summaryrefslogtreecommitdiff
path: root/drivers/pci/controller/pci-mvebu.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pci/controller/pci-mvebu.c')
-rw-r--r--drivers/pci/controller/pci-mvebu.c542
1 files changed, 404 insertions, 138 deletions
diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c
index ed13e81cd691..71258ea3d35f 100644
--- a/drivers/pci/controller/pci-mvebu.c
+++ b/drivers/pci/controller/pci-mvebu.c
@@ -6,6 +6,7 @@
*/
#include <linux/kernel.h>
+#include <linux/module.h>
#include <linux/pci.h>
#include <linux/clk.h>
#include <linux/delay.h>
@@ -51,10 +52,14 @@
PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where) | \
PCIE_CONF_ADDR_EN)
#define PCIE_CONF_DATA_OFF 0x18fc
+#define PCIE_INT_CAUSE_OFF 0x1900
+#define PCIE_INT_PM_PME BIT(28)
#define PCIE_MASK_OFF 0x1910
#define PCIE_MASK_ENABLE_INTS 0x0f000000
#define PCIE_CTRL_OFF 0x1a00
#define PCIE_CTRL_X1_MODE 0x0001
+#define PCIE_CTRL_RC_MODE BIT(1)
+#define PCIE_CTRL_MASTER_HOT_RESET BIT(24)
#define PCIE_STAT_OFF 0x1a04
#define PCIE_STAT_BUS 0xff00
#define PCIE_STAT_DEV 0x1f0000
@@ -125,6 +130,11 @@ static bool mvebu_pcie_link_up(struct mvebu_pcie_port *port)
return !(mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN);
}
+static u8 mvebu_pcie_get_local_bus_nr(struct mvebu_pcie_port *port)
+{
+ return (mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_BUS) >> 8;
+}
+
static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie_port *port, int nr)
{
u32 stat;
@@ -145,22 +155,13 @@ static void mvebu_pcie_set_local_dev_nr(struct mvebu_pcie_port *port, int nr)
mvebu_writel(port, stat, PCIE_STAT_OFF);
}
-/*
- * Setup PCIE BARs and Address Decode Wins:
- * BAR[0] -> internal registers (needed for MSI)
- * BAR[1] -> covers all DRAM banks
- * BAR[2] -> Disabled
- * WIN[0-3] -> DRAM bank[0-3]
- */
-static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
+static void mvebu_pcie_disable_wins(struct mvebu_pcie_port *port)
{
- const struct mbus_dram_target_info *dram;
- u32 size;
int i;
- dram = mv_mbus_dram_info();
+ mvebu_writel(port, 0, PCIE_BAR_LO_OFF(0));
+ mvebu_writel(port, 0, PCIE_BAR_HI_OFF(0));
- /* First, disable and clear BARs and windows. */
for (i = 1; i < 3; i++) {
mvebu_writel(port, 0, PCIE_BAR_CTRL_OFF(i));
mvebu_writel(port, 0, PCIE_BAR_LO_OFF(i));
@@ -176,6 +177,25 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
mvebu_writel(port, 0, PCIE_WIN5_CTRL_OFF);
mvebu_writel(port, 0, PCIE_WIN5_BASE_OFF);
mvebu_writel(port, 0, PCIE_WIN5_REMAP_OFF);
+}
+
+/*
+ * Setup PCIE BARs and Address Decode Wins:
+ * BAR[0] -> internal registers (needed for MSI)
+ * BAR[1] -> covers all DRAM banks
+ * BAR[2] -> Disabled
+ * WIN[0-3] -> DRAM bank[0-3]
+ */
+static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
+{
+ const struct mbus_dram_target_info *dram;
+ u32 size;
+ int i;
+
+ dram = mv_mbus_dram_info();
+
+ /* First, disable and clear BARs and windows. */
+ mvebu_pcie_disable_wins(port);
/* Setup windows for DDR banks. Count total DDR size on the fly. */
size = 0;
@@ -213,18 +233,47 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port)
static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port)
{
- u32 cmd, mask;
+ u32 ctrl, cmd, dev_rev, mask;
- /* Point PCIe unit MBUS decode windows to DRAM space. */
- mvebu_pcie_setup_wins(port);
+ /* Setup PCIe controller to Root Complex mode. */
+ ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+ ctrl |= PCIE_CTRL_RC_MODE;
+ mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
- /* Master + slave enable. */
+ /* Disable Root Bridge I/O space, memory space and bus mastering. */
cmd = mvebu_readl(port, PCIE_CMD_OFF);
- cmd |= PCI_COMMAND_IO;
- cmd |= PCI_COMMAND_MEMORY;
- cmd |= PCI_COMMAND_MASTER;
+ cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
mvebu_writel(port, cmd, PCIE_CMD_OFF);
+ /*
+ * Change Class Code of PCI Bridge device to PCI Bridge (0x6004)
+ * because default value is Memory controller (0x5080).
