| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
AMD does not have the requirement for a synchronization barrier when
acccessing a certain group of MSRs. Do not incur that unnecessary
penalty there.
There will be a CPUID bit which explicitly states that a MFENCE is not
needed. Once that bit is added to the APM, this will be extended with
it.
While at it, move to processor.h to avoid include hell. Untangling that
file properly is a matter for another day.
Some notes on the performance aspect of why this is relevant, courtesy
of Kishon VijayAbraham <Kishon.VijayAbraham@amd.com>:
On a AMD Zen4 system with 96 cores, a modified ipi-bench[1] on a VM
shows x2AVIC IPI rate is 3% to 4% lower than AVIC IPI rate. The
ipi-bench is modified so that the IPIs are sent between two vCPUs in the
same CCX. This also requires to pin the vCPU to a physical core to
prevent any latencies. This simulates the use case of pinning vCPUs to
the thread of a single CCX to avoid interrupt IPI latency.
In order to avoid run-to-run variance (for both x2AVIC and AVIC), the
below configurations are done:
1) Disable Power States in BIOS (to prevent the system from going to
lower power state)
2) Run the system at fixed frequency 2500MHz (to prevent the system
from increasing the frequency when the load is more)
With the above configuration:
*) Performance measured using ipi-bench for AVIC:
Average Latency: 1124.98ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 42.6759M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
*) Performance measured using ipi-bench for x2AVIC:
Average Latency: 1172.42ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 40.9432M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
From above, x2AVIC latency is ~4% more than AVIC. However, the expectation is
x2AVIC performance to be better or equivalent to AVIC. Upon analyzing
the perf captures, it is observed significant time is spent in
weak_wrmsr_fence() invoked by x2apic_send_IPI().
With the fix to skip weak_wrmsr_fence()
*) Performance measured using ipi-bench for x2AVIC:
Average Latency: 1117.44ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 42.9608M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
Comparing the performance of x2AVIC with and without the fix, it can be seen
the performance improves by ~4%.
Performance captured using an unmodified ipi-bench using the 'mesh-ipi' option
with and without weak_wrmsr_fence() on a Zen4 system also showed significant
performance improvement without weak_wrmsr_fence(). The 'mesh-ipi' option ignores
CCX or CCD and just picks random vCPU.
Average throughput (10 iterations) with weak_wrmsr_fence(),
Cumulative throughput: 4933374 IPI/s
Average throughput (10 iterations) without weak_wrmsr_fence(),
Cumulative throughput: 6355156 IPI/s
[1] https://github.com/bytedance/kvm-utils/tree/master/microbenchmark/ipi-bench
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230622095212.20940-1-bp@alien8.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Thomas Gleixner:
- Limit the hardcoded topology quirk for Hygon CPUs to those which have
a model ID less than 4.
The newer models have the topology CPUID leaf 0xB correctly
implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By
chance a XEN/PV boot ends up with smp_num_siblings == 2, which makes
the hotplug control stay at its default value "enabled". So the mask
is never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core
to deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or
even non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned
long or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die IDs.
That's really not the right place simply because cpuinfo is subject
to be reinitialized when a CPU goes through an offline/online cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
* tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/apic, x86/hyperv: Use u32 in hv_snp_boot_ap() too
x86/cpu: Provide debug interface
x86/cpu/topology: Cure the abuse of cpuinfo for persisting logical ids
x86/apic: Use u32 for wakeup_secondary_cpu[_64]()
x86/apic: Use u32 for [gs]et_apic_id()
x86/apic: Use u32 for phys_pkg_id()
x86/apic: Use u32 for cpu_present_to_apicid()
x86/apic: Use u32 for check_apicid_used()
x86/apic: Use u32 for APIC IDs in global data
x86/apic: Use BAD_APICID consistently
x86/cpu: Move cpu_l[l2]c_id into topology info
x86/cpu: Move logical package and die IDs into topology info
x86/cpu: Remove pointless evaluation of x86_coreid_bits
x86/cpu: Move cu_id into topology info
x86/cpu: Move cpu_core_id into topology info
hwmon: (fam15h_power) Use topology_core_id()
scsi: lpfc: Use topology_core_id()
x86/cpu: Move cpu_die_id into topology info
x86/cpu: Move phys_proc_id into topology info
x86/cpu: Encapsulate topology information in cpuinfo_x86
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm handling updates from Ingo Molnar:
- Add new NX-stack self-test
- Improve NUMA partial-CFMWS handling
- Fix #VC handler bugs resulting in SEV-SNP boot failures
- Drop the 4MB memory size restriction on minimal NUMA nodes
- Reorganize headers a bit, in preparation to header dependency
reduction efforts
- Misc cleanups & fixes
* tag 'x86-mm-2023-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Drop the 4 MB restriction on minimal NUMA node memory size
selftests/x86/lam: Zero out buffer for readlink()
x86/sev: Drop unneeded #include
x86/sev: Move sev_setup_arch() to mem_encrypt.c
x86/tdx: Replace deprecated strncpy() with strtomem_pad()
selftests/x86/mm: Add new test that userspace stack is in fact NX
x86/sev: Make boot_ghcb_page[] static
x86/boot: Move x86_cache_alignment initialization to correct spot
x86/sev-es: Set x86_virt_bits to the correct value straight away, instead of a two-phase approach
x86/sev-es: Allow copy_from_kernel_nofault() in earlier boot
x86_64: Show CR4.PSE on auxiliaries like on BSP
x86/iommu/docs: Update AMD IOMMU specification document URL
x86/sev/docs: Update document URL in amd-memory-encryption.rst
x86/mm: Move arch_memory_failure() and arch_is_platform_page() definitions from <asm/processor.h> to <asm/pgtable.h>
ACPI/NUMA: Apply SRAT proximity domain to entire CFMWS window
x86/numa: Introduce numa_fill_memblks()
|
|
APIC IDs are used with random data types u16, u32, int, unsigned int,
unsigned long.
