| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Handling case err == 0 in the other branch allows to simplify the
code. In addition I assume in "err & phydev->eee_cfg.tx_lpi_enabled"
it should have been a logical and operator. It works as expected also
with the bitwise and, but using a bitwise and with a bool value looks
ugly to me.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/de37bf30-61dd-49f9-b645-2d8ea11ddb5d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MAC driver changes its EEE hardware configuration in its
adjust_link callback. This is called when auto-neg
completes. Disabling EEE via eee_enabled false will trigger an
autoneg, and as a result the adjust_link callback will be called with
phydev->enable_tx_lpi set to false. Similarly, eee_enabled set to true
and with a change of advertised link modes will result in a new
autoneg, and a call the adjust_link call.
If set_eee is called with only a change to tx_lpi_enabled which does
not trigger an auto-neg, it is necessary to call the adjust_link
callback so that the MAC is reconfigured to take this change into
account.
When setting phydev->enable_tx_lpi, take both eee_enabled and
tx_lpi_enabled into account, so the MAC drivers just needs to act on
phydev->enable_tx_lpi and not the whole EEE configuration.
The same check should be done for tx_lpi_timer too.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240302195306.3207716-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Have phylib keep track of the EEE configuration. This simplifies the
MAC drivers, in that they don't need to store it.
Future patches to phylib will also make use of this information to
further simplify the MAC drivers.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MAC drivers which support EEE need to know the results of the EEE
auto-neg in order to program the hardware to perform EEE or not. The
oddly named phy_init_eee() can be used to determine this, it returns 0
if EEE should be used, or a negative error code,
e.g. -EOPPROTONOTSUPPORT if the PHY does not support EEE or negotiate
resulted in it not being used.
However, many MAC drivers get this wrong. Add phydev->enable_tx_lpi
which indicates the result of the autoneg for EEE, including if EEE is
administratively disabled with ethtool. The MAC driver can then access
this in the same way as link speed and duplex in the adjust link
callback. If enable_tx_lpi is true, the MAC should send low power
indications and does not need to consider anything else with respect
to EEE.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Device driver structures are shared between all devices that they
match, and thus nothing should never write to the device driver
structure through the phydev->drv pointer. Let's make this pointer
const to catch code that attempts to do so.
Suggested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1rVxXt-002YqY-9G@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__phy_hwtstamp_set function were calling the phy_mii_ioctl function
which will then use the ifreq pointer to call the hwtstamp callback.
Now that ifreq has been removed from the hwstamp callback parameters
it seems more logical to not go through the phy_mii_ioctl function and pass
directly kernel_hwtstamp_config parameter to the hwtstamp callback.
Lets do the same for __phy_hwtstamp_get function and return directly
EOPNOTSUPP as SIOCGHWTSTAMP is not supported for now for the PHYs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHYs hwtstamp callback are still getting the timestamp config from
ifreq and using copy_from/to_user.
Get rid of these functions by using timestamp configuration in parameter.
This also allow to move on to kernel_hwtstamp_config and be similar to
net devices using the new ndo_hwstamp_get/set.
This adds the possibility to manipulate the timestamp configuration
from the kernel which was not possible with the copy_from/to_user.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek reports that a deadlock occurs with the AX88772A PHY used on the
ASIX USB network driver:
asix 1-1.4:1.0 (unnamed net_device) (uninitialized): PHY [usb-001:003:10] driver [Asix Electronics AX88772A] (irq=POLL)
Asix Electronics AX88772A usb-001:003:10: attached PHY driver(mii_bus:phy_addr=usb-001:003:10, irq=POLL)
asix 1-1.4:1.0 eth0: register 'asix' at usb-12110000.usb-1.4, ASIX AX88772 USB 2.0 Ethernet, a2:99:b6:cd:11:eb
asix 1-1.4:1.0 eth0: configuring for phy/internal link mode
============================================
WARNING: possible recursive locking detected
6.6.0-rc1-00239-g8da77df649c4-dirty #13949 Not tainted
--------------------------------------------
kworker/3:3/71 is trying to acquire lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_start_aneg+0x1c/0x38
but task is already holding lock:
c6c704cc (&dev->lock){+.+.}-{3:3}, at: phy_state_machine+0x100/0x2b8
This is because we now consistently call phy_process_state_change()
while holding phydev->lock, but the AX88772A PHY driver then goes on
to call phy_start_aneg() which tries to grab the same lock - causing
deadlock.