+ *
+ * Note that this mvebu PCI Bridge does not have compliant Type 1
+ * Configuration Space. Header Type is reported as Type 0 and it
+ * has format of Type 0 config space.
+ *
+ * Moreover Type 0 BAR registers (ranges 0x10 - 0x28 and 0x30 - 0x34)
+ * have the same format in Marvell's specification as in PCIe
+ * specification, but their meaning is totally different and they do
+ * different things: they are aliased into internal mvebu registers
+ * (e.g. PCIE_BAR_LO_OFF) and these should not be changed or
+ * reconfigured by pci device drivers.
+ *
+ * Therefore driver uses emulation of PCI Bridge which emulates
+ * access to configuration space via internal mvebu registers or
+ * emulated configuration buffer. Driver access these PCI Bridge
+ * directly for simplification, but these registers can be accessed
+ * also via standard mvebu way for accessing PCI config space.
+ */
+ dev_rev = mvebu_readl(port, PCIE_DEV_REV_OFF);
+ dev_rev &= ~0xffffff00;
+ dev_rev |= (PCI_CLASS_BRIDGE_PCI << 8) << 8;
+ mvebu_writel(port, dev_rev, PCIE_DEV_REV_OFF);
+
+ /* Point PCIe unit MBUS decode windows to DRAM space. */
+ mvebu_pcie_setup_wins(port);
+
/* Enable interrupt lines A-D. */
mask = mvebu_readl(port, PCIE_MASK_OFF);
mask |= PCIE_MASK_ENABLE_INTS;
@@ -250,6 +299,9 @@ static int mvebu_pcie_hw_rd_conf(struct mvebu_pcie_port *port,
case 4:
*val = readl_relaxed(conf_data);
break;
+ default:
+ *val = 0xffffffff;
+ return PCIBIOS_BAD_REGISTER_NUMBER;
}
return PCIBIOS_SUCCESSFUL;
@@ -303,7 +355,7 @@ static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
* areas each having a power of two size. We start from the largest
* one (i.e highest order bit set in the size).