Make it all consistently use u32 because that reflects the hardware
register width and fixup the most obvious usage sites of that.
The APIC callbacks will be addressed separately.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.922905727@linutronix.de
|
|
The topology IDs which identify the LLC and L2 domains clearly belong to
the per CPU topology information.
Move them into cpuinfo_x86::cpuinfo_topo and get rid of the extra per CPU
data and the related exports.
This also paves the way to do proper topology evaluation during early boot
because it removes the only per CPU dependency for that.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.803864641@linutronix.de
|
|
Yet another topology related data pair. Rename logical_proc_id to
logical_pkg_id so it fits the common naming conventions.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.745139505@linutronix.de
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.628405546@linutronix.de
|
|
Rename it to core_id and stick it to the other ID fields.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.566519388@linutronix.de
|
|
Move the next member.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.388185134@linutronix.de
|
|
Rename it to pkg_id which is the terminology used in the kernel.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.329006989@linutronix.de
|
|
The topology related information is randomly scattered across cpuinfo_x86.
Create a new structure cpuinfo_topo and move in a first step initial_apicid
and apicid into it.
Aside of being better readable this is in preparation for replacing the
horribly fragile CPU topology evaluation code further down the road.
Consolidate APIC ID fields to u32 as that represents the hardware type.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20230814085112.269787744@linutronix.de
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
from <asm/processor.h> to <asm/pgtable.h>
<linux/mm.h> relies on these definitions being included first,
which is true currently due to historic header spaghetti,
but in the future <asm/processor.h> will not guaranteed to be
included by the MM code.
Move these definitions over into a suitable MM header.
This is a preparatory patch for x86 header dependency simplifications
and reductions.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
|
|
Booting with mitigations=off incorrectly prevents the
X86_FEATURE_{IBPB_BRTYPE,SBPB} CPUID bits from getting set.
Also, future CPUs without X86_BUG_SRSO might still have IBPB with branch
type prediction flushing, in which case SBPB should be used instead of
IBPB. The current code doesn't allow for that.
Also, cpu_has_ibpb_brtype_microcode() has some surprising side effects
and the setting of these feature bits really doesn't belong in the
mitigation code anyway. Move it to earlier.
Fixes: fb3bd914b3ec ("x86/srso: Add a Speculative RAS Overflow mitigation")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Nikolay Borisov <nik.borisov@suse.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/869a1709abfe13b673bdd10c2f4332ca253a40bc.1693889988.git.jpoimboe@kernel.org
|
|
The SYSCALL instruction cannot really be disabled in compatibility mode.
The best that can be done is to configure the CSTAR msr to point to a
minimal handler. Currently this handler has a rather misleading name -
ignore_sysret() as it's not really doing anything with sysret.
Give it a more descriptive name.
Signed-off-by: Nikolay Borisov <nik.borisov@suse.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20230623111409.3047467-3-nik.borisov@suse.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 shadow stack support from Dave Hansen:
"This is the long awaited x86 shadow stack support, part of Intel's
Control-flow Enforcement Technology (CET).
CET consists of two related security features: shadow stacks and
indirect branch tracking. This series implements just the shadow stack
part of this feature, and just for userspace.
The main use case for shadow stack is providing protection against
return oriented programming attacks. It works by maintaining a
secondary (shadow) stack using a special memory type that has
protections against modification. When executing a CALL instruction,
the processor pushes the return address to both the normal stack and
to the special permission shadow stack. Upon RET, the processor pops
the shadow stack copy and compares it to the normal stack copy.
For more information, refer to the links below for the earlier
versions of this patch set"
Link: https://lore.kernel.org/lkml/20220130211838.8382-1-rick.p.edgecombe@intel.com/
Link: https://lore.kernel.org/lkml/20230613001108.3040476-1-rick.p.edgecombe@intel.com/
* tag 'x86_shstk_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
x86/shstk: Change order of __user in type
x86/ibt: Convert IBT selftest to asm
x86/shstk: Don't retry vm_munmap() on -EINTR
x86/kbuild: Fix Documentation/ reference
x86/shstk: Move arch detail comment out of core mm
x86/shstk: Add ARCH_SHSTK_STATUS
x86/shstk: Add ARCH_SHSTK_UNLOCK
x86: Add PTRACE interface for shadow stack
selftests/x86: Add shadow stack test
x86/cpufeatures: Enable CET CR4 bit for shadow stack
x86/shstk: Wire in shadow stack interface
x86: Expose thread features in /proc/$PID/status
x86/shstk: Support WRSS for userspace
x86/shstk: Introduce map_shadow_stack syscall
x86/shstk: Check that signal frame is shadow stack mem
x86/shstk: Check that SSP is aligned on sigreturn
x86/shstk: Handle signals for shadow stack
x86/shstk: Introduce routines modifying shstk
x86/shstk: Handle thread shadow stack
x86/shstk: Add user-mode shadow stack support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Dave Hansen:
"This includes a very thorough rework of the 'struct apic' handlers.