Fix this by exporting the unlocked version, and use this in the PHY
driver instead.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: ef113a60d0a9 ("net: phy: call phy_error_precise() while holding the lock")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1qiEFs-007g7b-Lq@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert phy_stop() to use the new locked-section and unlocked-section
parts of the PHY state machine.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split out the locked and unlocked sections of phy_state_machine() into
two separate functions which can be called inside the phydev lock and
outside the phydev lock as appropriate, thus allowing us to combine
the locked regions in the caller of phy_state_machine() with the
locked region inside phy_state_machine().
This avoids unnecessarily dropping the phydev lock which may allow
races to occur.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move phy_state_machine() before phy_stop() to avoid subsequent patches
introducing forward references.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the call to phy_suspend() to the end of phy_state_machine() after
we release the lock so that we can combine the locked areas.
phy_suspend() can not be called while holding phydev->lock as it has
caused deadlocks in the past.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the call to start auto-negotiation inside the lock in the PHYLIB
state machine, calling the locked variant _phy_start_aneg(). This
avoids unnecessarily releasing and re-acquiring the lock.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the locking out of phy_error_precise() and to its only call site,
merging with the locked region that has already been taken.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_stop() calls phy_process_state_change() while holding the phydev
lock, so also arrange for phy_state_machine() to do the same, so that
this function is called with consistent locking.
Tested-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
c274af224269 ("inet: introduce inet->inet_flags")
https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/
Adjacent changes:
drivers/net/bonding/bond_alb.c
e74216b8def3 ("bonding: fix macvlan over alb bond support")
f11e5bd159b0 ("bonding: support balance-alb with openvswitch")
drivers/net/ethernet/broadcom/bgmac.c
d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()")
23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()")
drivers/net/ethernet/broadcom/genet/bcmmii.c
32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()")
acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()")
net/sctp/socket.c
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 91a7cda1f4b8 ("net: phy: Fix race condition on link status
change") all the phy_error() method invocations have been causing the
nested-mutex-lock deadlock because it's normally done in the PHY-driver
threaded IRQ handlers which since that change have been called with the
phydev->lock mutex held. Here is the calls thread:
IRQ: phy_interrupt()
+-> mutex_lock(&phydev->lock); <--------------------+
drv->handle_interrupt() | Deadlock due
+-> ERROR: phy_error() + to the nested
+-> phy_process_error() | mutex lock
+-> mutex_lock(&phydev->lock); <-+
phydev->state = PHY_ERROR;
mutex_unlock(&phydev->lock);
mutex_unlock(&phydev->lock);
The problem can be easily reproduced just by calling phy_error() from any
PHY-device threaded interrupt handler. Fix it by dropping the phydev->lock
mutex lock from the phy_process_error() method and printing a nasty error
message to the system log if the mutex isn't held in the caller execution
context.
Note for the fix to work correctly in the PHY-subsystem itself the
phydev->lock mutex locking must be added to the phy_error_precise()
function.
Link: https://lore.kernel.org/netdev/20230816180944.19262-1-fancer.lancer@gmail.com
Fixes: 91a7cda1f4b8 ("net: phy: Fix race condition on link status change")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/core/dev_ioctl.c (built-in code) will want to call phy_mii_ioctl()
for hardware timestamping purposes. This is not directly possible,
because phy_mii_ioctl() is a symbol provided under CONFIG_PHYLIB.
Do something similar to what was done in DSA in commit 5a17818682cf
("net: dsa: replace NETDEV_PRE_CHANGE_HWTSTAMP notifier with a stub"),
and arrange some indirect calls to phy_mii_ioctl() through a stub
structure containing function pointers, that's provided by phylib as
built-in even when CONFIG_PHYLIB=m, and which phy_init() populates at
runtime (module insertion).
Note: maybe the ownership of the ethtool_phy_ops singleton is backwards,
and the methods exposed by that should be later merged into phylib_stubs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230801142824.1772134-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When taking a network interface down (or removing a SFP module) after
the PHY has encountered an error, phy_stop() complains incorrectly
that it was called from HALTED state.
