diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/sja1105.txt')
-rw-r--r-- | Documentation/devicetree/bindings/net/dsa/sja1105.txt | 121 |
1 files changed, 0 insertions, 121 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/sja1105.txt b/Documentation/devicetree/bindings/net/dsa/sja1105.txt deleted file mode 100644 index dcf3b2c1d26b..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/sja1105.txt +++ /dev/null @@ -1,121 +0,0 @@ -NXP SJA1105 switch driver -========================= - -Required properties: - -- compatible: - Must be one of: - - "nxp,sja1105e" - - "nxp,sja1105t" - - "nxp,sja1105p" - - "nxp,sja1105q" - - "nxp,sja1105r" - - "nxp,sja1105s" - - Although the device ID could be detected at runtime, explicit bindings - are required in order to be able to statically check their validity. - For example, SGMII can only be specified on port 4 of R and S devices, - and the non-SGMII devices, while pin-compatible, are not equal in terms - of support for RGMII internal delays (supported on P/Q/R/S, but not on - E/T). - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for the list of standard -DSA required and optional properties. - -Other observations ------------------- - -The SJA1105 SPI interface requires a CS-to-CLK time (t2 in UM10944) of at least -one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum -cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed -depends on the SPI bus master driver. - -Example -------- - -Ethernet switch connected via SPI to the host, CPU port wired to enet2: - -arch/arm/boot/dts/ls1021a-tsn.dts: - -/* SPI controller of the LS1021 */ -&dspi0 { - sja1105@1 { - reg = <0x1>; - #address-cells = <1>; - #size-cells = <0>; - compatible = "nxp,sja1105t"; - spi-max-frequency = <4000000>; - fsl,spi-cs-sck-delay = <1000>; - fsl,spi-sck-cs-delay = <1000>; - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - /* ETH5 written on chassis */ - label = "swp5"; - phy-handle = <&rgmii_phy6>; - phy-mode = "rgmii-id"; - reg = <0>; - }; - port@1 { - /* ETH2 written on chassis */ - label = "swp2"; - phy-handle = <&rgmii_phy3>; - phy-mode = "rgmii-id"; - reg = <1>; - }; - port@2 { - /* ETH3 written on chassis */ - label = "swp3"; - phy-handle = <&rgmii_phy4>; - phy-mode = "rgmii-id"; - reg = <2>; - }; - port@3 { - /* ETH4 written on chassis */ - phy-handle = <&rgmii_phy5>; - label = "swp4"; - phy-mode = "rgmii-id"; - reg = <3>; - }; - port@4 { - /* Internal port connected to eth2 */ - ethernet = <&enet2>; - phy-mode = "rgmii"; - reg = <4>; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; -}; - -/* MDIO controller of the LS1021 */ -&mdio0 { - /* BCM5464 */ - rgmii_phy3: ethernet-phy@3 { - reg = <0x3>; - }; - rgmii_phy4: ethernet-phy@4 { - reg = <0x4>; - }; - rgmii_phy5: ethernet-phy@5 { - reg = <0x5>; - }; - rgmii_phy6: ethernet-phy@6 { - reg = <0x6>; - }; -}; - -/* Ethernet master port of the LS1021 */ -&enet2 { - phy-connection-type = "rgmii"; - status = "ok"; - fixed-link { - speed = <1000>; - full-duplex; - }; -}; |