*/
-static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+static int mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
unsigned int target, unsigned int attribute,
phys_addr_t base, size_t size,
phys_addr_t remap)
@@ -324,7 +376,7 @@ static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
&base, &end, ret);
mvebu_pcie_del_windows(port, base - size_mapped,
size_mapped);
- return;
+ return ret;
}
size -= sz;
@@ -333,16 +385,20 @@ static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
if (remap != MVEBU_MBUS_NO_REMAP)
remap += sz;
}
+
+ return 0;
}
-static void mvebu_pcie_set_window(struct mvebu_pcie_port *port,
+static int mvebu_pcie_set_window(struct mvebu_pcie_port *port,
unsigned int target, unsigned int attribute,
const struct mvebu_pcie_window *desired,
struct mvebu_pcie_window *cur)
{
+ int ret;
+
if (desired->base == cur->base && desired->remap == cur->remap &&
desired->size == cur->size)
- return;
+ return 0;
if (cur->size != 0) {
mvebu_pcie_del_windows(port, cur->base, cur->size);
@@ -357,31 +413,35 @@ static void mvebu_pcie_set_window(struct mvebu_pcie_port *port,
}
if (desired->size == 0)
- return;
+ return 0;
+
+ ret = mvebu_pcie_add_windows(port, target, attribute, desired->base,
+ desired->size, desired->remap);
+ if (ret) {
+ cur->size = 0;
+ cur->base = 0;
+ return ret;
+ }
- mvebu_pcie_add_windows(port, target, attribute, desired->base,
- desired->size, desired->remap);
*cur = *desired;
+ return 0;
}
-static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
+static int mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
{
struct mvebu_pcie_window desired = {};
struct pci_bridge_emul_conf *conf = &port->bridge.conf;
/* Are the new iobase/iolimit values invalid? */
if (conf->iolimit < conf->iobase ||
- conf->iolimitupper < conf->iobaseupper ||
- !(conf->command & PCI_COMMAND_IO)) {
- mvebu_pcie_set_window(port, port->io_target, port->io_attr,
- &desired, &port->iowin);
- return;
- }
+ conf->iolimitupper < conf->iobaseupper)
+ return mvebu_pcie_set_window(port, port->io_target, port->io_attr,
+ &desired, &port->iowin);
if (!mvebu_has_ioport(port)) {
dev_WARN(&port->pcie->pdev->dev,
"Attempt to set IO when IO is disabled\n");
- return;
+ return -EOPNOTSUPP;
}
/*
@@ -399,22 +459,19 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
desired.remap) +
1;
- mvebu_pcie_set_window(port, port->io_target, port->io_attr, &desired,
- &port->iowin);
+ return mvebu_pcie_set_window(port, port->io_target, port->io_attr, &desired,
+ &port->iowin);
}
-static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
+static int mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
{
struct mvebu_pcie_window desired = {.remap = MVEBU_MBUS_NO_REMAP};
struct pci_bridge_emul_conf *conf = &port->bridge.conf;
/* Are the new membase/memlimit values invalid? */
- if (conf->memlimit < conf->membase ||
- !(conf->command & PCI_COMMAND_MEMORY)) {
- mvebu_pcie_set_window(port, port->mem_target, port->mem_attr,
- &desired, &port->memwin);
- return;
- }
+ if (conf->memlimit < conf->membase)
+ return mvebu_pcie_set_window(port, port->mem_target, port->mem_attr,
+ &desired, &port->memwin);
/*
* We read the PCI-to-PCI bridge emulated registers, and
@@ -426,8 +483,56 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
desired.size = (((conf->memlimit & 0xFFF0) << 16) | 0xFFFFF) -
desired.base + 1;
- mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, &desired,
- &port->memwin);
+ return mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, &desired,
+ &port->memwin);
+}
+
+static pci_bridge_emul_read_status_t
+mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge,
+ int reg, u32 *value)
+{
+ struct mvebu_pcie_port *port = bridge->data;
+
+ switch (reg) {
+ case PCI_COMMAND:
+ *value = mvebu_readl(port, PCIE_CMD_OFF);
+ break;
+
+ case PCI_PRIMARY_BUS: {
+ /*
+ * From the whole 32bit register we support reading from HW only
+ * secondary bus number which is mvebu local bus number.
+ * Other bits are retrieved only from emulated config buffer.
+ */
+ __le32 *cfgspace = (__le32 *)&bridge->conf;
+ u32 val = le32_to_cpu(cfgspace[PCI_PRIMARY_BUS / 4]);
+ val &= ~0xff00;
+ val |= mvebu_pcie_get_local_bus_nr(port) << 8;
+ *value = val;
+ break;
+ }
+
+ case PCI_INTERRUPT_LINE: {
+ /*
+ * From the whole 32bit register we support reading from HW only
+ * one bit: PCI_BRIDGE_CTL_BUS_RESET.