The reason this is incorrect is that the network driver will have
called phy_start() when the interface was brought up, and the fact
that the PHY has a problem bears no relationship to the administrative
state of the interface. Taking the interface administratively down
(which calls phy_stop()) is always the right thing to do after a
successful phy_start() call, whether or not the PHY has encountered
an error.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
6e9d51b1a5cb ("net/mlx5e: Initialize link speed to zero")
1bffcea42926 ("net/mlx5e: Add devlink hairpin queues parameters")
https://lore.kernel.org/all/20230324120623.4ebbc66f@canb.auug.org.au/
https://lore.kernel.org/all/20230321211135.47711-1-saeed@kernel.org/
Adjacent changes:
drivers/net/phy/phy.c
323fe43cf9ae ("net: phy: Improved PHY error reporting in state machine")
4203d84032e2 ("net: phy: Ensure state transitions are processed from phy_stop()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the PHY library calls phy_error() something bad has happened, and
we halt the PHY state machine. Calling phy_error() from the main state
machine however is not precise enough to know whether the issue is
reading the link status or starting auto-negotiation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the phy_disconnect() -> phy_stop() path, we will be forcibly setting
the PHY state machine to PHY_HALTED. This invalidates the old_state !=
phydev->state condition in phy_state_machine() such that we will neither
display the state change for debugging, nor will we invoke the
link_change_notify() callback.
Factor the code by introducing phy_process_state_change(), and ensure
that we process the state change from phy_stop() as well.
Fixes: 5c5f626bcace ("net: phy: improve handling link_change_notify callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phydev lock should be held while accessing members of phydev,
or calling into the driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All preparations are done. Now we can start using new functions and remove
the old code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce code duplicated by migrating phy_init_eee() to
genphy_c45_eee_is_active().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous attempt to augment carrier_down (see Link)
was not met with much enthusiasm so let's do the simple
thing of exposing what some devices already maintain.
Add a common ethtool statistic for link going down.
Currently users have to maintain per-driver mapping
to extract the right stat from the vendor-specific ethtool -S
stats. carrier_down does not fit the bill because it counts
a lot of software related false positives.
Add the statistic to the extended link state API to steer
vendors towards implementing all of it.
Implement for bnxt and all Linux-controlled PHYs. mlx5 and (possibly)
enic also have a counter for this but I leave the implementation
to their maintainers.
Link: https://lore.kernel.org/r/20220520004500.2250674-1-kuba@kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221104190125.684910-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).
This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.
For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.
802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00a4 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e77 ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As reported by Zhang there's a small issue if in forced mode the duplex
mode changes with the link staying up [0]. In this case the MAC isn't
notified about the change.
The proposed patch relies on the phylib state machine and ignores the
fact that there are drivers that uses phylib but not the phylib state
machine. So let's don't change the behavior for such drivers and fix
it w/o re-adding state PHY_FORCING for the case that phylib state
machine is used.
[0] https://lore.kernel.org/netdev/a5c26ffd-4ee4-a5e6-4103-873208ce0dc5@huawei.com/T/
Fixes: 2bd229df5e2e ("net: phy: remove state PHY_FORCING")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7b8b9456-a93f-abbc-1dc5-a2c2542f932c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix following format issues:
1. open brace '{' following function definitions should go to the next
line.
2. braces {} are not necessary for single line statements.
3. else should follow close brace '}'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case phy_state_machine() works on top of USB device, we can get -ENODEV
at any point. So, be less noisy if device was removed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch to lockdep_assert_held(_once), similar to what is being done
in other subsystems. One advantage is that there's zero runtime
overhead if lockdep support isn't enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that all the PHY drivers have been migrated to directly implement
the generic .handle_interrupt() callback for a seamless support of
shared IRQs and all the .config_inter() implementations clear any
pending interrupts, we can safely remove the two callbacks.
With this patch, phylib has a proper support for shared IRQs (and not
just for multi-PHY devices. A PHY driver must implement both the
.handle_interrupt() and .config_intr() callbacks for the IRQs to be
actually used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some functions have different names between their prototypes
and the kernel-doc markup.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
