pio1 0 ALT1 OUT BYPASS 0>;
+						mdc = <&pio1 1 ALT1 OUT NICLK 0 CLK_A>;
+						mdint = <&pio1 3 ALT1 IN BYPASS 0>;
+						rxd0 = <&pio1 4 ALT1 IN SE_NICLK_IO 0 CLK_B>;
+						rxd1 = <&pio1 5 ALT1 IN SE_NICLK_IO 0 CLK_B>;
+						rxdv = <&pio2 0 ALT1 IN SE_NICLK_IO 0 CLK_B>;
+						rx_er = <&pio2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+
+				pinctrl_rmii1_phyclk: rmii1_phyclk {
+					st,pins {
+						phyclk = <&pio2 3 ALT1 OUT NICLK 0 CLK_A>;
+					};
+				};
+
+				pinctrl_rmii1_phyclk_ext: rmii1_phyclk_ext {
+					st,pins {
+						phyclk = <&pio2 3 ALT2 IN NICLK 0 CLK_A>;
+					};
+				};
+			};
+
+			pwm1 {
+				pinctrl_pwm1_chan0_default: pwm1-0-default {
+					st,pins {
+						pwm-out = <&pio3 0 ALT1 OUT>;
+						pwm-capturein = <&pio3 2 ALT1 IN>;
+					};
+				};
+				pinctrl_pwm1_chan1_default: pwm1-1-default {
+					st,pins {
+						pwm-capturein = <&pio4 3 ALT1 IN>;
+						pwm-out = <&pio4 4 ALT1 OUT>;
+					};
+				};
+				pinctrl_pwm1_chan2_default: pwm1-2-default {
+					st,pins {
+						pwm-out = <&pio4 6 ALT3 OUT>;
+					};
+				};
+				pinctrl_pwm1_chan3_default: pwm1-3-default {
+					st,pins {
+						pwm-out = <&pio4 7 ALT3 OUT>;
+					};
+				};
+			};
+
+			spi10 {
+				pinctrl_spi10_default: spi10-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio4 6 ALT1 OUT>;
+						mrst = <&pio4 7 ALT1 IN>;
+						scl = <&pio4 5 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi10_3w_alt1_0: spi10-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio4 6 ALT1 BIDIR_PU>;
+						scl = <&pio4 5 ALT1 OUT>;
+					};
+				};
+			};
+
+			spi11 {
+				pinctrl_spi11_default: spi11-4w-alt2-0 {
+					st,pins {
+						mtsr = <&pio3 1 ALT2 OUT>;
+						mrst = <&pio3 0 ALT2 IN>;
+						scl = <&pio3 2 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi11_3w_alt2_0: spi11-3w-alt2-0 {
+					st,pins {
+						mtsr = <&pio3 1 ALT2 BIDIR_PU>;
+						scl = <&pio3 2 ALT2 OUT>;
+					};
+				};
+			};
+
+			spi12 {
+				pinctrl_spi12_default: spi12-4w-alt2-0 {
+					st,pins {
+						mtsr = <&pio3 6 ALT2 OUT>;
+						mrst = <&pio3 4 ALT2 IN>;
+						scl = <&pio3 7 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi12_3w_alt2_0: spi12-3w-alt2-0 {
+					st,pins {
+						mtsr = <&pio3 6 ALT2 BIDIR_PU>;
+						scl = <&pio3 7 ALT2 OUT>;
+					};
+				};
+			};
+		};
+
+		pin-controller-front0@920f080 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stih407-front-pinctrl";
+			st,syscfg = <&syscfg_front>;
+			reg = <0x0920f080 0x4>;
+			reg-names = "irqmux";
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
+			ranges = <0 0x09200000 0x10000>;
+
+			pio10: pio@9200000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x100>;
+				st,bank-name = "PIO10";
+			};
+			pio11: pio@9201000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x100>;
+				st,bank-name = "PIO11";
+			};
+			pio12: pio@9202000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x100>;
+				st,bank-name = "PIO12";
+			};
+			pio13: pio@9203000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x100>;
+				st,bank-name = "PIO13";
+			};
+			pio14: pio@9204000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x100>;
+				st,bank-name = "PIO14";
+			};
+			pio15: pio@9205000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x100>;
+				st,bank-name = "PIO15";
+			};
+			pio16: pio@9206000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x100>;
+				st,bank-name = "PIO16";
+			};
+			pio17: pio@9207000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x100>;
+				st,bank-name = "PIO17";
+			};
+			pio18: pio@9208000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x100>;
+				st,bank-name = "PIO18";
+			};
+			pio19: pio@9209000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x9000 0x100>;
+				st,bank-name = "PIO19";
+			};
+
+			/* Comms */
+			serial0 {
+				pinctrl_serial0: serial0-0 {
+					st,pins {
+						tx =  <&pio17 0 ALT1 OUT>;
+						rx =  <&pio17 1 ALT1 IN>;
+					};
+				};
+				pinctrl_serial0_hw_flowctrl: serial0-0_hw_flowctrl {
+					st,pins {
+						tx =  <&pio17 0 ALT1 OUT>;
+						rx =  <&pio17 1 ALT1 IN>;
+						cts = <&pio17 2 ALT1 IN>;
+						rts = <&pio17 3 ALT1 OUT>;
+					};
+				};
+			};
+
+			serial1 {
+				pinctrl_serial1: serial1-0 {
+					st,pins {
+						tx = <&pio16 0 ALT1 OUT>;
+						rx = <&pio16 1 ALT1 IN>;
+					};
+				};
+			};
+
+			serial2 {
+				pinctrl_serial2: serial2-0 {
+					st,pins {
+						tx = <&pio15 0 ALT1 OUT>;
+						rx = <&pio15 1 ALT1 IN>;
+					};
+				};
+			};
+
+			mmc1 {
+				pinctrl_sd1: sd1-0 {
+					st,pins {
+						sd_clk = <&pio19 3 ALT5 BIDIR NICLK 0 CLK_B>;
+						sd_cmd = <&pio19 2 ALT5 BIDIR_PU BYPASS 0>;
+						sd_dat0 = <&pio19 4 ALT5 BIDIR_PU BYPASS 0>;
+						sd_dat1 = <&pio19 5 ALT5 BIDIR_PU BYPASS 0>;
+						sd_dat2 = <&pio19 6 ALT5 BIDIR_PU BYPASS 0>;
+						sd_dat3 = <&pio19 7 ALT5 BIDIR_PU BYPASS 0>;
+						sd_led = <&pio16 6 ALT6 OUT>;
+						sd_pwren = <&pio16 7 ALT6 OUT>;
+						sd_cd = <&pio19 0 ALT6 IN>;
+						sd_wp = <&pio19 1 ALT6 IN>;
+					};
+				};
+			};
+
+
+			i2c0 {
+				pinctrl_i2c0_default: i2c0-default {
+					st,pins {
+						sda = <&pio10 6 ALT2 BIDIR>;
+						scl = <&pio10 5 ALT2 BIDIR>;
+					};
+				};
+			};
+
+			i2c1 {
+				pinctrl_i2c1_default: i2c1-default {
+					st,pins {
+						sda = <&pio11 1 ALT2 BIDIR>;
+						scl = <&pio11 0 ALT2 BIDIR>;
+					};
+				};
+			};
+
+			i2c2 {
+				pinctrl_i2c2_default: i2c2-default {
+					st,pins {
+						sda = <&pio15 6 ALT2 BIDIR>;
+						scl = <&pio15 5 ALT2 BIDIR>;
+					};
+				};
+
+				pinctrl_i2c2_alt2_1: i2c2-alt2-1 {
+					st,pins {
+						sda = <&pio12 6 ALT2 BIDIR>;
+						scl = <&pio12 5 ALT2 BIDIR>;
+					};
+				};
+			};
+
+			i2c3 {
+				pinctrl_i2c3_default: i2c3-alt1-0 {
+					st,pins {
+						sda = <&pio18 6 ALT1 BIDIR>;
+						scl = <&pio18 5 ALT1 BIDIR>;
+					};
+				};
+				pinctrl_i2c3_alt1_1: i2c3-alt1-1 {
+					st,pins {
+						sda = <&pio17 7 ALT1 BIDIR>;
+						scl = <&pio17 6 ALT1 BIDIR>;
+					};
+				};
+				pinctrl_i2c3_alt3_0: i2c3-alt3-0 {
+					st,pins {
+						sda = <&pio13 6 ALT3 BIDIR>;
+						scl = <&pio13 5 ALT3 BIDIR>;
+					};
+				};
+			};
+
+			spi0 {
+				pinctrl_spi0_default: spi0-4w-alt2-0 {
+					st,pins {
+						mtsr = <&pio10 6 ALT2 OUT>;
+						mrst = <&pio10 7 ALT2 IN>;
+						scl = <&pio10 5 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi0_3w_alt2_0: spi0-3w-alt2-0 {
+					st,pins {
+						mtsr = <&pio10 6 ALT2 BIDIR_PU>;
+						scl = <&pio10 5 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi0_4w_alt1_0: spi0-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio19 7 ALT1 OUT>;
+						mrst = <&pio19 5 ALT1 IN>;
+						scl = <&pio19 6 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi0_3w_alt1_0: spi0-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio19 7 ALT1 BIDIR_PU>;
+						scl = <&pio19 6 ALT1 OUT>;
+					};
+				};
+			};
+
+			spi1 {
+				pinctrl_spi1_default: spi1-4w-alt2-0 {
+					st,pins {
+						mtsr = <&pio11 1 ALT2 OUT>;
+						mrst = <&pio11 2 ALT2 IN>;
+						scl = <&pio11 0 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi1_3w_alt2_0: spi1-3w-alt2-0 {
+					st,pins {
+						mtsr = <&pio11 1 ALT2 BIDIR_PU>;
+						scl = <&pio11 0 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi1_4w_alt1_0: spi1-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio14 3 ALT1 OUT>;
+						mrst = <&pio14 4 ALT1 IN>;
+						scl = <&pio14 2 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi1_3w_alt1_0: spi1-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio14 3 ALT1 BIDIR_PU>;
+						scl = <&pio14 2 ALT1 OUT>;
+					};
+				};
+			};
+
+			spi2 {
+				pinctrl_spi2_default: spi2-4w-alt2-0 {
+					st,pins {
+						mtsr = <&pio12 6 ALT2 OUT>;
+						mrst = <&pio12 7 ALT2 IN>;
+						scl = <&pio12 5 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi2_3w_alt2_0: spi2-3w-alt2-0 {
+					st,pins {
+						mtsr = <&pio12 6 ALT2 BIDIR_PU>;
+						scl = <&pio12 5 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi2_4w_alt1_0: spi2-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio14 6 ALT1 OUT>;
+						mrst = <&pio14 7 ALT1 IN>;
+						scl = <&pio14 5 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi2_3w_alt1_0: spi2-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio14 6 ALT1 BIDIR_PU>;
+						scl = <&pio14 5 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi2_4w_alt2_1: spi2-4w-alt2-1 {
+					st,pins {
+						mtsr = <&pio15 6 ALT2 OUT>;
+						mrst = <&pio15 7 ALT2 IN>;
+						scl = <&pio15 5 ALT2 OUT>;
+					};
+				};
+
+				pinctrl_spi2_3w_alt2_1: spi2-3w-alt2-1 {
+					st,pins {
+						mtsr = <&pio15 6 ALT2 BIDIR_PU>;
+						scl = <&pio15 5 ALT2 OUT>;
+					};
+				};
+			};
+
+			spi3 {
+				pinctrl_spi3_default: spi3-4w-alt3-0 {
+					st,pins {
+						mtsr = <&pio13 6 ALT3 OUT>;
+						mrst = <&pio13 7 ALT3 IN>;
+						scl = <&pio13 5 ALT3 OUT>;
+					};
+				};
+
+				pinctrl_spi3_3w_alt3_0: spi3-3w-alt3-0 {
+					st,pins {
+						mtsr = <&pio13 6 ALT3 BIDIR_PU>;
+						scl = <&pio13 5 ALT3 OUT>;
+					};
+				};
+
+				pinctrl_spi3_4w_alt1_0: spi3-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio17 7 ALT1 OUT>;
+						mrst = <&pio17 5 ALT1 IN>;
+						scl = <&pio17 6 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi3_3w_alt1_0: spi3-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio17 7 ALT1 BIDIR_PU>;
+						scl = <&pio17 6 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi3_4w_alt1_1: spi3-4w-alt1-1 {
+					st,pins {
+						mtsr = <&pio18 6 ALT1 OUT>;
+						mrst = <&pio18 7 ALT1 IN>;
+						scl = <&pio18 5 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi3_3w_alt1_1: spi3-3w-alt1-1 {
+					st,pins {
+						mtsr = <&pio18 6 ALT1 BIDIR_PU>;
+						scl = <&pio18 5 ALT1 OUT>;
+					};
+				};
+			};
+
+			tsin0 {
+				pinctrl_tsin0_parallel: tsin0_parallel {
+					st,pins {
+						DATA7 = <&pio10 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio10 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio10 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio10 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio11 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio11 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio11 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio11 3 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin0_serial: tsin0_serial {
+					st,pins {
+						DATA7 = <&pio10 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsin1 {
+				pinctrl_tsin1_parallel: tsin1_parallel {
+					st,pins {
+						DATA7 = <&pio12 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio12 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio12 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio12 3 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio12 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio12 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio12 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio12 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio11 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin1_serial: tsin1_serial {
+					st,pins {
+						DATA7 = <&pio12 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio11 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsin2 {
+				pinctrl_tsin2_parallel: tsin2_parallel {
+					st,pins {
+						DATA7 = <&pio13 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio13 5 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA5 = <&pio13 6 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA4 = <&pio13 7 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA3 = <&pio14 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio14 1 ALT2 IN SE_NICLK_IO 0 CLK_B>;
+						DATA1 = <&pio14 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio14 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio13 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin2_serial: tsin2_serial {
+					st,pins {
+						DATA7 = <&pio13 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio13 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsin3 {
+				pinctrl_tsin3_serial: tsin3_serial {
+					st,pins {
+						DATA7 = <&pio14 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio14 0 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio13 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio13 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio13 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsin4 {
+				pinctrl_tsin4_serial_alt3: tsin4_serial_alt3 {
+					st,pins {
+						DATA7 = <&pio14 6 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio14 5 ALT3 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio14 3 ALT3 IN SE_NICLK_IO 0 CLK_B>;
+						ERROR = <&pio14 2 ALT3 IN SE_NICLK_IO 0 CLK_B>;
+						PKCLK = <&pio14 4 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsin5 {
+				pinctrl_tsin5_serial_alt1: tsin5_serial_alt1 {
+					st,pins {
+						DATA7 = <&pio18 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio18 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio18 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio18 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio18 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsin5_serial_alt2: tsin5_serial_alt2 {
+					st,pins {
+						DATA7 = <&pio19 4 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio19 3 ALT2 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio19 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio19 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio19 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsout0 {
+				pinctrl_tsout0_parallel: tsout0_parallel {
+					st,pins {
+						DATA7 = <&pio12 0 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio12 1 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio12 2 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio12 3 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio12 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio12 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio12 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio12 7 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT3 OUT NICLK 0 CLK_A>;
+						VALID = <&pio11 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+				pinctrl_tsout0_serial: tsout0_serial {
+					st,pins {
+						DATA7 = <&pio12 0 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio11 7 ALT3 OUT NICLK 0 CLK_A>;
+						VALID = <&pio11 5 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio11 4 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio11 6 ALT3 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			tsout1 {
+				pinctrl_tsout1_serial: tsout1_serial {
+					st,pins {
+						DATA7 = <&pio19 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio19 3 ALT1 OUT NICLK 0 CLK_A>;
+						VALID = <&pio19 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio19 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio19 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			mtsin0 {
+				pinctrl_mtsin0_parallel: mtsin0_parallel {
+					st,pins {
+						DATA7 = <&pio10 4 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA6 = <&pio10 5 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA5 = <&pio10 6 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA4 = <&pio10 7 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA3 = <&pio11 0 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA2 = <&pio11 1 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA1 = <&pio11 2 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						DATA0 = <&pio11 3 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio10 3 ALT3 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio10 1 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio10 0 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio10 2 ALT3 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+
+			systrace {
+				pinctrl_systrace_default: systrace-default {
+					st,pins {
+						trc_data0 = <&pio11 3 ALT5 OUT>;
+						trc_data1 = <&pio11 4 ALT5 OUT>;
+						trc_data2 = <&pio11 5 ALT5 OUT>;
+						trc_data3 = <&pio11 6 ALT5 OUT>;
+						trc_clk   = <&pio11 7 ALT5 OUT>;
+					};
+				};
+			};
+		};
+
+		pin-controller-front1@921f080 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stih407-front-pinctrl";
+			st,syscfg = <&syscfg_front>;
+			reg = <0x0921f080 0x4>;
+			reg-names = "irqmux";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
+			ranges = <0 0x09210000 0x10000>;
+
+			pio20: pio@9210000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x100>;
+				st,bank-name = "PIO20";
+			};
+
+			tsin4 {
+				pinctrl_tsin4_serial_alt1: tsin4_serial_alt1 {
+					st,pins {
+						DATA7 = <&pio20 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						CLKIN = <&pio20 3 ALT1 IN CLKNOTDATA 0 CLK_A>;
+						VALID = <&pio20 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						ERROR = <&pio20 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						PKCLK = <&pio20 2 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+					};
+				};
+			};
+		};
+
+		pin-controller-rear@922f080 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stih407-rear-pinctrl";
+			st,syscfg = <&syscfg_rear>;
+			reg = <0x0922f080 0x4>;
+			reg-names = "irqmux";
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
+			ranges = <0 0x09220000 0x6000>;
+
+			pio30: gpio@9220000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x100>;
+				st,bank-name = "PIO30";
+			};
+			pio31: gpio@9221000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x100>;
+				st,bank-name = "PIO31";
+			};
+			pio32: gpio@9222000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x100>;
+				st,bank-name = "PIO32";
+			};
+			pio33: gpio@9223000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x100>;
+				st,bank-name = "PIO33";
+			};
+			pio34: gpio@9224000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x100>;
+				st,bank-name = "PIO34";
+			};
+			pio35: gpio@9225000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x100>;
+				st,bank-name = "PIO35";
+				st,retime-pin-mask = <0x7f>;
+			};
+
+			i2c4 {
+				pinctrl_i2c4_default: i2c4-default {
+					st,pins {
+						sda = <&pio30 1 ALT1 BIDIR>;
+						scl = <&pio30 0 ALT1 BIDIR>;
+					};
+				};
+			};
+
+			i2c5 {
+				pinctrl_i2c5_default: i2c5-default {
+					st,pins {
+						sda = <&pio34 4 ALT1 BIDIR>;
+						scl = <&pio34 3 ALT1 BIDIR>;
+					};
+				};
+			};
+
+			usb3 {
+				pinctrl_usb3: usb3-2 {
+					st,pins {
+						usb-oc-detect = <&pio35 4 ALT1 IN>;
+						usb-pwr-enable = <&pio35 5 ALT1 OUT>;
+						usb-vbus-valid = <&pio35 6 ALT1 IN>;
+					};
+				};
+			};
+
+			pwm0 {
+				pinctrl_pwm0_chan0_default: pwm0-0-default {
+					st,pins {
+						pwm-capturein = <&pio31 0 ALT1 IN>;
+						pwm-out = <&pio31 1 ALT1 OUT>;
+					};
+				};
+			};
+
+			spi4 {
+				pinctrl_spi4_default: spi4-4w-alt1-0 {
+					st,pins {
+						mtsr = <&pio30 1 ALT1 OUT>;
+						mrst = <&pio30 2 ALT1 IN>;
+						scl = <&pio30 0 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi4_3w_alt1_0: spi4-3w-alt1-0 {
+					st,pins {
+						mtsr = <&pio30 1 ALT1 BIDIR_PU>;
+						scl = <&pio30 0 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_spi4_4w_alt3_0: spi4-4w-alt3-0 {
+					st,pins {
+						mtsr = <&pio34 1 ALT3 OUT>;
+						mrst = <&pio34 2 ALT3 IN>;
+						scl = <&pio34 0 ALT3 OUT>;
+					};
+				};
+
+				pinctrl_spi4_3w_alt3_0: spi4-3w-alt3-0 {
+					st,pins {
+						mtsr = <&pio34 1 ALT3 BIDIR_PU>;
+						scl = <&pio34 0 ALT3 OUT>;
+					};
+				};
+			};
+
+			i2s_out {
+				pinctrl_i2s_8ch_out: i2s_8ch_out{
+					st,pins {
+						mclk = <&pio33 5 ALT1 OUT>;
+						lrclk = <&pio33 7 ALT1 OUT>;
+						sclk = <&pio33 6 ALT1 OUT>;
+						data0 = <&pio33 4 ALT1 OUT>;
+						data1 = <&pio34 0 ALT1 OUT>;
+						data2 = <&pio34 1 ALT1 OUT>;
+						data3 = <&pio34 2 ALT1 OUT>;
+					};
+				};
+
+				pinctrl_i2s_2ch_out: i2s_2ch_out{
+					st,pins {
+						mclk = <&pio33 5 ALT1 OUT>;
+						lrclk = <&pio33 7 ALT1 OUT>;
+						sclk = <&pio33 6 ALT1 OUT>;
+						data0 = <&pio33 4 ALT1 OUT>;
+					};
+				};
+			};
+
+			i2s_in {
+				pinctrl_i2s_8ch_in: i2s_8ch_in{
+					st,pins {
+						mclk = <&pio32 5 ALT1 IN>;
+						lrclk = <&pio32 7 ALT1 IN>;
+						sclk = <&pio32 6 ALT1 IN>;
+						data0 = <&pio32 4 ALT1 IN>;
+						data1 = <&pio33 0 ALT1 IN>;
+						data2 = <&pio33 1 ALT1 IN>;
+						data3 = <&pio33 2 ALT1 IN>;
+						data4 = <&pio33 3 ALT1 IN>;
+					};
+				};
+
+				pinctrl_i2s_2ch_in: i2s_2ch_in{
+					st,pins {
+						mclk = <&pio32 5 ALT1 IN>;
+						lrclk = <&pio32 7 ALT1 IN>;
+						sclk = <&pio32 6 ALT1 IN>;
+						data0 = <&pio32 4 ALT1 IN>;
+					};
+				};
+			};
+
+			spdif_out {
+				pinctrl_spdif_out: spdif_out{
+					st,pins {
+						spdif_out = <&pio34 7 ALT1 OUT>;
+					};
+				};
+			};
+
+			serial3 {
+				pinctrl_serial3: serial3-0 {
+					st,pins {
+						tx = <&pio31 3 ALT1 OUT>;
+						rx = <&pio31 4 ALT1 IN>;
+					};
+				};
+			};
+		};
+
+		pin-controller-flash@923f080 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stih407-flash-pinctrl";
+			st,syscfg = <&syscfg_flash>;
+			reg = <0x0923f080 0x4>;
+			reg-names = "irqmux";
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "irqmux";
+			ranges = <0 0x09230000 0x3000>;
+
+			pio40: gpio@9230000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x100>;
+				st,bank-name = "PIO40";
+			};
+			pio41: gpio@9231000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x100>;
+				st,bank-name = "PIO41";
+			};
+			pio42: gpio@9232000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x100>;
+				st,bank-name = "PIO42";
+			};
+
+			mmc0 {
+				pinctrl_mmc0: mmc0-0 {
+					st,pins {
+						emmc_clk = <&pio40 6 ALT1 BIDIR>;
+						emmc_cmd = <&pio40 7 ALT1 BIDIR_PU>;
+						emmc_d0 = <&pio41 0 ALT1 BIDIR_PU>;
+						emmc_d1 = <&pio41 1 ALT1 BIDIR_PU>;
+						emmc_d2 = <&pio41 2 ALT1 BIDIR_PU>;
+						emmc_d3 = <&pio41 3 ALT1 BIDIR_PU>;
+						emmc_d4 = <&pio41 4 ALT1 BIDIR_PU>;
+						emmc_d5 = <&pio41 5 ALT1 BIDIR_PU>;
+						emmc_d6 = <&pio41 6 ALT1 BIDIR_PU>;
+						emmc_d7 = <&pio41 7 ALT1 BIDIR_PU>;
+					};
+				};
+				pinctrl_sd0: sd0-0 {
+					st,pins {
+						sd_clk = <&pio40 6 ALT1 BIDIR>;
+						sd_cmd = <&pio40 7 ALT1 BIDIR_PU>;
+						sd_dat0 = <&pio41 0 ALT1 BIDIR_PU>;
+						sd_dat1 = <&pio41 1 ALT1 BIDIR_PU>;
+						sd_dat2 = <&pio41 2 ALT1 BIDIR_PU>;
+						sd_dat3 = <&pio41 3 ALT1 BIDIR_PU>;
+						sd_led = <&pio42 0 ALT2 OUT>;
+						sd_pwren = <&pio42 2 ALT2 OUT>;
+						sd_vsel = <&pio42 3 ALT2 OUT>;
+						sd_cd = <&pio42 4 ALT2 IN>;
+						sd_wp = <&pio42 5 ALT2 IN>;
+					};
+				};
+			};
+
+			fsm {
+				pinctrl_fsm: fsm {
+					st,pins {
+						spi-fsm-clk = <&pio40 1 ALT1 OUT>;
+						spi-fsm-cs = <&pio40 0 ALT1 OUT>;
+						spi-fsm-mosi = <&pio40 2 ALT1 OUT>;
+						spi-fsm-miso = <&pio40 3 ALT1 IN>;
+						spi-fsm-hol = <&pio40 5 ALT1 OUT>;
+						spi-fsm-wp = <&pio40 4 ALT1 OUT>;
+					};
+				};
+			};
+
+			nand {
+				pinctrl_nand: nand {
+					st,pins {
+						nand_cs1 = <&pio40 6 ALT3 OUT>;
+						nand_cs0 = <&pio40 7 ALT3 OUT>;
+						nand_d0 = <&pio41 0 ALT3 BIDIR>;
+						nand_d1 = <&pio41 1 ALT3 BIDIR>;
+						nand_d2 = <&pio41 2 ALT3 BIDIR>;
+						nand_d3 = <&pio41 3 ALT3 BIDIR>;
+						nand_d4 = <&pio41 4 ALT3 BIDIR>;
+						nand_d5 = <&pio41 5 ALT3 BIDIR>;
+						nand_d6 = <&pio41 6 ALT3 BIDIR>;
+						nand_d7 = <&pio41 7 ALT3 BIDIR>;
+						nand_we = <&pio42 0 ALT3 OUT>;
+						nand_dqs = <&pio42 1 ALT3 OUT>;
+						nand_ale = <&pio42 2 ALT3 OUT>;
+						nand_cle = <&pio42 3 ALT3 OUT>;
+						nand_rnb = <&pio42 4 ALT3 IN>;
+						nand_oe = <&pio42 5 ALT3 OUT>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih407.dtsi b/arch/arm/boot/dts/st/stih407.dtsi
new file mode 100644
index 000000000000..aca43d2bdaad
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih407.dtsi
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 STMicroelectronics Limited.
+ * Author: Gabriel Fernandez <gabriel.fernandez@linaro.org>
+ */
+#include "stih407-clock.dtsi"
+#include "stih407-family.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	soc {
+		sti-display-subsystem@0 {
+			compatible = "st,sti-display-subsystem";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0>;
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
+					  <&clk_s_d2_quadfs 1>,
+					  <&clk_s_c0_pll1 0>,
+					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					  <&clk_s_c0_flexgen CLK_MAIN_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_AUX_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP1>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP2>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP3>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP4>;
+
+			assigned-clock-parents = <0>,
+						 <0>,
+						 <0>,
+						 <&clk_s_c0_pll1 0>,
+						 <&clk_s_c0_pll1 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 1>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>;
+
+			assigned-clock-rates = <297000000>,
+					       <108000000>,
+					       <0>,
+					       <400000000>,
+					       <400000000>;
+
+			ranges;
+
+			sti-compositor@9d11000 {
+				compatible = "st,stih407-compositor";
+				reg = <0x9d11000 0x1000>;
+
+				clock-names = "compo_main",
+					      "compo_aux",
+					      "pix_main",
+					      "pix_aux",
+					      "pix_gdp1",
+					      "pix_gdp2",
+					      "pix_gdp3",
+					      "pix_gdp4",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					 <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					 <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>,
+					 <&clk_s_d2_flexgen CLK_PIX_AUX_DISP>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP1>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP2>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP3>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP4>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				reset-names = "compo-main", "compo-aux";
+				resets = <&softreset STIH407_COMPO_SOFTRESET>,
+					 <&softreset STIH407_COMPO_SOFTRESET>;
+				st,vtg = <&vtg_main>, <&vtg_aux>;
+			};
+
+			sti-tvout@8d08000 {
+				compatible = "st,stih407-tvout";
+				reg = <0x8d08000 0x1000>;
+				reg-names = "tvout-reg";
+				reset-names = "tvout";
+				resets = <&softreset STIH407_HDTVOUT_SOFTRESET>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				assigned-clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+						  <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+						  <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+						  <&clk_s_d0_flexgen CLK_PCM_0>,
+						  <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+						  <&clk_s_d2_flexgen CLK_HDDAC>;
+
+				assigned-clock-parents = <&clk_s_d2_quadfs 0>,
+							 <&clk_tmdsout_hdmi>,
+							 <&clk_s_d2_quadfs 0>,
+							 <&clk_s_d0_quadfs 0>,
+							 <&clk_s_d2_quadfs 0>,
+							 <&clk_s_d2_quadfs 0>;
+			};
+
+			sti_hdmi: sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				#sound-dai-cells = <0>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3 GPIO_ACTIVE_LOW>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih410-b2120.dts b/arch/arm/boot/dts/st/stih410-b2120.dts
new file mode 100644
index 000000000000..538ff98ca1b1
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410-b2120.dts
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics (R&D) Limited.
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ */
+/dts-v1/;
+#include "stih410.dtsi"
+#include "stihxxx-b2120.dtsi"
+/ {
+	model = "STiH410 B2120";
+	compatible = "st,stih410-b2120", "st,stih410";
+
+	chosen {
+		stdout-path = &sbc_serial0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x80000000>;
+	};
+
+	aliases {
+		serial0 = &sbc_serial0;
+		ethernet0 = &ethernet0;
+	};
+
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
+	soc {
+
+		mmc0: sdhci@9060000 {
+			max-frequency = <200000000>;
+			sd-uhs-sdr50;
+			sd-uhs-sdr104;
+			sd-uhs-ddr50;
+		};
+
+		ohci0: usb@9a03c00 {
+			status = "okay";
+		};
+
+		ehci0: usb@9a03e00 {
+			status = "okay";
+		};
+
+		ohci1: usb@9a83c00 {
+			status = "okay";
+		};
+
+		ehci1: usb@9a83e00 {
+			status = "okay";
+		};
+
+		sti-display-subsystem@0 {
+			sti-hda@8d02000 {
+				status = "okay";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih410-b2260.dts b/arch/arm/boot/dts/st/stih410-b2260.dts
new file mode 100644
index 000000000000..240b62040000
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410-b2260.dts
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2016 STMicroelectronics (R&D) Limited.
+ * Author: Patrice Chotard <patrice.chotard@st.com>
+ */
+/dts-v1/;
+#include "stih410.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "STiH410 B2260";
+	compatible = "st,stih410-b2260", "st,stih410";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x40000000>;
+	};
+
+	aliases {
+		serial1 = &uart1;
+		ethernet0 = &ethernet0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-user-green-1 {
+			label = "User_green_1";
+			gpios = <&pio1 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led-user-green-2 {
+			label = "User_green_2";
+			gpios = <&pio4 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-user-green-3 {
+			label = "User_green_3";
+			gpios = <&pio2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-user-green-4 {
+			label = "User_green_4";
+			gpios = <&pio2 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "STI-B2260";
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			/* DAC */
+			format = "i2s";
+			mclk-fs = <128>;
+			cpu {
+				sound-dai = <&sti_uni_player0>;
+			};
+
+			codec {
+				sound-dai = <&sti_hdmi>;
+			};
+		};
+	};
+
+	miphy28lp_phy: miphy28lp {
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
+	soc {
+		/* Low speed expansion connector */
+		uart0: serial@9830000 {
+			label = "LS-UART0";
+			pinctrl-names = "default", "no-hw-flowctrl";
+			pinctrl-0 = <&pinctrl_serial0_hw_flowctrl>;
+			pinctrl-1 = <&pinctrl_serial0>;
+			rts-gpios = <&pio17 3 GPIO_ACTIVE_LOW>;
+			uart-has-rtscts;
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		uart1: serial@9831000 {
+			label = "LS-UART1";
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		spi0: spi@9844000 {
+			label = "LS-SPI0";
+			cs-gpios = <&pio30 3 0>;
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		i2c0: i2c@9840000 {
+			label = "LS-I2C0";
+			status = "okay";
+		};
+
+		/* Low speed expansion connector */
+		i2c1: i2c@9841000 {
+			label = "LS-I2C1";
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		i2c2: i2c@9842000 {
+			label = "HS-I2C2";
+			pinctrl-0 = <&pinctrl_i2c2_alt2_1>;
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		i2c3: i2c@9843000 {
+			label = "HS-I2C3";
+			pinctrl-0 = <&pinctrl_i2c3_alt3_0>;
+			status = "okay";
+		};
+
+		mmc0: sdhci@9060000 {
+			pinctrl-0 = <&pinctrl_sd0>;
+			bus-width = <4>;
+			status = "okay";
+		};
+
+		/* high speed expansion connector */
+		mmc1: sdhci@9080000 {
+			status = "okay";
+		};
+
+		pwm0: pwm@9810000 {
+			status = "okay";
+		};
+
+		pwm1: pwm@9510000 {
+			status = "okay";
+		};
+
+		ohci0: usb@9a03c00 {
+			status = "okay";
+		};
+
+		ehci0: usb@9a03e00 {
+			status = "okay";
+		};
+
+		ohci1: usb@9a83c00 {
+			status = "okay";
+		};
+
+		ehci1: usb@9a83e00 {
+			status = "okay";
+		};
+
+		st_dwc3: dwc3@8f94000 {
+			status = "okay";
+		};
+
+		ethernet0: dwmac@9630000 {
+			phy-mode = "rgmii";
+			pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
+
+			snps,reset-gpio = <&pio0 7 0>;
+			snps,reset-active-low;
+			snps,reset-delays-us = <0 10000 1000000>;
+
+			status = "okay";
+		};
+
+		sti_uni_player0: sti-uni-player@8d80000 {
+			status = "okay";
+		};
+		/* SSC11 to HDMI */
+		hdmiddc: i2c@9541000 {
+			/* HDMI V1.3a supports Standard mode only */
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+			status = "okay";
+		};
+
+		sata1: sata@9b28000 {
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih410-clock.dtsi b/arch/arm/boot/dts/st/stih410-clock.dtsi
new file mode 100644
index 000000000000..abac98a1810b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410-clock.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih410-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+		clock-output-names = "CLK_SYSIN";
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		compatible = "st,stih410-clk", "simple-bus";
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih407-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			/*
+			 * ARM CPU related clocks.