Quite a variety of them popped up over the years, especially in the
32-bit days when odd apics were much more in vogue.
The end result speaks for itself, which is a removal of a ton of code
and static calls to replace indirect calls.
If there's any breakage here, it's likely to be around the 32-bit
museum pieces that get light to no testing these days.
Summary:
- Rework apic callbacks, getting rid of unnecessary ones and
coalescing lots of silly duplicates.
- Use static_calls() instead of indirect calls for apic->foo()
- Tons of cleanups an crap removal along the way"
* tag 'x86_apic_for_6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
x86/apic: Turn on static calls
x86/apic: Provide static call infrastructure for APIC callbacks
x86/apic: Wrap IPI calls into helper functions
x86/apic: Mark all hotpath APIC callback wrappers __always_inline
x86/xen/apic: Mark apic __ro_after_init
x86/apic: Convert other overrides to apic_update_callback()
x86/apic: Replace acpi_wake_cpu_handler_update() and apic_set_eoi_cb()
x86/apic: Provide apic_update_callback()
x86/xen/apic: Use standard apic driver mechanism for Xen PV
x86/apic: Provide common init infrastructure
x86/apic: Wrap apic->native_eoi() into a helper
x86/apic: Nuke ack_APIC_irq()
x86/apic: Remove pointless arguments from [native_]eoi_write()
x86/apic/noop: Tidy up the code
x86/apic: Remove pointless NULL initializations
x86/apic: Sanitize APIC ID range validation
x86/apic: Prepare x2APIC for using apic::max_apic_id
x86/apic: Simplify X2APIC ID validation
x86/apic: Add max_apic_id member
x86/apic: Wrap APIC ID validation into an inline
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 cleanups from Ingo Molnar:
"The following commit deserves special mention:
22dc02f81cddd Revert "sched/fair: Move unused stub functions to header"
This is in x86/cleanups, because the revert is a re-application of a
number of cleanups that got removed inadvertedly"
[ This also effectively undoes the amd_check_microcode() microcode
declaration change I had done in my microcode loader merge in commit
42a7f6e3ffe0 ("Merge tag 'x86_microcode_for_v6.6_rc1' [...]").
I picked the declaration change by Arnd from this branch instead,
which put it in <asm/processor.h> instead of <asm/microcode.h> like I
had done in my merge resolution - Linus ]
* tag 'x86-cleanups-2023-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/uv: Refactor code using deprecated strncpy() interface to use strscpy()
x86/hpet: Refactor code using deprecated strncpy() interface to use strscpy()
x86/platform/uv: Refactor code using deprecated strcpy()/strncpy() interfaces to use strscpy()
x86/qspinlock-paravirt: Fix missing-prototype warning
x86/paravirt: Silence unused native_pv_lock_init() function warning
x86/alternative: Add a __alt_reloc_selftest() prototype
x86/purgatory: Include header for warn() declaration
x86/asm: Avoid unneeded __div64_32 function definition
Revert "sched/fair: Move unused stub functions to header"
x86/apic: Hide unused safe_smp_processor_id() on 32-bit UP
x86/cpu: Fix amd_check_microcode() declaration
|
|
The only remaining consumer is new_inode, where it showed up in 2001 as
commit c37fa164f793 ("v2.4.9.9 -> v2.4.9.10") in a historical repo [1]
with a changelog which does not mention it.
Since then the line got only touched up to keep compiling.
While it may have been of benefit back in the day, it is guaranteed to
at best not get in the way in the multicore setting -- as the code
performs *a lot* of work between the prefetch and actual lock acquire,
any contention means the cacheline is already invalid by the time the
routine calls spin_lock(). It adds spurious traffic, for short.
On top of it prefetch is notoriously tricky to use for single-threaded
purposes, making it questionable from the get go.
As such, remove it.
I admit upfront I did not see value in benchmarking this change, but I
can do it if that is deemed appropriate.
Removal from new_inode and of the entire thing are in the same patch as
requested by Linus, so whatever weird looks can be directed at that guy.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/fs/inode.c?id=c37fa164f793735b32aa3f53154ff1a7659e6442 [1]
Signed-off-by: Mateusz Guzik <mjguzik@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The declaration got placed in the .c file of the caller, but that
causes a warning for the definition:
arch/x86/kernel/cpu/bugs.c:682:6: error: no previous prototype for 'gds_ucode_mitigated' [-Werror=missing-prototypes]
Move it to a header where both sides can observe it instead.