+ * Other bits are retrieved only from emulated config buffer.
+ */
+ __le32 *cfgspace = (__le32 *)&bridge->conf;
+ u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]);
+ if (mvebu_readl(port, PCIE_CTRL_OFF) & PCIE_CTRL_MASTER_HOT_RESET)
+ val |= PCI_BRIDGE_CTL_BUS_RESET << 16;
+ else
+ val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16);
+ *value = val;
+ break;
+ }
+
+ default:
+ return PCI_BRIDGE_EMUL_NOT_HANDLED;
+ }
+
+ return PCI_BRIDGE_EMUL_HANDLED;
}
static pci_bridge_emul_read_status_t
@@ -442,9 +547,7 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
break;
case PCI_EXP_DEVCTL:
- *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL) &
- ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
- PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
break;
case PCI_EXP_LNKCAP:
@@ -468,6 +571,18 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge,
*value = mvebu_readl(port, PCIE_RC_RTSTA);
break;
+ case PCI_EXP_DEVCAP2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCAP2);
+ break;
+
+ case PCI_EXP_DEVCTL2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+ break;
+
+ case PCI_EXP_LNKCTL2:
+ *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+ break;
+
default:
return PCI_BRIDGE_EMUL_NOT_HANDLED;
}
@@ -484,39 +599,62 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge,
switch (reg) {
case PCI_COMMAND:
- {
- if (!mvebu_has_ioport(port))
- conf->command &= ~PCI_COMMAND_IO;
-
- if ((old ^ new) & PCI_COMMAND_IO)
- mvebu_pcie_handle_iobase_change(port);
- if ((old ^ new) & PCI_COMMAND_MEMORY)
- mvebu_pcie_handle_membase_change(port);
+ if (!mvebu_has_ioport(port)) {
+ conf->command = cpu_to_le16(
+ le16_to_cpu(conf->command) & ~PCI_COMMAND_IO);
+ new &= ~PCI_COMMAND_IO;
+ }
+ mvebu_writel(port, new, PCIE_CMD_OFF);
break;
- }
case PCI_IO_BASE:
- /*
- * We keep bit 1 set, it is a read-only bit that
- * indicates we support 32 bits addressing for the
- * I/O
- */
- conf->iobase |= PCI_IO_RANGE_TYPE_32;
- conf->iolimit |= PCI_IO_RANGE_TYPE_32;
- mvebu_pcie_handle_iobase_change(port);
+ if ((mask & 0xffff) && mvebu_pcie_handle_iobase_change(port)) {
+ /* On error disable IO range */
+ conf->iobase &= ~0xf0;
+ conf->iolimit &= ~0xf0;
+ conf->iobaseupper = cpu_to_le16(0x0000);
+ conf->iolimitupper = cpu_to_le16(0x0000);
+ if (mvebu_has_ioport(port))
+ conf->iobase |= 0xf0;
+ }
break;
case PCI_MEMORY_BASE:
- mvebu_pcie_handle_membase_change(port);
+ if (mvebu_pcie_handle_membase_change(port)) {
+ /* On error disable mem range */
+ conf->membase = cpu_to_le16(le16_to_cpu(conf->membase) & ~0xfff0);
+ conf->memlimit = cpu_to_le16(le16_to_cpu(conf->memlimit) & ~0xfff0);
+ conf->membase = cpu_to_le16(le16_to_cpu(conf->membase) | 0xfff0);
+ }
break;
case PCI_IO_BASE_UPPER16:
- mvebu_pcie_handle_iobase_change(port);
+ if (mvebu_pcie_handle_iobase_change(port)) {
+ /* On error disable IO range */
+ conf->iobase &= ~0xf0;
+ conf->iolimit &= ~0xf0;
+ conf->iobaseupper = cpu_to_le16(0x0000);
+ conf->iolimitupper = cpu_to_le16(0x0000);
+ if (mvebu_has_ioport(port))
+ conf->iobase |= 0xf0;
+ }
break;
case PCI_PRIMARY_BUS:
- mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+ if (mask & 0xff00)
+ mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus);
+ break;
+
+ case PCI_INTERRUPT_LINE:
+ if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) {
+ u32 ctrl = mvebu_readl(port, PCIE_CTRL_OFF);
+ if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16))
+ ctrl |= PCIE_CTRL_MASTER_HOT_RESET;
+ else
+ ctrl &= ~PCIE_CTRL_MASTER_HOT_RESET;
+ mvebu_writel(port, ctrl, PCIE_CTRL_OFF);
+ }
break;
default:
@@ -532,13 +670,6 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,
switch (reg) {
case PCI_EXP_DEVCTL:
- /*
- * Armada370 data says these bits must always
- * be zero when in root complex mode.