+			 */
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih410-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih410-pinctrl.dtsi b/arch/arm/boot/dts/st/stih410-pinctrl.dtsi
new file mode 100644
index 000000000000..e6eadd124416
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410-pinctrl.dtsi
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics Limited.
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ */
+#include "st-pincfg.h"
+/ {
+
+	soc {
+		pin-controller-rear@922f080 {
+
+			usb0 {
+				pinctrl_usb0: usb2-0 {
+					st,pins {
+						usb-oc-detect = <&pio35 0 ALT1 IN>;
+						usb-pwr-enable = <&pio35 1 ALT1 OUT>;
+					};
+				};
+			};
+
+			usb1 {
+				pinctrl_usb1: usb2-1 {
+					st,pins {
+						usb-oc-detect = <&pio35 2 ALT1 IN>;
+						usb-pwr-enable = <&pio35 3 ALT1 OUT>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih410.dtsi b/arch/arm/boot/dts/st/stih410.dtsi
new file mode 100644
index 000000000000..29e95e9d3229
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih410.dtsi
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics Limited.
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ */
+#include "stih410-clock.dtsi"
+#include "stih407-family.dtsi"
+#include "stih410-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	aliases {
+		bdisp0 = &bdisp0;
+	};
+
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+
+		status = "disabled";
+	};
+
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
+
+		status = "disabled";
+	};
+
+	soc {
+		ohci0: usb@9a03c00 {
+			compatible = "st,st-ohci-300x";
+			reg = <0x9a03c00 0x100>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy1>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ehci0: usb@9a03e00 {
+			compatible = "st,st-ehci-300x";
+			reg = <0x9a03e00 0x100>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy1>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci1: usb@9a83c00 {
+			compatible = "st,st-ohci-300x";
+			reg = <0x9a83c00 0x100>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy2>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ehci1: usb@9a83e00 {
+			compatible = "st,st-ehci-300x";
+			reg = <0x9a83e00 0x100>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb1>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>,
+				 <&clk_s_c0_flexgen CLK_RX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy2>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		sti-display-subsystem@0 {
+			compatible = "st,sti-display-subsystem";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			reg = <0 0>;
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
+					  <&clk_s_d2_quadfs 1>,
+					  <&clk_s_c0_pll1 0>,
+					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					  <&clk_s_c0_flexgen CLK_MAIN_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_AUX_DISP>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP1>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP2>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP3>,
+					  <&clk_s_d2_flexgen CLK_PIX_GDP4>;
+
+			assigned-clock-parents = <0>,
+						 <0>,
+						 <0>,
+						 <&clk_s_c0_pll1 0>,
+						 <&clk_s_c0_pll1 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 1>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>,
+						 <&clk_s_d2_quadfs 0>;
+
+			assigned-clock-rates = <297000000>,
+					       <297000000>,
+					       <0>,
+					       <400000000>,
+					       <400000000>;
+
+			ranges;
+
+			sti-compositor@9d11000 {
+				compatible = "st,stih407-compositor";
+				reg = <0x9d11000 0x1000>;
+
+				clock-names = "compo_main",
+					      "compo_aux",
+					      "pix_main",
+					      "pix_aux",
+					      "pix_gdp1",
+					      "pix_gdp2",
+					      "pix_gdp3",
+					      "pix_gdp4",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					 <&clk_s_c0_flexgen CLK_COMPO_DVP>,
+					 <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>,
+					 <&clk_s_d2_flexgen CLK_PIX_AUX_DISP>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP1>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP2>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP3>,
+					 <&clk_s_d2_flexgen CLK_PIX_GDP4>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				reset-names = "compo-main", "compo-aux";
+				resets = <&softreset STIH407_COMPO_SOFTRESET>,
+					 <&softreset STIH407_COMPO_SOFTRESET>;
+				st,vtg = <&vtg_main>, <&vtg_aux>;
+			};
+
+			sti-tvout@8d08000 {
+				compatible = "st,stih407-tvout";
+				reg = <0x8d08000 0x1000>;
+				reg-names = "tvout-reg";
+				reset-names = "tvout";
+				resets = <&softreset STIH407_HDTVOUT_SOFTRESET>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				assigned-clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+						  <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+						  <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+						  <&clk_s_d0_flexgen CLK_PCM_0>,
+						  <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+						  <&clk_s_d2_flexgen CLK_HDDAC>;
+
+				assigned-clock-parents = <&clk_s_d2_quadfs 0>,
+							 <&clk_tmdsout_hdmi>,
+							 <&clk_s_d2_quadfs 0>,
+							 <&clk_s_d0_quadfs 0>,
+							 <&clk_s_d2_quadfs 0>,
+							 <&clk_s_d2_quadfs 0>;
+			};
+
+			sti_hdmi: sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				#sound-dai-cells = <0>;
+				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3 GPIO_ACTIVE_LOW>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				status = "disabled";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+			};
+
+			sti-hqvdp@9c00000 {
+				compatible = "st,stih407-hqvdp";
+				reg = <0x9C00000 0x100000>;
+				clock-names = "hqvdp", "pix_main";
+				clocks = <&clk_s_c0_flexgen CLK_MAIN_DISP>,
+					 <&clk_s_d2_flexgen CLK_PIX_MAIN_DISP>;
+				reset-names = "hqvdp";
+				resets = <&softreset STIH407_HDQVDP_SOFTRESET>;
+				st,vtg = <&vtg_main>;
+			};
+		};
+
+		bdisp0:bdisp@9f10000 {
+			compatible = "st,stih407-bdisp";
+			reg = <0x9f10000 0x1000>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "bdisp";
+			clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>;
+		};
+
+		hva@8c85000 {
+			compatible = "st,st-hva";
+			reg = <0x8c85000 0x400>, <0x6000000 0x40000>;
+			reg-names = "hva_registers", "hva_esram";
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "clk_hva";
+			clocks = <&clk_s_c0_flexgen CLK_HVA>;
+		};
+
+		thermal@91a0000 {
+			compatible = "st,stih407-thermal";
+			reg = <0x91a0000 0x28>;
+			clock-names = "thermal";
+			clocks = <&clk_sysin>;
+			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		cec@94a087c {
+			compatible = "st,stih-cec";
+			reg = <0x94a087c 0x64>;
+			clocks = <&clk_sysin>;
+			clock-names = "cec-clk";
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cec-irq";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_cec0_default>;
+			resets = <&softreset STIH407_LPM_SOFTRESET>;
+			hdmi-phandle = <&sti_hdmi>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih418-b2199.dts b/arch/arm/boot/dts/st/stih418-b2199.dts
new file mode 100644
index 000000000000..53ac6c2b7b7d
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418-b2199.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 STMicroelectronics (R&D) Limited.
+ * Author: Maxime Coquelin <maxime.coquelin@st.com>
+ */
+/dts-v1/;
+#include "stih418.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	model = "STiH418 B2199";
+	compatible = "st,stih418-b2199", "st,stih418";
+
+	chosen {
+		stdout-path = &sbc_serial0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0xc0000000>;
+	};
+
+	aliases {
+		serial0 = &sbc_serial0;
+		ethernet0 = &ethernet0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			label = "Front Panel LED";
+			gpios = <&pio4 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-green {
+			gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
+	soc {
+		sbc_serial0: serial@9530000 {
+			status = "okay";
+		};
+
+		i2c@9842000 {
+			status = "okay";
+		};
+
+		i2c@9843000 {
+			status = "okay";
+		};
+
+		i2c@9844000 {
+			status = "okay";
+		};
+
+		i2c@9845000 {
+			status = "okay";
+		};
+
+		i2c@9540000 {
+			status = "okay";
+		};
+
+		/* SSC11 to HDMI */
+		i2c@9541000 {
+			status = "okay";
+			/* HDMI V1.3a supports Standard mode only */
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+		};
+
+		mmc1: sdhci@9080000 {
+			status = "okay";
+		};
+
+		mmc0: sdhci@9060000 {
+			status = "okay";
+			max-frequency = <200000000>;
+			sd-uhs-sdr50;
+			sd-uhs-sdr104;
+			sd-uhs-ddr50;
+			non-removable;
+		};
+
+		st_dwc3: dwc3@8f94000 {
+			status = "okay";
+		};
+
+		ethernet0: dwmac@9630000 {
+			st,tx-retime-src = "clkgen";
+			status = "okay";
+			phy-mode = "rgmii";
+			fixed-link = <0 1 1000 0 0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih418-b2264.dts b/arch/arm/boot/dts/st/stih418-b2264.dts
new file mode 100644
index 000000000000..fc32a03073b6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418-b2264.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 STMicroelectronics
+ * Author: Alain Volmat <avolmat@me.com>
+ */
+/dts-v1/;
+#include "stih418.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+/ {
+	model = "STiH418 B2264";
+	compatible = "st,stih418-b2264", "st,stih418";
+
+	chosen {
+		stdout-path = &sbc_serial0;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0xc0000000>;
+	};
+
+	cpus {
+		cpu@0 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@1 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@2 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+		cpu@3 {
+			operating-points-v2 = <&cpu_opp_table>;
+			/* u-boot puts hpen in SBC dmem at 0xb8 offset */
+			cpu-release-addr = <0x94100b8>;
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <784000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <784000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <784000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <784000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <1500000000>;
+			opp-microvolt = <784000>;
+		};
+	};
+
+	aliases {
+		ttyAS0 = &sbc_serial0;
+		ethernet0 = &ethernet0;
+	};
+
+	soc {
+		leds {
+			compatible = "gpio-leds";
+			led-green {
+				gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+		pin-controller-sbc@961f080 {
+			gmac1 {
+				rgmii1-0 {
+					st,pins {
+						rxd0 = <&pio1 4 ALT1 IN DE_IO 300 CLK_A>;
+						rxd1 = <&pio1 5 ALT1 IN DE_IO 300 CLK_A>;
+						rxd2 = <&pio1 6 ALT1 IN DE_IO 300 CLK_A>;
+						rxd3 = <&pio1 7 ALT1 IN DE_IO 300 CLK_A>;
+						rxdv = <&pio2 0 ALT1 IN DE_IO 300 CLK_A>;
+					};
+				};
+			};
+		};
+
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ethernet0 {
+	phy-mode = "rgmii";
+	pinctrl-0 = <&pinctrl_rgmii1 &pinctrl_rgmii1_mdio_1>;
+	st,tx-retime-src = "clkgen";
+
+	snps,reset-gpio = <&pio0 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+
+	status = "okay";
+};
+
+&miphy28lp_phy {
+	phy_port0: port@9b22000 {
+		st,sata-gen = <2>; /* SATA GEN3 */
+		st,osc-rdy;
+	};
+};
+
+&mmc0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sata0 {
+	status = "okay";
+};
+
+&sbc_serial0 {
+	status = "okay";
+};
+
+&spifsm {
+	status = "okay";
+};
+
+&st_dwc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stih418-clock.dtsi b/arch/arm/boot/dts/st/stih418-clock.dtsi
new file mode 100644
index 000000000000..e1749e92a2e7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418-clock.dtsi
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 STMicroelectronics R&D Limited
+ */
+#include <dt-bindings/clock/stih418-clks.h>
+/ {
+	/*
+	 * Fixed 30MHz oscillator inputs to SoC
+	 */
+	clk_sysin: clk-sysin {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <30000000>;
+		clock-output-names = "CLK_SYSIN";
+	};
+
+	clk_tmdsout_hdmi: clk-tmdsout-hdmi {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		compatible = "st,stih418-clk", "simple-bus";
+
+		/*
+		 * A9 PLL.
+		 */
+		clockgen-a9@92b0000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x92b0000 0x10000>;
+
+			clockgen_a9_pll: clockgen-a9-pll {
+				#clock-cells = <1>;
+				compatible = "st,stih418-clkgen-plla9";
+
+				clocks = <&clk_sysin>;
+			};
+
+			/*
+			 * ARM CPU related clocks.
+			 */
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-a@90ff000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x90ff000 0x1000>;
+
+			clk_s_a0_pll: clk-s-a0-pll {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-a0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_a0_flexgen: clk-s-a0-flexgen {
+				compatible = "st,flexgen", "st,flexgen-stih410-a0";
+
+				#clock-cells = <1>;
+
+				clocks = <&clk_s_a0_pll 0>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clk_s_c0: clockgen-c@9103000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9103000 0x1000>;
+
+			clk_s_c0_pll0: clk-s-c0-pll0 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll0-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_pll1: clk-s-c0-pll1 {
+				#clock-cells = <1>;
+				compatible = "st,clkgen-pll1-c0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_c0_flexgen: clk-s-c0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih418-c0";
+
+				clocks = <&clk_s_c0_pll0 0>,
+					 <&clk_s_c0_pll1 0>,
+					 <&clk_s_c0_quadfs 0>,
+					 <&clk_s_c0_quadfs 1>,
+					 <&clk_s_c0_quadfs 2>,
+					 <&clk_s_c0_quadfs 3>,
+					 <&clk_sysin>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				clk_m_a9_ext2f_div2: clk-m-a9-ext2f-div2s {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+
+					clocks = <&clk_s_c0_flexgen 13>;
+
+					clock-output-names = "clk-m-a9-ext2f-div2";
+
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
+			};
+		};
+
+		clockgen-d0@9104000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9104000 0x1000>;
+
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d0_flexgen: clk-s-d0-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih410-d0";
+
+				clocks = <&clk_s_d0_quadfs 0>,
+					 <&clk_s_d0_quadfs 1>,
+					 <&clk_s_d0_quadfs 2>,
+					 <&clk_s_d0_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+
+		clockgen-d2@9106000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9106000 0x1000>;
+
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d2_flexgen: clk-s-d2-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih418-d2";
+
+				clocks = <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>,
+					 <&clk_s_d2_quadfs 2>,
+					 <&clk_s_d2_quadfs 3>,
+					 <&clk_sysin>,
+					 <&clk_sysin>,
+					 <&clk_tmdsout_hdmi>;
+			};
+		};
+
+		clockgen-d3@9107000 {
+			compatible = "st,clkgen-c32";
+			reg = <0x9107000 0x1000>;
+
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
+			clk_s_d3_flexgen: clk-s-d3-flexgen {
+				#clock-cells = <1>;
+				compatible = "st,flexgen", "st,flexgen-stih407-d3";
+
+				clocks = <&clk_s_d3_quadfs 0>,
+					 <&clk_s_d3_quadfs 1>,
+					 <&clk_s_d3_quadfs 2>,
+					 <&clk_s_d3_quadfs 3>,
+					 <&clk_sysin>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stih418.dtsi b/arch/arm/boot/dts/st/stih418.dtsi
new file mode 100644
index 000000000000..b35b9b7a7ccc
--- /dev/null
+++ b/arch/arm/boot/dts/st/stih418.dtsi
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics Limited.
+ * Author: Peter Griffin <peter.griffin@linaro.org>
+ */
+#include "stih418-clock.dtsi"
+#include "stih407-family.dtsi"
+#include "stih410-pinctrl.dtsi"
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <2>;
+			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
+			cpu-release-addr = <0x94100A4>;
+		};
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <3>;
+			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
+			cpu-release-addr = <0x94100A4>;
+		};
+	};
+
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+	};
+
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
+	};
+
+	soc {
+		rng11: rng@8a8a000 {
+			status = "disabled";
+		};
+
+		ohci0: usb@9a03c00 {
+			compatible = "st,st-ohci-300x";
+			reg = <0x9a03c00 0x100>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy1>;
+			phy-names = "usb";
+		};
+
+		ehci0: usb@9a03e00 {
+			compatible = "st,st-ehci-300x";
+			reg = <0x9a03e00 0x100>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb0>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT0_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT0_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy1>;
+			phy-names = "usb";
+		};
+
+		ohci1: usb@9a83c00 {
+			compatible = "st,st-ohci-300x";
+			reg = <0x9a83c00 0x100>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy2>;
+			phy-names = "usb";
+		};
+
+		ehci1: usb@9a83e00 {
+			compatible = "st,st-ehci-300x";
+			reg = <0x9a83e00 0x100>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb1>;
+			clocks = <&clk_s_c0_flexgen CLK_TX_ICN_DISP_0>;
+			resets = <&powerdown STIH407_USB2_PORT1_POWERDOWN>,
+				 <&softreset STIH407_USB2_PORT1_SOFTRESET>;
+			reset-names = "power", "softreset";
+			phys = <&usb2_picophy2>;
+			phy-names = "usb";
+		};
+
+		mmc0: sdhci@9060000 {
+			assigned-clocks = <&clk_s_c0_flexgen CLK_MMC_0>;
+			assigned-clock-parents = <&clk_s_c0_pll1 0>;
+			assigned-clock-rates = <200000000>;
+		};
+
+		thermal@91a0000 {
+			compatible = "st,stih407-thermal";
+			reg = <0x91a0000 0x28>;
+			clock-names = "thermal";
+			clocks = <&clk_sysin>;
+			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stihxxx-b2120.dtsi b/arch/arm/boot/dts/st/stihxxx-b2120.dtsi
new file mode 100644
index 000000000000..8d9a2dfa76f1
--- /dev/null
+++ b/arch/arm/boot/dts/st/stihxxx-b2120.dtsi
@@ -0,0 +1,206 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics (R&D) Limited.
+ * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
+ */
+#include <dt-bindings/clock/stih407-clks.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/c8sectpfe.h>
+/ {
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			label = "Front Panel LED";
+			gpios = <&pio4 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-green {
+			gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "STI-B2120";
+		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			/* HDMI */
+			format = "i2s";
+			mclk-fs = <128>;
+			cpu {
+				sound-dai = <&sti_uni_player0>;
+			};
+
+			codec {
+				sound-dai = <&sti_hdmi>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			reg = <1>;
+			/* DAC */
+			format = "i2s";
+			mclk-fs = <256>;
+			frame-inversion;
+			cpu {
+				sound-dai = <&sti_uni_player2>;
+			};
+
+			codec {
+				sound-dai = <&sti_sasg_codec 1>;
+			};
+		};
+
+		simple-audio-card,dai-link@2 {
+			reg = <2>;
+			/* SPDIF */
+			format = "left_j";
+			mclk-fs = <128>;
+			cpu {
+				sound-dai = <&sti_uni_player3>;
+			};
+
+			codec {
+				sound-dai = <&sti_sasg_codec 0>;
+			};
+		};
+	};
+
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
+	soc {
+		sbc_serial0: serial@9530000 {
+			status = "okay";
+		};
+
+		pwm0: pwm@9810000 {
+			status = "okay";
+		};
+
+		pwm1: pwm@9510000 {
+			status = "okay";
+		};
+
+		ssc2: i2c@9842000 {
+			status = "okay";
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+		};
+
+		ssc3: i2c@9843000 {
+			status = "okay";
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+		};
+
+		i2c@9844000 {
+			status = "okay";
+		};
+
+		i2c@9845000 {
+			status = "okay";
+		};
+
+		i2c@9540000 {
+			status = "okay";
+		};
+
+		mmc0: sdhci@9060000 {
+			non-removable;
+			status = "okay";
+		};
+
+		mmc1: sdhci@9080000 {
+			status = "okay";
+		};
+
+		/* SSC11 to HDMI */
+		hdmiddc: i2c@9541000 {
+			status = "okay";
+			/* HDMI V1.3a supports Standard mode only */
+			clock-frequency = <100000>;
+			st,i2c-min-scl-pulse-width-us = <0>;
+			st,i2c-min-sda-pulse-width-us = <5>;
+		};
+
+		st_dwc3: dwc3@8f94000 {
+			status = "okay";
+		};
+
+		ethernet0: dwmac@9630000 {
+			st,tx-retime-src = "clkgen";
+			status = "okay";
+			phy-mode = "rgmii";
+			fixed-link = <0 1 1000 0 0>;
+		};
+
+		demux@8a20000 {
+			compatible	= "st,stih407-c8sectpfe";
+			status		= "okay";
+			reg		= <0x08a20000 0x10000>,
+					  <0x08a00000 0x4000>;
+			reg-names	= "c8sectpfe", "c8sectpfe-ram";
+			interrupts	= <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+					  <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names	= "c8sectpfe-error-irq",
+					  "c8sectpfe-idle-irq";
+			pinctrl-0	= <&pinctrl_tsin0_serial>;
+			pinctrl-1	= <&pinctrl_tsin0_parallel>;
+			pinctrl-2	= <&pinctrl_tsin3_serial>;
+			pinctrl-3	= <&pinctrl_tsin4_serial_alt3>;
+			pinctrl-4	= <&pinctrl_tsin5_serial_alt1>;
+			pinctrl-names	= "tsin0-serial",
+					  "tsin0-parallel",
+					  "tsin3-serial",
+					  "tsin4-serial",
+					  "tsin5-serial";
+			clocks		= <&clk_s_c0_flexgen CLK_PROC_STFE>;
+			clock-names	= "c8sectpfe";
+
+			/* tsin0 is TSA on NIMA */
+			tsin0: port {
+				tsin-num = <0>;
+				serial-not-parallel;
+				i2c-bus = <&ssc2>;
+				reset-gpios = <&pio15 4 GPIO_ACTIVE_LOW>;
+				dvb-card = <STV0367_TDA18212_NIMA_1>;
+			};
+		};
+
+		sti_uni_player0: sti-uni-player@8d80000 {
+			status = "okay";
+		};
+
+		sti_uni_player2: sti-uni-player@8d82000 {
+			status = "okay";
+		};
+
+		sti_uni_player3: sti-uni-player@8d85000 {
+			status = "okay";
+		};
+
+		syscfg_core: core-syscfg@92b0000 {
+			sti_sasg_codec: sti-sasg-codec {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spdif_out>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32429i-eval.dts b/arch/arm/boot/dts/st/stm32429i-eval.dts
new file mode 100644
index 000000000000..576235ec3c51
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32429i-eval.dts
@@ -0,0 +1,337 @@
+/*
+ * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f429.dtsi"
+#include "stm32f429-pinctrl.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+/ {
+	model = "STMicroelectronics STM32429i-EVAL board";
+	compatible = "st,stm32429i-eval", "st,stm32f429";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	clocks {
+		clk_ext_camera: clk-ext-camera {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	soc {
+		dma-ranges = <0xc0000000 0x0 0x10000000>;
+	};
+
+	vdda: regulator-vdda {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vref: regulator-vref {
+		compatible = "regulator-fixed";
+		regulator-name = "vref";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vdd_panel: vdd-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-green {
+			gpios = <&gpiog 6 1>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-orange {
+			gpios = <&gpiog 7 1>;
+		};
+		led-red {
+			gpios = <&gpiog 10 1>;
+		};
+		led-blue {
+			gpios = <&gpiog 12 1>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "Wake up";
+			linux,code = <KEY_WAKEUP>;
+			gpios = <&gpioa 0 0>;
+		};
+		button-1 {
+			label = "Tamper";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpioc 13 0>;
+		};
+	};
+
+	usbotg_hs_phy: usbphy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc 0 STM32F4_AHB1_CLOCK(OTGHSULPI)>;
+		clock-names = "main_clk";
+	};
+
+	panel_rgb: panel-rgb {
+		compatible = "ampire,am-480272h3tmqw-t01h";
+		power-supply = <&vdd_panel>;
+		status = "okay";
+		port {
+			panel_in_rgb: endpoint {
+				remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
+
+	mmc_vcard: mmc_vcard {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcard";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc3_in8_pin>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vref>;
+	status = "okay";
+	adc3: adc@200 {
+		st,adc-channels = <8>;
+		status = "okay";
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&crc {
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+
+	port {
+		dcmi_0: endpoint {
+			remote-endpoint = <&ov2640_0>;
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+			bus-width = <8>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ov2640: camera@30 {
+		compatible = "ovti,ov2640";
+		reg = <0x30>;
+		resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>;
+		pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>;
+		clocks = <&clk_ext_camera>;
+		clock-names = "xvclk";
+		status = "okay";
+
+		port {
+			ov2640_0: endpoint {
+				remote-endpoint = <&dcmi_0>;
+			};
+		};
+	};
+
+	stmpe1600: stmpe1600@42 {
+		compatible = "st,stmpe1600";
+		reg = <0x42>;
+		interrupts = <8 3>;
+		interrupt-parent = <&gpioi>;
+		interrupt-controller;
+		wakeup-source;
+
+		stmpegpio: stmpe_gpio {
+			compatible = "st,stmpe-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+};
+
+&iwdg {
+	status = "okay";
+	timeout-sec = <32>;
+};
+
+&ltdc {
+	status = "okay";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-names = "default";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
+&mac {
+	status = "okay";
+	pinctrl-0 = <&ethernet_mii>;
+	pinctrl-names = "default";
+	phy-mode = "mii";
+	phy-handle = <&phy1>;
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdio {
+	status = "okay";
+	vmmc-supply = <&mmc_vcard>;
+	cd-gpios = <&stmpegpio 15 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default", "opendrain";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_pins_od>;
+	bus-width = <4>;
+	max-frequency = <12500000>;
+};
+
+&timers1 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm1_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm3_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32746g-eval.dts b/arch/arm/boot/dts/st/stm32746g-eval.dts
new file mode 100644
index 000000000000..a293e65141c6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32746g-eval.dts
@@ -0,0 +1,222 @@
+/*
+ * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f746.dtsi"
+#include "stm32f746-pinctrl.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "STMicroelectronics STM32746g-EVAL board";
+	compatible = "st,stm32746g-eval", "st,stm32f746";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x2000000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-green {
+			gpios = <&gpiof 10 1>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-orange {
+			gpios = <&stmfx_pinctrl 17 1>;
+		};
+		led-red {
+			gpios = <&gpiob 7 1>;
+		};
+		led-blue {
+			gpios = <&stmfx_pinctrl 19 1>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "Wake up";
+			linux,code = <KEY_WAKEUP>;
+			gpios = <&gpioc 13 0>;
+		};
+	};
+
+	joystick {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&joystick_pins>;
+		pinctrl-names = "default";
+		button-0 {
+			label = "JoySel";
+			linux,code = <KEY_ENTER>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		};
+		button-1 {
+			label = "JoyDown";
+			linux,code = <KEY_DOWN>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		};
+		button-2 {
+			label = "JoyLeft";
+			linux,code = <KEY_LEFT>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		};
+		button-3 {
+			label = "JoyRight";
+			linux,code = <KEY_RIGHT>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		};
+		button-4 {
+			label = "JoyUp";
+			linux,code = <KEY_UP>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+
+	usbotg_hs_phy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHSULPI)>;
+		clock-names = "main_clk";
+	};
+
+	mmc_vcard: mmc_vcard {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcard";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&crc {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-names = "default";
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	stmfx: stmfx@42 {
+		compatible = "st,stmfx-0300";
+		reg = <0x42>;
+		interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+		interrupt-parent = <&gpioi>;
+
+		stmfx_pinctrl: pinctrl {
+			compatible = "st,stmfx-0300-pinctrl";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+
+			joystick_pins: joystick {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
+				drive-push-pull;
+				bias-pull-up;
+			};
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdio1 {
+	status = "okay";
+	vmmc-supply = <&mmc_vcard>;
+	broken-cd;
+	pinctrl-names = "default", "opendrain";
+	pinctrl-0 = <&sdio_pins_a>;
+	pinctrl-1 = <&sdio_pins_od_a>;
+	bus-width = <4>;
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f4-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f4-pinctrl.dtsi
new file mode 100644
index 000000000000..3bb812d6399e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f4-pinctrl.dtsi
@@ -0,0 +1,482 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+#include <dt-bindings/mfd/stm32f4-rcc.h>
+
+/ {
+	soc {
+		pinctrl: pinctrl@40020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40020000 0x3000>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&syscfg 0x8>;
+
+			gpioa: gpio@40020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>;
+				st,bank-name = "GPIOA";
+			};
+
+			gpiob: gpio@40020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x400 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOB)>;
+				st,bank-name = "GPIOB";
+			};
+
+			gpioc: gpio@40020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x800 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOC)>;
+				st,bank-name = "GPIOC";
+			};
+
+			gpiod: gpio@40020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xc00 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOD)>;
+				st,bank-name = "GPIOD";
+			};
+
+			gpioe: gpio@40021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOE)>;
+				st,bank-name = "GPIOE";
+			};
+
+			gpiof: gpio@40021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1400 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOF)>;
+				st,bank-name = "GPIOF";
+			};
+
+			gpiog: gpio@40021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1800 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOG)>;
+				st,bank-name = "GPIOG";
+			};
+
+			gpioh: gpio@40021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOH)>;
+				st,bank-name = "GPIOH";
+			};
+
+			gpioi: gpio@40022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOI)>;
+				st,bank-name = "GPIOI";
+			};
+
+			gpioj: gpio@40022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2400 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOJ)>;
+				st,bank-name = "GPIOJ";
+			};
+
+			gpiok: gpio@40022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2800 0x400>;
+				clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOK)>;
+				st,bank-name = "GPIOK";
+			};
+
+			usart1_pins_a: usart1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 10, AF7)>; /* USART1_RX */
+					bias-disable;
+				};
+			};
+
+			usart3_pins_a: usart3-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
+					bias-disable;
+				};
+			};
+
+			usbotg_fs_pins_a: usbotg-fs-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 10, AF10)>, /* OTG_FS_ID */
+						 <STM32_PINMUX('A', 11, AF10)>, /* OTG_FS_DM */
+						 <STM32_PINMUX('A', 12, AF10)>; /* OTG_FS_DP */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			usbotg_fs_pins_b: usbotg-fs-1 {
+				pins {
+					pinmux = <STM32_PINMUX('B', 12, AF12)>, /* OTG_HS_ID */
+						 <STM32_PINMUX('B', 14, AF12)>, /* OTG_HS_DM */
+						 <STM32_PINMUX('B', 15, AF12)>; /* OTG_HS_DP */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			usbotg_hs_pins_a: usbotg-hs-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT*/
+						 <STM32_PINMUX('I', 11, AF10)>, /* OTG_HS_ULPI_DIR */
+						 <STM32_PINMUX('C', 0, AF10)>, /* OTG_HS_ULPI_STP */
+						 <STM32_PINMUX('A', 5, AF10)>, /* OTG_HS_ULPI_CK */
+						 <STM32_PINMUX('A', 3, AF10)>, /* OTG_HS_ULPI_D0 */
+						 <STM32_PINMUX('B', 0, AF10)>, /* OTG_HS_ULPI_D1 */
+						 <STM32_PINMUX('B', 1, AF10)>, /* OTG_HS_ULPI_D2 */
+						 <STM32_PINMUX('B', 10, AF10)>, /* OTG_HS_ULPI_D3 */
+						 <STM32_PINMUX('B', 11, AF10)>, /* OTG_HS_ULPI_D4 */
+						 <STM32_PINMUX('B', 12, AF10)>, /* OTG_HS_ULPI_D5 */
+						 <STM32_PINMUX('B', 13, AF10)>, /* OTG_HS_ULPI_D6 */
+						 <STM32_PINMUX('B', 5, AF10)>; /* OTG_HS_ULPI_D7 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			ethernet_mii: mii-0 {
+				pins {
+					pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH_MII_TXD0_ETH_RMII_TXD0 */
+						 <STM32_PINMUX('G', 14, AF11)>, /* ETH_MII_TXD1_ETH_RMII_TXD1 */
+						 <STM32_PINMUX('C', 2, AF11)>, /* ETH_MII_TXD2 */
+						 <STM32_PINMUX('B', 8, AF11)>, /* ETH_MII_TXD3 */
+						 <STM32_PINMUX('C', 3, AF11)>, /* ETH_MII_TX_CLK */
+						 <STM32_PINMUX('G', 11,AF11)>, /* ETH_MII_TX_EN_ETH_RMII_TX_EN */
+						 <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
+						 <STM32_PINMUX('C', 1, AF11)>, /* ETH_MDC */
+						 <STM32_PINMUX('A', 1, AF11)>, /* ETH_MII_RX_CLK_ETH_RMII_REF_CLK */
+						 <STM32_PINMUX('A', 7, AF11)>, /* ETH_MII_RX_DV_ETH_RMII_CRS_DV */
+						 <STM32_PINMUX('C', 4, AF11)>, /* ETH_MII_RXD0_ETH_RMII_RXD0 */
+						 <STM32_PINMUX('C', 5, AF11)>, /* ETH_MII_RXD1_ETH_RMII_RXD1 */
+						 <STM32_PINMUX('H', 6, AF11)>, /* ETH_MII_RXD2 */
+						 <STM32_PINMUX('H', 7, AF11)>; /* ETH_MII_RXD3 */
+					slew-rate = <2>;
+				};
+			};
+
+			adc3_in8_pin: adc-200 {
+				pins {
+					pinmux = <STM32_PINMUX('F', 10, ANALOG)>;
+				};
+			};
+
+			pwm1_pins: pwm1-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 8, AF1)>, /* TIM1_CH1 */
+						 <STM32_PINMUX('B', 13, AF1)>, /* TIM1_CH1N */
+						 <STM32_PINMUX('B', 12, AF1)>; /* TIM1_BKIN */
+				};
+			};
+
+			pwm3_pins: pwm3-0 {
+				pins {
+					pinmux = <STM32_PINMUX('B', 4, AF2)>, /* TIM3_CH1 */
+						 <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */
+				};
+			};
+
+			i2c1_pins: i2c1-0 {
+				pins {
+					pinmux = <STM32_PINMUX('B', 9, AF4)>, /* I2C1_SDA */
+						 <STM32_PINMUX('B', 6, AF4)>; /* I2C1_SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <3>;
+				};
+			};
+
+			ltdc_pins_a: ltdc-0 {
+				pins {
+					pinmux = <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */
+						 <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */
+						 <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */
+						 <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */
+						 <STM32_PINMUX('J', 0, AF14)>, /* LCD_R1 */
+						 <STM32_PINMUX('J', 1, AF14)>, /* LCD_R2 */
+						 <STM32_PINMUX('J', 2, AF14)>, /* LCD_R3 */
+						 <STM32_PINMUX('J', 3, AF14)>, /* LCD_R4 */
+						 <STM32_PINMUX('J', 4, AF14)>, /* LCD_R5 */
+						 <STM32_PINMUX('J', 5, AF14)>, /* LCD_R6*/
+						 <STM32_PINMUX('J', 6, AF14)>, /* LCD_R7 */
+						 <STM32_PINMUX('J', 7, AF14)>, /* LCD_G0 */
+						 <STM32_PINMUX('J', 8, AF14)>, /* LCD_G1 */
+						 <STM32_PINMUX('J', 9, AF14)>, /* LCD_G2 */
+						 <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */
+						 <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */
+						 <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */
+						 <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */
+						 <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */
+						 <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3*/
+						 <STM32_PINMUX('K', 0, AF14)>, /* LCD_G5 */
+						 <STM32_PINMUX('K', 1, AF14)>, /* LCD_G6 */
+						 <STM32_PINMUX('K', 2, AF14)>, /* LCD_G7 */
+						 <STM32_PINMUX('K', 3, AF14)>, /* LCD_B4 */
+						 <STM32_PINMUX('K', 4, AF14)>, /* LCD_B5 */
+						 <STM32_PINMUX('K', 5, AF14)>, /* LCD_B6 */
+						 <STM32_PINMUX('K', 6, AF14)>, /* LCD_B7 */
+						 <STM32_PINMUX('K', 7, AF14)>; /* LCD_DE */
+					slew-rate = <2>;
+				};
+			};
+
+			ltdc_pins_b: ltdc-1 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 6,  AF14)>,
+						/* LCD_HSYNC */
+						 <STM32_PINMUX('A', 4,  AF14)>,
+						 /* LCD_VSYNC */
+						 <STM32_PINMUX('G', 7,  AF14)>,
+						 /* LCD_CLK */
+						 <STM32_PINMUX('C', 10, AF14)>,
+						 /* LCD_R2 */
+						 <STM32_PINMUX('B', 0,  AF9)>,
+						 /* LCD_R3 */
+						 <STM32_PINMUX('A', 11, AF14)>,
+						 /* LCD_R4 */
+						 <STM32_PINMUX('A', 12, AF14)>,
+						 /* LCD_R5 */
+						 <STM32_PINMUX('B', 1,  AF9)>,
+						 /* LCD_R6*/
+						 <STM32_PINMUX('G', 6,  AF14)>,
+						 /* LCD_R7 */
+						 <STM32_PINMUX('A', 6,  AF14)>,
+						 /* LCD_G2 */
+						 <STM32_PINMUX('G', 10, AF9)>,
+						 /* LCD_G3 */
+						 <STM32_PINMUX('B', 10, AF14)>,
+						 /* LCD_G4 */
+						 <STM32_PINMUX('D', 6,  AF14)>,
+						 /* LCD_B2 */
+						 <STM32_PINMUX('G', 11, AF14)>,
+						 /* LCD_B3*/
+						 <STM32_PINMUX('B', 11, AF14)>,
+						 /* LCD_G5 */
+						 <STM32_PINMUX('C', 7,  AF14)>,
+						 /* LCD_G6 */
+						 <STM32_PINMUX('D', 3,  AF14)>,
+						 /* LCD_G7 */
+						 <STM32_PINMUX('G', 12, AF9)>,
+						 /* LCD_B4 */
+						 <STM32_PINMUX('A', 3,  AF14)>,
+						 /* LCD_B5 */
+						 <STM32_PINMUX('B', 8,  AF14)>,
+						 /* LCD_B6 */
+						 <STM32_PINMUX('B', 9,  AF14)>,
+						 /* LCD_B7 */
+						 <STM32_PINMUX('F', 10, AF14)>;
+						 /* LCD_DE */
+					slew-rate = <2>;
+				};
+			};
+
+			spi5_pins: spi5-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('F', 7, AF5)>,
+						/* SPI5_CLK */
+						 <STM32_PINMUX('F', 9, AF5)>;
+						/* SPI5_MOSI */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('F', 8, AF5)>;
+						/* SPI5_MISO */
+					bias-disable;
+				};
+			};
+
+			i2c3_pins: i2c3-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 9, AF4)>,
+						/* I2C3_SDA */
+						 <STM32_PINMUX('A', 8, AF4)>;
+						/* I2C3_SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <3>;
+				};
+			};
+
+			dcmi_pins: dcmi-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 4, AF13)>, /* DCMI_HSYNC */
+						 <STM32_PINMUX('B', 7, AF13)>, /* DCMI_VSYNC */
+						 <STM32_PINMUX('A', 6, AF13)>, /* DCMI_PIXCLK */
+						 <STM32_PINMUX('C', 6, AF13)>, /* DCMI_D0 */
+						 <STM32_PINMUX('C', 7, AF13)>, /* DCMI_D1 */
+						 <STM32_PINMUX('C', 8, AF13)>, /* DCMI_D2 */
+						 <STM32_PINMUX('C', 9, AF13)>, /* DCMI_D3 */
+						 <STM32_PINMUX('C', 11, AF13)>, /*DCMI_D4 */
+						 <STM32_PINMUX('D', 3, AF13)>, /* DCMI_D5 */
+						 <STM32_PINMUX('B', 8, AF13)>, /* DCMI_D6 */
+						 <STM32_PINMUX('E', 6, AF13)>, /* DCMI_D7 */
+						 <STM32_PINMUX('C', 10, AF13)>, /* DCMI_D8 */
+						 <STM32_PINMUX('C', 12, AF13)>, /* DCMI_D9 */
+						 <STM32_PINMUX('D', 6, AF13)>, /* DCMI_D10 */
+						 <STM32_PINMUX('D', 2, AF13)>; /* DCMI_D11 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+			};
+
+			sdio_pins: sdio-pins-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDIO_D0 */
+						 <STM32_PINMUX('C', 9, AF12)>, /* SDIO_D1 */
+						 <STM32_PINMUX('C', 10, AF12)>, /* SDIO_D2 */
+						 <STM32_PINMUX('C', 11, AF12)>, /* SDIO_D3 */
+						 <STM32_PINMUX('C', 12, AF12)>, /* SDIO_CK */
+						 <STM32_PINMUX('D', 2, AF12)>; /* SDIO_CMD */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			sdio_pins_od: sdio-pins-od-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDIO_D0 */
+						 <STM32_PINMUX('C', 9, AF12)>, /* SDIO_D1 */
+						 <STM32_PINMUX('C', 10, AF12)>, /* SDIO_D2 */
+						 <STM32_PINMUX('C', 11, AF12)>, /* SDIO_D3 */
+						 <STM32_PINMUX('C', 12, AF12)>; /* SDIO_CK */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDIO_CMD */
+					drive-open-drain;
+					slew-rate = <2>;
+				};
+			};
+
+			can1_pins_a: can1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 9, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 8, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_a: can2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_b: can2-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 12, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32f429-disco.dts b/arch/arm/boot/dts/st/stm32f429-disco.dts
new file mode 100644
index 000000000000..3b81228d46a2
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f429-disco.dts
@@ -0,0 +1,232 @@
+/*
+ * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f429.dtsi"
+#include "stm32f429-pinctrl.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "STMicroelectronics STM32F429i-DISCO board";
+	compatible = "st,stm32f429i-disco", "st,stm32f429";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@90000000 {
+		device_type = "memory";
+		reg = <0x90000000 0x800000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			gpios = <&gpiog 14 0>;
+		};
+		led-green {
+			gpios = <&gpiog 13 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "User";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioa 0 0>;
+		};
+	};
+
+	/* This turns on vbus for otg for host mode (dwc2) */
+	vcc5v_otg: vcc5v-otg-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpioc 4 0>;
+		regulator-name = "vcc5_host1";
+		regulator-always-on;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <8000000>;
+};
+
+&crc {
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	stmpe811@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioa>;
+		/* 3.25 MHz ADC clock speed */
+		st,adc-freq = <1>;
+		/* 12-bit ADC */
+		st,mod-12b = <1>;
+		/* internal ADC reference */
+		st,ref-sel = <0>;
+		/* ADC converstion time: 80 clocks */
+		st,sample-time = <4>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			/* 8 sample average control */
+			st,ave-ctrl = <3>;
+			/* 7 length fractional part in z */
+			st,fraction-z = <7>;
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			/* 1 ms panel driver settling time */
+			st,settling = <3>;
+			/* 5 ms touch detect interrupt delay */
+			st,touch-det-delay = <5>;
+		};
+
+		stmpe_adc {
+			compatible = "st,stmpe-adc";
+			/* forbid to use ADC channels 3-0 (touch) */
+			st,norequest-mask = <0x0F>;