Fixes: 81ac7e5d74174 ("KVM: Add GDS_NO support to KVM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/all/20230809130530.1913368-2-arnd%40kernel.org
|
|
It's not longer used outside the source file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Juergen Gross <jgross@suse.com> # Xen PV (dom0 and unpriv. guest)
|
|
Under certain circumstances, an integer division by 0 which faults, can
leave stale quotient data from a previous division operation on Zen1
microarchitectures.
Do a dummy division 0/1 before returning from the #DE exception handler
in order to avoid any leaks of potentially sensitive data.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce basic shadow stack enabling/disabling/allocation routines.
A task's shadow stack is allocated from memory with VM_SHADOW_STACK flag
and has a fixed size of min(RLIMIT_STACK, 4GB).
Keep the task's shadow stack address and size in thread_struct. This will
be copied when cloning new threads, but needs to be cleared during exec,
so add a function to do this.
32 bit shadow stack is not expected to have many users and it will
complicate the signal implementation. So do not support IA32 emulation
or x32.
Co-developed-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Yu-cheng Yu <yu-cheng.yu@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: John Allen <john.allen@amd.com>
Tested-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/all/20230613001108.3040476-29-rick.p.edgecombe%40intel.com
|
|
Add three new arch_prctl() handles:
- ARCH_SHSTK_ENABLE/DISABLE enables or disables the specified
feature. Returns 0 on success or a negative value on error.
- ARCH_SHSTK_LOCK prevents future disabling or enabling of the
specified feature. Returns 0 on success or a negative value
on error.
The features are handled per-thread and inherited over fork(2)/clone(2),
but reset on exec().
Co-developed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mike Rapoport (IBM) <rppt@kernel.org>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: John Allen <john.allen@amd.com>
Tested-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/all/20230613001108.3040476-27-rick.p.edgecombe%40intel.com
|
|
The newly added amd_check_microcode() function has two conflicting definitions
if CONFIG_CPU_SUP_AMD is enabled and CONFIG_MICROCODE_AMD is disabled. Since
the header with the stub definition is not included in cpu/amd.c, this only
causes a -Wmissing-prototype warning with W=1:
arch/x86/kernel/cpu/amd.c:1289:6: error: no previous prototype for 'amd_check_microcode' [-Werror=missing-prototypes]
Adding the missing #include shows the other problem:
arch/x86/kernel/cpu/amd.c:1290:6: error: redefinition of 'amd_check_microcode'
arch/x86/include/asm/microcode_amd.h:58:20: note: previous definition of 'amd_check_microcode' with type 'void(void)'
Move the declaration into a more appropriate header that is already
included, with the #ifdef check changed to match the definition's.
Fixes: 522b1d69219d8 ("x86/cpu/amd: Add a Zenbleed fix")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230725121751.2007665-1-arnd@kernel.org
|
|
Add a mitigation for the speculative return address stack overflow
vulnerability found on AMD processors.
The mitigation works by ensuring all RET instructions speculate to
a controlled location, similar to how speculation is controlled in the
retpoline sequence. To accomplish this, the __x86_return_thunk forces
the CPU to mispredict every function return using a 'safe return'
sequence.
To ensure the safety of this mitigation, the kernel must ensure that the
safe return sequence is itself free from attacker interference. In Zen3
and Zen4, this is accomplished by creating a BTB alias between the
untraining function srso_untrain_ret_alias() and the safe return
function srso_safe_ret_alias() which results in evicting a potentially
poisoned BTB entry and using that safe one for all function returns.
In older Zen1 and Zen2, this is accomplished using a reinterpretation
technique similar to Retbleed one: srso_untrain_ret() and
srso_safe_ret().
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
|
|
The synchronization of the AP with the control CPU is a SMP boot problem
and has nothing to do with cpu_init().
Open code cpu_init_secondary() in start_secondary() and move
wait_for_master_cpu() into the SMP boot code.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/20230512205255.981999763@linutronix.de
|
|
In order to facilitate parallel startup, start to eliminate some of the
global variables passing information to CPUs in the startup path.
However, start by introducing one more: smpboot_control. For now this
merely holds the CPU# of the CPU which is coming up. Each CPU can then
find its own per-cpu data, and everything else it needs can be found
from there, allowing the other global variables to be removed.
First to be removed is initial_stack. Each CPU can load %rsp from its
current_task->thread.sp instead. That is already set up with the correct
idle thread for APs. Set up the .sp field in INIT_THREAD on x86 so that
the BSP also finds a suitable stack pointer in the static per-cpu data
when coming up on first boot.
On resume from S3, the CPU needs a temporary stack because its idle task
is already active. Instead of setting initial_stack, the sleep code can
simply set its own current->thread.sp to point to the temporary stack.
Nobody else cares about ->thread.sp for a thread which is currently on
a CPU, because the true value is actually in the %rsp register. Which
is restored with the rest of the CPU context in do_suspend_lowlevel().