- */
- new &= ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE |
- PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE);
-
mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL);
break;
@@ -555,12 +686,31 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge,
break;
case PCI_EXP_RTSTA:
- mvebu_writel(port, new, PCIE_RC_RTSTA);
+ /*
+ * PME Status bit in Root Status Register (PCIE_RC_RTSTA)
+ * is read-only and can be cleared only by writing 0b to the
+ * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So
+ * clear PME via Interrupt Cause.
+ */
+ if (new & PCI_EXP_RTSTA_PME)
+ mvebu_writel(port, ~PCIE_INT_PM_PME, PCIE_INT_CAUSE_OFF);
+ break;
+
+ case PCI_EXP_DEVCTL2:
+ mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2);
+ break;
+
+ case PCI_EXP_LNKCTL2:
+ mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2);
+ break;
+
+ default:
break;
}
}
static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = {
+ .read_base = mvebu_pci_bridge_emul_base_conf_read,
.write_base = mvebu_pci_bridge_emul_base_conf_write,
.read_pcie = mvebu_pci_bridge_emul_pcie_conf_read,
.write_pcie = mvebu_pci_bridge_emul_pcie_conf_write,
@@ -570,9 +720,11 @@ static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = {
* Initialize the configuration space of the PCI-to-PCI bridge
* associated with the given PCIe interface.
*/
-static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
+static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
{
struct pci_bridge_emul *bridge = &port->bridge;
+ u32 pcie_cap = mvebu_readl(port, PCIE_CAP_PCIEXP);
+ u8 pcie_cap_ver = ((pcie_cap >> 16) & PCI_EXP_FLAGS_VERS);
bridge->conf.vendor = PCI_VENDOR_ID_MARVELL;
bridge->conf.device = mvebu_readl(port, PCIE_DEV_ID_OFF) >> 16;
@@ -585,11 +737,17 @@ static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port)
bridge->conf.iolimit = PCI_IO_RANGE_TYPE_32;
}
+ /*
+ * Older mvebu hardware provides PCIe Capability structure only in
+ * version 1. New hardware provides it in version 2.