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-names = "default";
+
+	port {
+		ltdc_out_rgb: endpoint {
+			remote-endpoint = <&panel_in_rgb>;
+		};
+	};
+};
+
+&rtc {
+	assigned-clocks = <&rcc 1 CLK_RTC>;
+	assigned-clock-parents = <&rcc 1 CLK_LSI>;
+	status = "okay";
+};
+
+&spi5 {
+	status = "okay";
+	pinctrl-0 = <&spi5_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpioc 1 GPIO_ACTIVE_LOW>, <&gpioc 2 GPIO_ACTIVE_LOW>;
+
+	l3gd20: l3gd20@0 {
+		compatible = "st,l3gd20-gyro";
+		spi-max-frequency = <10000000>;
+		st,drdy-int-pin = <2>;
+		interrupt-parent = <&gpioa>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>,
+				<2 IRQ_TYPE_EDGE_RISING>;
+		reg = <0>;
+		status = "okay";
+	};
+
+	display: display@1{
+		/* Connect panel-ilitek-9341 to ltdc */
+		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
+		reg = <1>;
+		spi-3wire;
+		spi-max-frequency = <10000000>;
+		dc-gpios = <&gpiod 13 0>;
+		port {
+			panel_in_rgb: endpoint {
+			remote-endpoint = <&ltdc_out_rgb>;
+			};
+		};
+	};
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	compatible = "st,stm32f4x9-fsotg";
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_fs_pins_b>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f429-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f429-pinctrl.dtsi
new file mode 100644
index 000000000000..e10d7a1f3207
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f429-pinctrl.dtsi
@@ -0,0 +1,91 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "stm32f4-pinctrl.dtsi"
+
+&pinctrl {
+	compatible = "st,stm32f429-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32f429.dtsi b/arch/arm/boot/dts/st/stm32f429.dtsi
new file mode 100644
index 000000000000..8efcda9ef8ae
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f429.dtsi
@@ -0,0 +1,799 @@
+/*
+ * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "../armv7-m.dtsi"
+#include <dt-bindings/clock/stm32fx-clock.h>
+#include <dt-bindings/mfd/stm32f4-rcc.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+		};
+
+		clk_lse: clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk_lsi: clk-lsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+		};
+
+		clk_i2s_ckin: i2s-ckin {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+		};
+	};
+
+	soc {
+		romem: efuse@1fff7800 {
+			compatible = "st,stm32f4-otp";
+			reg = <0x1fff7800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ts_cal1: calib@22c {
+				reg = <0x22c 0x2>;
+			};
+			ts_cal2: calib@22e {
+				reg = <0x22e 0x2>;
+			};
+		};
+
+		timers2: timers@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM2)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+		};
+
+		timers3: timers@40000400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000400 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM3)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		timers4: timers@40000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000800 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM4)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers5: timers@40000c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000C00 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM5)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+		};
+
+		timers6: timers@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM6)>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timers@40001400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001400 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM7)>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		timers12: timers@40001800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001800 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM12)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timers@40001c00 {
+			compatible = "st,stm32-timers";
+			reg = <0x40001C00 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timers@40002000 {
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		rtc: rtc@40002800 {
+			compatible = "st,stm32-rtc";
+			reg = <0x40002800 0x400>;
+			clocks = <&rcc 1 CLK_RTC>;
+			assigned-clocks = <&rcc 1 CLK_RTC>;
+			assigned-clock-parents = <&rcc 1 CLK_LSE>;
+			interrupt-parent = <&exti>;
+			interrupts = <17 1>;
+			st,syscfg = <&pwrcfg 0x00 0x100>;
+			status = "disabled";
+		};
+
+		iwdg: watchdog@40003000 {
+			compatible = "st,stm32-iwdg";
+			reg = <0x40003000 0x400>;
+			clocks = <&clk_lsi>;
+			clock-names = "lsi";
+			status = "disabled";
+		};
+
+		spi2: spi@40003800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40003800 0x400>;
+			interrupts = <36>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(SPI2)>;
+			status = "disabled";
+		};
+
+		spi3: spi@40003c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40003c00 0x400>;
+			interrupts = <51>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(SPI3)>;
+			status = "disabled";
+		};
+
+		usart2: serial@40004400 {
+			compatible = "st,stm32-uart";
+			reg = <0x40004400 0x400>;
+			interrupts = <38>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART2)>;
+			status = "disabled";
+		};
+
+		usart3: serial@40004800 {
+			compatible = "st,stm32-uart";
+			reg = <0x40004800 0x400>;
+			interrupts = <39>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART3)>;
+			status = "disabled";
+			dmas = <&dma1 1 4 0x400 0x0>,
+			       <&dma1 3 4 0x400 0x0>;
+			dma-names = "rx", "tx";
+		};
+
+		usart4: serial@40004c00 {
+			compatible = "st,stm32-uart";
+			reg = <0x40004c00 0x400>;
+			interrupts = <52>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART4)>;
+			status = "disabled";
+		};
+
+		usart5: serial@40005000 {
+			compatible = "st,stm32-uart";
+			reg = <0x40005000 0x400>;
+			interrupts = <53>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART5)>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@40005400 {
+			compatible = "st,stm32f4-i2c";
+			reg = <0x40005400 0x400>;
+			interrupts = <31>,
+				     <32>;
+			resets = <&rcc STM32F4_APB1_RESET(I2C1)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C1)>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@40005c00 {
+			compatible = "st,stm32f4-i2c";
+			reg = <0x40005c00 0x400>;
+			interrupts = <72>,
+				     <73>;
+			resets = <&rcc STM32F4_APB1_RESET(I2C3)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C3)>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can1: can@40006400 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006400 0x200>;
+			interrupts = <19>, <20>, <21>, <22>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN1)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+			st,can-primary;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
+		gcan: gcan@40006600 {
+			compatible = "st,stm32f4-gcan", "syscon";
+			reg = <0x40006600 0x200>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN1)>;
+		};
+
+		can2: can@40006800 {
+			compatible = "st,stm32f4-bxcan";
+			reg = <0x40006800 0x200>;
+			interrupts = <63>, <64>, <65>, <66>;
+			interrupt-names = "tx", "rx0", "rx1", "sce";
+			resets = <&rcc STM32F4_APB1_RESET(CAN2)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(CAN2)>;
+			st,can-secondary;
+			st,gcan = <&gcan>;
+			status = "disabled";
+		};
+
+		dac: dac@40007400 {
+			compatible = "st,stm32f4-dac-core";
+			reg = <0x40007400 0x400>;
+			resets = <&rcc STM32F4_APB1_RESET(DAC)>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(DAC)>;
+			clock-names = "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dac1: dac@1 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <1>;
+				status = "disabled";
+			};
+
+			dac2: dac@2 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		usart7: serial@40007800 {
+			compatible = "st,stm32-uart";
+			reg = <0x40007800 0x400>;
+			interrupts = <82>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART7)>;
+			status = "disabled";
+		};
+
+		usart8: serial@40007c00 {
+			compatible = "st,stm32-uart";
+			reg = <0x40007c00 0x400>;
+			interrupts = <83>;
+			clocks = <&rcc 0 STM32F4_APB1_CLOCK(UART8)>;
+			status = "disabled";
+		};
+
+		timers1: timers@40010000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40010000 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM1)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+		};
+
+		timers8: timers@40010400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40010400 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM8)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+		};
+
+		usart1: serial@40011000 {
+			compatible = "st,stm32-uart";
+			reg = <0x40011000 0x400>;
+			interrupts = <37>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(USART1)>;
+			status = "disabled";
+			dmas = <&dma2 2 4 0x400 0x0>,
+			       <&dma2 7 4 0x400 0x0>;
+			dma-names = "rx", "tx";
+		};
+
+		usart6: serial@40011400 {
+			compatible = "st,stm32-uart";
+			reg = <0x40011400 0x400>;
+			interrupts = <71>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(USART6)>;
+			status = "disabled";
+		};
+
+		adc: adc@40012000 {
+			compatible = "st,stm32f4-adc-core";
+			reg = <0x40012000 0x400>;
+			interrupts = <18>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC1)>;
+			clock-names = "adc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc1: adc@0 {
+				compatible = "st,stm32f4-adc";
+				#io-channel-cells = <1>;
+				reg = <0x0>;
+				clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC1)>;
+				interrupt-parent = <&adc>;
+				interrupts = <0>;
+				dmas = <&dma2 0 0 0x400 0x0>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			adc2: adc@100 {
+				compatible = "st,stm32f4-adc";
+				#io-channel-cells = <1>;
+				reg = <0x100>;
+				clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC2)>;
+				interrupt-parent = <&adc>;
+				interrupts = <1>;
+				dmas = <&dma2 3 1 0x400 0x0>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			adc3: adc@200 {
+				compatible = "st,stm32f4-adc";
+				#io-channel-cells = <1>;
+				reg = <0x200>;
+				clocks = <&rcc 0 STM32F4_APB2_CLOCK(ADC3)>;
+				interrupt-parent = <&adc>;
+				interrupts = <2>;
+				dmas = <&dma2 1 2 0x400 0x0>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+		};
+
+		sdio: mmc@40012c00 {
+			compatible = "arm,pl180", "arm,primecell";
+			arm,primecell-periphid = <0x00880180>;
+			reg = <0x40012c00 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SDIO)>;
+			clock-names = "apb_pclk";
+			interrupts = <49>;
+			max-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		spi1: spi@40013000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40013000 0x400>;
+			interrupts = <35>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SPI1)>;
+			status = "disabled";
+		};
+
+		spi4: spi@40013400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40013400 0x400>;
+			interrupts = <84>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SPI4)>;
+			status = "disabled";
+		};
+
+		syscfg: syscon@40013800 {
+			compatible = "st,stm32-syscfg", "syscon";
+			reg = <0x40013800 0x400>;
+		};
+
+		exti: interrupt-controller@40013c00 {
+			compatible = "st,stm32-exti";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x40013C00 0x400>;
+			interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>;
+		};
+
+		timers9: timers@40014000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40014000 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM9)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@8 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <8>;
+				status = "disabled";
+			};
+		};
+
+		timers10: timers@40014400 {
+			compatible = "st,stm32-timers";
+			reg = <0x40014400 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers11: timers@40014800 {
+			compatible = "st,stm32-timers";
+			reg = <0x40014800 0x400>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		spi5: spi@40015000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40015000 0x400>;
+			interrupts = <85>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SPI5)>;
+			dmas = <&dma2 3 2 0x400 0x0>,
+				<&dma2 4 2 0x400 0x0>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi6: spi@40015400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32f4-spi";
+			reg = <0x40015400 0x400>;
+			interrupts = <86>;
+			clocks = <&rcc 0 STM32F4_APB2_CLOCK(SPI6)>;
+			status = "disabled";
+		};
+
+		pwrcfg: power-config@40007000 {
+			compatible = "st,stm32-power-config", "syscon";
+			reg = <0x40007000 0x400>;
+		};
+
+		ltdc: display-controller@40016800 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x40016800 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32F4_APB2_RESET(LTDC)>;
+			clocks = <&rcc 1 CLK_LCD>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		crc: crc@40023000 {
+			compatible = "st,stm32f4-crc";
+			reg = <0x40023000 0x400>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(CRC)>;
+			status = "disabled";
+		};
+
+		rcc: rcc@40023800 {
+			#reset-cells = <1>;
+			#clock-cells = <2>;
+			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
+			reg = <0x40023800 0x400>;
+			clocks = <&clk_hse>, <&clk_i2s_ckin>;
+			st,syscfg = <&pwrcfg>;
+			assigned-clocks = <&rcc 1 CLK_HSE_RTC>;
+			assigned-clock-rates = <1000000>;
+		};
+
+		dma1: dma-controller@40026000 {
+			compatible = "st,stm32-dma";
+			reg = <0x40026000 0x400>;
+			interrupts = <11>,
+				     <12>,
+				     <13>,
+				     <14>,
+				     <15>,
+				     <16>,
+				     <17>,
+				     <47>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA1)>;
+			#dma-cells = <4>;
+		};
+
+		dma2: dma-controller@40026400 {
+			compatible = "st,stm32-dma";
+			reg = <0x40026400 0x400>;
+			interrupts = <56>,
+				     <57>,
+				     <58>,
+				     <59>,
+				     <60>,
+				     <68>,
+				     <69>,
+				     <70>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2)>;
+			#dma-cells = <4>;
+			st,mem2mem;
+		};
+
+		mac: ethernet@40028000 {
+			compatible = "st,stm32-dwmac", "snps,dwmac-3.50a";
+			reg = <0x40028000 0x8000>;
+			reg-names = "stmmaceth";
+			interrupts = <61>;
+			interrupt-names = "macirq";
+			clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(ETHMAC)>,
+					<&rcc 0 STM32F4_AHB1_CLOCK(ETHMACTX)>,
+					<&rcc 0 STM32F4_AHB1_CLOCK(ETHMACRX)>;
+			st,syscon = <&syscfg 0x4>;
+			snps,pbl = <8>;
+			snps,mixed-burst;
+			status = "disabled";
+		};
+
+		dma2d: dma2d@4002b000 {
+			compatible = "st,stm32-dma2d";
+			reg = <0x4002b000 0xc00>;
+			interrupts = <90>;
+			resets = <&rcc STM32F4_AHB1_RESET(DMA2D)>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2D)>;
+			clock-names = "dma2d";
+			status = "disabled";
+		};
+
+		usbotg_hs: usb@40040000 {
+			compatible = "snps,dwc2";
+			reg = <0x40040000 0x40000>;
+			interrupts = <77>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(OTGHS)>;
+			clock-names = "otg";
+			status = "disabled";
+		};
+
+		usbotg_fs: usb@50000000 {
+			compatible = "st,stm32f4x9-fsotg";
+			reg = <0x50000000 0x40000>;
+			interrupts = <67>;
+			clocks = <&rcc 0 39>;
+			clock-names = "otg";
+			status = "disabled";
+		};
+
+		dcmi: dcmi@50050000 {
+			compatible = "st,stm32-dcmi";
+			reg = <0x50050000 0x400>;
+			interrupts = <78>;
+			resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
+			clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
+			clock-names = "mclk";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dcmi_pins>;
+			dmas = <&dma2 1 1 0x414 0x3>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
+		rng: rng@50060800 {
+			compatible = "st,stm32-rng";
+			reg = <0x50060800 0x400>;
+			clocks = <&rcc 0 STM32F4_AHB2_CLOCK(RNG)>;
+
+		};
+	};
+};
+
+&systick {
+	clocks = <&rcc 1 SYSTICK>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f469-disco.dts b/arch/arm/boot/dts/st/stm32f469-disco.dts
new file mode 100644
index 000000000000..cbbd521bf010
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f469-disco.dts
@@ -0,0 +1,254 @@
+/*
+ * Copyright 2016 - Lee Jones <lee.jones@linaro.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f469.dtsi"
+#include "stm32f469-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "STMicroelectronics STM32F469i-DISCO board";
+	compatible = "st,stm32f469i-disco", "st,stm32f469";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x1000000>;
+	};
+
+	aliases {
+		serial0 = &usart3;
+	};
+
+	mmc_vcard: mmc_vcard {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcard";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vdd_dsi: vdd-dsi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_dsi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	soc {
+		dma-ranges = <0xc0000000 0x0 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-green {
+			gpios = <&gpiog 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-orange {
+			gpios = <&gpiod 4 GPIO_ACTIVE_LOW>;
+		};
+		led-red {
+			gpios = <&gpiod 5 GPIO_ACTIVE_LOW>;
+		};
+		led-blue {
+			gpios = <&gpiok 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "User";
+			linux,code = <KEY_WAKEUP>;
+			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	/* This turns on vbus for otg for host mode (dwc2) */
+	vcc5v_otg: vcc5v-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpiob 2 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5_host1";
+		regulator-always-on;
+	};
+};
+
+&rcc {
+	compatible = "st,stm32f469-rcc", "st,stm32f42xx-rcc", "st,stm32-rcc";
+};
+
+&clk_hse {
+	clock-frequency = <8000000>;
+};
+
+&dma2d {
+	status = "okay";
+};
+
+&dsi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_out_dsi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&dsi_panel_in>;
+			};
+		};
+	};
+
+	panel@0 {
+		compatible = "orisetech,otm8009a";
+		reg = <0>; /* dsi virtual channel (0..3) */
+		reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_dsi>;
+		status = "okay";
+
+		port {
+			dsi_panel_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&timers1 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm1_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm3_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&sdio {
+	status = "okay";
+	vmmc-supply = <&mmc_vcard>;
+	cd-gpios = <&gpiog 2 GPIO_ACTIVE_LOW>;
+	broken-cd;
+	pinctrl-names = "default", "opendrain";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_pins_od>;
+	bus-width = <4>;
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart3 {
+	pinctrl-0 = <&usart3_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_fs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_fs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f469-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f469-pinctrl.dtsi
new file mode 100644
index 000000000000..6bf60263dff8
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f469-pinctrl.dtsi
@@ -0,0 +1,92 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "stm32f4-pinctrl.dtsi"
+
+&pinctrl {
+	compatible = "st,stm32f469-pinctrl";
+
+	gpioa: gpio@40020000 {
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@40020400 {
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@40020800 {
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@40020c00 {
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@40021000 {
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@40021400 {
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@40021800 {
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@40021c00 {
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@40022000 {
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@40022400 {
+		gpio-ranges = <&pinctrl 0 144 6>,
+			      <&pinctrl 12 156 4>;
+	};
+
+	gpiok: gpio@40022800 {
+		gpio-ranges = <&pinctrl 3 163 5>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32f469.dtsi b/arch/arm/boot/dts/st/stm32f469.dtsi
new file mode 100644
index 000000000000..be002e8a78ac
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f469.dtsi
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2017 - All Rights Reserved */
+
+#include "stm32f429.dtsi"
+
+/ {
+	soc {
+		dsi: dsi@40016c00 {
+			compatible = "st,stm32-dsi";
+			reg = <0x40016c00 0x800>;
+			resets = <&rcc STM32F4_APB2_RESET(DSI)>;
+			reset-names = "apb";
+			clocks = <&rcc 1 CLK_F469_DSI>, <&clk_hse>;
+			clock-names = "pclk", "ref";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi
new file mode 100644
index 000000000000..9f65403295ca
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f7-pinctrl.dtsi
@@ -0,0 +1,370 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+#include <dt-bindings/mfd/stm32f7-rcc.h>
+
+/ {
+	soc {
+		pinctrl: pinctrl@40020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x40020000 0x3000>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&syscfg 0x8>;
+
+			gpioa: gpio@40020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOA)>;
+				st,bank-name = "GPIOA";
+			};
+
+			gpiob: gpio@40020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x400 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOB)>;
+				st,bank-name = "GPIOB";
+			};
+
+			gpioc: gpio@40020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x800 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOC)>;
+				st,bank-name = "GPIOC";
+			};
+
+			gpiod: gpio@40020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xc00 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOD)>;
+				st,bank-name = "GPIOD";
+			};
+
+			gpioe: gpio@40021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOE)>;
+				st,bank-name = "GPIOE";
+			};
+
+			gpiof: gpio@40021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1400 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOF)>;
+				st,bank-name = "GPIOF";
+			};
+
+			gpiog: gpio@40021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1800 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOG)>;
+				st,bank-name = "GPIOG";
+			};
+
+			gpioh: gpio@40021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOH)>;
+				st,bank-name = "GPIOH";
+			};
+
+			gpioi: gpio@40022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOI)>;
+				st,bank-name = "GPIOI";
+			};
+
+			gpioj: gpio@40022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2400 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOJ)>;
+				st,bank-name = "GPIOJ";
+			};
+
+			gpiok: gpio@40022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2800 0x400>;
+				clocks = <&rcc 0 STM32F7_AHB1_CLOCK(GPIOK)>;
+				st,bank-name = "GPIOK";
+			};
+
+			cec_pins_a: cec-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 15, AF4)>; /* HDMI CEC */
+					slew-rate = <0>;
+					drive-open-drain;
+					bias-disable;
+				};
+			};
+
+			usart1_pins_a: usart1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 10, AF7)>; /* USART1_RX */
+					bias-disable;
+				};
+			};
+
+			usart1_pins_b: usart1-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 9, AF7)>; /* USART1_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 7, AF7)>; /* USART1_RX */
+					bias-disable;
+				};
+			};
+
+			i2c1_pins_b: i2c1-0 {
+				pins {
+					pinmux = <STM32_PINMUX('B', 9, AF4)>, /* I2C1 SDA */
+						 <STM32_PINMUX('B', 8, AF4)>; /* I2C1 SCL */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			usbotg_hs_pins_a: usbotg-hs-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT */
+						 <STM32_PINMUX('I', 11, AF10)>, /* OTG_HS_ULPI_DIR */
+						 <STM32_PINMUX('C', 0, AF10)>, /* OTG_HS_ULPI_STP */
+						 <STM32_PINMUX('A', 5, AF10)>, /* OTG_HS_ULPI_CK */
+						 <STM32_PINMUX('A', 3, AF10)>, /* OTG_HS_ULPI_D0 */
+						 <STM32_PINMUX('B', 0, AF10)>, /* OTG_HS_ULPI_D1 */
+						 <STM32_PINMUX('B', 1, AF10)>, /* OTG_HS_ULPI_D2 */
+						 <STM32_PINMUX('B', 10, AF10)>, /* OTG_HS_ULPI_D3 */
+						 <STM32_PINMUX('B', 11, AF10)>, /* OTG_HS_ULPI_D4 */
+						 <STM32_PINMUX('B', 12, AF10)>, /* OTG_HS_ULPI_D5 */
+						 <STM32_PINMUX('B', 13, AF10)>, /* OTG_HS_ULPI_D6 */
+						 <STM32_PINMUX('B', 5, AF10)>; /* OTG_HS_ULPI_D7 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			usbotg_hs_pins_b: usbotg-hs-1 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 4, AF10)>, /* OTG_HS_ULPI_NXT */
+						 <STM32_PINMUX('C', 2, AF10)>, /* OTG_HS_ULPI_DIR */
+						 <STM32_PINMUX('C', 0, AF10)>, /* OTG_HS_ULPI_STP */
+						 <STM32_PINMUX('A', 5, AF10)>, /* OTG_HS_ULPI_CK */
+						 <STM32_PINMUX('A', 3, AF10)>, /* OTG_HS_ULPI_D0 */
+						 <STM32_PINMUX('B', 0, AF10)>, /* OTG_HS_ULPI_D1 */
+						 <STM32_PINMUX('B', 1, AF10)>, /* OTG_HS_ULPI_D2 */
+						 <STM32_PINMUX('B', 10, AF10)>, /* OTG_HS_ULPI_D3 */
+						 <STM32_PINMUX('B', 11, AF10)>, /* OTG_HS_ULPI_D4 */
+						 <STM32_PINMUX('B', 12, AF10)>, /* OTG_HS_ULPI_D5 */
+						 <STM32_PINMUX('B', 13, AF10)>, /* OTG_HS_ULPI_D6 */
+						 <STM32_PINMUX('B', 5, AF10)>; /* OTG_HS_ULPI_D7 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			usbotg_fs_pins_a: usbotg-fs-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 10, AF10)>, /* OTG_FS_ID */
+						 <STM32_PINMUX('A', 11, AF10)>, /* OTG_FS_DM */
+						 <STM32_PINMUX('A', 12, AF10)>; /* OTG_FS_DP */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			sdio_pins_a: sdio-pins-a-0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1 D0 */
+						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1 D1 */
+						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1 D2 */
+						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1 D3 */
+						 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1 CLK */
+						 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1 CMD */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			sdio_pins_od_a: sdio-pins-od-a-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1 D0 */
+						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1 D1 */
+						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1 D2 */
+						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1 D3 */
+						 <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1 CLK */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1 CMD */
+					drive-open-drain;
+					slew-rate = <2>;
+				};
+			};
+
+			sdio_pins_b: sdio-pins-b-0 {
+				pins {
+					pinmux = <STM32_PINMUX('G', 9, AF11)>, /* SDMMC2 D0 */
+						 <STM32_PINMUX('G', 10, AF11)>, /* SDMMC2 D1 */
+						 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2 D2 */
+						 <STM32_PINMUX('B', 4, AF10)>, /* SDMMC2 D3 */
+						 <STM32_PINMUX('D', 6, AF11)>, /* SDMMC2 CLK */
+						 <STM32_PINMUX('D', 7, AF11)>; /* SDMMC2 CMD */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+			};
+
+			sdio_pins_od_b: sdio-pins-od-b-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('G', 9, AF11)>, /* SDMMC2 D0 */
+						 <STM32_PINMUX('G', 10, AF11)>, /* SDMMC2 D1 */
+						 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2 D2 */
+						 <STM32_PINMUX('B', 4, AF10)>, /* SDMMC2 D3 */
+						 <STM32_PINMUX('D', 6, AF11)>; /* SDMMC2 CLK */
+					drive-push-pull;
+					slew-rate = <2>;
+				};
+
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC2 CMD */
+					drive-open-drain;
+					slew-rate = <2>;
+				};
+			};
+
+			can1_pins_a: can1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 12, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 11, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_b: can1-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 9, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 8, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+				};
+			};
+
+			can1_pins_c: can1-2 {
+				pins1 {
+					pinmux = <STM32_PINMUX('D', 1, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('D', 0, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can1_pins_d: can1-3 {
+				pins1 {
+					pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+					bias-pull-up;
+
+				};
+			};
+
+			can2_pins_a: can2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 6, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can2_pins_b: can2-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 12, AF9)>; /* CAN2_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_a: can3-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('A', 15, AF11)>; /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('A', 8, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
+
+			can3_pins_b: can3-1 {
+				pins1 {
+					pinmux = <STM32_PINMUX('B', 4, AF11)>;  /* CAN3_TX */
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 3, AF11)>; /* CAN3_RX */
+					bias-pull-up;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32f746-disco.dts b/arch/arm/boot/dts/st/stm32f746-disco.dts
new file mode 100644
index 000000000000..c11616ed5fc6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f746-disco.dts
@@ -0,0 +1,144 @@
+/*
+ * Copyright 2017 - Vikas MANOCHA <vikas.manocha@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f746.dtsi"
+#include "stm32f746-pinctrl.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "STMicroelectronics STM32F746-DISCO board";
+	compatible = "st,stm32f746-disco", "st,stm32f746";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x800000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	usbotg_hs_phy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHSULPI)>;
+		clock-names = "main_clk";
+	};
+
+	/* This turns on vbus for otg fs for host mode (dwc2) */
+	vcc5v_otg_fs: vcc5v-otg-fs-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpiod 5 0>;
+		regulator-name = "vcc5_host1";
+		regulator-always-on;
+	};
+
+	mmc_vcard: mmc_vcard {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcard";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-names = "default";
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&sdio1 {
+	status = "okay";
+	vmmc-supply = <&mmc_vcard>;
+	cd-gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default", "opendrain";
+	pinctrl-0 = <&sdio_pins_a>;
+	pinctrl-1 = <&sdio_pins_od_a>;
+	bus-width = <4>;
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_b>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_fs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_fs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	pinctrl-0 = <&usbotg_hs_pins_b>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi
new file mode 100644
index 000000000000..fcfd2ac7239b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f746-pinctrl.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32f7-pinctrl.dtsi"
+
+&pinctrl{
+	compatible = "st,stm32f746-pinctrl";
+};
diff --git a/arch/arm/boot/dts/st/stm32f746.dtsi b/arch/arm/boot/dts/st/stm32f746.dtsi
new file mode 100644
index 000000000000..d1802efd067c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f746.dtsi
@@ -0,0 +1,592 @@
+/*
+ * Copyright 2015 - Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "../armv7-m.dtsi"
+#include <dt-bindings/clock/stm32fx-clock.h>
+#include <dt-bindings/mfd/stm32f7-rcc.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+		};
+
+		clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk-lsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+		};
+
+		clk_i2s_ckin: clk-i2s-ckin {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+		};
+	};
+
+	soc {
+		timers2: timers@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM2)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+		};
+
+		timers3: timers@40000400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000400 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM3)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		timers4: timers@40000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000800 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM4)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers5: timers@40000c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000C00 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+		};
+
+		timers6: timers@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM6)>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timers@40001400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001400 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM7)>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		timers12: timers@40001800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001800 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM12)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timers@40001c00 {
+			compatible = "st,stm32-timers";
+			reg = <0x40001C00 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timers@40002000 {
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		rtc: rtc@40002800 {
+			compatible = "st,stm32-rtc";
+			reg = <0x40002800 0x400>;
+			clocks = <&rcc 1 CLK_RTC>;
+			assigned-clocks = <&rcc 1 CLK_RTC>;
+			assigned-clock-parents = <&rcc 1 CLK_LSE>;
+			interrupt-parent = <&exti>;
+			interrupts = <17 1>;
+			st,syscfg = <&pwrcfg 0x00 0x100>;
+			status = "disabled";
+		};
+
+		usart2: serial@40004400 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40004400 0x400>;
+			interrupts = <38>;
+			clocks = <&rcc 1 CLK_USART2>;
+			status = "disabled";
+		};
+
+		usart3: serial@40004800 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40004800 0x400>;
+			interrupts = <39>;
+			clocks = <&rcc 1 CLK_USART3>;
+			status = "disabled";
+		};
+
+		usart4: serial@40004c00 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40004c00 0x400>;
+			interrupts = <52>;
+			clocks = <&rcc 1 CLK_UART4>;
+			status = "disabled";
+		};
+
+		usart5: serial@40005000 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40005000 0x400>;
+			interrupts = <53>;
+			clocks = <&rcc 1 CLK_UART5>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@40005400 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40005400 0x400>;
+			interrupts = <31>,
+				     <32>;
+			resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+			clocks = <&rcc 1 CLK_I2C1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40005800 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40005800 0x400>;
+			interrupts = <33>,
+				     <34>;
+			resets = <&rcc STM32F7_APB1_RESET(I2C2)>;
+			clocks = <&rcc 1 CLK_I2C2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@40005c00 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40005c00 0x400>;
+			interrupts = <72>,
+				     <73>;
+			resets = <&rcc STM32F7_APB1_RESET(I2C3)>;
+			clocks = <&rcc 1 CLK_I2C3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@40006000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40006000 0x400>;
+			interrupts = <95>,
+				     <96>;
+			resets = <&rcc STM32F7_APB1_RESET(I2C4)>;
+			clocks = <&rcc 1 CLK_I2C4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		cec: cec@40006c00 {
+			compatible = "st,stm32-cec";
+			reg = <0x40006C00 0x400>;
+			interrupts = <94>;
+			clocks = <&rcc 0 STM32F7_APB1_CLOCK(CEC)>, <&rcc 1 CLK_HDMI_CEC>;
+			clock-names = "cec", "hdmi-cec";
+			status = "disabled";
+		};
+
+		usart7: serial@40007800 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40007800 0x400>;
+			interrupts = <82>;
+			clocks = <&rcc 1 CLK_UART7>;
+			status = "disabled";
+		};
+
+		usart8: serial@40007c00 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40007c00 0x400>;
+			interrupts = <83>;
+			clocks = <&rcc 1 CLK_UART8>;
+			status = "disabled";
+		};
+
+		timers1: timers@40010000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40010000 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM1)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+		};
+
+		timers8: timers@40010400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40010400 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM8)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+		};
+
+		usart1: serial@40011000 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts = <37>;
+			clocks = <&rcc 1 CLK_USART1>;
+			status = "disabled";
+		};
+
+		usart6: serial@40011400 {
+			compatible = "st,stm32f7-uart";
+			reg = <0x40011400 0x400>;
+			interrupts = <71>;
+			clocks = <&rcc 1 CLK_USART6>;
+			status = "disabled";
+		};
+
+		sdio2: mmc@40011c00 {
+			compatible = "arm,pl180", "arm,primecell";
+			arm,primecell-periphid = <0x00880180>;
+			reg = <0x40011c00 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SDMMC2)>;
+			clock-names = "apb_pclk";
+			interrupts = <103>;
+			max-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		sdio1: mmc@40012c00 {
+			compatible = "arm,pl180", "arm,primecell";
+			arm,primecell-periphid = <0x00880180>;
+			reg = <0x40012c00 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(SDMMC1)>;
+			clock-names = "apb_pclk";
+			interrupts = <49>;
+			max-frequency = <48000000>;
+			status = "disabled";
+		};
+
+		syscfg: syscon@40013800 {
+			compatible = "st,stm32-syscfg", "syscon";
+			reg = <0x40013800 0x400>;
+		};
+
+		exti: interrupt-controller@40013c00 {
+			compatible = "st,stm32-exti";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x40013C00 0x400>;
+			interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <42>, <62>, <76>;
+		};
+
+		timers9: timers@40014000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40014000 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM9)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@8 {
+				compatible = "st,stm32-timer-trigger";
+				reg = <8>;
+				status = "disabled";
+			};
+		};
+
+		timers10: timers@40014400 {
+			compatible = "st,stm32-timers";
+			reg = <0x40014400 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers11: timers@40014800 {
+			compatible = "st,stm32-timers";
+			reg = <0x40014800 0x400>;
+			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		pwrcfg: power-config@40007000 {
+			compatible = "st,stm32-power-config", "syscon";
+			reg = <0x40007000 0x400>;
+		};
+
+		crc: crc@40023000 {
+			compatible = "st,stm32f7-crc";
+			reg = <0x40023000 0x400>;
+			clocks = <&rcc 0 STM32F7_AHB1_CLOCK(CRC)>;
+			status = "disabled";
+		};
+
+		rcc: rcc@40023800 {
+			#reset-cells = <1>;
+			#clock-cells = <2>;
+			compatible = "st,stm32f746-rcc", "st,stm32-rcc";
+			reg = <0x40023800 0x400>;
+			clocks = <&clk_hse>, <&clk_i2s_ckin>;
+			st,syscfg = <&pwrcfg>;
+			assigned-clocks = <&rcc 1 CLK_HSE_RTC>;
+			assigned-clock-rates = <1000000>;
+		};
+
+		dma1: dma-controller@40026000 {
+			compatible = "st,stm32-dma";
+			reg = <0x40026000 0x400>;
+			interrupts = <11>,
+				     <12>,
+				     <13>,
+				     <14>,
+				     <15>,
+				     <16>,
+				     <17>,
+				     <47>;
+			clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA1)>;
+			#dma-cells = <4>;
+			status = "disabled";
+		};
+
+		dma2: dma-controller@40026400 {
+			compatible = "st,stm32-dma";
+			reg = <0x40026400 0x400>;
+			interrupts = <56>,
+				     <57>,
+				     <58>,
+				     <59>,
+				     <60>,
+				     <68>,
+				     <69>,
+				     <70>;
+			clocks = <&rcc 0 STM32F7_AHB1_CLOCK(DMA2)>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			status = "disabled";
+		};
+
+		usbotg_hs: usb@40040000 {
+			compatible = "st,stm32f7-hsotg";
+			reg = <0x40040000 0x40000>;
+			interrupts = <77>;
+			clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHS)>;
+			clock-names = "otg";
+			g-rx-fifo-size = <256>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
+			status = "disabled";
+		};
+
+		usbotg_fs: usb@50000000 {
+			compatible = "st,stm32f4x9-fsotg";
+			reg = <0x50000000 0x40000>;
+			interrupts = <67>;
+			clocks = <&rcc 0 STM32F7_AHB2_CLOCK(OTGFS)>;
+			clock-names = "otg";
+			status = "disabled";
+		};
+	};
+};
+
+&systick {
+	clocks = <&rcc 1 0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f769-disco.dts b/arch/arm/boot/dts/st/stm32f769-disco.dts
new file mode 100644
index 000000000000..b038d0ed39e8
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f769-disco.dts
@@ -0,0 +1,165 @@
+/*
+ * Copyright 2017 - Vikas MANOCHA <vikas.manocha@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32f746.dtsi"
+#include "stm32f769-pinctrl.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "STMicroelectronics STM32F769-DISCO board";
+	compatible = "st,stm32f769-disco", "st,stm32f769";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x1000000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-green {
+			gpios = <&gpioj 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+		led-red {
+			gpios = <&gpioj 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		button-0 {
+			label = "User";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	usbotg_hs_phy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc 0 STM32F7_AHB1_CLOCK(OTGHSULPI)>;
+		clock-names = "main_clk";
+	};
+
+	mmc_vcard: mmc_vcard {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcard";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&rcc {
+	compatible = "st,stm32f769-rcc", "st,stm32f746-rcc", "st,stm32-rcc";
+};
+
+&cec {
+	pinctrl-0 = <&cec_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-names = "default";
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdio2 {
+	status = "okay";
+	vmmc-supply = <&mmc_vcard>;
+	cd-gpios = <&gpioi 15 GPIO_ACTIVE_LOW>;
+	broken-cd;
+	pinctrl-names = "default", "opendrain";
+	pinctrl-0 = <&sdio_pins_b>;
+	pinctrl-1 = <&sdio_pins_od_b>;
+	bus-width = <4>;
+};
+
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi
new file mode 100644