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Usama Arif <usama.arif@bytedance.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Usama Arif <usama.arif@bytedance.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20230316222109.1940300-7-usama.arif@bytedance.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso updates from Borislav Petkov:
- Add getcpu support for the 32-bit version of the vDSO
- Some smaller fixes
* tag 'x86_vdso_for_v6.3_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix -Wmissing-prototypes warnings
x86/vdso: Fake 32bit VDSO build on 64bit compile for vgetcpu
selftests: Emit a warning if getcpu() is missing on 32bit
x86/vdso: Provide getcpu for x86-32.
x86/cpu: Provide the full setup for getcpu() on x86-32
x86/vdso: Move VDSO image init to vdso2c generated code
|
|
Generate an init function for each VDSO image, replacing init_vdso() and
sysenter_setup().
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230124184019.26850-1-brgerst@gmail.com
|
|
The kernel caches each CPU's feature bits at boot in an x86_capability[]
structure. However, the capabilities in the BSP's copy can be turned off
as a result of certain command line parameters or configuration
restrictions, for example the SGX bit. This can cause a mismatch when
comparing the values before and after the microcode update.
Another example is X86_FEATURE_SRBDS_CTRL which gets added only after
microcode update:
--- cpuid.before 2023-01-21 14:54:15.652000747 +0100
+++ cpuid.after 2023-01-21 14:54:26.632001024 +0100
@@ -10,7 +10,7 @@ CPU:
0x00000004 0x04: eax=0x00000000 ebx=0x00000000 ecx=0x00000000 edx=0x00000000
0x00000005 0x00: eax=0x00000040 ebx=0x00000040 ecx=0x00000003 edx=0x11142120
0x00000006 0x00: eax=0x000027f7 ebx=0x00000002 ecx=0x00000001 edx=0x00000000
- 0x00000007 0x00: eax=0x00000000 ebx=0x029c6fbf ecx=0x40000000 edx=0xbc002400
+ 0x00000007 0x00: eax=0x00000000 ebx=0x029c6fbf ecx=0x40000000 edx=0xbc002e00
^^^
and which proves for a gazillionth time that late loading is a bad bad
idea.
microcode_check() is called after an update to report any previously
cached CPUID bits which might have changed due to the update.
Therefore, store the cached CPU caps before the update and compare them
with the CPU caps after the microcode update has succeeded.
Thus, the comparison is done between the CPUID *hardware* bits before
and after the upgrade instead of using the cached, possibly runtime
modified values in BSP's boot_cpu_data copy.
As a result, false warnings about CPUID bits changes are avoided.
[ bp:
- Massage.
- Add SRBDS_CTRL example.
- Add kernel-doc.
- Incorporate forgotten review feedback from dhansen.
]
Fixes: 1008c52c09dc ("x86/CPU: Add a microcode loader callback")
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230109153555.4986-3-ashok.raj@intel.com
|
|
Add a parameter to store CPU capabilities before performing a microcode
update so that CPU capabilities can be compared before and after update.
[ bp: Massage. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230109153555.4986-2-ashok.raj@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Borislav Petkov:
- Add the call depth tracking mitigation for Retbleed which has been
long in the making. It is a lighterweight software-only fix for
Skylake-based cores where enabling IBRS is a big hammer and causes a
significant performance impact.
What it basically does is, it aligns all kernel functions to 16 bytes
boundary and adds a 16-byte padding before the function, objtool
collects all functions' locations and when the mitigation gets
applied, it patches a call accounting thunk which is used to track
the call depth of the stack at any time.
When that call depth reaches a magical, microarchitecture-specific
value for the Return Stack Buffer, the code stuffs that RSB and
avoids its underflow which could otherwise lead to the Intel variant
of Retbleed.
This software-only solution brings a lot of the lost performance
back, as benchmarks suggest:
https://lore.kernel.org/all/20220915111039.092790446@infradead.org/
That page above also contains a lot more detailed explanation of the
whole mechanism
- Implement a new control flow integrity scheme called FineIBT which is
based on the software kCFI implementation and uses hardware IBT
support where present to annotate and track indirect branches using a
hash to validate them
- Other misc fixes and cleanups
* tag 'x86_core_for_v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
x86/paravirt: Use common macro for creating simple asm paravirt functions
x86/paravirt: Remove clobber bitmask from .parainstructions
x86/debug: Include percpu.h in debugreg.h to get DECLARE_PER_CPU() et al
x86/cpufeatures: Move X86_FEATURE_CALL_DEPTH from bit 18 to bit 19 of word 11, to leave space for WIP X86_FEATURE_SGX_EDECCSSA bit
x86/Kconfig: Enable kernel IBT by default
x86,pm: Force out-of-line memcpy()
objtool: Fix weak hole vs prefix symbol
objtool: Optimize elf_dirty_reloc_sym()
x86/cfi: Add boot time hash randomization
x86/cfi: Boot time selection of CFI scheme
x86/ibt: Implement FineIBT
objtool: Add --cfi to generate the .cfi_sites section
x86: Add prefix symbols for function padding
objtool: Add option to generate prefix symbols
objtool: Avoid O(bloody terrible) behaviour -- an ode to libelf
objtool: Slice up elf_create_section_symbol()
kallsyms: Revert "Take callthunks into account"
x86: Unconfuse CONFIG_ and X86_FEATURE_ namespaces
x86/retpoline: Fix crash printing warning
x86/paravirt: Fix a !PARAVIRT build warning
...
|
|
Carve it out into a special header, where it belongs.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20221124164150.3040-1-bp@alien8.de
|
|
Further extend struct pcpu_hot with the hard and soft irq stack
pointers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220915111145.599170752@infradead.org
|
|
Extend the struct pcpu_hot cacheline with current_top_of_stack;
another very frequently used value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220915111145.493038635@infradead.org
|
|
The only place where switch_to_new_gdt() is required is early boot to
switch from the early GDT to the direct GDT. Any other invocation is
completely redundant because it does not change anything.