+ */
+ bridge->pcie_conf.cap = cpu_to_le16(pcie_cap_ver);
+
bridge->has_pcie = true;
bridge->data = port;
bridge->ops = &mvebu_pci_bridge_emul_ops;
- pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
+ return pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR);
}
static inline struct mvebu_pcie *sys_to_pcie(struct pci_sys_data *sys)
@@ -606,6 +764,9 @@ static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie,
for (i = 0; i < pcie->nports; i++) {
struct mvebu_pcie_port *port = &pcie->ports[i];
+ if (!port->base)
+ continue;
+
if (bus->number == 0 && port->devfn == devfn)
return port;
if (bus->number != 0 &&
@@ -653,20 +814,16 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
int ret;
port = mvebu_pcie_find_port(pcie, bus, devfn);
- if (!port) {
- *val = 0xffffffff;
+ if (!port)
return PCIBIOS_DEVICE_NOT_FOUND;
- }
/* Access the emulated PCI-to-PCI bridge */
if (bus->number == 0)
return pci_bridge_emul_conf_read(&port->bridge, where,
size, val);
- if (!mvebu_pcie_link_up(port)) {
- *val = 0xffffffff;
+ if (!mvebu_pcie_link_up(port))
return PCIBIOS_DEVICE_NOT_FOUND;
- }
/* Access the real PCIe interface */
ret = mvebu_pcie_hw_rd_conf(port, bus, devfn,
@@ -680,6 +837,15 @@ static struct pci_ops mvebu_pcie_ops = {
.write = mvebu_pcie_wr_conf,
};
+static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+ /* Interrupt support on mvebu emulated bridges is not implemented yet */
+ if (dev->bus->number == 0)
+ return 0; /* Proper return code 0 == NO_IRQ */
+
+ return of_irq_parse_and_map_pci(dev, slot, pin);
+}
+
static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev,
const struct resource *res,
resource_size_t start,
@@ -781,6 +947,8 @@ static int mvebu_pcie_suspend(struct device *dev)
pcie = dev_get_drvdata(dev);
for (i = 0; i < pcie->nports; i++) {
struct mvebu_pcie_port *port = pcie->ports + i;
+ if (!port->base)
+ continue;
port->saved_pcie_stat = mvebu_readl(port, PCIE_STAT_OFF);
}
@@ -795,6 +963,8 @@ static int mvebu_pcie_resume(struct device *dev)
pcie = dev_get_drvdata(dev);
for (i = 0; i < pcie->nports; i++) {
struct mvebu_pcie_port *port = pcie->ports + i;
+ if (!port->base)
+ continue;
mvebu_writel(port, port->saved_pcie_stat, PCIE_STAT_OFF);
mvebu_pcie_setup_hw(port);
}
@@ -838,6 +1008,11 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie,
port->devfn = of_pci_get_devfn(child);
if (port->devfn < 0)
goto skip;
+ if (PCI_FUNC(port->devfn) != 0) {
+ dev_err(dev, "%s: invalid function number, must be zero\n",
+ port->name);
+ goto skip;
+ }
ret = mvebu_get_tgt_attr(dev->of_node, port->devfn, IORESOURCE_MEM,
&port->mem_target, &port->mem_attr);
@@ -992,6 +1167,10 @@ static int mvebu_pcie_parse_request_resources(struct mvebu_pcie *pcie)
resource_size(&pcie->io) - 1);
pcie->realio.name = "PCI I/O";
+ ret = devm_pci_remap_iospace(dev, &pcie->realio, pcie->io.start);
+ if (ret)
+ return ret;
+
pci_add_resource(&bridge->windows, &pcie->realio);
ret = devm_request_resource(dev, &ioport_resource, &pcie->realio);
if (ret)
@@ -1001,54 +1180,6 @@ static int mvebu_pcie_parse_request_resources(struct mvebu_pcie *pcie)
return 0;
}
-/*
- * This is a copy of pci_host_probe(), except that it does the I/O
- * remap as the last step, once we are sure we won't fail.
- *
- * It should be removed once the I/O remap error handling issue has
- * been sorted out.
- */
-static int mvebu_pci_host_probe(struct pci_host_bridge *bridge)
-{
- struct mvebu_pcie *pcie;
- struct pci_bus *bus, *child;
- int ret;
-
- ret = pci_scan_root_bus_bridge(bridge);
- if (ret < 0) {
- dev_err(bridge->dev.parent, "Scanning root bridge failed");
- return ret;
- }
-
- pcie = pci_host_bridge_priv(bridge);
- if (resource_size(&pcie->io) != 0) {
- unsigned int i;
-
- for (i = 0; i < resource_size(&pcie->realio); i += SZ_64K)
- pci_ioremap_io(i, pcie->io.start + i);
- }
-
- bus = bridge->bus;
-
- /*
- * We insert PCI resources into the iomem_resource and
- * ioport_resource trees in either pci_bus_claim_resources()
- * or pci_bus_assign_resources().