index 000000000000..31005dd9929c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32f769-pinctrl.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Alexandre Torgue  <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32f7-pinctrl.dtsi"
+
+&pinctrl{
+	compatible = "st,stm32f769-pinctrl";
+};
diff --git a/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi
new file mode 100644
index 000000000000..aa1bc3e10a49
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h7-pinctrl.dtsi
@@ -0,0 +1,275 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */
+				 <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	ethernet_rmii: rmii-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 11, AF11)>,
+				 <STM32_PINMUX('G', 13, AF11)>,
+				 <STM32_PINMUX('G', 12, AF11)>,
+				 <STM32_PINMUX('C', 4, AF11)>,
+				 <STM32_PINMUX('C', 5, AF11)>,
+				 <STM32_PINMUX('A', 7, AF11)>,
+				 <STM32_PINMUX('C', 1, AF11)>,
+				 <STM32_PINMUX('A', 2, AF11)>,
+				 <STM32_PINMUX('A', 1, AF11)>;
+			slew-rate = <2>;
+		};
+	};
+
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2{
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2{
+			pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */
+			slew-rate = <3>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2{
+			pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */
+			slew-rate = <3>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	spi1_pins: spi1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 5, AF5)>,
+				/* SPI1_CLK */
+				 <STM32_PINMUX('B', 5, AF5)>;
+				/* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 9, AF5)>;
+				/* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	uart4_pins: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	usart1_pins: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_pins: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_pins: usart3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usbotg_hs_pins_a: usbotg-hs-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, AF10)>,	/* ULPI_NXT */
+					 <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */
+					 <STM32_PINMUX('C', 0, AF10)>,	/* ULPI_STP> */
+					 <STM32_PINMUX('A', 5, AF10)>,	/* ULPI_CK> */
+					 <STM32_PINMUX('A', 3, AF10)>,	/* ULPI_D0> */
+					 <STM32_PINMUX('B', 0, AF10)>,	/* ULPI_D1> */
+					 <STM32_PINMUX('B', 1, AF10)>,	/* ULPI_D2> */
+					 <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */
+					 <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */
+					 <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */
+					 <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */
+					 <STM32_PINMUX('B', 5, AF10)>;	/* ULPI_D7> */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+};
+
diff --git a/arch/arm/boot/dts/st/stm32h743.dtsi b/arch/arm/boot/dts/st/stm32h743.dtsi
new file mode 100644
index 000000000000..b8d4c44c8a82
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h743.dtsi
@@ -0,0 +1,730 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "../armv7-m.dtsi"
+#include <dt-bindings/clock/stm32h7-clks.h>
+#include <dt-bindings/mfd/stm32h7-rcc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+		};
+
+		clk_lse: clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk_i2s: i2s_ckin {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <0>;
+		};
+	};
+
+	soc {
+		timer5: timer@40000c00 {
+			compatible = "st,stm32-timer";
+			reg = <0x40000c00 0x400>;
+			interrupts = <50>;
+			clocks = <&rcc TIM5_CK>;
+		};
+
+		lptimer1: timer@40002400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x40002400 0x400>;
+			clocks = <&rcc LPTIM1_CK>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@0 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		spi2: spi@40003800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x40003800 0x400>;
+			interrupts = <36>;
+			resets = <&rcc STM32H7_APB1L_RESET(SPI2)>;
+			clocks = <&rcc SPI2_CK>;
+			status = "disabled";
+
+		};
+
+		spi3: spi@40003c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x40003c00 0x400>;
+			interrupts = <51>;
+			resets = <&rcc STM32H7_APB1L_RESET(SPI3)>;
+			clocks = <&rcc SPI3_CK>;
+			status = "disabled";
+		};
+
+		usart2: serial@40004400 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004400 0x400>;
+			interrupts = <38>;
+			status = "disabled";
+			clocks = <&rcc USART2_CK>;
+		};
+
+		usart3: serial@40004800 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004800 0x400>;
+			interrupts = <39>;
+			status = "disabled";
+			clocks = <&rcc USART3_CK>;
+		};
+
+		uart4: serial@40004c00 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40004c00 0x400>;
+			interrupts = <52>;
+			status = "disabled";
+			clocks = <&rcc UART4_CK>;
+		};
+
+		i2c1: i2c@40005400 {
+			compatible = "st,stm32f7-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x40005400 0x400>;
+			interrupts = <31>,
+				     <32>;
+			resets = <&rcc STM32H7_APB1L_RESET(I2C1)>;
+			clocks = <&rcc I2C1_CK>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40005800 {
+			compatible = "st,stm32f7-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x40005800 0x400>;
+			interrupts = <33>,
+				     <34>;
+			resets = <&rcc STM32H7_APB1L_RESET(I2C2)>;
+			clocks = <&rcc I2C2_CK>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@40005c00 {
+			compatible = "st,stm32f7-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x40005C00 0x400>;
+			interrupts = <72>,
+				     <73>;
+			resets = <&rcc STM32H7_APB1L_RESET(I2C3)>;
+			clocks = <&rcc I2C3_CK>;
+			status = "disabled";
+		};
+
+		dac: dac@40007400 {
+			compatible = "st,stm32h7-dac-core";
+			reg = <0x40007400 0x400>;
+			clocks = <&rcc DAC12_CK>;
+			clock-names = "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dac1: dac@1 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <1>;
+				status = "disabled";
+			};
+
+			dac2: dac@2 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		usart1: serial@40011000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts = <37>;
+			status = "disabled";
+			clocks = <&rcc USART1_CK>;
+		};
+
+		spi1: spi@40013000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x40013000 0x400>;
+			interrupts = <35>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI1)>;
+			clocks = <&rcc SPI1_CK>;
+			status = "disabled";
+		};
+
+		spi4: spi@40013400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x40013400 0x400>;
+			interrupts = <84>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI4)>;
+			clocks = <&rcc SPI4_CK>;
+			status = "disabled";
+		};
+
+		spi5: spi@40015000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x40015000 0x400>;
+			interrupts = <85>;
+			resets = <&rcc STM32H7_APB2_RESET(SPI5)>;
+			clocks = <&rcc SPI5_CK>;
+			status = "disabled";
+		};
+
+		dma1: dma-controller@40020000 {
+			compatible = "st,stm32-dma";
+			reg = <0x40020000 0x400>;
+			interrupts = <11>,
+				     <12>,
+				     <13>,
+				     <14>,
+				     <15>,
+				     <16>,
+				     <17>,
+				     <47>;
+			clocks = <&rcc DMA1_CK>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+			status = "disabled";
+		};
+
+		dma2: dma-controller@40020400 {
+			compatible = "st,stm32-dma";
+			reg = <0x40020400 0x400>;
+			interrupts = <56>,
+				     <57>,
+				     <58>,
+				     <59>,
+				     <60>,
+				     <68>,
+				     <69>,
+				     <70>;
+			clocks = <&rcc DMA2_CK>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+			status = "disabled";
+		};
+
+		dmamux1: dma-router@40020800 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x40020800 0x40>;
+			#dma-cells = <3>;
+			dma-channels = <16>;
+			dma-requests = <128>;
+			dma-masters = <&dma1 &dma2>;
+			clocks = <&rcc DMA1_CK>;
+		};
+
+		adc_12: adc@40022000 {
+			compatible = "st,stm32h7-adc-core";
+			reg = <0x40022000 0x400>;
+			interrupts = <18>;
+			clocks = <&rcc ADC12_CK>;
+			clock-names = "bus";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc1: adc@0 {
+				compatible = "st,stm32h7-adc";
+				#io-channel-cells = <1>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_12>;
+				interrupts = <0>;
+				status = "disabled";
+			};
+
+			adc2: adc@100 {
+				compatible = "st,stm32h7-adc";
+				#io-channel-cells = <1>;
+				reg = <0x100>;
+				interrupt-parent = <&adc_12>;
+				interrupts = <1>;
+				status = "disabled";
+			};
+		};
+
+		usbotg_hs: usb@40040000 {
+			compatible = "st,stm32f7-hsotg";
+			reg = <0x40040000 0x40000>;
+			interrupts = <77>;
+			clocks = <&rcc USB1OTG_CK>;
+			clock-names = "otg";
+			g-rx-fifo-size = <256>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
+			status = "disabled";
+		};
+
+		usbotg_fs: usb@40080000 {
+			compatible = "st,stm32f4x9-fsotg";
+			reg = <0x40080000 0x40000>;
+			interrupts = <101>;
+			clocks = <&rcc USB2OTG_CK>;
+			clock-names = "otg";
+			status = "disabled";
+		};
+
+		ltdc: display-controller@50001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x50001000 0x200>;
+			interrupts = <88>, <89>;
+			resets = <&rcc STM32H7_APB3_RESET(LTDC)>;
+			clocks = <&rcc LTDC_CK>;
+			clock-names = "lcd";
+			status = "disabled";
+		};
+
+		mdma1: dma-controller@52000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x52000000 0x1000>;
+			interrupts = <122>;
+			clocks = <&rcc MDMA_CK>;
+			#dma-cells = <5>;
+			dma-channels = <16>;
+			dma-requests = <32>;
+		};
+
+		sdmmc1: mmc@52007000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x10153180>;
+			reg = <0x52007000 0x1000>;
+			interrupts = <49>;
+			clocks = <&rcc SDMMC1_CK>;
+			clock-names = "apb_pclk";
+			resets = <&rcc STM32H7_AHB3_RESET(SDMMC1)>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+		};
+
+		sdmmc2: mmc@48022400 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x10153180>;
+			reg = <0x48022400 0x400>;
+			interrupts = <124>;
+			clocks = <&rcc SDMMC2_CK>;
+			clock-names = "apb_pclk";
+			resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		exti: interrupt-controller@58000000 {
+			compatible = "st,stm32h7-exti";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x58000000 0x400>;
+			interrupts = <1>, <2>, <3>, <6>, <7>, <8>, <9>, <10>, <23>, <40>, <41>, <62>, <76>;
+		};
+
+		syscfg: syscon@58000400 {
+			compatible = "st,stm32-syscfg", "syscon";
+			reg = <0x58000400 0x400>;
+		};
+
+		spi6: spi@58001400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x58001400 0x400>;
+			interrupts = <86>;
+			resets = <&rcc STM32H7_APB4_RESET(SPI6)>;
+			clocks = <&rcc SPI6_CK>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@58001c00 {
+			compatible = "st,stm32f7-i2c";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x58001C00 0x400>;
+			interrupts = <95>,
+				     <96>;
+			resets = <&rcc STM32H7_APB4_RESET(I2C4)>;
+			clocks = <&rcc I2C4_CK>;
+			status = "disabled";
+		};
+
+		lptimer2: timer@58002400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x58002400 0x400>;
+			clocks = <&rcc LPTIM2_CK>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@1 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		lptimer3: timer@58002800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x58002800 0x400>;
+			clocks = <&rcc LPTIM3_CK>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@2 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		lptimer4: timer@58002c00 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x58002c00 0x400>;
+			clocks = <&rcc LPTIM4_CK>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		lptimer5: timer@58003000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x58003000 0x400>;
+			clocks = <&rcc LPTIM5_CK>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		vrefbuf: regulator@58003c00 {
+			compatible = "st,stm32-vrefbuf";
+			reg = <0x58003C00 0x8>;
+			clocks = <&rcc VREF_CK>;
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <2500000>;
+			status = "disabled";
+		};
+
+		rtc: rtc@58004000 {
+			compatible = "st,stm32h7-rtc";
+			reg = <0x58004000 0x400>;
+			clocks = <&rcc RTCAPB_CK>, <&rcc RTC_CK>;
+			clock-names = "pclk", "rtc_ck";
+			assigned-clocks = <&rcc RTC_CK>;
+			assigned-clock-parents = <&rcc LSE_CK>;
+			interrupt-parent = <&exti>;
+			interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+			st,syscfg = <&pwrcfg 0x00 0x100>;
+			status = "disabled";
+		};
+
+		rcc: reset-clock-controller@58024400 {
+			compatible = "st,stm32h743-rcc", "st,stm32-rcc";
+			reg = <0x58024400 0x400>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s>;
+			st,syscfg = <&pwrcfg>;
+		};
+
+		pwrcfg: power-config@58024800 {
+			compatible = "st,stm32-power-config", "syscon";
+			reg = <0x58024800 0x400>;
+		};
+
+		adc_3: adc@58026000 {
+			compatible = "st,stm32h7-adc-core";
+			reg = <0x58026000 0x400>;
+			interrupts = <127>;
+			clocks = <&rcc ADC3_CK>;
+			clock-names = "bus";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc3: adc@0 {
+				compatible = "st,stm32h7-adc";
+				#io-channel-cells = <1>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_3>;
+				interrupts = <0>;
+				status = "disabled";
+			};
+		};
+
+		mac: ethernet@40028000 {
+			compatible = "st,stm32-dwmac", "snps,dwmac-4.10a";
+			reg = <0x40028000 0x8000>;
+			reg-names = "stmmaceth";
+			interrupts = <61>;
+			interrupt-names = "macirq";
+			clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
+			clocks = <&rcc ETH1MAC_CK>, <&rcc ETH1TX_CK>, <&rcc ETH1RX_CK>;
+			st,syscon = <&syscfg 0x4>;
+			snps,pbl = <8>;
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@58020000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32h743-pinctrl";
+			ranges = <0 0x58020000 0x3000>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&syscfg 0x8>;
+
+			gpioa: gpio@58020000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA_CK>;
+				st,bank-name = "GPIOA";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio@58020400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x400 0x400>;
+				clocks = <&rcc GPIOB_CK>;
+				st,bank-name = "GPIOB";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio@58020800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x800 0x400>;
+				clocks = <&rcc GPIOC_CK>;
+				st,bank-name = "GPIOC";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio@58020c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0xc00 0x400>;
+				clocks = <&rcc GPIOD_CK>;
+				st,bank-name = "GPIOD";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio@58021000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOE_CK>;
+				st,bank-name = "GPIOE";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio@58021400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1400 0x400>;
+				clocks = <&rcc GPIOF_CK>;
+				st,bank-name = "GPIOF";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio@58021800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1800 0x400>;
+				clocks = <&rcc GPIOG_CK>;
+				st,bank-name = "GPIOG";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio@58021c00 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x1c00 0x400>;
+				clocks = <&rcc GPIOH_CK>;
+				st,bank-name = "GPIOH";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 112 16>;
+			};
+
+			gpioi: gpio@58022000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOI_CK>;
+				st,bank-name = "GPIOI";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 128 16>;
+			};
+
+			gpioj: gpio@58022400 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2400 0x400>;
+				clocks = <&rcc GPIOJ_CK>;
+				st,bank-name = "GPIOJ";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 144 16>;
+			};
+
+			gpiok: gpio@58022800 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x2800 0x400>;
+				clocks = <&rcc GPIOK_CK>;
+				st,bank-name = "GPIOK";
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 160 8>;
+			};
+		};
+	};
+};
+
+&systick {
+	clock-frequency = <250000000>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32h743i-disco.dts b/arch/arm/boot/dts/st/stm32h743i-disco.dts
new file mode 100644
index 000000000000..2b452883a708
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h743i-disco.dts
@@ -0,0 +1,111 @@
+/*
+ * Copyright 2017 - Patrice Chotard <patrice.chotard@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32h743.dtsi"
+#include "stm32h7-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32H743i-Discovery board";
+	compatible = "st,stm32h743i-disco", "st,stm32h743";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@d0000000 {
+		device_type = "memory";
+		reg = <0xd0000000 0x2000000>;
+	};
+
+	aliases {
+		serial0 = &usart2;
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&mac {
+	status = "disabled";
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-0 = <&usart2_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32h743i-eval.dts b/arch/arm/boot/dts/st/stm32h743i-eval.dts
new file mode 100644
index 000000000000..5c5d8059bdc7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h743i-eval.dts
@@ -0,0 +1,160 @@
+/*
+ * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "stm32h743.dtsi"
+#include "stm32h7-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32H743i-EVAL board";
+	compatible = "st,stm32h743i-eval", "st,stm32h743";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@d0000000 {
+		device_type = "memory";
+		reg = <0xd0000000 0x2000000>;
+	};
+
+	aliases {
+		serial0 = &usart1;
+	};
+
+	vdda: regulator-vdda {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v2v9_sd: regulator-v2v9_sd {
+		compatible = "regulator-fixed";
+		regulator-name = "v2v9_sd";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-always-on;
+	};
+
+	usbotg_hs_phy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		clocks = <&rcc USB1ULPI_CK>;
+		clock-names = "main_clk";
+	};
+};
+
+&adc_12 {
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+	adc1: adc@0 {
+		/* potentiometer */
+		st,adc-channels = <0>;
+		status = "okay";
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-names = "default";
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&mac {
+	status = "disabled";
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&v2v9_sd>;
+	status = "okay";
+};
+
+&usart1 {
+	pinctrl-0 = <&usart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbotg_hs_phy>;
+	phy-names = "usb2-phy";
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32h750.dtsi b/arch/arm/boot/dts/st/stm32h750.dtsi
new file mode 100644
index 000000000000..41e3b1e3a874
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h750.dtsi
@@ -0,0 +1,6 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */
+
+#include "stm32h743.dtsi"
+
+
diff --git a/arch/arm/boot/dts/st/stm32h750i-art-pi.dts b/arch/arm/boot/dts/st/stm32h750i-art-pi.dts
new file mode 100644
index 000000000000..44c307f8b09c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32h750i-art-pi.dts
@@ -0,0 +1,229 @@
+/*
+ * Copyright 2021 - Dillon Min <dillon.minfei@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * For art-pi board resources, you can refer to link:
+ * 	https://art-pi.gitee.io/website/
+ */
+
+/dts-v1/;
+#include "stm32h750.dtsi"
+#include "stm32h7-pinctrl.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "RT-Thread STM32H750i-ART-PI board";
+	compatible = "st,stm32h750i-art-pi", "st,stm32h750";
+
+	chosen {
+		bootargs = "root=/dev/ram";
+		stdout-path = "serial0:2000000n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x2000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			no-map;
+			size = <0x100000>;
+			linux,dma-default;
+		};
+	};
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-red {
+			gpios = <&gpioi 8 0>;
+		};
+		led-green {
+			gpios = <&gpioc 15 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&clk_hse {
+	clock-frequency = <25000000>;
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&mac {
+	status = "disabled";
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>;
+	dmas = <&dmamux1 37 0x400 0x05>,
+	       <&dmamux1 38 0x400 0x05>;
+	dma-names = "rx", "tx";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+
+		partition@0 {
+			label = "root filesystem";
+			reg = <0 0x1000000>;
+		};
+	};
+};
+
+&usart2 {
+	pinctrl-0 = <&usart2_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins>;
+	dmas = <&dmamux1 45 0x400 0x05>,
+	       <&dmamux1 46 0x400 0x05>;
+	dma-names = "rx", "tx";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>;
+		max-speed = <115200>;
+	};
+};
+
+&uart4 {
+	pinctrl-0 = <&uart4_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+
diff --git a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
new file mode 100644
index 000000000000..27e0c3826789
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com>
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	adc1_usb_cc_pins_a: adc1-usb-cc-pins-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('A', 3, ANALOG)>; /* ADC1 in12 */
+		};
+	};
+
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c1_sleep_pins_a: i2c1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	i2c5_pins_a: i2c5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c5_sleep_pins_a: i2c5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, ANALOG)>; /* I2C5_SDA */
+		};
+	};
+
+	mcp23017_pins_a: mcp23017-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	pwm3_pins_a: pwm3-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 1, AF2)>; /* TIM3_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm3_sleep_pins_a: pwm3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 1, ANALOG)>; /* TIM3_CH4 */
+		};
+	};
+
+	pwm4_pins_a: pwm4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF2)>; /* TIM4_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm4_sleep_pins_a: pwm4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>; /* TIM4_CH2 */
+		};
+	};
+
+	pwm8_pins_a: pwm8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 5, AF3)>; /* TIM8_CH3 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm8_sleep_pins_a: pwm8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 5, ANALOG)>; /* TIM8_CH3 */
+		};
+	};
+
+	pwm14_pins_a: pwm14-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 9, AF9)>; /* TIM14_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm14_sleep_pins_a: pwm14-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 9, ANALOG)>; /* TIM14_CH1 */
+		};
+	};
+
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_clk_pins_a: sdmmc1-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	sdmmc2_clk_pins_a: sdmmc2-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 3, AF10)>; /* SDMMC2_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 7, AF6)>, /* SPI5_SCK */
+				 <STM32_PINMUX('H', 3, AF5)>; /* SPI5_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
+	spi5_sleep_pins_a: spi5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 7, ANALOG)>, /* SPI5_SCK */
+				 <STM32_PINMUX('A', 8, ANALOG)>, /* SPI5_MISO */
+				 <STM32_PINMUX('H', 3, ANALOG)>; /* SPI5_MOSI */
+		};
+	};
+
+	stm32g0_intn_pins_a: stm32g0-intn-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	uart4_pins_a: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 6, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_a: uart4-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 6, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 8, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_a: uart4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 6, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('D', 8, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	uart8_pins_a: uart8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart8_idle_pins_a: uart8-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, ANALOG)>; /* UART8_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 9, AF8)>; /* UART8_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart8_sleep_pins_a: uart8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 1, ANALOG)>, /* UART8_TX */
+				 <STM32_PINMUX('F', 9, ANALOG)>; /* UART8_RX */
+		};
+	};
+
+	usart1_pins_a: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 0, AF7)>, /* USART1_TX */
+				 <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 0, AF4)>, /* USART1_RX */
+				 <STM32_PINMUX('A', 7, AF7)>; /* USART1_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart1_idle_pins_a: usart1-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* USART1_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 2, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 0, AF4)>; /* USART1_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart1_sleep_pins_a: usart1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 7, ANALOG)>, /* USART1_CTS_NSS */
+				 <STM32_PINMUX('B', 0, ANALOG)>; /* USART1_RX */
+		};
+	};
+
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 12, AF1)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 15, AF1)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 11, AF2)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart2_idle_pins_a: usart2-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 4, AF3)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 15, AF1)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 12, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 11, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi
new file mode 100644
index 000000000000..d163c267e34c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp131.dtsi
@@ -0,0 +1,1510 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp13-clks.h>
+#include <dt-bindings/reset/stm32mp13-resets.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
+	};
+
+	firmware {
+		optee {
+			method = "smc";
+			compatible = "linaro,optee-tz";
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+			shmem = <&scmi_shm>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+
+	intc: interrupt-controller@a0021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0xa0021000 0x1000>,
+		      <0xa0022000 0x2000>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&intc>;
+		always-on;
+	};
+
+	/* PWR 1v1, 1v8 and 3v3 regulators defined as fixed, waiting for SCMI */
+	reg11: reg11 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg11";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+	};
+
+	reg18: reg18 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	usb33: usb33 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		scmi_sram: sram@2ffff000 {
+			compatible = "mmio-sram";
+			reg = <0x2ffff000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x2ffff000 0x1000>;
+
+			scmi_shm: scmi-sram@0 {
+				compatible = "arm,scmi-shmem";
+				reg = <0 0x80>;
+			};
+		};
+
+		timers2: timer@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM2_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 18 0x400 0x1>,
+			       <&dmamux1 19 0x400 0x1>,
+			       <&dmamux1 20 0x400 0x1>,
+			       <&dmamux1 21 0x400 0x1>,
+			       <&dmamux1 22 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers3: timer@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM3_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 23 0x400 0x1>,
+			       <&dmamux1 24 0x400 0x1>,
+			       <&dmamux1 25 0x400 0x1>,
+			       <&dmamux1 26 0x400 0x1>,
+			       <&dmamux1 27 0x400 0x1>,
+			       <&dmamux1 28 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers4: timer@40002000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM4_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 29 0x400 0x1>,
+			       <&dmamux1 30 0x400 0x1>,
+			       <&dmamux1 31 0x400 0x1>,
+			       <&dmamux1 32 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers5: timer@40003000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40003000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM5_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 55 0x400 0x1>,
+			       <&dmamux1 56 0x400 0x1>,
+			       <&dmamux1 57 0x400 0x1>,
+			       <&dmamux1 58 0x400 0x1>,
+			       <&dmamux1 59 0x400 0x1>,
+			       <&dmamux1 60 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers6: timer@40004000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40004000 0x400>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM6_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 69 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timer@40005000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40005000 0x400>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM7_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 70 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		lptimer1: timer@40009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x40009000 0x400>;
+			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM1_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@0 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		i2s2: audio-controller@4000b000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4000b000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi2: spi@4000b000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI2_K>;
+			resets = <&rcc SPI2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s3: audio-controller@4000c000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4000c000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi3: spi@4000c000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI3_K>;
+			resets = <&rcc SPI3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spdifrx: audio-controller@4000d000 {
+			compatible = "st,stm32h7-spdifrx";
+			reg = <0x4000d000 0x400>;
+			#sound-dai-cells = <0>;
+			clocks = <&rcc SPDIF_K>;
+			clock-names = "kclk";
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 93 0x400 0x01>,
+			       <&dmamux1 94 0x400 0x01>;
+			dma-names = "rx", "rx-ctrl";
+			status = "disabled";
+		};
+
+		usart3: serial@4000f000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000f000 0x400>;
+			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART3_K>;
+			resets = <&rcc USART3_R>;
+			wakeup-source;
+			dmas = <&dmamux1 45 0x400 0x5>,
+			       <&dmamux1 46 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart4: serial@40010000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40010000 0x400>;
+			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART4_K>;
+			resets = <&rcc UART4_R>;
+			wakeup-source;
+			dmas = <&dmamux1 63 0x400 0x5>,
+			       <&dmamux1 64 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart5: serial@40011000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART5_K>;
+			resets = <&rcc UART5_R>;
+			wakeup-source;
+			dmas = <&dmamux1 65 0x400 0x5>,
+			       <&dmamux1 66 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c1: i2c@40012000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40012000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C1_K>;
+			resets = <&rcc I2C1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 33 0x400 0x1>,
+			       <&dmamux1 34 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x1>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40013000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40013000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C2_K>;
+			resets = <&rcc I2C2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 35 0x400 0x1>,
+			       <&dmamux1 36 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x2>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		uart7: serial@40018000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40018000 0x400>;
+			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART7_K>;
+			resets = <&rcc UART7_R>;
+			wakeup-source;
+			dmas = <&dmamux1 79 0x400 0x5>,
+			       <&dmamux1 80 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart8: serial@40019000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40019000 0x400>;
+			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART8_K>;
+			resets = <&rcc UART8_R>;
+			wakeup-source;
+			dmas = <&dmamux1 81 0x400 0x5>,
+			       <&dmamux1 82 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		timers1: timer@44000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44000000 0x400>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM1_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 11 0x400 0x1>,
+			       <&dmamux1 12 0x400 0x1>,
+			       <&dmamux1 13 0x400 0x1>,
+			       <&dmamux1 14 0x400 0x1>,
+			       <&dmamux1 15 0x400 0x1>,
+			       <&dmamux1 16 0x400 0x1>,
+			       <&dmamux1 17 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers8: timer@44001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44001000 0x400>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM8_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 47 0x400 0x1>,
+			       <&dmamux1 48 0x400 0x1>,
+			       <&dmamux1 49 0x400 0x1>,
+			       <&dmamux1 50 0x400 0x1>,
+			       <&dmamux1 51 0x400 0x1>,
+			       <&dmamux1 52 0x400 0x1>,
+			       <&dmamux1 53 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		usart6: serial@44003000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x44003000 0x400>;
+			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART6_K>;
+			resets = <&rcc USART6_R>;
+			wakeup-source;
+			dmas = <&dmamux1 71 0x400 0x5>,
+			       <&dmamux1 72 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s1: audio-controller@44004000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x44004000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi1: spi@44004000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI1_K>;
+			resets = <&rcc SPI1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		sai1: sai@4400a000 {
+			compatible = "st,stm32h7-sai";
+			reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+			ranges = <0 0x4400a000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI1_R>;
+			status = "disabled";
+
+			sai1a: audio-controller@4400a004 {
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 87 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai1b: audio-controller@4400a024 {
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 88 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		sai2: sai@4400b000 {
+			compatible = "st,stm32h7-sai";
+			reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
+			ranges = <0 0x4400b000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI2_R>;
+			status = "disabled";
+
+			sai2a: audio-controller@4400b004 {
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 89 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai2b: audio-controller@4400b024 {
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				#sound-dai-cells = <0>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 90 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		dfsdm: dfsdm@4400d000 {
+			compatible = "st,stm32mp1-dfsdm";
+			reg = <0x4400d000 0x800>;
+			clocks = <&rcc DFSDM_K>;
+			clock-names = "dfsdm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dfsdm0: filter@0 {
+				compatible = "st,stm32-dfsdm-adc";
+				reg = <0>;
+				#io-channel-cells = <1>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 101 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm1: filter@1 {
+				compatible = "st,stm32-dfsdm-adc";
+				reg = <1>;
+				#io-channel-cells = <1>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 102 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+		};
+
+		dma1: dma-controller@48000000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48000000 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA1>;
+			resets = <&rcc DMA1_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dma2: dma-controller@48001000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48001000 0x400>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA2>;
+			resets = <&rcc DMA2_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dmamux1: dma-router@48002000 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x48002000 0x40>;
+			clocks = <&rcc DMAMUX1>;
+			resets = <&rcc DMAMUX1_R>;
+			#dma-cells = <3>;
+			dma-masters = <&dma1 &dma2>;
+			dma-requests = <128>;
+			dma-channels = <16>;
+		};
+
+		adc_2: adc@48004000 {
+			compatible = "st,stm32mp13-adc-core";
+			reg = <0x48004000 0x400>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc ADC2>, <&rcc ADC2_K>;
+			clock-names = "bus", "adc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc2: adc@0 {
+				compatible = "st,stm32mp13-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_2>;
+				interrupts = <0>;
+				dmas = <&dmamux1 10 0x400 0x80000001>;
+				dma-names = "rx";
+				status = "disabled";
+
+				channel@13 {
+					reg = <13>;
+					label = "vrefint";
+				};
+				channel@14 {
+					reg = <14>;
+					label = "vddcore";
+				};
+				channel@16 {
+					reg = <16>;
+					label = "vddcpu";
+				};
+				channel@17 {
+					reg = <17>;
+					label = "vddq_ddr";
+				};
+			};
+		};
+
+		usbotg_hs: usb@49000000 {
+			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+			reg = <0x49000000 0x40000>;
+			clocks = <&rcc USBO_K>;
+			clock-names = "otg";
+			resets = <&rcc USBO_R>;
+			reset-names = "dwc2";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			g-rx-fifo-size = <512>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+			dr_mode = "otg";
+			otg-rev = <0x200>;
+			usb33d-supply = <&usb33>;
+			status = "disabled";
+		};
+
+		usart1: serial@4c000000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4c000000 0x400>;
+			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART1_K>;
+			resets = <&rcc USART1_R>;
+			wakeup-source;
+			dmas = <&dmamux1 41 0x400 0x5>,
+			       <&dmamux1 42 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		usart2: serial@4c001000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4c001000 0x400>;
+			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART2_K>;
+			resets = <&rcc USART2_R>;
+			wakeup-source;
+			dmas = <&dmamux1 43 0x400 0x5>,
+			       <&dmamux1 44 0x400 0x1>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s4: audio-controller@4c002000 {
+			compatible = "st,stm32h7-i2s";
+			reg = <0x4c002000 0x400>;
+			#sound-dai-cells = <0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi4: spi@4c002000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c002000 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI4_K>;
+			resets = <&rcc SPI4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi5: spi@4c003000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c003000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI5_K>;
+			resets = <&rcc SPI5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 85 0x400 0x01>,
+			       <&dmamux1 86 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c3: i2c@4c004000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c004000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C3_K>;
+			resets = <&rcc I2C3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 73 0x400 0x1>,
+			       <&dmamux1 74 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x4>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c4: i2c@4c005000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c005000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C4_K>;
+			resets = <&rcc I2C4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 75 0x400 0x1>,
+			       <&dmamux1 76 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x8>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c5: i2c@4c006000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c006000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C5_K>;
+			resets = <&rcc I2C5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 115 0x400 0x1>,
+			       <&dmamux1 116 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x10>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		timers12: timer@4c007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c007000 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM12_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timer@4c008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c008000 0x400>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM13_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@12 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <12>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timer@4c009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c009000 0x400>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM14_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@13 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <13>;
+				status = "disabled";
+			};
+		};
+
+		timers15: timer@4c00a000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00a000 0x400>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM15_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 105 0x400 0x1>,
+			       <&dmamux1 106 0x400 0x1>,
+			       <&dmamux1 107 0x400 0x1>,
+			       <&dmamux1 108 0x400 0x1>;
+			dma-names = "ch1", "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@14 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <14>;
+				status = "disabled";
+			};
+		};
+
+		timers16: timer@4c00b000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00b000 0x400>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM16_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 109 0x400 0x1>,
+			       <&dmamux1 110 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@15 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <15>;