Secondary CPUs come out of the ASM code with GDT and GSBASE correctly set
up. The same is true for XEN_PV.
Remove all the voodoo invocations which are left overs from the ancient
past, rename the function to switch_gdt_and_percpu_base() and mark it init.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220915111143.198076128@infradead.org
|
|
On 32bit FS and on 64bit GS segments are already set up correctly, but
load_percpu_segment() still sets [FG]S after switching from the early GDT
to the direct GDT.
For 32bit the segment load has no side effects, but on 64bit it causes
GSBASE to become 0, which means that any per CPU access before GSBASE is
set to the new value is going to fault. That's the reason why the whole
file containing this code has stackprotector removed.
But that's a pointless exercise for both 32 and 64 bit as the relevant
segment selector is already correct. Loading the new GDT does not change
that.
Remove the segment loads and add comments.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220915111143.097052006@infradead.org
|
|
Only x86 has own release_thread(), introduce a new weak release_thread()
function to clean empty definitions in other ARCHs.
Link: https://lkml.kernel.org/r/20220819014406.32266-1-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Guo Ren <guoren@kernel.org> [csky]
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Brian Cain <bcain@quicinc.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Stafford Horne <shorne@gmail.com> [openrisc]
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Acked-by: Huacai Chen <chenhuacai@kernel.org> [LoongArch]
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Chris Zankel <chris@zankel.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Guo Ren <guoren@kernel.org> [csky]
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Xuerui Wang <kernel@xen0n.name>
Cc: Yoshinori Sato <ysato@users.osdn.me>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Becaues GCC clearly lost it's marbles again...
vmlinux.o: warning: objtool: enter_from_user_mode+0x4e: call to on_thread_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode+0x53: call to on_thread_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode_prepare+0x4e: call to on_thread_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: irqentry_enter_from_user_mode+0x4e: call to on_thread_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: enter_from_user_mode+0x4e: call to current_top_of_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode+0x53: call to current_top_of_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode_prepare+0x4e: call to current_top_of_stack() leaves .noinstr.text section
vmlinux.o: warning: objtool: irqentry_enter_from_user_mode+0x4e: call to current_top_of_stack() leaves .noinstr.text section
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220526105958.071435483@infradead.org
|
|
Conflicts:
arch/x86/include/asm/cpufeatures.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
vmlinux.o: warning: objtool: smp_stop_nmi_callback()+0x2b: unreachable instruction
0000 0000000000047cf0 <smp_stop_nmi_callback>:
...
0026 47d16: e8 00 00 00 00 call 47d1b <smp_stop_nmi_callback+0x2b> 47d17: R_X86_64_PLT32 stop_this_cpu-0x4
002b 47d1b: b8 01 00 00 00 mov $0x1,%eax
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154319.290905453@infradead.org
|
|
Currently, the PPIN (Protected Processor Inventory Number) MSR is read
by every CPU that processes a machine check, CMCI, or just polls machine
check banks from a periodic timer. This is not a "fast" MSR, so this
adds to overhead of processing errors.
Add a new "ppin" field to the cpuinfo_x86 structure. Read and save the
PPIN during initialization. Use this copy in mce_setup() instead of
reading the MSR.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20220131230111.2004669-4-tony.luck@intel.com
|
|
Add a call inside memory_failure() to call the arch specific code
to check if the address is an SGX EPC page and handle it.
Note the SGX EPC pages do not have a "struct page" entry, so the hook
goes in at the same point as the device mapping hook.
Pull the call to acquire the mutex earlier so the SGX errors are also
protected.
Make set_mce_nospec() skip SGX pages when trying to adjust
the 1:1 map.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Link: https://lkml.kernel.org/r/20211026220050.697075-6-tony.luck@intel.com
|
|
* Fix misuse of gfn-to-pfn cache when recording guest steal time / preempted status
* Fix selftests on APICv machines
* Fix sparse warnings
* Fix detection of KVM features in CPUID
* Cleanups for bogus writes to MSR_KVM_PV_EOI_EN
* Fixes and cleanups for MSR bitmap handling
* Cleanups for INVPCID
* Make x86 KVM_SOFT_MAX_VCPUS consistent with other architectures
|
|
Currently when kvm_update_cpuid_runtime() runs, it assumes that the
KVM_CPUID_FEATURES leaf is located at 0x40000001. This is not true,
however, if Hyper-V support is enabled. In this case the KVM leaves will
be offset.