- */
- if (pci_has_flag(PCI_PROBE_ONLY)) {
- pci_bus_claim_resources(bus);
- } else {
- pci_bus_size_bridges(bus);
- pci_bus_assign_resources(bus);
-
- list_for_each_entry(child, &bus->children, node)
- pcie_bus_configure_settings(child);
- }
-
- pci_bus_add_devices(bus);
- return 0;
-}
-
static int mvebu_pcie_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
@@ -1112,9 +1243,93 @@ static int mvebu_pcie_probe(struct platform_device *pdev)
continue;
}
+ ret = mvebu_pci_bridge_emul_init(port);
+ if (ret < 0) {
+ dev_err(dev, "%s: cannot init emulated bridge\n",
+ port->name);
+ devm_iounmap(dev, port->base);
+ port->base = NULL;
+ mvebu_pcie_powerdown(port);
+ continue;
+ }
+
+ /*
+ * PCIe topology exported by mvebu hw is quite complicated. In
+ * reality has something like N fully independent host bridges
+ * where each host bridge has one PCIe Root Port (which acts as
+ * PCI Bridge device). Each host bridge has its own independent
+ * internal registers, independent access to PCI config space,
+ * independent interrupt lines, independent window and memory
+ * access configuration. But additionally there is some kind of
+ * peer-to-peer support between PCIe devices behind different
+ * host bridges limited just to forwarding of memory and I/O
+ * transactions (forwarding of error messages and config cycles
+ * is not supported). So we could say there are N independent
+ * PCIe Root Complexes.
+ *
+ * For this kind of setup DT should have been structured into
+ * N independent PCIe controllers / host bridges. But instead
+ * structure in past was defined to put PCIe Root Ports of all
+ * host bridges into one bus zero, like in classic multi-port
+ * Root Complex setup with just one host bridge.
+ *
+ * This means that pci-mvebu.c driver provides "virtual" bus 0
+ * on which registers all PCIe Root Ports (PCI Bridge devices)
+ * specified in DT by their BDF addresses and virtually routes
+ * PCI config access of each PCI bridge device to specific PCIe
+ * host bridge.
+ *
+ * Normally PCI Bridge should choose between Type 0 and Type 1
+ * config requests based on primary and secondary bus numbers
+ * configured on the bridge itself. But because mvebu PCI Bridge
+ * does not have registers for primary and secondary bus numbers
+ * in its config space, it determinates type of config requests
+ * via its own custom way.
+ *
+ * There are two options how mvebu determinate type of config
+ * request.
+ *
+ * 1. If Secondary Bus Number Enable bit is not set or is not
+ * available (applies for pre-XP PCIe controllers) then Type 0
+ * is used if target bus number equals Local Bus Number (bits
+ * [15:8] in register 0x1a04) and target device number differs
+ * from Local Device Number (bits [20:16] in register 0x1a04).
+ * Type 1 is used if target bus number differs from Local Bus
+ * Number. And when target bus number equals Local Bus Number
+ * and target device equals Local Device Number then request is
+ * routed to Local PCI Bridge (PCIe Root Port).
+ *
+ * 2. If Secondary Bus Number Enable bit is set (bit 7 in
+ * register 0x1a2c) then mvebu hw determinate type of config
+ * request like compliant PCI Bridge based on primary bus number
+ * which is configured via Local Bus Number (bits [15:8] in
+ * register 0x1a04) and secondary bus number which is configured
+ * via Secondary Bus Number (bits [7:0] in register 0x1a2c).
+ * Local PCI Bridge (PCIe Root Port) is available on primary bus
+ * as device with Local Device Number (bits [20:16] in register
+ * 0x1a04).
+ *
+ * Secondary Bus Number Enable bit is disabled by default and
+ * option 2. is not available on pre-XP PCIe controllers. Hence
+ * this driver always use option 1.