+				status = "disabled";
+			};
+		};
+
+		timers17: timer@4c00c000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x4c00c000 0x400>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM17_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 111 0x400 0x1>,
+			       <&dmamux1 112 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@16 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <16>;
+				status = "disabled";
+			};
+		};
+
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp13-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clock-names = "hse", "hsi", "csi", "lse", "lsi";
+			clocks = <&scmi_clk CK_SCMI_HSE>,
+				 <&scmi_clk CK_SCMI_HSI>,
+				 <&scmi_clk CK_SCMI_CSI>,
+				 <&scmi_clk CK_SCMI_LSE>,
+				 <&scmi_clk CK_SCMI_LSI>;
+		};
+
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp13-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
+
+		syscfg: syscon@50020000 {
+			compatible = "st,stm32mp157-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+			clocks = <&rcc SYSCFG>;
+		};
+
+		lptimer2: timer@50021000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50021000 0x400>;
+			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM2_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@1 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer3: timer@50022000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50022000 0x400>;
+			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM3_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@2 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer4: timer@50023000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50023000 0x400>;
+			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM4_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		lptimer5: timer@50024000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50024000 0x400>;
+			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM5_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer {
+				compatible = "st,stm32-lptimer-timer";
+				status = "disabled";
+			};
+		};
+
+		mdma: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
+		};
+
+		fmc: memory-controller@58002000 {
+			compatible = "st,stm32mp1-fmc2-ebi";
+			reg = <0x58002000 0x1000>;
+			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+				 <4 0 0x80000000 0x10000000>; /* NAND */
+			#address-cells = <2>;
+			#size-cells = <1>;
+			clocks = <&rcc FMC_K>;
+			resets = <&rcc FMC_R>;
+			status = "disabled";
+
+			nand-controller@4,0 {
+				compatible = "st,stm32mp1-fmc2-nfc";
+				reg = <4 0x00000000 0x1000>,
+				      <4 0x08010000 0x1000>,
+				      <4 0x08020000 0x1000>,
+				      <4 0x01000000 0x1000>,
+				      <4 0x09010000 0x1000>,
+				      <4 0x09020000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>,
+				       <&mdma 24 0x2 0x12000a08 0x0 0x0>,
+				       <&mdma 25 0x2 0x12000a0a 0x0 0x0>;
+				dma-names = "tx", "rx", "ecc";
+				status = "disabled";
+			};
+		};
+
+		qspi: spi@58003000 {
+			compatible = "st,stm32f469-qspi";
+			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+			reg-names = "qspi", "qspi_mm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>,
+			       <&mdma 26 0x2 0x10100008 0x0 0x0>;
+			dma-names = "tx", "rx";
+			clocks = <&rcc QSPI_K>;
+			resets = <&rcc QSPI_R>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
+			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC1_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <130000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
+			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <130000000>;
+			status = "disabled";
+		};
+
+		usbh_ohci: usb@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		usbh_ehci: usb@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
+			status = "disabled";
+		};
+
+		iwdg2: watchdog@5a002000 {
+			compatible = "st,stm32mp1-iwdg";
+			reg = <0x5a002000 0x400>;
+			clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+			clock-names = "pclk", "lsi";
+			status = "disabled";
+		};
+
+		usbphyc: usbphyc@5a006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
+			status = "disabled";
+
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
+				reg = <0>;
+			};
+
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
+			};
+		};
+
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scmi_clk CK_SCMI_RTCAPB>,
+				 <&scmi_clk CK_SCMI_RTC>;
+			clock-names = "pclk", "rtc_ck";
+			status = "disabled";
+		};
+
+		bsec: efuse@5c005000 {
+			compatible = "st,stm32mp13-bsec";
+			reg = <0x5c005000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			part_number_otp: part_number_otp@4 {
+				reg = <0x4 0x2>;
+				bits = <0 12>;
+			};
+			ts_cal1: calib@5c {
+				reg = <0x5c 0x2>;
+			};
+			ts_cal2: calib@5e {
+				reg = <0x5e 0x2>;
+			};
+		};
+
+		/*
+		 * Break node order to solve dependency probe issue between
+		 * pinctrl and exti.
+		 */
+		pinctrl: pinctrl@50002000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp135-pinctrl";
+			ranges = <0 0x50002000 0x8400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioa: gpio@50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA>;
+				st,bank-name = "GPIOA";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio@50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOB>;
+				st,bank-name = "GPIOB";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio@50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOC>;
+				st,bank-name = "GPIOC";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio@50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&rcc GPIOD>;
+				st,bank-name = "GPIOD";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio@50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&rcc GPIOE>;
+				st,bank-name = "GPIOE";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio@50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&rcc GPIOF>;
+				st,bank-name = "GPIOF";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio@50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&rcc GPIOG>;
+				st,bank-name = "GPIOG";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio@50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&rcc GPIOH>;
+				st,bank-name = "GPIOH";
+				ngpios = <15>;
+				gpio-ranges = <&pinctrl 0 112 15>;
+			};
+
+			gpioi: gpio@5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&rcc GPIOI>;
+				st,bank-name = "GPIOI";
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 128 8>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp133.dtsi b/arch/arm/boot/dts/st/stm32mp133.dtsi
new file mode 100644
index 000000000000..df451c3c2a26
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp133.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp131.dtsi"
+
+/ {
+	soc {
+		m_can1: can@4400e000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		m_can2: can@4400f000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		adc_1: adc@48003000 {
+			compatible = "st,stm32mp13-adc-core";
+			reg = <0x48003000 0x400>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc ADC1>, <&rcc ADC1_K>;
+			clock-names = "bus", "adc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc1: adc@0 {
+				compatible = "st,stm32mp13-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>;
+				interrupt-parent = <&adc_1>;
+				interrupts = <0>;
+				dmas = <&dmamux1 9 0x400 0x80000001>;
+				dma-names = "rx";
+				status = "disabled";
+
+				channel@18 {
+					reg = <18>;
+					label = "vrefint";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135.dtsi b/arch/arm/boot/dts/st/stm32mp135.dtsi
new file mode 100644
index 000000000000..abf2acd37b4e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp135.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp133.dtsi"
+
+/ {
+	soc {
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
new file mode 100644
index 000000000000..f0900ca672b5
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts
@@ -0,0 +1,370 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp135.dtsi"
+#include "stm32mp13xf.dtsi"
+#include "stm32mp13-pinctrl.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP135F-DK Discovery Board";
+	compatible = "st,stm32mp135f-dk", "st,stm32mp135";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart1;
+		serial2 = &uart8;
+		serial3 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		optee@dd000000 {
+			reg = <0xdd000000 0x3000000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-user {
+			label = "User-PA13";
+			linux,code = <BTN_1>;
+			gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	v3v3_sw: v3v3-sw {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3_sw";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_adc: vdd-adc {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_adc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_sd: vdd-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-always-on;
+	};
+
+	vdd_usb: vdd-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&adc_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc1_usb_cc_pins_a>;
+	vdda-supply = <&vdd_adc>;
+	vref-supply = <&vdd_adc>;
+	status = "okay";
+	adc1: adc@0 {
+		status = "okay";
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in6 & in12.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (5.1 + 47kOhms) * 5pF => 1.3us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@12 {
+			reg = <12>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <96>;
+	i2c-scl-falling-time-ns = <3>;
+	clock-frequency = <1000000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	mcp23017: pinctrl@21 {
+		compatible = "microchip,mcp23017";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpiog>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcp23017_pins_a>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		microchip,irq-mirror;
+	};
+
+	typec@53 {
+		compatible = "st,stm32g0-typec";
+		reg = <0x53>;
+		/* Alert pin on PI2 */
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		/* Internal pull-up on PI2 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&stm32g0_intn_pins_a>;
+		firmware-name = "stm32g0-ucsi.mp135f-dk.fw";
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+
+			port {
+				con_usb_c_g0_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <170>;
+	i2c-scl-falling-time-ns = <5>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioh 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a>;
+		pinctrl-1 = <&pwm4_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-1 = <&pwm8_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers14 {
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm14_pins_a>;
+		pinctrl-1 = <&pwm14_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@13 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart8_pins_a>;
+	pinctrl-1 = <&uart8_sleep_pins_a>;
+	pinctrl-2 = <&uart8_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+/* Bluetooth */
+&usart2 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	pinctrl-2 = <&usart2_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3_sw>;
+	};
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usb_c_g0_ep>;
+		};
+	};
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	st,current-boost-microamp = <1000>;
+	st,decrease-hs-slew-rate;
+	st,tune-hs-dc-level = <2>;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <11>;
+	st,trim-hs-impedance = <2>;
+	st,tune-squelch-level = <1>;
+	st,enable-hs-rx-gain-eq;
+	st,no-hs-ftime-ctrl;
+	st,no-lsfs-sc;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	st,current-boost-microamp = <1000>;
+	st,decrease-hs-slew-rate;
+	st,tune-hs-dc-level = <2>;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <11>;
+	st,trim-hs-impedance = <2>;
+	st,tune-squelch-level = <1>;
+	st,enable-hs-rx-gain-eq;
+	st,no-hs-ftime-ctrl;
+	st,no-lsfs-sc;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp13xc.dtsi b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
new file mode 100644
index 000000000000..4d00e7592882
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp: crypto@54002000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54002000 0x400>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp13xf.dtsi b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
new file mode 100644
index 000000000000..4d00e7592882
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp: crypto@54002000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54002000 0x400>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
new file mode 100644
index 000000000000..06e969aa5fdb
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15-pinctrl.dtsi
@@ -0,0 +1,2697 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+&pinctrl {
+	adc1_in6_pins_a: adc1-in6-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>;
+		};
+	};
+
+	adc12_ain_pins_a: adc12-ain-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 3, ANALOG)>, /* ADC1 in13 */
+				 <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('F', 13, ANALOG)>, /* ADC2 in2 */
+				 <STM32_PINMUX('F', 14, ANALOG)>; /* ADC2 in6 */
+		};
+	};
+
+	adc12_ain_pins_b: adc12-ain-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 12, ANALOG)>, /* ADC1 in6 */
+				 <STM32_PINMUX('F', 13, ANALOG)>; /* ADC2 in2 */
+		};
+	};
+
+	adc12_usb_cc_pins_a: adc12-usb-cc-pins-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>, /* ADC12 in18 */
+				 <STM32_PINMUX('A', 5, ANALOG)>; /* ADC12 in19 */
+		};
+	};
+
+	cec_pins_a: cec-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, AF4)>;
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	cec_sleep_pins_a: cec-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 15, ANALOG)>; /* HDMI_CEC */
+		};
+	};
+
+	cec_pins_b: cec-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF5)>;
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	cec_sleep_pins_b: cec-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* HDMI_CEC */
+		};
+	};
+
+	dac_ch1_pins_a: dac-ch1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4, ANALOG)>;
+		};
+	};
+
+	dac_ch2_pins_a: dac-ch2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 5, ANALOG)>;
+		};
+	};
+
+	dcmi_pins_a: dcmi-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 8,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('H', 9,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('H', 12, AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('B', 8,  AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  AF13)>,/* DCMI_D9 */
+				 <STM32_PINMUX('I', 3,  AF13)>,/* DCMI_D10 */
+				 <STM32_PINMUX('H', 15, AF13)>;/* DCMI_D11 */
+			bias-disable;
+		};
+	};
+
+	dcmi_sleep_pins_a: dcmi-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 8,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('H', 9,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('H', 12, ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('B', 8,  ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  ANALOG)>,/* DCMI_D9 */
+				 <STM32_PINMUX('I', 3,  ANALOG)>,/* DCMI_D10 */
+				 <STM32_PINMUX('H', 15, ANALOG)>;/* DCMI_D11 */
+		};
+	};
+
+	dcmi_pins_b: dcmi-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  AF13)>;/* DCMI_D7 */
+			bias-disable;
+		};
+	};
+
+	dcmi_sleep_pins_b: dcmi-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('C', 6,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1,  ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('E', 11, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('D', 3,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('E', 13, ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('B', 9,  ANALOG)>;/* DCMI_D7 */
+		};
+	};
+
+	dcmi_pins_c: dcmi-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  AF13)>;/* DCMI_D9 */
+			bias-pull-up;
+		};
+	};
+
+	dcmi_sleep_pins_c: dcmi-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  ANALOG)>;/* DCMI_D9 */
+		};
+	};
+
+	ethernet0_rgmii_pins_a: rgmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rgmii_sleep_pins_a: rgmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('B', 0, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	ethernet0_rgmii_pins_b: rgmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rgmii_sleep_pins_b: rgmii-sleep-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		 };
+	};
+
+	ethernet0_rgmii_pins_c: rgmii-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rgmii_sleep_pins_c: rgmii-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	ethernet0_rgmii_pins_d: rgmii-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 13, AF11)>,	/* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>,	/* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, AF11)>,	/* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rgmii_sleep_pins_d: rgmii-sleep-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+				 <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+				 <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+				 <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+				 <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+		};
+	};
+
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF0)>,   /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_sleep_pins_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	ethernet0_rmii_pins_b: rmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 5, AF0)>, /* ETH1_CLK */
+				<STM32_PINMUX('C', 1, AF11)>, /* ETH1_MDC */
+				<STM32_PINMUX('G', 13, AF11)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, AF11)>; /* ETH1_TXD1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH1_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('A', 7, AF11)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('C', 4, AF11)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, AF11)>; /* ETH1_RXD1 */
+			bias-disable;
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('B', 11, AF11)>; /* ETH1_TX_EN */
+		};
+	};
+
+	ethernet0_rmii_sleep_pins_b: rmii-sleep-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+				<STM32_PINMUX('A', 7, ANALOG)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('B', 5, ANALOG)>, /* ETH1_CLK */
+				<STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_TX_EN */
+				<STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+				<STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RXD1 */
+				<STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, ANALOG)>; /* ETH1_TXD1 */
+		};
+	};
+
+	ethernet0_rmii_pins_c: rmii-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_sleep_pins_c: rmii-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
+	fmc_pins_a: fmc-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, AF12)>, /* FMC_NWE */
+				 <STM32_PINMUX('D', 11, AF12)>, /* FMC_A16_FMC_CLE */
+				 <STM32_PINMUX('D', 12, AF12)>, /* FMC_A17_FMC_ALE */
+				 <STM32_PINMUX('D', 14, AF12)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, AF12)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, AF12)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, AF12)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, AF12)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, AF12)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, AF12)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, AF12)>, /* FMC_D7 */
+				 <STM32_PINMUX('G', 9, AF12)>; /* FMC_NE2_FMC_NCE */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF12)>; /* FMC_NWAIT */
+			bias-pull-up;
+		};
+	};
+
+	fmc_sleep_pins_a: fmc-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* FMC_NWE */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* FMC_A16_FMC_CLE */
+				 <STM32_PINMUX('D', 12, ANALOG)>, /* FMC_A17_FMC_ALE */
+				 <STM32_PINMUX('D', 14, ANALOG)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, ANALOG)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, ANALOG)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, ANALOG)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, ANALOG)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, ANALOG)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, ANALOG)>, /* FMC_D7 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* FMC_NWAIT */
+				 <STM32_PINMUX('G', 9, ANALOG)>; /* FMC_NE2_FMC_NCE */
+		};
+	};
+
+	fmc_pins_b: fmc-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, AF12)>, /* FMC_NWE */
+				 <STM32_PINMUX('B', 7, AF12)>, /* FMC_NL */
+				 <STM32_PINMUX('D', 14, AF12)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, AF12)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, AF12)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, AF12)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, AF12)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, AF12)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, AF12)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, AF12)>, /* FMC_D7 */
+				 <STM32_PINMUX('E', 11, AF12)>, /* FMC_D8 */
+				 <STM32_PINMUX('E', 12, AF12)>, /* FMC_D9 */
+				 <STM32_PINMUX('E', 13, AF12)>, /* FMC_D10 */
+				 <STM32_PINMUX('E', 14, AF12)>, /* FMC_D11 */
+				 <STM32_PINMUX('E', 15, AF12)>, /* FMC_D12 */
+				 <STM32_PINMUX('D', 8, AF12)>, /* FMC_D13 */
+				 <STM32_PINMUX('D', 9, AF12)>, /* FMC_D14 */
+				 <STM32_PINMUX('D', 10, AF12)>, /* FMC_D15 */
+				 <STM32_PINMUX('G', 9, AF12)>, /* FMC_NE2_FMC_NCE */
+				 <STM32_PINMUX('G', 12, AF12)>; /* FMC_NE4 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+
+	fmc_sleep_pins_b: fmc-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 4, ANALOG)>, /* FMC_NOE */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* FMC_NWE */
+				 <STM32_PINMUX('B', 7, ANALOG)>, /* FMC_NL */
+				 <STM32_PINMUX('D', 14, ANALOG)>, /* FMC_D0 */
+				 <STM32_PINMUX('D', 15, ANALOG)>, /* FMC_D1 */
+				 <STM32_PINMUX('D', 0, ANALOG)>, /* FMC_D2 */
+				 <STM32_PINMUX('D', 1, ANALOG)>, /* FMC_D3 */
+				 <STM32_PINMUX('E', 7, ANALOG)>, /* FMC_D4 */
+				 <STM32_PINMUX('E', 8, ANALOG)>, /* FMC_D5 */
+				 <STM32_PINMUX('E', 9, ANALOG)>, /* FMC_D6 */
+				 <STM32_PINMUX('E', 10, ANALOG)>, /* FMC_D7 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* FMC_D8 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* FMC_D9 */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* FMC_D10 */
+				 <STM32_PINMUX('E', 14, ANALOG)>, /* FMC_D11 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* FMC_D12 */
+				 <STM32_PINMUX('D', 8, ANALOG)>, /* FMC_D13 */
+				 <STM32_PINMUX('D', 9, ANALOG)>, /* FMC_D14 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* FMC_D15 */
+				 <STM32_PINMUX('G', 9, ANALOG)>, /* FMC_NE2_FMC_NCE */
+				 <STM32_PINMUX('G', 12, ANALOG)>; /* FMC_NE4 */
+		};
+	};
+
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c1_sleep_pins_a: i2c1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	i2c1_pins_b: i2c1-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 14, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c1_sleep_pins_b: i2c1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 14, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('F', 15, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	i2c2_pins_a: i2c2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c2_sleep_pins_a: i2c2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 4, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	i2c2_pins_b1: i2c2-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c2_sleep_pins_b1: i2c2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	i2c2_pins_c: i2c2-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 1, AF4)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c2_pins_sleep_c: i2c2-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 1, ANALOG)>, /* I2C2_SCL */
+				 <STM32_PINMUX('H', 5, ANALOG)>; /* I2C2_SDA */
+		};
+	};
+
+	i2c5_pins_a: i2c5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('A', 12, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c5_sleep_pins_a: i2c5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* I2C5_SDA */
+
+		};
+	};
+
+	i2c5_pins_b: i2c5-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('D', 1, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c5_sleep_pins_b: i2c5-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 0, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('D', 1, ANALOG)>; /* I2C5_SDA */
+		};
+	};
+
+	i2s2_pins_a: i2s2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 9, AF5)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 9, AF5)>; /* I2S2_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	i2s2_sleep_pins_a: i2s2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 3, ANALOG)>, /* I2S2_SDO */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* I2S2_WS */
+				 <STM32_PINMUX('A', 9, ANALOG)>; /* I2S2_CK */
+		};
+	};
+
+	ltdc_pins_a: ltdc-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, AF14)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('F', 10, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('H',  2, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('C',  0, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('E',  6, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('H', 14, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('I',  0, AF14)>, /* LCD_G5 */
+				 <STM32_PINMUX('I',  1, AF14)>, /* LCD_G6 */
+				 <STM32_PINMUX('I',  2, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('I',  4, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('D',  8, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	ltdc_sleep_pins_a: ltdc-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('F', 10, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('H',  2, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('C',  0, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('E',  6, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('H', 14, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('I',  0, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('I',  1, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('I',  2, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('I',  4, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('D',  8, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	ltdc_pins_b: ltdc-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 14, AF14)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 12, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I', 13, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('K',  7, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('I', 15, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('J',  0, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('J',  1, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('J',  2, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('J',  3, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('J',  4, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('J',  5, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('J',  6, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('J',  7, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('J',  8, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('J',  9, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('J', 10, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('J', 11, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('K',  0, AF14)>, /* LCD_G5 */
+				 <STM32_PINMUX('K',  1, AF14)>, /* LCD_G6 */
+				 <STM32_PINMUX('K',  2, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('J', 12, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('J', 13, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('J', 14, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('J', 15, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('K',  3, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('K',  4, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('K',  5, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('K',  6, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	ltdc_sleep_pins_b: ltdc-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 14, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 12, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I', 13, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('K',  7, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('I', 15, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('J',  0, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('J',  1, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('J',  2, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('J',  3, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('J',  4, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('J',  5, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('J',  6, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('J',  7, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('J',  8, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('J',  9, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('J', 10, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('J', 11, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('K',  0, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('K',  1, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('K',  2, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('J', 12, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('J', 13, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('J', 14, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('J', 15, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('K',  3, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('K',  4, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('K',  5, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('K',  6, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	ltdc_pins_c: ltdc-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B',  1, AF9)>,  /* LTDC_R6 */
+				 <STM32_PINMUX('B',  9, AF14)>, /* LTDC_B7 */
+				 <STM32_PINMUX('C',  0, AF14)>, /* LTDC_R5 */
+				 <STM32_PINMUX('D',  3, AF14)>, /* LTDC_G7 */
+				 <STM32_PINMUX('D',  6, AF14)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 11, AF14)>, /* LTDC_G3 */
+				 <STM32_PINMUX('E', 12, AF14)>, /* LTDC_B4 */
+				 <STM32_PINMUX('E', 13, AF14)>, /* LTDC_DE */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LTDC_R7 */
+				 <STM32_PINMUX('H',  4, AF9)>,  /* LTDC_G5 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>, /* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I',  1, AF14)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I',  5, AF14)>, /* LTDC_B5 */
+				 <STM32_PINMUX('I',  6, AF14)>, /* LTDC_B6 */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, AF14)>; /* LTDC_HSYNC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 14, AF14)>; /* LTDC_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	ltdc_sleep_pins_c: ltdc-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 1, ANALOG)>,  /* LTDC_R6 */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* LTDC_B7 */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* LTDC_R5 */
+				 <STM32_PINMUX('D', 3, ANALOG)>, /* LTDC_G7 */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* LTDC_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LTDC_B3 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* LTDC_G3 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* LTDC_B4 */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* LTDC_DE */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LTDC_R7 */
+				 <STM32_PINMUX('H', 4, ANALOG)>,  /* LTDC_G5 */
+				 <STM32_PINMUX('H', 8, ANALOG)>, /* LTDC_R2 */
+				 <STM32_PINMUX('H', 9, ANALOG)>, /* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, ANALOG)>, /* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LTDC_G2 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LTDC_G4 */
+				 <STM32_PINMUX('I', 1, ANALOG)>, /* LTDC_G6 */
+				 <STM32_PINMUX('I', 5, ANALOG)>, /* LTDC_B5 */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* LTDC_B6 */
+				 <STM32_PINMUX('I', 9, ANALOG)>, /* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LTDC_HSYNC */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* LTDC_CLK */
+		};
+	};
+
+	ltdc_pins_d: ltdc-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G',  7, AF14)>; /* LCD_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, AF14)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('E', 13, AF14)>, /* LCD_DE */
+				 <STM32_PINMUX('G', 13, AF14)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, AF14)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, AF14)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, AF14)>, /* LCD_R3 */
+				 <STM32_PINMUX('A',  5, AF14)>, /* LCD_R4 */
+				 <STM32_PINMUX('H', 11, AF14)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, AF14)>, /* LCD_G0 */
+				 <STM32_PINMUX('B',  0, AF14)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */
+				 <STM32_PINMUX('E', 11, AF14)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */
+				 <STM32_PINMUX('H',  4,  AF9)>, /* LCD_G5 */
+				 <STM32_PINMUX('I', 11,  AF9)>, /* LCD_G6 */
+				 <STM32_PINMUX('G',  8, AF14)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, AF14)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */
+				 <STM32_PINMUX('E', 12, AF14)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, AF14)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, AF14)>, /* LCD_B6 */
+				 <STM32_PINMUX('I',  7, AF14)>; /* LCD_B7 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	ltdc_sleep_pins_d: ltdc-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('G',  7, ANALOG)>, /* LCD_CLK */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */
+				 <STM32_PINMUX('I',  9, ANALOG)>, /* LCD_VSYNC */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_DE */
+				 <STM32_PINMUX('G', 13, ANALOG)>, /* LCD_R0 */
+				 <STM32_PINMUX('H',  3, ANALOG)>, /* LCD_R1 */
+				 <STM32_PINMUX('H',  8, ANALOG)>, /* LCD_R2 */
+				 <STM32_PINMUX('H',  9, ANALOG)>, /* LCD_R3 */
+				 <STM32_PINMUX('A',  5, ANALOG)>, /* LCD_R4 */
+				 <STM32_PINMUX('H', 11, ANALOG)>, /* LCD_R5 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */
+				 <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */
+				 <STM32_PINMUX('E',  5, ANALOG)>, /* LCD_G0 */
+				 <STM32_PINMUX('B',  0, ANALOG)>, /* LCD_G1 */
+				 <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* LCD_G3 */
+				 <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */
+				 <STM32_PINMUX('H',  4, ANALOG)>, /* LCD_G5 */
+				 <STM32_PINMUX('I', 11, ANALOG)>, /* LCD_G6 */
+				 <STM32_PINMUX('G',  8, ANALOG)>, /* LCD_G7 */
+				 <STM32_PINMUX('D',  9, ANALOG)>, /* LCD_B0 */
+				 <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */
+				 <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* LCD_B4 */
+				 <STM32_PINMUX('A',  3, ANALOG)>, /* LCD_B5 */
+				 <STM32_PINMUX('B',  8, ANALOG)>, /* LCD_B6 */
+				 <STM32_PINMUX('I',  7, ANALOG)>; /* LCD_B7 */
+		};
+	};
+
+	mco1_pins_a: mco1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, AF2)>; /* MCO1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	mco1_sleep_pins_a: mco1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* MCO1 */
+		};
+	};
+
+	mco2_pins_a: mco2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	mco2_sleep_pins_a: mco2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */
+		};
+	};
+
+	m_can1_pins_a: m-can1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 9, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	m_can1_sleep_pins_a: m_can1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('I', 9, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	m_can1_pins_b: m-can1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 11, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	m_can1_sleep_pins_b: m_can1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('A', 11, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	m_can1_pins_c: m-can1-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	m_can1_sleep_pins_c: m_can1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('H', 14, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
+	m_can2_pins_a: m-can2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF9)>; /* CAN2_RX */
+			bias-disable;
+		};
+	};
+
+	m_can2_sleep_pins_a: m_can2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 13, ANALOG)>, /* CAN2_TX */
+				 <STM32_PINMUX('B', 5, ANALOG)>; /* CAN2_RX */
+		};
+	};
+
+	pwm1_pins_a: pwm1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, AF1)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 14, AF1)>; /* TIM1_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm1_sleep_pins_a: pwm1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>, /* TIM1_CH1 */
+				 <STM32_PINMUX('E', 11, ANALOG)>, /* TIM1_CH2 */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* TIM1_CH4 */
+		};
+	};
+
+	pwm1_pins_b: pwm1-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>; /* TIM1_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm1_sleep_pins_b: pwm1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>; /* TIM1_CH1 */
+		};
+	};
+
+	pwm2_pins_a: pwm2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm2_sleep_pins_a: pwm2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 3, ANALOG)>; /* TIM2_CH4 */
+		};
+	};
+
+	pwm3_pins_a: pwm3-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 7, AF2)>; /* TIM3_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm3_sleep_pins_a: pwm3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 7, ANALOG)>; /* TIM3_CH2 */
+		};
+	};
+
+	pwm3_pins_b: pwm3-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm3_sleep_pins_b: pwm3-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* TIM3_CH2 */
+		};
+	};
+
+	pwm4_pins_a: pwm4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 14, AF2)>, /* TIM4_CH3 */
+				 <STM32_PINMUX('D', 15, AF2)>; /* TIM4_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm4_sleep_pins_a: pwm4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 14, ANALOG)>, /* TIM4_CH3 */
+				 <STM32_PINMUX('D', 15, ANALOG)>; /* TIM4_CH4 */
+		};
+	};
+
+	pwm4_pins_b: pwm4-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF2)>; /* TIM4_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm4_sleep_pins_b: pwm4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>; /* TIM4_CH2 */
+		};
+	};
+
+	pwm5_pins_a: pwm5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, AF2)>; /* TIM5_CH2 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm5_sleep_pins_a: pwm5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, ANALOG)>; /* TIM5_CH2 */
+		};
+	};
+
+	pwm5_pins_b: pwm5-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, AF2)>, /* TIM5_CH2 */
+				 <STM32_PINMUX('H', 12, AF2)>, /* TIM5_CH3 */
+				 <STM32_PINMUX('I', 0, AF2)>; /* TIM5_CH4 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm5_sleep_pins_b: pwm5-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 11, ANALOG)>, /* TIM5_CH2 */
+				 <STM32_PINMUX('H', 12, ANALOG)>, /* TIM5_CH3 */
+				 <STM32_PINMUX('I', 0, ANALOG)>; /* TIM5_CH4 */
+		};
+	};
+
+	pwm8_pins_a: pwm8-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm8_sleep_pins_a: pwm8-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 2, ANALOG)>; /* TIM8_CH4 */
+		};
+	};
+
+	pwm12_pins_a: pwm12-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm12_sleep_pins_a: pwm12-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 6, ANALOG)>; /* TIM12_CH1 */
+		};
+	};
+
+	qspi_clk_pins_a: qspi-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+
+	qspi_clk_sleep_pins_a: qspi-clk-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 10, ANALOG)>; /* QSPI_CLK */
+		};
+	};
+
+	qspi_bk1_pins_a: qspi-bk1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+				 <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+				 <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+				 <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* QSPI_BK1_IO0 */
+				 <STM32_PINMUX('F', 9, ANALOG)>, /* QSPI_BK1_IO1 */
+				 <STM32_PINMUX('F', 7, ANALOG)>, /* QSPI_BK1_IO2 */
+				 <STM32_PINMUX('F', 6, ANALOG)>; /* QSPI_BK1_IO3 */
+		};
+	};
+
+	qspi_bk2_pins_a: qspi-bk2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+				 <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+				 <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+				 <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* QSPI_BK2_IO0 */
+				 <STM32_PINMUX('H', 3, ANALOG)>, /* QSPI_BK2_IO1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* QSPI_BK2_IO2 */
+				 <STM32_PINMUX('G', 7, ANALOG)>; /* QSPI_BK2_IO3 */
+		};
+	};
+
+	qspi_cs1_pins_a: qspi-cs1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	qspi_cs1_sleep_pins_a: qspi-cs1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* QSPI_BK1_NCS */
+		};
+	};
+
+	qspi_cs2_pins_a: qspi-cs2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	qspi_cs2_sleep_pins_a: qspi-cs2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>; /* QSPI_BK2_NCS */
+		};
+	};
+
+	sai2a_pins_a: sai2a-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, AF10)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('I', 6, AF10)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, AF10)>, /* SAI2_FS_A */