This patch introdues as new 'kvm_cpuid_base' field into struct
kvm_vcpu_arch to track the location of the KVM leaves and function
kvm_update_kvm_cpuid_base() (called from kvm_set_cpuid()) to locate the
leaves using the 'KVMKVMKVM\0\0\0' signature (which is now given a
definition in kvm_para.h). Adjustment of KVM_CPUID_FEATURES will hence now
target the correct leaf.
NOTE: A new for_each_possible_hypervisor_cpuid_base() macro is intoduced
into processor.h to avoid having duplicate code for the iteration
over possible hypervisor base leaves.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Message-Id: <20211105095101.5384-3-pdurrant@amazon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Borislav Petkov:
- Do not #GP on userspace use of CLI/STI but pretend it was a NOP to
keep old userspace from breaking. Adjust the corresponding iopl
selftest to that.
- Improve stack overflow warnings to say which stack got overflowed and
raise the exception stack sizes to 2 pages since overflowing the
single page of exception stack is very easy to do nowadays with all
the tracing machinery enabled. With that, rip out the custom mapping
of AMD SEV's too.
- A bunch of changes in preparation for FGKASLR like supporting more
than 64K section headers in the relocs tool, correct ORC lookup table
size to cover the whole kernel .text and other adjustments.
* tag 'x86_core_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/x86/iopl: Adjust to the faked iopl CLI/STI usage
vmlinux.lds.h: Have ORC lookup cover entire _etext - _stext
x86/boot/compressed: Avoid duplicate malloc() implementations
x86/boot: Allow a "silent" kaslr random byte fetch
x86/tools/relocs: Support >64K section headers
x86/sev: Make the #VC exception stacks part of the default stacks storage
x86: Increase exception stack sizes
x86/mm/64: Improve stack overflow warnings
x86/iopl: Fake iopl(3) CLI/STI usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cpu updates from Borislav Petkov:
- Start checking a CPUID bit on AMD Zen3 which states that the CPU
clears the segment base when a null selector is written. Do the
explicit detection on older CPUs, zen2 and hygon specifically, which
have the functionality but do not advertize the CPUID bit. Factor in
the presence of a hypervisor underneath the kernel and avoid doing
the explicit check there which the HV might've decided to not
advertize for migration safety reasons, or similar.
- Add support for a new X86 CPU vendor: VORTEX. Needed for whitelisting
those CPUs in the hardware vulnerabilities detection
- Force the compiler to use rIP-relative addressing in the fallback
path of static_cpu_has(), in order to avoid unnecessary register
pressure
* tag 'x86_cpu_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Fix migration safety with X86_BUG_NULL_SEL
x86/CPU: Add support for Vortex CPUs
x86/umip: Downgrade warning messages to debug loglevel
x86/asm: Avoid adding register pressure for the init case in static_cpu_has()
x86/asm: Add _ASM_RIP() macro for x86-64 (%rip) suffix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu updates from Thomas Gleixner:
- Cleanup of extable fixup handling to be more robust, which in turn
allows to make the FPU exception fixups more robust as well.
- Change the return code for signal frame related failures from
explicit error codes to a boolean fail/success as that's all what the
calling code evaluates.
- A large refactoring of the FPU code to prepare for adding AMX
support:
- Distangle the public header maze and remove especially the
misnomed kitchen sink internal.h which is despite it's name
included all over the place.
- Add a proper abstraction for the register buffer storage (struct
fpstate) which allows to dynamically size the buffer at runtime
by flipping the pointer to the buffer container from the default
container which is embedded in task_struct::tread::fpu to a
dynamically allocated container with a larger register buffer.
- Convert the code over to the new fpstate mechanism.
- Consolidate the KVM FPU handling by moving the FPU related code
into the FPU core which removes the number of exports and avoids
adding even more export when AMX has to be supported in KVM.
This also removes duplicated code which was of course
unnecessary different and incomplete in the KVM copy.
- Simplify the KVM FPU buffer handling by utilizing the new
fpstate container and just switching the buffer pointer from the
user space buffer to the KVM guest buffer when entering
vcpu_run() and flipping it back when leaving the function. This
cuts the memory requirements of a vCPU for FPU buffers in half
and avoids pointless memory copy operations.
This also solves the so far unresolved problem of adding AMX
support because the current FPU buffer handling of KVM inflicted
a circular dependency between adding AMX support to the core and
to KVM. With the new scheme of switching fpstate AMX support can
be added to the core code without affecting KVM.
- Replace various variables with proper data structures so the
extra information required for adding dynamically enabled FPU
features (AMX) can be added in one place
- Add AMX (Advanced Matrix eXtensions) support (finally):
AMX is a large XSTATE component which is going to be available with
Saphire Rapids XEON CPUs. The feature comes with an extra MSR
(MSR_XFD) which allows to trap the (first) use of an AMX related
instruction, which has two benefits:
1) It allows the kernel to control access to the feature
2) It allows the kernel to dynamically allocate the large register
state buffer instead of burdening every task with the the extra
8K or larger state storage.
It would have been great to gain this kind of control already with
AVX512.