+ *
+ * Basically it means that primary and secondary buses shares
+ * one virtual number configured via Local Bus Number bits and
+ * Local Device Number bits determinates if accessing primary
+ * or secondary bus. Set Local Device Number to 1 and redirect
+ * all writes of PCI Bridge Secondary Bus Number register to
+ * Local Bus Number (bits [15:8] in register 0x1a04).
+ *
+ * So when accessing devices on buses behind secondary bus
+ * number it would work correctly. And also when accessing
+ * device 0 at secondary bus number via config space would be
+ * correctly routed to secondary bus. Due to issues described
+ * in mvebu_pcie_setup_hw(), PCI Bridges at primary bus (zero)
+ * are not accessed directly via PCI config space but rarher
+ * indirectly via kernel emulated PCI bridge driver.
+ */
mvebu_pcie_setup_hw(port);
- mvebu_pcie_set_local_dev_nr(port, 1);
- mvebu_pci_bridge_emul_init(port);
+ mvebu_pcie_set_local_dev_nr(port, 0);
}
pcie->nports = i;
@@ -1122,8 +1337,55 @@ static int mvebu_pcie_probe(struct platform_device *pdev)
bridge->sysdata = pcie;
bridge->ops = &mvebu_pcie_ops;
bridge->align_resource = mvebu_pcie_align_resource;
+ bridge->map_irq = mvebu_pcie_map_irq;
+
+ return pci_host_probe(bridge);
+}
+
+static int mvebu_pcie_remove(struct platform_device *pdev)
+{
+ struct mvebu_pcie *pcie = platform_get_drvdata(pdev);
+ struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
+ u32 cmd;
+ int i;
+
+ /* Remove PCI bus with all devices. */
+ pci_lock_rescan_remove();
+ pci_stop_root_bus(bridge->bus);
+ pci_remove_root_bus(bridge->bus);
+ pci_unlock_rescan_remove();
+
+ for (i = 0; i < pcie->nports; i++) {
+ struct mvebu_pcie_port *port = &pcie->ports[i];
+
+ if (!port->base)
+ continue;
+
+ /* Disable Root Bridge I/O space, memory space and bus mastering. */
+ cmd = mvebu_readl(port, PCIE_CMD_OFF);
+ cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+ mvebu_writel(port, cmd, PCIE_CMD_OFF);
+
+ /* Mask all interrupt sources. */
+ mvebu_writel(port, 0, PCIE_MASK_OFF);
+
+ /* Free config space for emulated root bridge. */
+ pci_bridge_emul_cleanup(&port->bridge);
- return mvebu_pci_host_probe(bridge);
+ /* Disable and clear BARs and windows. */
+ mvebu_pcie_disable_wins(port);
+
+ /* Delete PCIe IO and MEM windows. */
+ if (port->iowin.size)
+ mvebu_pcie_del_windows(port, port->iowin.base, port->iowin.size);
+ if (port->memwin.size)
+ mvebu_pcie_del_windows(port, port->memwin.base, port->memwin.size);
+
+ /* Power down card and disable clocks. Must be the last step. */
+ mvebu_pcie_powerdown(port);
+ }
+
+ return 0;
}
static const struct of_device_id mvebu_pcie_of_match_table[] = {
@@ -1142,10 +1404,14 @@ static struct platform_driver mvebu_pcie_driver = {
.driver = {
.name = "mvebu-pcie",
.of_match_table = mvebu_pcie_of_match_table,
- /* driver unloading/unbinding currently not supported */
- .suppress_bind_attrs = true,
.pm = &mvebu_pcie_pm_ops,
},
.probe = mvebu_pcie_probe,
+ .remove = mvebu_pcie_remove,
};
-builtin_platform_driver(mvebu_pcie_driver);
+module_platform_driver(mvebu_pcie_driver);
+
+MODULE_AUTHOR("Thomas Petazzoni <thomas.petazzoni@bootlin.com>");
+MODULE_AUTHOR("Pali Rohár <pali@kernel.org>");
+MODULE_DESCRIPTION("Marvell EBU PCIe controller");
+MODULE_LICENSE("GPL v2");