+				 <STM32_PINMUX('E', 0, AF10)>; /* SAI2_MCLK_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sai2a_sleep_pins_a: sai2a-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 5, ANALOG)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('I', 6, ANALOG)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, ANALOG)>, /* SAI2_FS_A */
+				 <STM32_PINMUX('E', 0, ANALOG)>; /* SAI2_MCLK_A */
+		};
+	};
+
+	sai2a_pins_b: sai2a-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 6, AF10)>,	/* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, AF10)>,	/* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, AF10)>;	/* SAI2_SCK_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sai2a_sleep_pins_b: sai2a-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 6, ANALOG)>,  /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, ANALOG)>,  /* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, ANALOG)>; /* SAI2_SCK_A */
+		};
+	};
+
+	sai2a_pins_c: sai2a-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, AF10)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('D', 11, AF10)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('D', 12, AF10)>; /* SAI2_FS_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sai2a_sleep_pins_c: sai2a-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 13, ANALOG)>, /* SAI2_SCK_A */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* SAI2_SD_A */
+				 <STM32_PINMUX('D', 12, ANALOG)>; /* SAI2_FS_A */
+		};
+	};
+
+	sai2b_pins_a: sai2b-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('E', 13, AF10)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('E', 14, AF10)>; /* SAI2_MCLK_B */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	sai2b_sleep_pins_a: sai2b-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>, /* SAI2_SD_B */
+				 <STM32_PINMUX('E', 12, ANALOG)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('E', 13, ANALOG)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('E', 14, ANALOG)>; /* SAI2_MCLK_B */
+		};
+	};
+
+	sai2b_pins_b: sai2b-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	sai2b_sleep_pins_b: sai2b-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	sai2b_pins_c: sai2b-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	sai2b_sleep_pins_c: sai2b-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	sai2b_pins_d: sai2b-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 2, AF10)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('C', 0, AF8)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('H', 3, AF10)>; /* SAI2_MCLK_B */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */
+			bias-disable;
+		};
+	};
+
+	sai2b_sleep_pins_d: sai2b-sleep-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* SAI2_SCK_B */
+				 <STM32_PINMUX('C', 0, ANALOG)>, /* SAI2_FS_B */
+				 <STM32_PINMUX('H', 3, ANALOG)>, /* SAI2_MCLK_B */
+				 <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */
+		};
+	};
+
+	sai4a_pins_a: sai4a-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, AF10)>; /* SAI4_SD_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sai4a_sleep_pins_a: sai4a-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* SAI4_SD_A */
+		};
+	};
+
+	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_init_pins_a: sdmmc1-b4-init-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_b4_pins_b: sdmmc1-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, AF8)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_od_pins_b: sdmmc1-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, AF8)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, AF12)>; /* SDMMC1_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_b: sdmmc1-b4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('E', 6, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_dir_pins_a: sdmmc1-dir-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2{
+			pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	sdmmc1_dir_init_pins_a: sdmmc1-dir-init-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	sdmmc1_dir_pins_b: sdmmc1-dir-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2{
+			pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+			bias-pull-up;
+		};
+	};
+
+	sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */
+				 <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */
+				 <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */
+				 <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */
+		};
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	sdmmc2_b4_pins_b: sdmmc2-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_b4_od_pins_b: sdmmc2-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 3, AF9)>; /* SDMMC2_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_d47_pins_a: sdmmc2-d47-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_a: sdmmc2-d47-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_pins_b: sdmmc2-d47-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>,  /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_pins_c: sdmmc2-d47-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_c: sdmmc2-d47-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_pins_d: sdmmc2-d47-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_d: sdmmc2-d47-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('E', 5, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc2_d47_pins_e: sdmmc2-d47-4 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, AF9)>,	/* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, AF10)>,	/* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, AF10)>,	/* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, AF9)>;	/* SDMMC2_D7 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_d47_sleep_pins_e: sdmmc2-d47-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+				 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+				 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+		};
+	};
+
+	sdmmc3_b4_pins_a: sdmmc3-b4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, AF9)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('F', 1, AF9)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc3_b4_od_pins_a: sdmmc3-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, AF9)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('F', 1, AF9)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc3_b4_sleep_pins_a: sdmmc3-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('F', 5, ANALOG)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+				 <STM32_PINMUX('F', 1, ANALOG)>; /* SDMMC3_CMD */
+		};
+	};
+
+	sdmmc3_b4_pins_b: sdmmc3-b4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc3_b4_od_pins_b: sdmmc3-b4-od-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */
+			slew-rate = <2>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc3_b4_sleep_pins_b: sdmmc3-b4-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */
+				 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+				 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+				 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+				 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+		};
+	};
+
+	spdifrx_pins_a: spdifrx-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
+			bias-disable;
+		};
+	};
+
+	spdifrx_sleep_pins_a: spdifrx-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 12, ANALOG)>; /* SPDIF_IN1 */
+		};
+	};
+
+	spi1_pins_b: spi1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 5, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('B', 5, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 6, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	spi2_pins_a: spi2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-disable;
+		};
+	};
+
+	spi2_pins_b: spi2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-disable;
+		};
+	};
+
+	spi4_pins_a: spi4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 12, AF5)>, /* SPI4_SCK */
+				 <STM32_PINMUX('E', 6, AF5)>;  /* SPI4_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 13, AF5)>; /* SPI4_MISO */
+			bias-disable;
+		};
+	};
+
+	stusb1600_pins_a: stusb1600-0 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 11, GPIO)>;
+			bias-pull-up;
+		};
+	};
+
+	uart4_pins_a: uart4-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_a: uart4-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_a: uart4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	uart4_pins_b: uart4-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 1, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_pins_c: uart4-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_pins_d: uart4-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_d: uart4-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_d: uart4-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	uart5_pins_a: uart5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF12)>; /* UART5_RX */
+			bias-disable;
+		};
+	};
+
+	uart7_pins_a: uart7-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>, /* UART7_RX */
+				 <STM32_PINMUX('E', 10, AF7)>, /* UART7_CTS */
+				 <STM32_PINMUX('E', 9, AF7)>; /* UART7_RTS */
+			bias-disable;
+		};
+	};
+
+	uart7_pins_b: uart7-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 6, AF7)>; /* UART7_RX */
+			bias-disable;
+		};
+	};
+
+	uart7_pins_c: uart7-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart7_idle_pins_c: uart7-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>; /* UART7_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
+			bias-pull-up;
+		};
+	};
+
+	uart7_sleep_pins_c: uart7-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 8, ANALOG)>, /* UART7_TX */
+				 <STM32_PINMUX('E', 7, ANALOG)>; /* UART7_RX */
+		};
+	};
+
+	uart8_pins_a: uart8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 0, AF8)>; /* UART8_RX */
+			bias-disable;
+		};
+	};
+
+	uart8_rtscts_pins_a: uart8rtscts-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 7, AF8)>, /* UART8_RTS */
+				 <STM32_PINMUX('G', 10, AF8)>; /* UART8_CTS */
+			bias-disable;
+		};
+	};
+
+	usart1_pins_a: usart1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, AF7)>; /* USART1_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart1_idle_pins_a: usart1-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 11, AF7)>; /* USART1_CTS_NSS */
+		};
+	};
+
+	usart1_sleep_pins_a: usart1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 12, ANALOG)>, /* USART1_RTS */
+				 <STM32_PINMUX('A', 11, ANALOG)>; /* USART1_CTS_NSS */
+		};
+	};
+
+	usart2_pins_a: usart2-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_a: usart2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	usart2_pins_b: usart2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 1, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 4, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 15, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_b: usart2-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('E', 15, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	usart2_pins_c: usart2-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, AF7)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart2_idle_pins_c: usart2-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */
+			bias-disable;
+		};
+	};
+
+	usart2_sleep_pins_c: usart2-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */
+				 <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */
+				 <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */
+				 <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */
+		};
+	};
+
+	usart3_pins_a: usart3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_idle_pins_a: usart3-idle-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>; /* USART3_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_sleep_pins_a: usart3-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usart3_pins_b: usart3-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart3_idle_pins_b: usart3-idle-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart3_sleep_pins_b: usart3-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('I', 10, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usart3_pins_c: usart3-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+				 <STM32_PINMUX('B', 13, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart3_idle_pins_c: usart3-idle-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart3_sleep_pins_c: usart3-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('B', 13, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usart3_pins_d: usart3-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart3_idle_pins_d: usart3-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_sleep_pins_d: usart3-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('D', 9, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usart3_pins_e: usart3-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart3_idle_pins_e: usart3-idle-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart3_sleep_pins_e: usart3-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 11, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usbotg_hs_pins_a: usbotg-hs-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
+		};
+	};
+
+	usbotg_fs_dp_dm_pins_a: usbotg-fs-dp-dm-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* OTG_FS_DM */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* OTG_FS_DP */
+		};
+	};
+};
+
+&pinctrl_z {
+	i2c2_pins_b2: i2c2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, AF3)>; /* I2C2_SCL */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c2_sleep_pins_b2: i2c2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, ANALOG)>; /* I2C2_SCL */
+		};
+	};
+
+	i2c4_pins_a: i2c4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
+				 <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c4_sleep_pins_a: i2c4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 4, ANALOG)>, /* I2C4_SCL */
+				 <STM32_PINMUX('Z', 5, ANALOG)>; /* I2C4_SDA */
+		};
+	};
+
+	i2c6_pins_a: i2c6-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 6, AF2)>, /* I2C6_SCL */
+				 <STM32_PINMUX('Z', 7, AF2)>; /* I2C6_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c6_sleep_pins_a: i2c6-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 6, ANALOG)>, /* I2C6_SCL */
+				 <STM32_PINMUX('Z', 7, ANALOG)>; /* I2C6_SDA */
+		};
+	};
+
+	spi1_pins_a: spi1-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 0, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('Z', 2, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 1, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
+
+	spi1_sleep_pins_a: spi1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 0, ANALOG)>, /* SPI1_SCK */
+				 <STM32_PINMUX('Z', 1, ANALOG)>, /* SPI1_MISO */
+				 <STM32_PINMUX('Z', 2, ANALOG)>; /* SPI1_MOSI */
+		};
+	};
+
+	usart1_pins_b: usart1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 7, AF7)>; /* USART1_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	usart1_idle_pins_b: usart1-idle-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('Z', 7, ANALOG)>; /* USART1_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('Z', 6, AF7)>; /* USART1_RX */
+			bias-disable;
+		};
+	};
+
+	usart1_sleep_pins_b: usart1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('Z', 7, ANALOG)>, /* USART1_TX */
+				 <STM32_PINMUX('Z', 6, ANALOG)>; /* USART1_RX */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi b/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi
new file mode 100644
index 000000000000..543f24c2f4f6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15-scmi.dtsi
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	firmware {
+		optee: optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+			shmem = <&scmi_shm>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+
+			scmi_voltd: protocol@17 {
+				reg = <0x17>;
+
+				scmi_reguls: regulators {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					scmi_reg11: reg11@0 {
+						reg = <0>;
+						regulator-name = "reg11";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <1100000>;
+					};
+
+					scmi_reg18: reg18@1 {
+						voltd-name = "reg18";
+						reg = <1>;
+						regulator-name = "reg18";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					scmi_usb33: usb33@2 {
+						reg = <2>;
+						regulator-name = "usb33";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+				};
+			};
+		};
+	};
+
+	soc {
+		scmi_sram: sram@2ffff000 {
+			compatible = "mmio-sram";
+			reg = <0x2ffff000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x2ffff000 0x1000>;
+
+			scmi_shm: scmi-sram@0 {
+				compatible = "arm,scmi-shmem";
+				reg = <0 0x80>;
+			};
+		};
+	};
+};
+
+&reg11 {
+	status = "disabled";
+};
+
+&reg18 {
+	status = "disabled";
+};
+
+&usb33 {
+	status = "disabled";
+};
+
+&usbotg_hs {
+	usb33d-supply = <&scmi_usb33>;
+};
+
+&usbphyc {
+	vdda1v1-supply = <&scmi_reg11>;
+	vdda1v8-supply = <&scmi_reg18>;
+};
+
+/delete-node/ &clk_hse;
+/delete-node/ &clk_hsi;
+/delete-node/ &clk_lse;
+/delete-node/ &clk_lsi;
+/delete-node/ &clk_csi;
diff --git a/arch/arm/boot/dts/st/stm32mp151.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi
new file mode 100644
index 000000000000..61508917521c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151.dtsi
@@ -0,0 +1,1846 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset/stm32mp1-resets.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			clock-frequency = <650000000>;
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>;
+		interrupt-parent = <&intc>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	intc: interrupt-controller@a0021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0xa0021000 0x1000>,
+		      <0xa0022000 0x2000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&intc>;
+	};
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		clk_hsi: clk-hsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <64000000>;
+		};
+
+		clk_lse: clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk_lsi: clk-lsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+		};
+
+		clk_csi: clk-csi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <4000000>;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&dts>;
+
+			trips {
+				cpu_alert1: cpu-alert1 {
+					temperature = <85000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu-crit {
+					temperature = <120000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+			};
+		};
+	};
+
+	booster: regulator-booster {
+		compatible = "st,stm32mp1-booster";
+		st,syscfg = <&syscfg>;
+		status = "disabled";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		timers2: timer@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM2_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 18 0x400 0x1>,
+			       <&dmamux1 19 0x400 0x1>,
+			       <&dmamux1 20 0x400 0x1>,
+			       <&dmamux1 21 0x400 0x1>,
+			       <&dmamux1 22 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers3: timer@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM3_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 23 0x400 0x1>,
+			       <&dmamux1 24 0x400 0x1>,
+			       <&dmamux1 25 0x400 0x1>,
+			       <&dmamux1 26 0x400 0x1>,
+			       <&dmamux1 27 0x400 0x1>,
+			       <&dmamux1 28 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers4: timer@40002000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM4_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 29 0x400 0x1>,
+			       <&dmamux1 30 0x400 0x1>,
+			       <&dmamux1 31 0x400 0x1>,
+			       <&dmamux1 32 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers5: timer@40003000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40003000 0x400>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM5_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 55 0x400 0x1>,
+			       <&dmamux1 56 0x400 0x1>,
+			       <&dmamux1 57 0x400 0x1>,
+			       <&dmamux1 58 0x400 0x1>,
+			       <&dmamux1 59 0x400 0x1>,
+			       <&dmamux1 60 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers6: timer@40004000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40004000 0x400>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM6_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 69 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timer@40005000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40005000 0x400>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM7_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 70 0x400 0x1>;
+			dma-names = "up";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		timers12: timer@40006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40006000 0x400>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM12_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timer@40007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40007000 0x400>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM13_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@12 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <12>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timer@40008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40008000 0x400>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM14_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@13 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <13>;
+				status = "disabled";
+			};
+		};
+
+		lptimer1: timer@40009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x40009000 0x400>;
+			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM1_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@0 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		spi2: spi@4000b000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI2_K>;
+			resets = <&rcc SPI2_R>;
+			dmas = <&dmamux1 39 0x400 0x05>,
+			       <&dmamux1 40 0x400 0x05>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s2: audio-controller@4000b000 {
+			compatible = "st,stm32h7-i2s";
+			#sound-dai-cells = <0>;
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi3: spi@4000c000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI3_K>;
+			resets = <&rcc SPI3_R>;
+			dmas = <&dmamux1 61 0x400 0x05>,
+			       <&dmamux1 62 0x400 0x05>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s3: audio-controller@4000c000 {
+			compatible = "st,stm32h7-i2s";
+			#sound-dai-cells = <0>;
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spdifrx: audio-controller@4000d000 {
+			compatible = "st,stm32h7-spdifrx";
+			#sound-dai-cells = <0>;
+			reg = <0x4000d000 0x400>;
+			clocks = <&rcc SPDIF_K>;
+			clock-names = "kclk";
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 93 0x400 0x01>,
+			       <&dmamux1 94 0x400 0x01>;
+			dma-names = "rx", "rx-ctrl";
+			status = "disabled";
+		};
+
+		usart2: serial@4000e000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000e000 0x400>;
+			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART2_K>;
+			wakeup-source;
+			dmas = <&dmamux1 43 0x400 0x15>,
+			       <&dmamux1 44 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		usart3: serial@4000f000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000f000 0x400>;
+			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART3_K>;
+			wakeup-source;
+			dmas = <&dmamux1 45 0x400 0x15>,
+			       <&dmamux1 46 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart4: serial@40010000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40010000 0x400>;
+			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART4_K>;
+			wakeup-source;
+			dmas = <&dmamux1 63 0x400 0x15>,
+			       <&dmamux1 64 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart5: serial@40011000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART5_K>;
+			wakeup-source;
+			dmas = <&dmamux1 65 0x400 0x15>,
+			       <&dmamux1 66 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c1: i2c@40012000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x40012000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C1_K>;
+			resets = <&rcc I2C1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x1>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40013000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x40013000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C2_K>;
+			resets = <&rcc I2C2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x2>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c3: i2c@40014000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x40014000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C3_K>;
+			resets = <&rcc I2C3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x4>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c5: i2c@40015000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x40015000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C5_K>;
+			resets = <&rcc I2C5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x10>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		cec: cec@40016000 {
+			compatible = "st,stm32-cec";
+			reg = <0x40016000 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CEC_K>, <&rcc CEC>;
+			clock-names = "cec", "hdmi-cec";
+			status = "disabled";
+		};
+
+		dac: dac@40017000 {
+			compatible = "st,stm32h7-dac-core";
+			reg = <0x40017000 0x400>;
+			clocks = <&rcc DAC12>;
+			clock-names = "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dac1: dac@1 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <1>;
+				status = "disabled";
+			};
+
+			dac2: dac@2 {
+				compatible = "st,stm32-dac";
+				#io-channel-cells = <1>;
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		uart7: serial@40018000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40018000 0x400>;
+			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART7_K>;
+			wakeup-source;
+			dmas = <&dmamux1 79 0x400 0x15>,
+			       <&dmamux1 80 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		uart8: serial@40019000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40019000 0x400>;
+			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART8_K>;
+			wakeup-source;
+			dmas = <&dmamux1 81 0x400 0x15>,
+			       <&dmamux1 82 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		timers1: timer@44000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44000000 0x400>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM1_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 11 0x400 0x1>,
+			       <&dmamux1 12 0x400 0x1>,
+			       <&dmamux1 13 0x400 0x1>,
+			       <&dmamux1 14 0x400 0x1>,
+			       <&dmamux1 15 0x400 0x1>,
+			       <&dmamux1 16 0x400 0x1>,
+			       <&dmamux1 17 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		timers8: timer@44001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44001000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
+			clocks = <&rcc TIM8_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 47 0x400 0x1>,
+			       <&dmamux1 48 0x400 0x1>,
+			       <&dmamux1 49 0x400 0x1>,
+			       <&dmamux1 50 0x400 0x1>,
+			       <&dmamux1 51 0x400 0x1>,
+			       <&dmamux1 52 0x400 0x1>,
+			       <&dmamux1 53 0x400 0x1>;
+			dma-names = "ch1", "ch2", "ch3", "ch4",
+				    "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-timer-counter";
+				status = "disabled";
+			};
+		};
+
+		usart6: serial@44003000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x44003000 0x400>;
+			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART6_K>;
+			wakeup-source;
+			dmas = <&dmamux1 71 0x400 0x15>,
+			       <&dmamux1 72 0x400 0x11>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi1: spi@44004000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI1_K>;
+			resets = <&rcc SPI1_R>;
+			dmas = <&dmamux1 37 0x400 0x05>,
+			       <&dmamux1 38 0x400 0x05>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2s1: audio-controller@44004000 {
+			compatible = "st,stm32h7-i2s";
+			#sound-dai-cells = <0>;
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi4: spi@44005000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x44005000 0x400>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI4_K>;
+			resets = <&rcc SPI4_R>;
+			dmas = <&dmamux1 83 0x400 0x05>,
+			       <&dmamux1 84 0x400 0x05>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		timers15: timer@44006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44006000 0x400>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM15_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 105 0x400 0x1>,
+			       <&dmamux1 106 0x400 0x1>,
+			       <&dmamux1 107 0x400 0x1>,
+			       <&dmamux1 108 0x400 0x1>;
+			dma-names = "ch1", "up", "trig", "com";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@14 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <14>;
+				status = "disabled";
+			};
+		};
+
+		timers16: timer@44007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44007000 0x400>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM16_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 109 0x400 0x1>,
+			       <&dmamux1 110 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+			timer@15 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <15>;
+				status = "disabled";
+			};
+		};
+
+		timers17: timer@44008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44008000 0x400>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
+			clocks = <&rcc TIM17_K>;
+			clock-names = "int";
+			dmas = <&dmamux1 111 0x400 0x1>,
+			       <&dmamux1 112 0x400 0x1>;
+			dma-names = "ch1", "up";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			timer@16 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <16>;
+				status = "disabled";
+			};
+		};
+
+		spi5: spi@44009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x44009000 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI5_K>;
+			resets = <&rcc SPI5_R>;
+			dmas = <&dmamux1 85 0x400 0x05>,
+			       <&dmamux1 86 0x400 0x05>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		sai1: sai@4400a000 {
+			compatible = "st,stm32h7-sai";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4400a000 0x400>;
+			reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI1_R>;
+			status = "disabled";
+
+			sai1a: audio-controller@4400a004 {
+				#sound-dai-cells = <0>;
+
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 87 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai1b: audio-controller@4400a024 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				clocks = <&rcc SAI1_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 88 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		sai2: sai@4400b000 {
+			compatible = "st,stm32h7-sai";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4400b000 0x400>;
+			reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI2_R>;
+			status = "disabled";
+
+			sai2a: audio-controller@4400b004 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x4 0x20>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 89 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai2b: audio-controller@4400b024 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				clocks = <&rcc SAI2_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 90 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		sai3: sai@4400c000 {
+			compatible = "st,stm32h7-sai";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4400c000 0x400>;
+			reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI3_R>;
+			status = "disabled";
+
+			sai3a: audio-controller@4400c004 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x04 0x20>;
+				clocks = <&rcc SAI3_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 113 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai3b: audio-controller@4400c024 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				clocks = <&rcc SAI3_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 114 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		dfsdm: dfsdm@4400d000 {
+			compatible = "st,stm32mp1-dfsdm";
+			reg = <0x4400d000 0x800>;
+			clocks = <&rcc DFSDM_K>;
+			clock-names = "dfsdm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dfsdm0: filter@0 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <0>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 101 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm1: filter@1 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <1>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 102 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm2: filter@2 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <2>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 103 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm3: filter@3 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <3>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 104 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm4: filter@4 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <4>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 91 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			dfsdm5: filter@5 {
+				compatible = "st,stm32-dfsdm-adc";
+				#io-channel-cells = <1>;
+				reg = <5>;
+				interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 92 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+		};
+
+		dma1: dma-controller@48000000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48000000 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA1>;
+			resets = <&rcc DMA1_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dma2: dma-controller@48001000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48001000 0x400>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA2>;
+			resets = <&rcc DMA2_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dmamux1: dma-router@48002000 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x48002000 0x40>;
+			#dma-cells = <3>;
+			dma-requests = <128>;
+			dma-masters = <&dma1 &dma2>;
+			dma-channels = <16>;
+			clocks = <&rcc DMAMUX>;
+			resets = <&rcc DMAMUX_R>;
+		};
+
+		adc: adc@48003000 {
+			compatible = "st,stm32mp1-adc-core";
+			reg = <0x48003000 0x400>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc ADC12>, <&rcc ADC12_K>;
+			clock-names = "bus", "adc";
+			interrupt-controller;
+			st,syscfg = <&syscfg>;
+			#interrupt-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			adc1: adc@0 {
+				compatible = "st,stm32mp1-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>;
+				interrupt-parent = <&adc>;
+				interrupts = <0>;
+				dmas = <&dmamux1 9 0x400 0x01>;
+				dma-names = "rx";
+				status = "disabled";
+			};
+
+			adc2: adc@100 {
+				compatible = "st,stm32mp1-adc";
+				#io-channel-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x100>;
+				interrupt-parent = <&adc>;
+				interrupts = <1>;
+				dmas = <&dmamux1 10 0x400 0x01>;
+				dma-names = "rx";
+				nvmem-cells = <&vrefint>;
+				nvmem-cell-names = "vrefint";
+				status = "disabled";
+				channel@13 {
+					reg = <13>;
+					label = "vrefint";
+				};
+				channel@14 {
+					reg = <14>;
+					label = "vddcore";
+				};
+			};
+		};
+
+		sdmmc3: mmc@48004000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x48004000 0x400>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC3_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC3_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		usbotg_hs: usb-otg@49000000 {
+			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+			reg = <0x49000000 0x10000>;
+			clocks = <&rcc USBO_K>, <&usbphyc>;
+			clock-names = "otg", "utmi";
+			resets = <&rcc USBO_R>;
+			reset-names = "dwc2";
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			g-rx-fifo-size = <512>;
+			g-np-tx-fifo-size = <32>;
+			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+			dr_mode = "otg";
+			otg-rev = <0x200>;
+			usb33d-supply = <&usb33>;
+			status = "disabled";
+		};
+
+		ipcc: mailbox@4c001000 {
+			compatible = "st,stm32mp1-ipcc";
+			#mbox-cells = <1>;
+			reg = <0x4c001000 0x400>;
+			st,proc-id = <0>;
+			interrupts-extended =
+				<&exti 61 1>,
+				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
+			clocks = <&rcc IPCC>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		dcmi: dcmi@4c006000 {
+			compatible = "st,stm32-dcmi";
+			reg = <0x4c006000 0x400>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc CAMITF_R>;
+			clocks = <&rcc DCMI>;
+			clock-names = "mclk";
+			dmas = <&dmamux1 75 0x400 0x01>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp1-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		pwr_regulators: pwr@50001000 {
+			compatible = "st,stm32mp1,pwr-reg";
+			reg = <0x50001000 0x10>;
+
+			reg11: reg11 {
+				regulator-name = "reg11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			reg18: reg18 {
+				regulator-name = "reg18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			usb33: usb33 {
+				regulator-name = "usb33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+
+		pwr_mcu: pwr_mcu@50001014 {
+			compatible = "st,stm32mp151-pwr-mcu", "syscon";
+			reg = <0x50001014 0x4>;
+		};
+
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp1-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
+
+		syscfg: syscon@50020000 {
+			compatible = "st,stm32mp157-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+			clocks = <&rcc SYSCFG>;
+		};
+
+		lptimer2: timer@50021000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50021000 0x400>;
+			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM2_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@1 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		lptimer3: timer@50022000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50022000 0x400>;
+			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM3_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@2 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		lptimer4: timer@50023000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50023000 0x400>;
+			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM4_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		lptimer5: timer@50024000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50024000 0x400>;
+			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LPTIM5_K>;
+			clock-names = "mux";
+			wakeup-source;
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		vrefbuf: vrefbuf@50025000 {
+			compatible = "st,stm32-vrefbuf";
+			reg = <0x50025000 0x8>;
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <2500000>;
+			clocks = <&rcc VREF>;
+			status = "disabled";
+		};
+
+		sai4: sai@50027000 {
+			compatible = "st,stm32h7-sai";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x50027000 0x400>;
+			reg = <0x50027000 0x4>, <0x500273f0 0x10>;
+			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&rcc SAI4_R>;
+			status = "disabled";
+
+			sai4a: audio-controller@50027004 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-a";
+				reg = <0x04 0x20>;
+				clocks = <&rcc SAI4_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 99 0x400 0x01>;
+				status = "disabled";
+			};
+
+			sai4b: audio-controller@50027024 {
+				#sound-dai-cells = <0>;
+				compatible = "st,stm32-sai-sub-b";
+				reg = <0x24 0x20>;
+				clocks = <&rcc SAI4_K>;
+				clock-names = "sai_ck";
+				dmas = <&dmamux1 100 0x400 0x01>;
+				status = "disabled";
+			};
+		};
+
+		dts: thermal@50028000 {
+			compatible = "st,stm32-thermal";
+			reg = <0x50028000 0x100>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc TMPSENS>;
+			clock-names = "pclk";
+			#thermal-sensor-cells = <0>;
+			status = "disabled";
+		};
+
+		hash1: hash@54002000 {
+			compatible = "st,stm32f756-hash";
+			reg = <0x54002000 0x400>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc HASH1>;
+			resets = <&rcc HASH1_R>;
+			dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
+			dma-names = "in";
+			dma-maxburst = <2>;
+			status = "disabled";
+		};
+
+		rng1: rng@54003000 {
+			compatible = "st,stm32-rng";
+			reg = <0x54003000 0x400>;
+			clocks = <&rcc RNG1_K>;
+			resets = <&rcc RNG1_R>;
+			status = "disabled";
+		};
+
+		mdma1: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			resets = <&rcc MDMA_R>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
+		};
+
+		fmc: memory-controller@58002000 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp1-fmc2-ebi";
+			reg = <0x58002000 0x1000>;
+			clocks = <&rcc FMC_K>;
+			resets = <&rcc FMC_R>;
+			status = "disabled";
+
+			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+				 <4 0 0x80000000 0x10000000>; /* NAND */
+
+			nand-controller@4,0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32mp1-fmc2-nfc";
+				reg = <4 0x00000000 0x1000>,
+				      <4 0x08010000 0x1000>,
+				      <4 0x08020000 0x1000>,
+				      <4 0x01000000 0x1000>,
+				      <4 0x09010000 0x1000>,
+				      <4 0x09020000 0x1000>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+				       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+				       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+				dma-names = "tx", "rx", "ecc";
+				status = "disabled";
+			};
+		};
+
+		qspi: spi@58003000 {
+			compatible = "st,stm32f469-qspi";