The support comes with the following infrastructure components:
1) arch_prctl() to
- read the supported features (equivalent to XGETBV(0))
- read the permitted features for a task
- request permission for a dynamically enabled feature
Permission is granted per process, inherited on fork() and
cleared on exec(). The permission policy of the kernel is
restricted to sigaltstack size validation, but the syscall
obviously allows further restrictions via seccomp etc.
2) A stronger sigaltstack size validation for sys_sigaltstack(2)
which takes granted permissions and the potentially resulting
larger signal frame into account. This mechanism can also be used
to enforce factual sigaltstack validation independent of dynamic
features to help with finding potential victims of the 2K
sigaltstack size constant which is broken since AVX512 support
was added.
3) Exception handling for #NM traps to catch first use of a extended
feature via a new cause MSR. If the exception was caused by the
use of such a feature, the handler checks permission for that
feature. If permission has not been granted, the handler sends a
SIGILL like the #UD handler would do if the feature would have
been disabled in XCR0. If permission has been granted, then a new
fpstate which fits the larger buffer requirement is allocated.
In the unlikely case that this allocation fails, the handler
sends SIGSEGV to the task. That's not elegant, but unavoidable as
the other discussed options of preallocation or full per task
permissions come with their own set of horrors for kernel and/or
userspace. So this is the lesser of the evils and SIGSEGV caused
by unexpected memory allocation failures is not a fundamentally
new concept either.
When allocation succeeds, the fpstate properties are filled in to
reflect the extended feature set and the resulting sizes, the
fpu::fpstate pointer is updated accordingly and the trap is
disarmed for this task permanently.
4) Enumeration and size calculations
5) Trap switching via MSR_XFD
The XFD (eXtended Feature Disable) MSR is context switched with
the same life time rules as the FPU register state itself. The
mechanism is keyed off with a static key which is default
disabled so !AMX equipped CPUs have zero overhead. On AMX enabled
CPUs the overhead is limited by comparing the tasks XFD value
with a per CPU shadow variable to avoid redundant MSR writes. In
case of switching from a AMX using task to a non AMX using task
or vice versa, the extra MSR write is obviously inevitable.
All other places which need to be aware of the variable feature
sets and resulting variable sizes are not affected at all because
they retrieve the information (feature set, sizes) unconditonally
from the fpstate properties.
6) Enable the new AMX states
Note, this is relatively new code despite the fact that AMX support
is in the works for more than a year now.
The big refactoring of the FPU code, which allowed to do a proper
integration has been started exactly 3 weeks ago. Refactoring of the
existing FPU code and of the original AMX patches took a week and has
been subject to extensive review and testing. The only fallout which
has not been caught in review and testing right away was restricted
to AMX enabled systems, which is completely irrelevant for anyone
outside Intel and their early access program. There might be dragons
lurking as usual, but so far the fine grained refactoring has held up
and eventual yet undetected fallout is bisectable and should be
easily addressable before the 5.16 release. Famous last words...
Many thanks to Chang Bae and Dave Hansen for working hard on this and
also to the various test teams at Intel who reserved extra capacity
to follow the rapid development of this closely which provides the
confidence level required to offer this rather large update for
inclusion into 5.16-rc1
* tag 'x86-fpu-2021-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (110 commits)
Documentation/x86: Add documentation for using dynamic XSTATE features
x86/fpu: Include vmalloc.h for vzalloc()
selftests/x86/amx: Add context switch test
selftests/x86/amx: Add test cases for AMX state management
x86/fpu/amx: Enable the AMX feature in 64-bit mode
x86/fpu: Add XFD handling for dynamic states
x86/fpu: Calculate the default sizes independently
x86/fpu/amx: Define AMX state components and have it used for boot-time checks
x86/fpu/xstate: Prepare XSAVE feature table for gaps in state component numbers
x86/fpu/xstate: Add fpstate_realloc()/free()
x86/fpu/xstate: Add XFD #NM handler
x86/fpu: Update XFD state where required
x86/fpu: Add sanity checks for XFD
x86/fpu: Add XFD state to fpstate
x86/msr-index: Add MSRs for XFD
x86/cpufeatures: Add eXtended Feature Disabling (XFD) feature bit
x86/fpu: Reset permission and fpstate on exec()
x86/fpu: Prepare fpu_clone() for dynamically enabled features
x86/fpu/signal: Prepare for variable sigframe length
x86/signal: Use fpu::__state_user_size for sigalt stack validation
...
|
|
DM&P devices were not being properly identified, which resulted in
unneeded Spectre/Meltdown mitigations being applied.
The manufacturer states that these devices execute always in-order and
don't support either speculative execution or branch prediction, so
they are not vulnerable to this class of attack. [1]
This is something I've personally tested by a simple timing analysis
on my Vortex86MX CPU, and can confirm it is true.
Add identification for some devices that lack the CPUID product name
call, so they appear properly on /proc/cpuinfo.
¹https://www.ssv-embedded.de/doks/infos/DMP_Ann_180108_Meltdown.pdf
[ bp: Massage commit message. ]
Signed-off-by: Marcos Del Sol Vives <marcos@orca.pet>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211017094408.1512158-1-marcos@orca.pet
|
