1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2017-2018 NXP
* Copyright (C) 2019 Oliver Graute <oliver.graute@kococonnector.com>
*/
#include <common.h>
#include <cpu_func.h>
#include <env.h>
#include <errno.h>
#include <init.h>
#include <asm/global_data.h>
#include <linux/delay.h>
#include <linux/libfdt.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/clock.h>
#include <asm/arch/sci/sci.h>
#include <asm/arch/imx8-pins.h>
#include <asm/arch/iomux.h>
#include <asm/arch/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL ((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
static iomux_cfg_t uart0_pads[] = {
SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static void setup_iomux_uart(void)
{
imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
}
int board_early_init_f(void)
{
sc_pm_clock_rate_t rate = SC_80MHZ;
int ret;
/* Set UART0 clock root to 80 MHz */
ret = sc_pm_setup_uart(SC_R_UART_0, rate);
if (ret)
return ret;
setup_iomux_uart();
/* This is needed to because Kernel do not Power Up DC_0 */
sc_pm_set_resource_power_mode(-1, SC_R_DC_0, SC_PM_PW_MODE_ON);
sc_pm_set_resource_power_mode(-1, SC_R_GPIO_5, SC_PM_PW_MODE_ON);
return 0;
}
#if IS_ENABLED(CONFIG_FEC_MXC)
#include <miiphy.h>
int board_phy_config(struct phy_device *phydev)
{
#ifdef CONFIG_FEC_ENABLE_MAX7322
u8 value;
/* This is needed to drive the pads to 1.8V instead of 1.5V */
i2c_set_bus_num(CONFIG_MAX7322_I2C_BUS);
if (!i2c_probe(CONFIG_MAX7322_I2C_ADDR)) {
/* Write 0x1 to enable O0 output, this device has no addr */
/* hence addr length is 0 */
value = 0x1;
if (dm_i2c_write(CONFIG_MAX7322_I2C_ADDR, 0, 0, &value, 1))
printf("MAX7322 write failed\n");
} else {
printf("MAX7322 Not found\n");
}
mdelay(1);
#endif
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif
int checkboard(void)
{
puts("Board: ROM-7720-A1 4GB\n");
build_info();
print_bootinfo();
return 0;
}
int board_init(void)
{
/* Power up base board */
sc_pm_set_resource_power_mode(-1, SC_R_BOARD_R1, SC_PM_PW_MODE_ON);
return 0;
}
/*
* Board specific reset that is system reset.
*/
void reset_cpu(void)
{
/* TODO */
}
int board_mmc_get_env_dev(int devno)
{
return devno;
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
env_set("board_name", "ROM-7720-A1");
env_set("board_rev", "iMX8QM");
#endif
env_set("sec_boot", "no");
#ifdef CONFIG_AHAB_BOOT
env_set("sec_boot", "yes");
#endif
return 0;
}
|