+			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+			reg-names = "qspi", "qspi_mm";
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
+			       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
+			dma-names = "tx", "rx";
+			clocks = <&rcc QSPI_K>;
+			resets = <&rcc QSPI_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58005000 0x1000>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC1_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58007000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		crc1: crc@58009000 {
+			compatible = "st,stm32f7-crc";
+			reg = <0x58009000 0x400>;
+			clocks = <&rcc CRC1>;
+			status = "disabled";
+		};
+
+		ethernet0: ethernet@5800a000 {
+			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
+			reg = <0x5800a000 0x2000>;
+			reg-names = "stmmaceth";
+			interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clock-names = "stmmaceth",
+				      "mac-clk-tx",
+				      "mac-clk-rx",
+				      "eth-ck",
+				      "ptp_ref",
+				      "ethstp";
+			clocks = <&rcc ETHMAC>,
+				 <&rcc ETHTX>,
+				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
+				 <&rcc ETHPTP_K>,
+				 <&rcc ETHSTP>;
+			st,syscon = <&syscfg 0x4>;
+			snps,mixed-burst;
+			snps,pbl = <2>;
+			snps,en-tx-lpi-clockgating;
+			snps,axi-config = <&stmmac_axi_config_0>;
+			snps,tso;
+			status = "disabled";
+
+			stmmac_axi_config_0: stmmac-axi-config {
+				snps,wr_osr_lmt = <0x7>;
+				snps,rd_osr_lmt = <0x7>;
+				snps,blen = <0 0 0 0 16 8 4>;
+			};
+		};
+
+		usbh_ohci: usb@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		usbh_ehci: usb@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
+			status = "disabled";
+		};
+
+		ltdc: display-controller@5a001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x5a001000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LTDC_PX>;
+			clock-names = "lcd";
+			resets = <&rcc LTDC_R>;
+			status = "disabled";
+		};
+
+		iwdg2: watchdog@5a002000 {
+			compatible = "st,stm32mp1-iwdg";
+			reg = <0x5a002000 0x400>;
+			clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
+			clock-names = "pclk", "lsi";
+			status = "disabled";
+		};
+
+		usbphyc: usbphyc@5a006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
+			status = "disabled";
+
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
+				reg = <0>;
+			};
+
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
+			};
+		};
+
+		usart1: serial@5c000000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x5c000000 0x400>;
+			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART1_K>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		spi6: spi@5c001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32h7-spi";
+			reg = <0x5c001000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI6_K>;
+			resets = <&rcc SPI6_R>;
+			dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
+			       <&mdma1 35 0x0 0x40002 0x0 0x0>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c4: i2c@5c002000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x5c002000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C4_K>;
+			resets = <&rcc I2C4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x8>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			clocks = <&rcc RTCAPB>, <&rcc RTC>;
+			clock-names = "pclk", "rtc_ck";
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		bsec: efuse@5c005000 {
+			compatible = "st,stm32mp15-bsec";
+			reg = <0x5c005000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			part_number_otp: part-number-otp@4 {
+				reg = <0x4 0x1>;
+			};
+			vrefint: vrefin-cal@52 {
+				reg = <0x52 0x2>;
+			};
+			ts_cal1: calib@5c {
+				reg = <0x5c 0x2>;
+			};
+			ts_cal2: calib@5e {
+				reg = <0x5e 0x2>;
+			};
+		};
+
+		i2c6: i2c@5c009000 {
+			compatible = "st,stm32mp15-i2c";
+			reg = <0x5c009000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C6_K>;
+			resets = <&rcc I2C6_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			st,syscfg-fmp = <&syscfg 0x4 0x20>;
+			wakeup-source;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		tamp: tamp@5c00a000 {
+			compatible = "st,stm32-tamp", "syscon", "simple-mfd";
+			reg = <0x5c00a000 0x400>;
+		};
+
+		/*
+		 * Break node order to solve dependency probe issue between
+		 * pinctrl and exti.
+		 */
+		pinctrl: pinctrl@50002000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-pinctrl";
+			ranges = <0 0x50002000 0xa400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioa: gpio@50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA>;
+				st,bank-name = "GPIOA";
+				status = "disabled";
+			};
+
+			gpiob: gpio@50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOB>;
+				st,bank-name = "GPIOB";
+				status = "disabled";
+			};
+
+			gpioc: gpio@50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOC>;
+				st,bank-name = "GPIOC";
+				status = "disabled";
+			};
+
+			gpiod: gpio@50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&rcc GPIOD>;
+				st,bank-name = "GPIOD";
+				status = "disabled";
+			};
+
+			gpioe: gpio@50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&rcc GPIOE>;
+				st,bank-name = "GPIOE";
+				status = "disabled";
+			};
+
+			gpiof: gpio@50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&rcc GPIOF>;
+				st,bank-name = "GPIOF";
+				status = "disabled";
+			};
+
+			gpiog: gpio@50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&rcc GPIOG>;
+				st,bank-name = "GPIOG";
+				status = "disabled";
+			};
+
+			gpioh: gpio@50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&rcc GPIOH>;
+				st,bank-name = "GPIOH";
+				status = "disabled";
+			};
+
+			gpioi: gpio@5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&rcc GPIOI>;
+				st,bank-name = "GPIOI";
+				status = "disabled";
+			};
+
+			gpioj: gpio@5000b000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x9000 0x400>;
+				clocks = <&rcc GPIOJ>;
+				st,bank-name = "GPIOJ";
+				status = "disabled";
+			};
+
+			gpiok: gpio@5000c000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xa000 0x400>;
+				clocks = <&rcc GPIOK>;
+				st,bank-name = "GPIOK";
+				status = "disabled";
+			};
+		};
+
+		pinctrl_z: pinctrl@54004000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-z-pinctrl";
+			ranges = <0 0x54004000 0x400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioz: gpio@54004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x400>;
+				clocks = <&rcc GPIOZ>;
+				st,bank-name = "GPIOZ";
+				st,bank-ioport = <11>;
+				status = "disabled";
+			};
+		};
+	};
+
+	mlahb: ahb {
+		compatible = "st,mlahb", "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		dma-ranges = <0x00000000 0x38000000 0x10000>,
+			     <0x10000000 0x10000000 0x60000>,
+			     <0x30000000 0x30000000 0x60000>;
+
+		m4_rproc: m4@10000000 {
+			compatible = "st,stm32mp1-m4";
+			reg = <0x10000000 0x40000>,
+			      <0x30000000 0x40000>,
+			      <0x38000000 0x10000>;
+			resets = <&rcc MCU_R>;
+			reset-names = "mcu_rst";
+			st,syscfg-holdboot = <&rcc 0x10C 0x1>;
+			st,syscfg-pdds = <&pwr_mcu 0x0 0x1>;
+			st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
+			st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts b/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts
new file mode 100644
index 000000000000..e0f828ecc2fa
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-dhcor-testbench.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-testbench.dtsi"
+
+/ {
+	model = "DH electronics STM32MP151A DHCOR Testbench";
+	compatible = "dh,stm32mp151a-dhcor-testbench",
+		     "dh,stm32mp151a-dhcor-som",
+		     "st,stm32mp151";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts
new file mode 100644
index 000000000000..75874eafde11
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1a.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1A";
+	compatible = "prt,prtt1a", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
+
+&pwm5_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+	};
+};
+
+&pwm5_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts
new file mode 100644
index 000000000000..7ecf31263abc
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1c.dts
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1C";
+	compatible = "prt,prtt1c", "st,stm32mp151";
+
+	clock_ksz9031: clock-ksz9031 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_sja1105: clock-sja1105 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethernet0 {
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpioa {
+	gpio-line-names =
+		"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
+		"", "", "", "", "", "", "", "SPI1_nSS";
+};
+
+&gpiod {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"WFM_RESET", "", "", "", "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names =
+		"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
+		"", "", "", "", "WFM_nIRQ", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "PHY3_nINT",
+		"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
+		"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
+};
+
+&mdio0 {
+	/* All this DP83TD510E PHYs can't be probed before switch@0 is
+	 * probed so we need to use compatible with PHYid
+	 */
+	/* TI DP83TD510E */
+	t1l0_phy: ethernet-phy@6 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <6>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l1_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <7>;
+		interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l2_phy: ethernet-phy@10 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <10>;
+		interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* Micrel KSZ9031 */
+	rj45_phy: ethernet-phy@2 {
+		reg = <2>;
+		interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <1000>;
+
+		clocks = <&clock_ksz9031>;
+	};
+};
+
+&qspi {
+	status = "disabled";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc2_b4_od_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+	};
+};
+
+&sdmmc2_b4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_b4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+			 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc2_d47_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	non-removable;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mmc@1 {
+		compatible = "prt,prtt1c-wfm200", "silabs,wf200";
+		reg = <1>;
+	};
+};
+
+&sdmmc3_b4_od_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+	};
+};
+
+&sdmmc3_b4_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+	};
+};
+
+&sdmmc3_b4_sleep_pins_b {
+	pins {
+		pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+			 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pins_b>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	switch@0 {
+		compatible = "nxp,sja1105q";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-rx-delay-us = <1>;
+		spi-tx-delay-us = <1>;
+		spi-cpha;
+
+		reset-gpios = <&gpioe 6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clock_sja1105>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "t1l0";
+				phy-mode = "rmii";
+				phy-handle = <&t1l0_phy>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "t1l1";
+				phy-mode = "rmii";
+				phy-handle = <&t1l1_phy>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "t1l2";
+				phy-mode = "rmii";
+				phy-handle = <&t1l2_phy>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "rj45";
+				phy-handle = <&rj45_phy>;
+				phy-mode = "rgmii-id";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "cpu";
+				ethernet = <&ethernet0>;
+				phy-mode = "rmii";
+
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi b/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi
new file mode 100644
index 000000000000..dd23de85100c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1l.dtsi
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxad-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mdio-gpio0 = &mdio0;
+		serial0 = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+	 * stmmac MDC clock without reducing system bus rate, we need to use
+	 * gpio based MDIO bus.
+	 */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>; /* ETH1_RMII_TX_EN */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK input */
+			 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&ethernet0_rmii_sleep_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&iwdg2 {
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&qspi_bk1_pins_a {
+	pins1 {
+		bias-pull-up;
+		drive-push-pull;
+		slew-rate = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_od_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc1_b4_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart4_idle_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* UART4_TX */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+		bias-disable;
+		drive-push-pull;
+		slew-rate = <0>;
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>, /* UART4_TX */
+			<STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+	};
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&reg_3v3>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&reg_3v3>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts b/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts
new file mode 100644
index 000000000000..ad25929e64e6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp151a-prtt1s.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1S";
+	compatible = "prt,prtt1s", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <100000>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	humidity-sensor@40 {
+		compatible = "ti,hdc1080";
+		reg = <0x40>;
+	};
+
+	co2-sensor@62 {
+		compatible = "sensirion,scd41";
+		reg = <0x62>;
+	};
+};
+
+&i2c1_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+	};
+};
+
+&i2c1_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+	};
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi
new file mode 100644
index 000000000000..486084e0b80b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp151.dtsi"
+
+/ {
+	cpus {
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			clock-frequency = <650000000>;
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	arm-pmu {
+		interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+
+	timer {
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc {
+		m_can1: can@4400e000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+
+		m_can2: can@4400f000 {
+			compatible = "bosch,m_can";
+			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+			clock-names = "hclk", "cclk";
+			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts b/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts
new file mode 100644
index 000000000000..b4e504f026ce
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-dhcom-drc02.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP153C-C065-R102-F0819-SPI-E2-CAN2-RTC-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * DRC02 PCB number: 568-100 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-drc02.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOM DRC02";
+	compatible = "dh,stm32mp153c-dhcom-drc02", "dh,stm32mp153c-dhcom-som",
+		     "st,stm32mp153";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts
new file mode 100644
index 000000000000..c8b9818499ea
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp153c-dhcor-drc-compact.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * DRC Compact PCB number: 627-100 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOR DRC Compact";
+	compatible = "dh,stm32mp153c-dhcor-drc-compact",
+		     "dh,stm32mp153c-dhcor-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_c>;
+	pinctrl-1 = <&m_can1_sleep_pins_c>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157.dtsi b/arch/arm/boot/dts/st/stm32mp157.dtsi
new file mode 100644
index 000000000000..5e733cd16ff9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include "stm32mp153.dtsi"
+
+/ {
+	soc {
+		gpu: gpu@59000000 {
+			compatible = "vivante,gc";
+			reg = <0x59000000 0x800>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc GPU>, <&rcc GPU_K>;
+			clock-names = "bus" ,"core";
+			resets = <&rcc GPU_R>;
+		};
+
+		dsi: dsi@5a000000 {
+			compatible = "st,stm32-dsi";
+			reg = <0x5a000000 0x800>;
+			clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
+			clock-names = "pclk", "ref", "px_clk";
+			resets = <&rcc DSI_R>;
+			reset-names = "apb";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts
new file mode 100644
index 000000000000..8a6eaca994d1
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-avenger96.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+/* This DT is here only for backward compatibility */
+#include "stm32mp157a-dhcor-avenger96.dts"
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts b/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts
new file mode 100644
index 000000000000..275167f26fd9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dhcor-avenger96.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP157A-C065-R102-V18-SPI-C-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * Avenger96 PCB number: 588-200 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-avenger96.dtsi"
+
+/ {
+	model = "Arrow Electronics STM32MP157A Avenger96 board";
+	compatible = "arrow,stm32mp157a-avenger96", "dh,stm32mp157a-dhcor-som",
+		     "st,stm32mp157";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_b>;
+	pinctrl-1 = <&m_can1_sleep_pins_b>;
+	status = "disabled";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts
new file mode 100644
index 000000000000..afcd6285890c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dk1-scmi.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157a-dk1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 SCMI Discovery Board";
+	compatible = "st,stm32mp157a-dk1-scmi", "st,stm32mp157a-dk1", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names =  "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-dk1.dts b/arch/arm/boot/dts/st/stm32mp157a-dk1.dts
new file mode 100644
index 000000000000..0da3667ab1e0
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-dk1.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp15xx-dkx.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
+	compatible = "st,stm32mp157a-dk1", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
new file mode 100644
index 000000000000..4279b26547df
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0 10.1\" Open Frame";
+	compatible = "engicam,icore-stm32mp1-ctouch2-of10",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	panel {
+		compatible = "ampire,am-1280800n3tzqw-t00h";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_in_lvds: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+	phy-dsi-supply = <&reg18>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&bridge_in>;
+			};
+		};
+	};
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in_lvds>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts
new file mode 100644
index 000000000000..60ce4425a7fd
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-ctouch2.dts
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0";
+	compatible = "engicam,icore-stm32mp1-ctouch2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts
new file mode 100644
index 000000000000..efba54289820
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1-edimm2.2.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit";
+	compatible = "engicam,icore-stm32mp1-edimm2.2",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	panel {
+		compatible = "yes-optoelectronics,ytc700tlag-05-201c";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_out_bridge: endpoint {
+				remote-endpoint = <&bridge_out_panel>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+	phy-dsi-supply = <&reg18>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in_ltdc: endpoint {
+				remote-endpoint = <&ltdc_out_dsi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out_bridge: endpoint {
+				remote-endpoint = <&bridge_in_dsi>;
+			};
+		};
+	};
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out_panel: endpoint {
+					remote-endpoint = <&panel_out_bridge>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint {
+			remote-endpoint = <&dsi_in_ltdc>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi
new file mode 100644
index 000000000000..9de893101b40
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-icore-stm32mp1.dtsi
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/ {
+	compatible = "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_usb: regulator-vdd-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_usb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdda: regulator-vdda {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd_ddr: regulator-vdd-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+	};
+
+	vtt_ddr: regulator-vtt-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_ddr";
+		regulator-min-microvolt = <675000>;
+		regulator-max-microvolt = <675000>;
+		regulator-always-on;
+		vin-supply = <&vdd>;
+	};
+
+	vref_ddr: regulator-vref-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vref_ddr";
+		regulator-min-microvolt = <675000>;
+		regulator-max-microvolt = <675000>;
+		regulator-always-on;
+		vin-supply = <&vdd>;
+	};
+
+	vdd_sd: regulator-vdd-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v3v3: regulator-v3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	v2v8: regulator-v2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "v2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+
+	v1v8: regulator-v1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "v1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2{
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc{
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc{
+	status = "okay";
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts b/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts
new file mode 100644
index 000000000000..6a5a4af25bd9
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-iot-box.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+#include "stm32mp157a-stinger96.dtsi"
+
+/ {
+	model = "Shiratech STM32MP157A IoT Box";
+	compatible = "shiratech,stm32mp157a-iot-box", "st,stm32mp157";
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&i2c2 {
+	ccs811@5b {
+		compatible = "ams,ccs811";
+		reg = <0x5b>;
+		wakeup-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpioa 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* WiFi */
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <1>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* Bluetooth */
+&uart4 {
+	/* Note: HW flow control is broken, hence using custom CTS/RTS gpios */
+	/delete-property/st,hw-flow-ctrl;
+	cts-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpiob 0 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	bluetooth {
+		shutdown-gpios = <&gpiog 2 GPIO_ACTIVE_HIGH>;
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <115200>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
new file mode 100644
index 000000000000..5116a7785201
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
@@ -0,0 +1,157 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-microgea-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 7\" Open Frame";
+	compatible = "engicam,microgea-stm32mp1-microdev2.0-of7",
+		     "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiof 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		power-supply = <&panel_pwr>;
+	};
+
+	panel_pwr: regulator-panel-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiob 10 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+
+	panel {
+		compatible = "auo,b101aw03";
+		backlight = <&backlight>;
+		enable-gpios = <&gpiof 2 GPIO_ACTIVE_HIGH>;
+		power-supply = <&lcd_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	status = "okay";
+};
+
+&ltdc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ltdc_pins>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pinctrl {
+	ltdc_pins: ltdc-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 10, AF14)>,	/* LTDC_B2 */
+				 <STM32_PINMUX('H', 12, AF14)>,	/* LTDC_R6 */
+				 <STM32_PINMUX('H', 11, AF14)>,	/* LTDC_R5 */
+				 <STM32_PINMUX('D', 10, AF14)>,	/* LTDC_B3 */
+				 <STM32_PINMUX('D', 9, AF14)>,	/* LTDC_B0 */
+				 <STM32_PINMUX('E', 5, AF14)>,	/* LTDC_G0 */
+				 <STM32_PINMUX('E', 6, AF14)>,	/* LTDC_G1 */
+				 <STM32_PINMUX('E', 13, AF14)>,	/* LTDC_DE */
+				 <STM32_PINMUX('E', 15, AF14)>,	/* LTDC_R7 */
+				 <STM32_PINMUX('G', 7, AF14)>,	/* LTDC_CLK */
+				 <STM32_PINMUX('G', 12, AF14)>,	/* LTDC_B1 */
+				 <STM32_PINMUX('H', 2, AF14)>,	/* LTDC_R0 */
+				 <STM32_PINMUX('H', 3, AF14)>,	/* LTDC_R1 */
+				 <STM32_PINMUX('H', 8, AF14)>,	/* LTDC_R2 */
+				 <STM32_PINMUX('H', 9, AF14)>,	/* LTDC_R3 */
+				 <STM32_PINMUX('H', 10, AF14)>,	/* LTDC_R4 */
+				 <STM32_PINMUX('H', 13, AF14)>,	/* LTDC_G2 */
+				 <STM32_PINMUX('H', 14, AF14)>,	/* LTDC_G3 */
+				 <STM32_PINMUX('H', 15, AF14)>,	/* LTDC_G4 */
+				 <STM32_PINMUX('I', 0, AF14)>,	/* LTDC_G5 */
+				 <STM32_PINMUX('I', 1, AF14)>,	/* LTDC_G6 */
+				 <STM32_PINMUX('I', 2, AF14)>,	/* LTDC_G7 */
+				 <STM32_PINMUX('I', 4, AF14)>,	/* LTDC_B4 */
+				 <STM32_PINMUX('I', 5, AF14)>,	/* LTDC_B5 */
+				 <STM32_PINMUX('B', 8, AF14)>,	/* LTDC_B6 */
+				 <STM32_PINMUX('I', 7, AF14)>,	/* LTDC_B7 */
+				 <STM32_PINMUX('I', 9, AF14)>,	/* LTDC_VSYNC */
+				 <STM32_PINMUX('I', 10, AF14)>;	/* LTDC_HSYNC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <3>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* J31: RS323 */
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
new file mode 100644
index 000000000000..d949559be020
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-microgea-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 Carrier Board";
+	compatible = "engicam,microgea-stm32mp1-microdev2.0",
+		     "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* J31: RS323 */
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi
new file mode 100644
index 000000000000..fb4600a59869
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-microgea-stm32mp1.dtsi
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/ {
+	compatible = "engicam,microgea-stm32mp1", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x10000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	vin: regulator-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddcore: regulator-vddcore {
+		compatible = "regulator-fixed";
+		regulator-name = "vddcore";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+
+	vdd: regulator-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+
+	vddq_ddr: regulator-vddq-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vddq_ddr";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vin>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_a>;
+	pinctrl-1 = <&fmc_sleep_pins_a>;
+	status = "okay";
+
+	nand-controller@4,0 {
+		status = "okay";
+
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2{
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc{
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc{
+	status = "okay";
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts
new file mode 100644
index 000000000000..249a53877512
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+#include "stm32mp157a-stinger96.dtsi"
+
+/ {
+	model = "Shiratech STM32MP157A Stinger96 board";
+	compatible = "shiratech,stm32mp157a-stinger96", "st,stm32mp157";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157a-stinger96.dtsi b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dtsi
new file mode 100644
index 000000000000..5f85598cc7c6
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157a-stinger96.dtsi
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2020 Manivannan Sadhasivam
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		serial2 = &usart2;
+		spi0 = &spi4;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x10000000>;
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "green:user1";
+			gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user2";
+			gpios = <&gpioh 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user3";
+			gpios = <&gpioh 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user4";
+			gpios = <&gpiof 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioa 8 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+};
+
+/* Only headless mode is supported */
+&gpu {
+	status = "disabled";
+};
+
+/* LS-I2C0 */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <1000>;
+	i2c-scl-falling-time-ns = <300>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v9: ldo2 {
+				regulator-name = "v2v9";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	broken-cd;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+/* LS-SPI0 */
+&spi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi4_pins_a>;
+	cs-gpios = <&gpioe 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+/* BG96 */
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_b>;
+	pinctrl-1 = <&usart2_sleep_pins_b>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* LS-UART0 */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_c>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* Debug console */
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts
new file mode 100644
index 000000000000..6dd8216c235e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dhcom-pdk2.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP157C-C065-R102-F0819-SPI-E2-CAN2-SDR104-RTC-WBT-T-DSI-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-pdk2.dtsi"
+
+/ {
+	model = "DH electronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "dh,stm32mp157c-dhcom-som",
+		     "st,stm32mp157";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts b/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts
new file mode 100644
index 000000000000..7067a860aaff
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dhcom-picoitx.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM STM32MP1 variant:
+ * DHCM-STM32MP157C-C065-R102-F0819-SPI-E-CAN2-SD-RTC-T-DSI-I-01D2
+ * DHCOM PCB number: 587-200 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcom-som.dtsi"
+#include "stm32mp15xx-dhcom-picoitx.dtsi"
+
+/ {
+	model = "DH electronics STM32MP157C DHCOM PicoITX";
+	compatible = "dh,stm32mp157c-dhcom-picoitx", "dh,stm32mp157c-dhcom-som",
+		     "st,stm32mp157";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts
new file mode 100644
index 000000000000..39358d902000
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2-scmi.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-dk2.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-DK2 SCMI Discovery Board";
+	compatible = "st,stm32mp157c-dk2-scmi", "st,stm32mp157c-dk2", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names =  "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-dk2.dts b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
new file mode 100644
index 000000000000..4bef2300ed7c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-dk2.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp15xx-dkx.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-DK2 Discovery Board";
+	compatible = "st,stm32mp157c-dk2", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial3 = &usart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dsi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	phy-dsi-supply = <&reg18>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_ep1_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	panel@0 {
+		compatible = "orisetech,otm8009a";
+		reg = <0>;
+		reset-gpios = <&gpioe 4 GPIO_ACTIVE_LOW>;
+		power-supply = <&v3v3>;
+		status = "okay";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	touchscreen@38 {
+		compatible = "focaltech,ft6236";
+		reg = <0x38>;
+		interrupts = <2 2>;
+		interrupt-parent = <&gpiof>;
+		interrupt-controller;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		status = "okay";
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ltdc_ep1_out: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&usart2 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart2_pins_c>;
+	pinctrl-1 = <&usart2_sleep_pins_c>;
+	pinctrl-2 = <&usart2_idle_pins_c>;
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts
new file mode 100644
index 000000000000..07ea765a4553
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ed1-scmi.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-ED1 SCMI eval daughter";
+	compatible = "st,stm32mp157c-ed1-scmi", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names =  "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ed1.dts b/arch/arm/boot/dts/st/stm32mp157c-ed1.dts
new file mode 100644
index 000000000000..66ed5f9921ba
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ed1.dts
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	model = "STMicroelectronics STM32MP157C eval daughter";
+	compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpiof 14 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	/* ANA0, ANA1 are dedicated pins and don't need pinctrl: only in6. */
+	pinctrl-0 = <&adc1_in6_pins_a>;
+	pinctrl-names = "default";
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			/* 16.5 ck_cycles sampling time */
+			st,min-sample-time-ns = <400>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <400>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <400>;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbotg_hs {
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts b/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts
new file mode 100644
index 000000000000..33b3f11d24bb
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-emsbc-argon.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+/dts-v1/;
+
+#include "stm32mp157c-emstamp-argon.dtsi"
+
+/ {
+	model = "emtrion STM32MP157C emSBC-Argon Developer Board";
+	compatible = "emtrion,stm32mp157c-emsbc-argon", "emtrion,stm32mp157c-emstamp-argon",
+			"st,stm32mp157";
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-2 {
+			label = "red";
+			gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+		led-3 {
+			label = "green";
+			gpios = <&gpioe 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+	};
+};
+
+&dac {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi b/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi
new file mode 100644
index 000000000000..94e38141af67
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-emstamp-argon.dtsi
@@ -0,0 +1,543 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &usart2;
+		serial2 = &usart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x2000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x2000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10044000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10044000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "panic";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+		led-1 {
+			label = "heartbeat";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+
+	adc1: adc@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&adc1_in6_pins_a>;
+		status = "disabled";
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		channel@12 {
+			reg = <12>;
+			label = "sense_temp";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@15 {
+			reg = <15>;
+			label = "vbat";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@16 {
+			reg = <16>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@17 {
+			reg = <17>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	snps,reset-gpio = <&gpioa 1 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 30000 50000>;
+	pinctrl-0 = <&ethernet0_rmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-always-on;
+			};
+
+			vdda: ldo6 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				regulator-boot-on;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge;
+			};
+
+			vbus_usbh: pwr_sw2 {
+				regulator-name = "usbh_vbus";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	interrupt-names = "wdg";
+	recovery;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	arm,primecell-periphid = <0x10153180>;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "disabled";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm1_pins_b>;
+		pinctrl-1 = <&pwm1_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_d>;
+	pinctrl-1 = <&usart3_sleep_pins_d>;
+	pinctrl-2 = <&usart3_idle_pins_d>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts b/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts
new file mode 100644
index 000000000000..813086ec2489
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ev1-scmi.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ev1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-EV1 SCMI eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1-scmi", "st,stm32mp157c-ev1", "st,stm32mp157c-ed1",
+		     "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&m_can1 {
+	clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&m4_rproc {
+	/delete-property/ st,syscfg-holdboot;
+	resets = <&scmi_reset RST_SCMI_MCU>,
+		 <&scmi_reset RST_SCMI_MCU_HOLD_BOOT>;
+	reset-names =  "mcu_rst", "hold_boot";
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-ev1.dts b/arch/arm/boot/dts/st/stm32mp157c-ev1.dts
new file mode 100644
index 000000000000..af3800501875
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-ev1.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+/ {
+	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	aliases {
+		serial1 = &usart3;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		clk_ext_camera: clk-ext-camera {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	joystick {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&joystick_pins>;
+		pinctrl-names = "default";
+		button-0 {
+			label = "JoySel";
+			linux,code = <KEY_ENTER>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		};
+		button-1 {
+			label = "JoyDown";
+			linux,code = <KEY_DOWN>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		};
+		button-2 {
+			label = "JoyLeft";
+			linux,code = <KEY_LEFT>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <2 IRQ_TYPE_EDGE_RISING>;
+		};
+		button-3 {
+			label = "JoyRight";
+			linux,code = <KEY_RIGHT>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		};
+		button-4 {
+			label = "JoyUp";
+			linux,code = <KEY_UP>;
+			interrupt-parent = <&stmfx_pinctrl>;
+			interrupts = <4 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	panel_backlight: panel-backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
+		default-on;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+
+	port {
+		dcmi_0: endpoint {
+			remote-endpoint = <&ov5640_0>;
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+			bus-width = <8>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+		};
+	};
+};
+
+&dsi {
+	phy-dsi-supply = <&reg18>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&dsi_panel_in>;
+			};
+		};
+	};
+
+	panel@0 {
+		compatible = "raydium,rm68200";
+		reg = <0>;
+		reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
+		backlight = <&panel_backlight>;
+		power-supply = <&v3v3>;
+		status = "okay";
+
+		port {
+			dsi_panel_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_a>;
+	pinctrl-1 = <&fmc_sleep_pins_a>;
+	status = "okay";
+
+	nand-controller@4,0 {
+		status = "okay";
+
+		nand@0 {
+			reg = <0>;
+			nand-on-flash-bbt;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		clocks = <&clk_ext_camera>;
+		clock-names = "xclk";
+		AVDD-supply = <&v2v8>;
+		DOVDD-supply = <&v2v8>;
+		DVDD-supply = <&v2v8>;
+		powerdown-gpios = <&stmfx_pinctrl 18 (GPIO_ACTIVE_HIGH | GPIO_PUSH_PULL)>;
+		reset-gpios = <&stmfx_pinctrl 19 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>;
+		rotation = <180>;
+		status = "okay";
+
+		port {
+			ov5640_0: endpoint {
+				remote-endpoint = <&dcmi_0>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+
+	stmfx: stmfx@42 {
+		compatible = "st,stmfx-0300";
+		reg = <0x42>;
+		interrupts = <8 IRQ_TYPE_EDGE_RISING>;
+		interrupt-parent = <&gpioi>;
+		vdd-supply = <&v3v3>;
+
+		stmfx_pinctrl: pinctrl {
+			compatible = "st,stmfx-0300-pinctrl";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&stmfx_pinctrl 0 0 24>;
+
+			joystick_pins: joystick-pins {
+				pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
+				bias-pull-down;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a
+		     &qspi_bk2_pins_a
+		     &qspi_cs2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a
+		     &qspi_bk2_sleep_pins_a
+		     &qspi_cs2_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: flash@1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-1 = <&pwm2_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-1 = <&pwm8_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_b>;
+	pinctrl-1 = <&usart3_sleep_pins_b>;
+	pinctrl-2 = <&usart3_idle_pins_b>;
+	/*
+	 * HW flow control USART3_RTS is optional, and isn't default wired to
+	 * the connector. SB23 needs to be soldered in order to use it, and R77
+	 * (ETH_CLK) should be removed.
+	 */
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3>;
+	};
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts
new file mode 100644
index 000000000000..eada9cf257be
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-lxa-mc1.dts
@@ -0,0 +1,253 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Linux Automation MC-1 board";
+	compatible = "lxa,stm32mp157c-mc1", "oct,stm32mp15xx-osd32", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 31 63 95 127 159 191 223 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_5v2>; /* 3V3_BACKLIGHT */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "mc1:green:act";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	led-controller-1 {
+		compatible = "pwm-leds";
+
+		/* led-1 to led-3 are part of a single RGB led */
+		led-1 {
+			label = "mc1:red:rgb";
+			pwms = <&leds_pwm 1 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+
+		led-2 {
+			label = "mc1:green:rgb";
+			pwms = <&leds_pwm 2 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+
+		led-3 {
+			label = "mc1:blue:rgb";
+			pwms = <&leds_pwm 3 1000000 0>;
+			max-brightness = <255>;
+			active-low;
+		};
+	};
+
+	panel: panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&backlight>;
+		enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&v3v3>;
+	};
+
+	/* supplied by either debug board or PoE */
+	reg_5v2: regulator_5v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V2";
+		regulator-min-microvolt = <5200000>;
+		regulator-max-microvolt = <5200000>;
+		regulator-always-on;
+	};
+};
+
+&ethernet0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 { /* KSZ9031RN */
+			reg = <3>;
+			reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			interrupt-parent = <&gpioa>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			micrel,force-master;
+		};
+	};
+};
+
+&gpioz {
+	gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "",
+			  "HWID4", "HWID5";
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_b>;
+	pinctrl-1 = <&i2c5_sleep_pins_b>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		interrupt-parent = <&gpiod>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */
+		vcc-supply = <&reg_3v3>;
+		reg = <0x38>;
+		reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */
+		touchscreen-size-x = <1792>;
+		touchscreen-size-y = <1024>;
+		wakeup-source;
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_c>;
+	pinctrl-1 = <&ltdc_sleep_pins_c>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
+
+&pmic {
+	regulators {
+		buck4-supply = <&reg_5v2>;	/* VIN */
+		ldo2-supply = <&reg_5v2>;	/* PMIC_LDO25IN */
+		ldo5-supply = <&reg_5v2>;	/* PMIC_LDO25IN */
+		boost-supply = <&reg_5v2>;	/* PMIC_BSTIN */
+		pwr_sw2-supply = <&bst_out>;    /* PMIC_SWIN */
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	bus-width = <4>;
+	cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-1-8-v;
+	st,neg-edge;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+	/*
+	 * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to
+	 * work, thus enable internal pull-ups.
+	 */
+	pins1 {
+		/delete-property/ bias-disable;
+		bias-pull-up;
+	};
+	pins2 {
+		/delete-property/ bias-disable;
+		bias-pull-up;
+	};
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+	bus-width = <8>;
+	mmc-ddr-3_3v;
+	no-1-8-v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&timers3 {
+	status = "okay";
+
+	backlight_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm3_pins_b>;
+		pinctrl-1 = <&pwm3_sleep_pins_b>;
+		status = "okay";
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	leds_pwm: pwm {
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm5_pins_b>;
+		pinctrl-1 = <&pwm5_sleep_pins_b>;
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi
new file mode 100644
index 000000000000..e22871dc580c
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-odyssey-som.dtsi
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C SOM";
+	compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_d>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_d>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts
new file mode 100644
index 000000000000..a8b3f7a54703
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-odyssey.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski@gmail.com>.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-odyssey-som.dtsi"
+
+/ {
+	model = "Seeed Studio Odyssey-STM32MP157C Board";
+	compatible = "seeed,stm32mp157c-odyssey",
+		     "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&dcmi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_b>;
+	pinctrl-1 = <&dcmi_sleep_pins_b>;
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	assigned-clocks = <&rcc ETHCK_K>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <125000000>; /* Clock PLL4 to 750Mhz in ATF/U-Boot */
+	st,eth-clk-sel;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@7 { /* KSZ9031RN */
+			reg = <7>;
+			reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts
new file mode 100644
index 000000000000..28d7203264ce
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp1-3.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard@linrt.com>.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include "stm32mp157c-phycore-stm32mp15-som.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-STM32MP1-3 Dev Board";
+	compatible = "phytec,phycore-stm32mp1-3",
+		     "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+	aliases {
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		mmc2 = &sdmmc3;
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &usart1;
+	};
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c4_eeprom {
+	status = "okay";
+};
+
+&i2c4_rtc {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+};
+
+&sdmmc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi
new file mode 100644
index 000000000000..4e8b2d2b30c7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp157c-phycore-stm32mp15-som.dtsi
@@ -0,0 +1,577 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022-2023 Steffen Trumtrar <kernel@pengutronix.de>
+ * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
+ * Author: Dom VOVARD <dom.vovard@linrt.com>.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "stm32mp15-pinctrl.dtsi"
+
+/ {
+	model = "PHYTEC phyCORE-STM32MP15 SOM";
+	compatible = "phytec,phycore-stm32mp157c-som", "st,stm32mp157";
+
+	aliases {
+		ethernet0 = &ethernet0;
+		rtc0 = &i2c4_rtc;
+		rtc1 = &rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-home {
+			label = "Home";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-enter {
+			label = "Enter";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP1-PHYCORE";
+		routing =
+			"Playback", "MCLK", /* Set a route between "MCLK" and "playback" widgets */
+			"Capture", "MCLK";
+		dais = <&sai2b_port>,
+		       <&sai2a_port>;
+	};
+
+	regulator_vin: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rgmii_pins_d>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_d>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+	st,eth-clk-sel;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			interrupt-parent = <&gpiog>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,min-output-impedance;
+			enet-phy-lane-no-swap;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_b>;
+	pinctrl-1 = <&i2c1_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+
+	codec@18 {
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		#sound-dai-cells = <0>;
+
+		ai3x-micbias-vg = <2>;
+
+		AVDD-supply = <&v3v3>;
+		IOVDD-supply = <&v3v3>;
+		DRVDD-supply = <&v3v3>;
+		DVDD-supply = <&v1v8_audio>;
+
+		clocks = <&sai2b>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tlv320_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+
+			tlv320_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+		};
+	};
+
+	touch@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpioi>;
+		vio-supply = <&v3v3>;
+		vcc-supply = <&v3v3>;
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	leds@62 {
+		compatible = "nxp,pca9533";
+		reg = <0x62>;
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			type = <PCA9532_TYPE_LED>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			type = <PCA9532_TYPE_LED>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	pmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&regulator_vin>;
+			buck2-supply = <&regulator_vin>;
+			buck3-supply = <&regulator_vin>;
+			buck4-supply = <&regulator_vin>;
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&regulator_vin>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			boost-supply = <&regulator_vin>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+
+			};
+
+			vdd_eth_2v5: ldo2 {
+				regulator-name = "dd_eth_2v5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			vdd_eth_1v0: ldo6 {
+				regulator-name = "vdd_eth_1v0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>,
+				     <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling",
+					  "onkey-rising";
+			power-off-time-sec = <10>;
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+		};
+	};
+
+	i2c4_eeprom: eeprom@50 {
+		compatible = "microchip,24c32",
+			     "atmel,24c32";
+		reg = <0x50>;
+	};
+
+	i2c4_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m_can2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can2_pins_a>;
+	pinctrl-1 = <&m_can2_sleep_pins_a>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b>, <&sai2b_pins_d>;
+	pinctrl-1 = <&sai2a_sleep_pins_b>, <&sai2b_sleep_pins_d>;
+	status = "okay";
+};
+
+&sai2a {
+	dma-names = "rx";
+	st,sync = <&sai2b 2>;
+	clocks = <&rcc SAI2_K>, <&sai2b>;
+	clock-names = "sai_ck", "MCLK";
+	#clock-cells = <0>;
+
+	sai2a_port: port {
+		sai2a_endpoint: endpoint {
+			remote-endpoint = <&tlv320_rx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sai2b {
+	dma-names = "tx";
+	#clock-cells = <0>;
+
+	sai2b_port: port {
+		sai2b_endpoint: endpoint {
+			remote-endpoint = <&tlv320_tx_endpoint>;
+			mclk-fs = <256>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_b>;
+	cd-gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_e>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_e>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+};
+
+&spi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_a>;
+	pinctrl-1 = <&spi1_sleep_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	pinctrl-3 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_b &usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_b &usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_b &usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_a>;
+	pinctrl-1 = <&usart3_sleep_pins_a>;
+	pinctrl-2 = <&usart3_idle_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
new file mode 100644
index 000000000000..b06a55a2fa18
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/ {
+	soc {
+		cryp1: cryp@54001000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54001000 0x400>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi
new file mode 100644
index 000000000000..35b1034aa3cf
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-drc02.dtsi
@@ -0,0 +1,169 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&gpiob {
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the STM32 UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <8 0>;
+		output-low;
+		line-name = "rs485-rx-en";
+	};
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DRC02-Out1",
+			  "DRC02-Out2", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "DRC02-In2", "", "", "",
+			  "", "", "", "";
+
+	/*
+	 * NOTE: The USB Hub on the DRC02 needs a reset signal to be
+	 * pulled high in order to be detected by the USB Controller.
+	 * This signal should be handled by USB power sequencing in
+	 * order to reset the Hub when USB bus is powered down, but
+	 * so far there is no such functionality.
+	 */
+	usb-hub-hog {
+		gpio-hog;
+		gpios = <2 0>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	touchscreen@49 {
+		status = "disabled";
+	};
+};
+
+&i2c5 {	/* TP7/TP8 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&sdmmc3 {
+	/*
+	 * On DRC02, the SoM does not have SDIO WiFi. The pins
+	 * are used for on-board microSD slot instead.
+	 */
+	/delete-property/broken-cd;
+	cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	/* Use PIO for the display */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";	/* Enable once there is display driver */
+	/*
+	 * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are
+	 * also connected to the display board connector.
+	 */
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/*
+ * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1),
+ *       however the STM32MP1 pinmux cannot map them to UART4 .
+ */
+
+&uart8 {	/* RS485 */
+	linux,rs485-enabled-at-boot-time;
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi
new file mode 100644
index 000000000000..46b87a27d8b3
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-pdk2.dtsi
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 3 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_panel_bl>;
+		status = "okay";
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		/*
+		 * The EXTi IRQ line 3 is shared with ethernet,
+		 * so mark this as polled GPIO key.
+		 */
+		button-0 {
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
+		/*
+		 * The EXTi IRQ line 0 is shared with PMIC,
+		 * so mark this as polled GPIO key.
+		 */
+		button-2 {
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			gpios = <&gpiog 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-3 {
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			gpios = <&gpiod 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:led5";
+			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "disabled";
+		};
+
+		led-1 {
+			label = "green:led6";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "green:led7";
+			gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "green:led8";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_panel_bl: regulator-panel-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_backlight";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_panel_supply>;
+	};
+
+	reg_panel_supply: regulator-panel-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "panel_supply";
+		regulator-min-microvolt = <24000000>;
+		regulator-max-microvolt = <24000000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		widgets = "Headphone", "Headphone Jack",
+			  "Line", "Line In Jack",
+			  "Microphone", "Microphone Jack";
+		routing = "Headphone Jack", "HP_OUT",
+			  "LINE_IN", "Line In Jack",
+			  "MIC_IN", "Microphone Jack",
+			  "Microphone Jack", "Mic Bias";
+		dais = <&sai2a_port &sai2b_port>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {	/* Header X22 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&i2c5 {	/* Header X21 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&v3v3>;
+		VDDIO-supply = <&vdd>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&sgtl5000_tx_endpoint>;
+				bitclock-master = <&sgtl5000_tx_endpoint>;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&sgtl5000_rx_endpoint>;
+				bitclock-master = <&sgtl5000_rx_endpoint>;
+			};
+		};
+
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-1 = <&ltdc_sleep_pins_b>;
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_tx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_rx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi
new file mode 100644
index 000000000000..abc595350e71
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-picoitx.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "yellow:led";
+			gpios = <&gpioi 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+};
+
+&adc {
+	status = "disabled";
+};
+
+&dac {
+	status = "disabled";
+};
+
+&fmc {
+	status = "disabled";
+};
+
+&gpioa {
+	/*
+	 * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable
+	 * port power. This signal should be handled by USB power sequencing
+	 * in order to turn on port power when USB bus is powered up, but so
+	 * far there is no such functionality.
+	 */
+	usb-port-power-hog {
+		gpio-hog;
+		gpios = <13 0>;
+		output-low;
+		line-name = "usb-port-power";
+	};
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "PicoITX-In1", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "PicoITX-Out1",
+			  "PicoITX-Out2", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "PicoITX-In2", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c2 {	/* On board-to-board connector (optional) */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c5 {	/* On board-to-board connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ksz8851 {
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi
new file mode 100644
index 000000000000..e61df23d361a
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcom-som.dtsi
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+};
+
+&adc1 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&adc2 {
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_c &mco2_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_c &mco2_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+			/* LAN8710Ai */
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
+			clocks = <&rcc CK_MCO2>;
+			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpioi>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-K", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-Q", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-E", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-B", "",
+			  "", "", "", "DHCOM-F",
+			  "DHCOM-D", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "", "DHCOM-P", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "DHCOM-A",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "DHCOM-C", "", "", "",
+			  "", "", "", "",
+			  "DHCOM-L", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DHCOM-N",
+			  "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U",
+			  "DHCOM-T", "", "DHCOM-S", "";
+};
+
+&gpioi {
+	gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I",
+			  "DHCOM-R", "DHCOM-M", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-always-on;
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&v3v3>;
+		interrupts-extended = <&gpioh 15 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rcc {
+	/* Connect MCO2 output to ETH_RX_CLK input via pad-pad connection */
+	clocks = <&rcc CK_MCO2>;
+	clock-names = "ETH_RX_CLK/ETH_REF_CLK";
+
+	/*
+	 * Set PLL4P output to 100 MHz to supply SDMMC with faster clock,
+	 * set MCO2 output to 50 MHz to supply ETHRX clock with PLL4P/2,
+	 * so that MCO2 behaves as a divider for the ETHRX clock here.
+	 */
+	assigned-clocks = <&rcc CK_MCO2>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <50000000>, <100000000>;
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep", "init";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>;
+	cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	st,cmd-gpios = <&gpiod 2 0>;
+	st,ck-gpios = <&gpioc 12 0>;
+	st,ckin-gpios = <&gpioe 4 0>;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+	/*
+	 * SD bus pull-up resistors:
+	 * - optional on SoMs with SD voltage translator
+	 * - mandatory on SoMs without SD voltage translator
+	 */
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi
new file mode 100644
index 000000000000..0069ad75d55e
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-avenger96.dtsi
@@ -0,0 +1,516 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
+#include "stm32mp15xx-dhcor-io1v8.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		serial2 = &usart2;
+		spi0 = &qspi;
+	};
+
+	/* XTal Q1 */
+	cec_clock: clk-cec-fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7513_out>;
+			};
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "green:user0";
+			gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led2 {
+			label = "green:user1";
+			gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led3 {
+			label = "green:user2";
+			gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led4 {
+			label = "green:user3";
+			gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32-AV96-HDMI";
+		dais = <&sai2a_port>;
+		status = "okay";
+	};
+
+	wlan_pwr: regulator-wlan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpioz 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+};
+
+&adc1 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@6 {
+		reg = <6>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&adc2 {
+	channel@0 {
+		reg = <0>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@1 {
+		reg = <1>;
+		st,min-sample-time-ns = <5000>;
+	};
+
+	channel@2 {
+		reg = <2>;
+		st,min-sample-time-ns = <5000>;
+	};
+};
+
+&dcmi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_c>;
+	pinctrl-1 = <&dcmi_sleep_pins_c>;
+	status = "disabled";
+
+	port {
+		dcmi_0: endpoint {
+			remote-endpoint = <&stmipi_2>;
+			bus-type = <5>;
+			bus-width = <8>;
+			pclk-sample = <0>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "AV96-K",
+			  "AV96-I", "", "AV96-A", "";
+};
+
+&gpiob {
+	gpio-line-names = "", "", "", "",
+			  "", "AV96-J", "", "",
+			  "", "", "", "AV96-B",
+			  "", "AV96-L", "", "";
+};
+
+&gpioc {
+	gpio-line-names = "", "", "", "AV96-C",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiod {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "AV96-D", "", "", "",
+			  "", "", "AV96-E", "AV96-F";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "AV96-G", "AV96-H", "", "";
+};
+
+&i2c1 {	/* X6 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c2 {	/* X6 I2C2 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_c>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	stmipi: stmipi@14 {
+		compatible = "st,st-mipid02";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&mco1_pins_a>;
+		pinctrl-1 = <&mco1_sleep_pins_a>;
+		reg = <0x14>;
+		clocks = <&rcc CK_MCO1>;
+		clock-names = "xclk";
+		assigned-clocks = <&rcc CK_MCO1>;
+		assigned-clock-parents = <&rcc CK_HSE>;
+		assigned-clock-rates = <24000000>;
+		VDDE-supply = <&v1v8>;
+		VDDIN-supply = <&v1v8>;
+		reset-gpios = <&gpioz 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stmipi_0: endpoint {
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				stmipi_2: endpoint {
+					bus-width = <8>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+					pclk-sample = <0>;
+					remote-endpoint = <&dcmi_0>;
+				};
+			};
+		};
+	};
+
+	hdmi-transmitter@3d {
+		compatible = "adi,adv7513";
+		reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
+		reg-names = "main", "edid", "cec", "packet";
+		clocks = <&cec_clock>;
+		clock-names = "cec";
+
+		avdd-supply = <&v3v3>;
+		dvdd-supply = <&v3v3>;
+		pvdd-supply = <&v3v3>;
+		dvdd-3v-supply = <&v3v3>;
+		bgvdd-supply = <&v3v3>;
+
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+
+		status = "okay";
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7513_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7513_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				adv7513_i2s0: endpoint {
+					remote-endpoint = <&sai2a_endpoint>;
+				};
+			};
+		};
+	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_d>;
+	pinctrl-1 = <&ltdc_sleep_pins_d>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&adv7513_in>;
+		};
+	};
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_c>;
+	pinctrl-1 = <&sai2a_sleep_pins_c>;
+	clock-names = "pclk", "x8k", "x11k";
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&adv7513_i2s0>;
+				dai-format = "i2s";
+				mclk-fs = <256>;
+			};
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd_io>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	broken-cd;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&wlan_pwr>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	brcmf: bcrmf@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	/* On Low speed expansion header */
+	label = "LS-UART1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	/* On Low speed expansion header */
+	label = "LS-UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+/* Bluetooth */
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	status = "okay";
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi
new file mode 100644
index 000000000000..92d906bfd5d7
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-drc-compact.dtsi
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		mmc0 = &sdmmc1;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+		serial0 = &uart4;
+		serial1 = &uart8;
+		serial2 = &usart3;
+		serial3 = &uart5;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "yellow:user0";
+			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "red:user1";
+			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {	/* X11 ADC inputs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@2 {
+			reg = <2>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "DRCC-VAR2", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "DRCC-GPIO0", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "DRCC-GPIO5", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "DRCC-HW2",
+			  "DRCC-GPIO4", "", "", "",
+			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
+			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DRCC-GPIO2",
+			  "", "DRCC-GPIO1", "", "",
+			  "", "", "", "";
+};
+
+&i2c1 {	/* X11 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {	/* MicroSD */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc2 {	/* eMMC */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	bus-width = <4>;
+	mmc-ddr-3_3v;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi2 {	/* X11 SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	label = "UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_d>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart5 {	/* X11 UART */
+	label = "X11-UART5";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	label = "RS485-1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart3 {	/* RS485 or RS232 */
+	label = "RS485-2";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart3_pins_e>;
+	pinctrl-1 = <&usart3_sleep_pins_e>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi
new file mode 100644
index 000000000000..9937b28548c2
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-io1v8.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	/* Enpirion EP3A8LQI U2 on the DHCOR */
+	vdd_io: regulator-buck-io {
+		compatible = "regulator-fixed";
+		regulator-name = "buck-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&vdd {
+	regulator-min-microvolt = <2900000>;
+	regulator-max-microvolt = <2900000>;
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd_io>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi
new file mode 100644
index 000000000000..bba19f21e527
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-som.dtsi
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
+ * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+ * Copyright (C) 2020 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		spi0 = &qspi;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				regulator-enable-ramp-delay = <300000>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi
new file mode 100644
index 000000000000..ab7f0ba49639
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dhcor-testbench.dtsi
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		serial0 = &uart4;
+		serial1 = &uart7;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sd_switch: regulator-sd_switch {
+		compatible = "regulator-gpio";
+		regulator-name = "sd_switch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+		regulator-always-on;
+
+		gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1>,
+			 <2900000 0x0>;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@6 {
+			reg = <6>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+
+	adc2: adc@100 {
+		status = "okay";
+		channel@0 {
+			reg = <0>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@1 {
+			reg = <1>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@2 {
+			reg = <2>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&i2c4 {
+	dh_mac_eeprom: eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	vqmmc-supply = <&sd_switch>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	status = "okay";
+	vbus-supply = <&vbus_otg>;
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-dkx.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-dkx.dtsi
new file mode 100644
index 000000000000..511113f2e399
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-dkx.dtsi
@@ -0,0 +1,741 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart7;
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led-blue {
+			label = "heartbeat";
+			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		label = "STM32MP15-DK";
+		routing =
+			"Playback" , "MCLK",
+			"Capture" , "MCLK",
+			"MICL" , "Mic Bias";
+		dais = <&sai2a_port &sai2b_port &i2s2_port>;
+		status = "okay";
+	};
+
+	vin: vin {
+		compatible = "regulator-fixed";
+		regulator-name = "vin";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_usb_cc_pins_a>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+	adc1: adc@0 {
+		status = "okay";
+		/*
+		 * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
+		 * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
+		 * 5 * (56 + 47kOhms) * 5pF => 2.5us.
+		 * Use arbitrary margin here (e.g. 5us).
+		 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+	adc2: adc@100 {
+		status = "okay";
+		/* USB Type-C CC1 & CC2 */
+		channel@18 {
+			reg = <18>;
+			st,min-sample-time-ns = <5000>;
+		};
+		channel@19 {
+			reg = <19>;
+			st,min-sample-time-ns = <5000>;
+		};
+	};
+};
+
+&cec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cec_pins_b>;
+	pinctrl-1 = <&cec_sleep_pins_b>;
+	status = "okay";
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii-id";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	hdmi-transmitter@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		iovcc-supply = <&v3v3_hdmi>;
+		cvcc12-supply = <&v1v2_hdmi>;
+		reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpiog>;
+		#sound-dai-cells = <0>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sii9022_in: endpoint {
+					remote-endpoint = <&ltdc_ep0_out>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				sii9022_tx_endpoint: endpoint {
+					remote-endpoint = <&i2s2_endpoint>;
+				};
+			};
+		};
+	};
+
+	cs42l51: cs42l51@4a {
+		compatible = "cirrus,cs42l51";
+		reg = <0x4a>;
+		#sound-dai-cells = <0>;
+		VL-supply = <&v3v3>;
+		VD-supply = <&v1v8_audio>;
+		VA-supply = <&v1v8_audio>;
+		VAHP-supply = <&v1v8_audio>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		clocks = <&sai2a>;
+		clock-names = "MCLK";
+		status = "okay";
+
+		cs42l51_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cs42l51_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master = <&cs42l51_tx_endpoint>;
+				bitclock-master = <&cs42l51_tx_endpoint>;
+			};
+
+			cs42l51_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master = <&cs42l51_rx_endpoint>;
+				bitclock-master = <&cs42l51_rx_endpoint>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	stusb1600@28 {
+		compatible = "st,stusb1600";
+		reg = <0x28>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpioi>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&stusb1600_pins_a>;
+		status = "okay";
+		vdd-supply = <&vin>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			typec-power-opmode = "default";
+
+			port {
+				con_usbotg_hs_ep: endpoint {
+					remote-endpoint = <&usbotg_hs_ep>;
+				};
+			};
+		};
+	};
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			buck1-supply = <&vin>;
+			buck2-supply = <&vin>;
+			buck3-supply = <&vin>;
+			buck4-supply = <&vin>;
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&vin>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo4-supply = <&vin>;
+			ldo5-supply = <&vin>;
+			ldo6-supply = <&v3v3>;
+			vref_ddr-supply = <&vin>;
+			boost-supply = <&vin>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	clock-frequency = <400000>;
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&i2s2 {
+	clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "i2sclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2s2_pins_a>;
+	pinctrl-1 = <&i2s2_sleep_pins_a>;
+	status = "okay";
+
+	i2s2_port: port {
+		i2s2_endpoint: endpoint {
+			remote-endpoint = <&sii9022_tx_endpoint>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+		};
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_a>;
+	pinctrl-1 = <&ltdc_sleep_pins_a>;
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_tx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&cs42l51_rx_endpoint>;
+				dai-format = "i2s";
+				mclk-fs = <256>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+			};
+		};
+	};
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "disabled";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm1_pins_a>;
+		pinctrl-1 = <&pwm1_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers3 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm3_pins_a>;
+		pinctrl-1 = <&pwm3_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@2 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	timer@5 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-1 = <&pwm12_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart7_pins_c>;
+	pinctrl-1 = <&uart7_sleep_pins_c>;
+	pinctrl-2 = <&uart7_idle_pins_c>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_c>;
+	pinctrl-1 = <&usart3_sleep_pins_c>;
+	pinctrl-2 = <&usart3_idle_pins_c>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3>;
+	};
+};
+
+&usbotg_hs {
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usbotg_hs_ep: endpoint {
+			remote-endpoint = <&con_usbotg_hs_ep>;
+		};
+	};
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi
new file mode 100644
index 000000000000..a43965c86fe8
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xx-osd32.dtsi
@@ -0,0 +1,222 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdda: ldo5 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v2_hdmi: ldo6 {
+				regulator-name = "v1v2_hdmi";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge = <1>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge = <1>;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+		};
+
+		pmic_watchdog: watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	sip_eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		vcc-supply = <&vdd>;
+		reg = <0x50>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>;
+	mbox-names = "vq0", "vq1", "shutdown", "detach";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&rng1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi
new file mode 100644
index 000000000000..04f7a43ad66f
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxaa-pinctrl.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AA>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@5000a000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 128 16>;
+	};
+
+	gpioj: gpio@5000b000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 144 16>;
+	};
+
+	gpiok: gpio@5000c000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl 0 160 8>;
+	};
+};
+
+&pinctrl_z {
+	st,package = <STM32MP_PKG_AA>;
+
+	gpioz: gpio@54004000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl_z 0 400 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi
new file mode 100644
index 000000000000..328dad140e9b
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxab-pinctrl.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AB>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <6>;
+		gpio-ranges = <&pinctrl 6 86 6>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl 6 102 10>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <2>;
+		gpio-ranges = <&pinctrl 0 112 2>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi
new file mode 100644
index 000000000000..7eaa245f44db
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxac-pinctrl.dtsi
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AC>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 80 16>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 96 16>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 112 16>;
+	};
+
+	gpioi: gpio@5000a000 {
+		status = "okay";
+		ngpios = <12>;
+		gpio-ranges = <&pinctrl 0 128 12>;
+	};
+};
+
+&pinctrl_z {
+	st,package = <STM32MP_PKG_AC>;
+
+	gpioz: gpio@54004000 {
+		status = "okay";
+		ngpios = <8>;
+		gpio-ranges = <&pinctrl_z 0 400 8>;
+	};
+};
diff --git a/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi
new file mode 100644
index 000000000000..b63e207de216
--- /dev/null
+++ b/arch/arm/boot/dts/st/stm32mp15xxad-pinctrl.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+&pinctrl {
+	st,package = <STM32MP_PKG_AD>;
+
+	gpioa: gpio@50002000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 0 16>;
+	};
+
+	gpiob: gpio@50003000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 16 16>;
+	};
+
+	gpioc: gpio@50004000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 32 16>;
+	};
+
+	gpiod: gpio@50005000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 48 16>;
+	};
+
+	gpioe: gpio@50006000 {
+		status = "okay";
+		ngpios = <16>;
+		gpio-ranges = <&pinctrl 0 64 16>;
+	};
+
+	gpiof: gpio@50007000 {
+		status = "okay";
+		ngpios = <6>;
+		gpio-ranges = <&pinctrl 6 86 6>;
+	};
+
+	gpiog: gpio@50008000 {
+		status = "okay";
+		ngpios = <10>;
+		gpio-ranges = <&pinctrl 6 102 10>;
+	};
+
+	gpioh: gpio@50009000 {
+		status = "okay";
+		ngpios = <2>;
+		gpio-ranges = <&pinctrl 0 112 2>;
+	};
+};